Home

User manual of DS-2AE7164

1. HIKVISION IR Speed Dome User Manual V1 0 0 UD 6L0201D1030A01 User Manual of IR Speed Dome Thank you for purchasing our product If there is any question or request please do not hesitate to contact the dealer This manual is applicable to IR Speed Dome This manual may contain several technically inaccurate points or printing errors and the content is subject to change without notice The updates will be added into the new version of this manual We will readily improve or update the products or procedures described in the manual DISCLAIMER STATEMENT Underwriters Laboratories Inc UL has not tested the performance or reliability of the security or signaling aspects of this product UL has only tested for fire shock or casualty hazards as outlined in UL s Standard s for Safety UL60950 1 UL Certification does not cover the performance or reliability of the security or signaling aspects of this product UL MAKES NO REPRESENTATIONS WARRANTIES OR CERTIFICATIONS WHATSOEVER REGARDING THE PERFORMANCE OR RELIABILITY OF ANY SECURITY OR SIGNALING RELATED FUNCTIONS OF THIS PRODUCT E Hikvision Digital Technology Co Ltd All Rights Reserved User Manual of IR Speed Dome Regulatory Information FCC Information FCC compliance This equipment has been tested and found to comply with the limits for a digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against
2. Task 1 Configure the focus settings Setting the focus mode Steps 1 Move the cursor to FOCUS using the direction buttons and click IRIS to enter 2 Click up down direction buttons to set the focus mode to AF MF or HAF AF Auto focus The lens remains in focus during PTZ movements MF Manual Focus You need to adjust the focus with Focus and Focus buttons manually HAF Half auto Focus The speed dome focuses automatically only once after panning tilting and zooming 3 Click IRIS button to save the settings Setting the focus limit Purpose This function is used to limit the minimum focus distance You can configure the focus limit longer when the target is at a distance to avoid the speed dome focusing on the objects close to it or configure the focus limit shorter when the target is near the speed dome and avoid it focuses on the objects father You can set FOCUS LIMT to 1CM 30CM 1M 3M and AUTO to make sure that the speed dome focuses on the target Note The focus limit value varies according to the models of speed dome Task 2 Configure the zoom settings Setting the zoom limit E Hikvision Digital Technology Co Ltd All Rights Reserved User Manual of IR Speed Dome Purpose Zoom limit is a user defined limitation of the zoom amount Zoom amount optical zoom digital zoom If you set the zoom limit to the minimum value the digital zoom will be invalid and the optical zoom will reach the maximum value
3. Steps 1 Move the cursor to EDIT PATROL and click IRIS to enter edit mode NUM PRESET DWELL SPEED 6 30 30 30 30 30 30 0 30 DONE OPEN QUIT CLOSE Figure 3 14 Edit the Patrol 2 Click up down direction buttons to choose the number and locate the preset to be edited 3 Click left right direction buttons to position the cursor to the column of PRESET DWELL and SPEED You can click the up down direction buttons to set the value of preset number dwell time and patrol speed Note The presets you set for a patrol should be the ones that have been pre defined by users The dwell time 0 30 seconds selectable is the time that the speed dome stays on a certain preset the patrol speed level 1 40 selectable is the scanning speed the speed dome switching between the presets 4 Follow the above steps to define the other presets for the selected patrol You can configure up to 32 presets in sequence for a patrol Press IRIS to save the new settings or press IRIS E Hikvision Digital Technology Co Ltd All Rights Reserved User Manual of IR Speed Dome to cancel and return to the previous menu 4 Preview the patrol Move the cursor to PREVIEW and click IRIS to preview the current patrol You can click IRS again to stop the preview 5 Call the defined patrol You can call the special presets to call the defined patrol E g call preset 35 to call patrol 1 Please refer to Section 2 3 to find the corresponding preset nu
4. The programmable actions include pan scan random scan patrol 1 8 pattern 1 4 preset 1 8 frame scan panorama scan tilt scan day night and none Park Action This feature allows the dome to start a predefined action automatically after a period of inactivity E Hikvision Digital Technology Co Ltd All Rights Reserved User Manual of IR Speed Dome Chapter 2 Getting Started 2 1 Power up Action After the speed dome is power on it will perform a series of self test actions It runs the pan checking firstly then the tilt checking and the camera checking at last After the power up actions the system information will be displayed for 2 minutes on the live view screen as shown below ADDRESS 0 COM FORMAT 2400 8 1 PROTOCOL SELF ADAPTIVE VERSION XXX HARDVERSION XXX BUILD DATE XX XX XX Figure 2 1 System Information Table 2 1 Descriptions of the System Information Description The model of the speed dome The serial number of the speed dome The default communication address of the speed dome The communication settings of the speed dome including baudrate 2400 by default data bit 8 by default and stop bit 1 by default It is for the communication with other devices The version of the firmware The version of the hardware The date when the program of the software is compiled Notes You have to configure the address and the baudrate for the speed do
5. and IR correction etc Enter the LED parameter submenu MAIN MENU gt DOME SETTINGS gt SYS INFO SETTINGS gt IR PARAMETER E Hikvision Digital Technology Co Ltd All Rights Reserved User Manual of IR Speed Dome IR PARAMETER IR PARAMETER IR SENSITIVITY MEDIUM FAN CONTROL TEMP N M LED CURRENT 8 SWITCH DELAY SEC 8 FAR LED CURRENT 8 HEAT CONTROL TEMP REFERENCE HEIGHT 4 IR CORRECTION N A REFERENCE ZOOM 5 LED CONTROL CLOSE BACK EXIT BACK EXIT Figure 3 7 IR Parameter Set the sensitivity of the IR LED You can set the IR SENSITIVITY to HIGH MEDIUM or LOW Set the electricity level of the IR LED The N M LED CURRENT and the FAR LED CURRENT refer to the electricity level of the near middle IR LED and far IR LED correspondingly You can set the near far LED current and the far LED current to HIGH MEDIUM and LOW IR LED switching settings e REFERENCE HEIGHT Reference height refers to the mounting height of the speed dome This value is for switching between near medium distance IR LED and far distance IR LED e REFERENCE ZOOM When the actual zooming rate is larger than the reference zoom it will switch to the far distance IR LED when it s smaller than the reference zoom it will switch to the near medium distance IR LED e LED CONTROL LED control can be set to ALL ON enable all the IR LED FAR ON enable far distance IR LED NEAR ON enable near medium distance IR LED AUTO enable IR LED automatic
6. AUTO MATCH SOFT BAUD 2400 IR PARAMETER 485CHECK SET AUTO SOFT BAUD ACTIVE OFF FAN CONTROL POWER MEMORY 180S BROADCAST ADDRESS ON EIS FUNCTION PELCO CHECKSUM ON EIS LEVEL SYS TIME PRESET DFOCUS BACK EXIT BACK EXIT BACK EXIT Figure 3 4 System Information Settings Note You can click the left and right direction buttons in the PTZ control panel via the web browser of the encoder to enter the next page and return to the previous page of the submenu if more than one page is available e Dome address settings To Set the Soft Address of the Speed Dome If the SOFT ADDR ACTIVE is set as ON the soft address is the valid address for connecting the speed dome The selectable soft address range is from 1 to 255 If the SOFT ADDR ACTIVE is set as OFF the hard address set by the DIP switch is the valid address of the speed dome Notes e Before you set the soft address of the speed dome you need to confirm that it is within the control range of the control device e g the DVR E Hikvision Digital Technology Co Ltd All Rights Reserved User Manual of IR Speed Dome e After you enable disable the soft address the speed dome will reboot automatically to activate the settings To Set the Broadcast Address of the Speed Dome When the BROADCAST ADDRESS is set to ON the control device with address O is capable of controlling all domes connected to it e Soft Baud Rate Settings If the SOFT BAUD ACTIVE is set as ON the soft baud rate is the v
7. automatically adjust in size as the lens zooms telephoto and wide 3D Positioning In the client software use the left key of mouse to click on the desired position in the video image and drag a rectangle area in the lower right direction then the dome system will move the position to the center and allow the rectangle area to zoom in Use the left key of mouse to drag a rectangle area in the upper left direction to move the position to the center and allow the rectangle area to zoom out Proportional Pan Tilt Proportional pan tilt automatically reduces or increases the pan and tilt speeds according to the amount of zoom At telephoto zoom settings the pan and tilt speeds will be slower than at wide zoom settings This keeps the image from moving too fast on the live view image when there is a large amount of zoom Auto Focus The auto focus enables the camera to focus automatically to maintain clear video images Day Night Auto Switch The speed domes deliver color images during the day And as light diminishes at night the speed domes switch to night mode and deliver black and white images with high quality Slow Shutter In slow shutter mode the shutter speed will automatically slowdown in low illumination conditions to maintain clear video images by extending the exposure time The feature can be enabled or disabled Backlight Compensation BLC If you focus on an object against strong backlight the object will be too dar
8. click IRIS again to clear the stops Elevation set You can set ELEVATION SET as ON to increase the elevation angle range of the speed dome or set it as OFF to disable the function Note The range of the elevation angle is 0 90 by default and it changes to 2 90 when the ELEVATION SET is set as ON 3 4 2 Configuring Presets Purpose A preset is a user defined monitoring position point You can simply call the preset number to change the monitor scene to the defined position Steps 1 Move the cursor to enter preset configuration submenu MAIN MENU gt DOME SETTINGS gt PRESETS E Hikvision Digital Technology Co Ltd All Rights Reserved User Manual of IR Speed Dome PRESETS PRESET NUM UNDEFINED PRESET PTZ CLEAR PRESET BACK EXIT Figure 3 12 Preset Configuration Menu 2 Choose the preset number Move the cursor to PRESET NUM and click IRIS to enter Click the up and down buttons to choose the preset number which needs to be edited If the preset has been defined the preset label will be listed under the number if it has not been defined you will see the information UNDEFINED under the number Notes There are up to 255 presets can be set for the speed dome The system defined presets will be displayed on this submenu and they are not editable 3 Set the preset position Move the cursor to PRESET PTZ and click IRIS to edit the preset position Use the direction buttons to move the speed dome to
9. for specific battery information The battery is marked with this symbol which may include lettering to indicate cadmium Cd lead Pb or mercury Hg For proper recycling return the battery to your supplier or to a designated collection point For more information see www recyclethis info C This product and if applicable the supplied accessories too are marked with CE 0100001030406 E Hikvision Digital Technology Co Ltd All Rights Reserved User Manual of IR Speed Dome Safety Instruction These instructions are intended to ensure that the user can use the product correctly to avoid danger or property loss The precaution measure is divided into Warnings and Cautions Warnings Serious injury or death may be caused if any of these warnings are neglected Cautions Injury or equipment damage may be caused if any of these cautions are neglected A A Warnings Follow these safeguards to Cautions Follow these precautions to prevent serious injury or death prevent potential injury or material damage AA Please adopt the power adapter which can meet the safety extra low voltage SELV standard And source with 24VAC 10 or 12VDC 10 depending on models according to the IEC60950 1 and Limited Power Source standard The power consumption cannot be less than the required value Do not connect several devices to one power adapter as an adapter overload may cause over heating and ca
10. if you set the zoom limit smaller the digital zoom will be enabled Steps 1 Move the cursor to ZOOM LIMIT using the direction buttons and click IRIS to enter 2 Click up down direction buttons to choose the limit from 22 44 88 176 and 352 3 Click IRIS button to confirm Note If you set the ZOOM LIMIT as the minimum value 22 the digital zoom function will be disabled and the optical zoom function is at its maximum value Configure the zoom speed Purpose You can define the speed at which the lens changes from full wide zoom to the optical zoom Steps 1 Move the cursor to ZOOM SPEED using the direction buttons and click IRIS to enter 2 Click up down direction buttons to choose the speed from HIGH default MEDUIM and LOW 3 Click IRIS button to confirm Task 3 Configure the Day Night mode There are two parameters available for day night mode configuration 1 IR cut filter It can be set as AUTO DAY or NIGHT AUTO The speed dome is capable of automatically switching from Black and White mode NIGHT and Color mode DAY regarding to the lightening conditions It is the default mode NIGHT B W You can switch the IR cut filter into Black and White mode to increase then lens sensitivity in low light conditions DAY Color You can switch it to DAY mode in normal lighting conditions Note You can set the IRCUT FILTER value on this menu and you can call preset 39 to set the IR cut filter mode to DAY mod
11. shape of cursor changes Click the up down or left right buttons in the PTZ control panel to choose the value from the selectable value list Press IRIS to confirm the change or click IRIS to cancel and restore the original value You can see the shape of cursor changes again 3 2 Configuring System Information 3 2 1 Checking System Information Purpose System information menu displays the current system information of the speed dome including model address protocol etc The information shown on this submenu is similar to the system information shown after the power up action Please refer to Section 2 1 for more details Enter the system information display menu MAIN MENUS gt SYS INFO E Hikvision Digital Technology Co Ltd All Rights Reserved User Manual of IR Speed Dome SYS INFO ADDRESS 0 COM FORMAT 2400 8 1 PROTOCOL SELF ADAPTIVE VERSION 1 00 HARDVERSION 1 00 BUILD DATE 13 04 01 TEMPERATURE 38 C BACK EXIT Figure 3 3 System Information Notes Information on this menu cannot be edited The temperature refers to the internal temperature of the speed dome 3 2 2 Configuring System Parameters Purpose You can check and also edit the system information of software address baud rate system time etc on the system information settings menu SYS INFO SETTINGS SYS INFO SETTINGS SYS INFO SETTINGS SOFT ADDRESS 1 ZERO ANGLE PROTOCOL STATUS SET OFF SOFT ADDR ACTIVE OFF DISPLAY SETTINGS PROTOCOL SET
12. 3 40 70 21 112 34 179 54 452 137 50 56 17 90 27 143 43 362 110 60 47 14 75 22 119 36 301 91 70 40 12 64 19 102 31 258 78 80 35 10 56 17 89 27 226 68 90 31 9 50 15 79 24 201 61 100 28 8 45 13 71 21 181 55 110 25 7 41 12 65 19 164 49 120 23 7 37 11 59 17 150 45 130 21 6 34 10 55 16 139 42 140 20 6 32 9 51 15 129 39 150 18 5 30 9 47 14 120 36 160 17 5 28 8 44 13 113 34 170 16 4 26 7 42 12 106 32 180 15 4 25 7 39 11 100 30 190 14 4 23 7 37 11 95 28 200 14 4 22 6 35 10 90 27 E Hikvision Digital Technology Co Ltd All Rights Reserved User Manual of IR Speed Dome Appendix 4 Table of Wire Gauge Standards American on Cross sectional Bare Wire British Wire Get Wire Gauge Gauge SWG ee of Bare AWG Wire mm2 0 750 21 0 4417 0 800 20 21 0 5027 0 900 19 20 0 6362 1 000 18 19 0 7854 1 250 16 18 1 2266 1 500 15 17 1 7663 2 000 12 14 3 1420 2 500 4 9080 3 000 7 0683 E Hikvision Digital Technology Co Ltd All Rights Reserved First Choice for Security Professionals HANGZHOU HIKVISION DIGITAL TECHNOLOGY CO LTD www hikvision com
13. Beete reeller deele ae 11 Chapter 3 M nu Operati EE 12 3 1 Accessing and Operating the Menu 12 3 2 Configuring System Information ccccccccccccssssssecececeesesseaesecececseseeaeseeeceseesneaeseseesceesesaeeeseceesesssasseseesesesesaeaeeeeess 13 3 21 Checking System ere ET E 13 3 2 2 Configuring System Dorometers nn 14 3 3 Configuring Image Parametere 18 3 3 1 Config ring Camera Paramet ts oe eeraa ea raa Aani Ap AEAT RAT AA ARE AERA AE AAAA ATAARE RAE 18 3 3 2 Configuring Privacy MOSK a ara a a a ck va eaaa aa E a a aaa a A a aa a aaa A a AREE 23 3 4 Configuring PTZ Control Parameters ccccccessscecececessesnsaesecececseseeaeseeececeesneaeseeeesceeseeaeeeseeeseesssaeseseeseseseaeaeeeeess 24 3 4 1 Configuring PTZ Par meterS ou ceeseccccccsessesssnscececeesensessceseceseessaseseseceseessasesesecsceesessesssecsceesesssaesesseseessaaeseseceeeeuea 24 3 42 CONFIGUTING EE 26 343 Configuring EE 27 BAA COOU EE 29 3 4 5 Configuring Time TOSKS cccccscssscesececeesenssaececscesessessseseeeseessaseseseceseessaseeesececeesessesesecseeesessaaesesseseeessaaeseseeseeenea 30 3 4 6 Configuring ZONE arearen neiaint REEE EA ENRE EAEE AEAEE AN AEAEE E NEEE AEREE AA AENA NEEN AEAEE TAREE 32 3 4 7 Clearing PITZ Control Settings E 33 3 5 TEE 34 3 5 1 Configuring DOME Authentication cccssesccccecessessssscecseessessaseceseceseeseasesesecsceeseasssesececessessaaesessesseessaseseseceeeene 34 3 5 2 Restoring Default Dome Settings sccc
14. IR Speed Dome e Display Settings Purpose You can enable or disable the on screen display of PTZ movements alarms time presets zone address error rate and fan heat show etc Steps 1 Move the cursor to DISPLAY SETTINGS using the direction buttons and click IRIS to enter 2 Move the cursor to the target item and click IRIS and click up down direction buttons to choose each display mode as ON or OFF and define each display time as 2 seconds 5 seconds or 10 seconds 3 Click IRIS button to confirm the settings Note If you enable the OSD for both ZOOM and PT while calling a preset the preset No will be displayed on the screen till the preset scene passes DISPLAY SETTINGS DISPLAY SETTINGS ZOOM SHOW 2 FAN AND HEAT SHOW OFF PT SHOW 2 TIME SHOW ON PRESET SHOW ON ZONE SHOW ON ADDRESS SHOW ON ERROR RATE SHOW BACK EXIT BACK EXIT Figure 3 6 Display Settings The speed dome shows the viewing direction when you manually control it to rotate Table 1 2 Viewing Direction Display Display N NE E SE S SW W NW Indication North Northeast East Southeast South Southwest West Northwest Note The north direction refers to the zero angle initial position e IR Parameter Configuration Purpose You can configure the IR parameters including the IR sensitivity n m LED current reference height reference zoom and LED control fan control switch delay heat control
15. MAIN MENU gt DOME SETTINGS gt CLEAR SETTINGS CLEAR SETTINGS CLEAR ALL PRESETS CLEAR ALL PATROLS CLEAR ALL PATTERNS CLEAR ALL BLANKS CLEAR ALL ZONES CLEAR ALL TIME TASKS lt DIAGNOSTICS gt BACK EXIT Figure 3 20 Clear Dome Settings 2 Move the cursor to each item e g CLEAR ALL PATTERNS and click IRIS to enter the corresponding submenu Click IRIS again to confirm the settings and exit On DIAGNOSTICS submenu you can see the self diagnostics information of the speed dome For more details please refer to the table below E Hikvision Digital Technology Co Ltd All Rights Reserved User Manual of IR Speed Dome DIAGNOSTICS HIGH TEMP HIGHEST TEMP LOW TEMP DIAGNOSTICS PAN LOST TILT LOST CAMERA LOST LOWEST TEMP VIDEO LOSS LOW VOLTAGE POWER UP BACK EXIT BACK EXIT Figure 3 21 Self diagnostics Table 1 3 Descriptions of self diagnostics information pte Description OO OO O The occurrence times of high temperature higher than 65 C Note The panning loss and tilting loss refer to the failures of panning and tilting movement and are for diagnosing the electric motor of the speed dome 3 5 Others 3 5 1 Configuring Dome Authentication Purpose You can modify the password and enable disable the password protection to prevent unauthorized settings of the speed dome After you set and enable the password you need to input the password every time you call preset 95 to enter the menu Step
16. RY 100 DONE OPEN QUIT CLOSE Figure 3 16 Edit the Pattern 2 Click the PTZ control buttons and direction buttons to operate the speed dome to draw a movement path including pan scan tilt scan zoom in zoom out etc The speed dome can automatically memorize the path you operated as a pattern 3 Click IRIS again to save the pattern and exit edit mode Notes REMAIN MEMORY indicates the remaining memory of the speed dome for configuring the patterns When it reaches 0 no more patterns can be configured You can also see the remaining memory shown under PATTERNS menu as REMAINING The pan tilt movements and the lens operations cannot be memorized simultaneously 4 Preview the pattern Enter the PREVIEW menu to preview the current pattern 5 Call the defined pattern You can call the special presets to call the defined pattern E g call preset 41 to call pattern 1 Please refer to Section 2 2 to find the corresponding preset number for each pattern 6 Delete the patterns To Delete a Chosen Pattern Click IRIS to enter EIDT PATTERN and you can see DEL PATH ABOVE Click IRIS to delete the pattern Note If you delete the current pattern the following pattern will also be deleted E g if pattern 2 is deleted pattern 3 and pattern 4 will be deleted as well To Clear All the Patterns Enter CLEAR PATTERN menu and click IRIS to delete all the defined patterns 3 4 5 Configuring Time Tasks Purpose A time task
17. UTO INDOOR OUTDOOR SELFDEF self defined ATW auto tracking and HAUTO half auto AUTO In Auto mode the dome retains color balance automatically according to the current color temperature INDOOR OUTDOOR These two modes are for indoor use and outdoor use respectively SELFDEF In this mode you can adjust the color temperature manually to meet your own demand Note In SELFDEF mode you need to adjust the RED and BLUE values manually ATW In auto tracking mode white balance is continuously being adjusted in real time according to the color temperature of the scene illumination HAUTO Selecting this mode the viewed image retains color balance automatically according to the current color temperature Task 9 Configure the image flip If you turn the IMAGE FLIP function on the image will be flipped diagonally along its central axis shown as the mirror reflection of the image Task 10 Configure the INIT LENS You can turn INIT LENS on to trigger a spontaneous lens initiation to ensure the normal operation Task 11 Configure the noise reduction To reduce the image noise you can set the NOISE REDUCE to LOW HIGH MIDDLE and OFF Task 12 Configure the image quality Wide Limit Set the wide limit ON can limit the minimum zoom of the lens Note The wide limit function is supported by certain camera model series Chroma Suppress Set the Chroma suppress to ON can suppress the color noise so as to get the clear and hi
18. You can configure it as AUTO MATCH PELCO P PELCO D HIKVISION KALATEL or VICON When you choose AUTO MATCH it is protocol self adaptive e Set the protocol status Set the PROTOCOL STATUS SET as ON to enable the user defined protocol e Enable the RS 485 configuration diagnosis You can set 485CHECK SET as ON or AUTO for automatic RS 485 configuration diagnosis If the configuration is incorrect an alert will be received if you set the value as AUTO it will automatically stop the diagnosis when no errors exist Power Memory Settings The dome can resume its previous PTZ status or actions after it restarted from a power off You can set the power memory to 10S 30S 60S 180S and 300S 3 3 Configuring Image Parameters 3 3 1 Configuring Camera Parameters Purpose You can set the camera parameters including focus shutter speed iris etc Enter the camera parameters settings menu E Hikvision Digital Technology Co Ltd All Rights Reserved User Manual of IR Speed Dome MAIN MENUS gt DOME SETUP gt CAMERA SETUP CAMERA FOCUS ZOOM LIMIT ZOOM SPEED SLOW SHUTTER IRCUT FILTER D N LEVEL SHARPNESS BACK EXIT CAMERA WHITE BALANCE AUTO RED BLUE IMAGE FLIP FOCUS LIMIT INIT LENS NOISE REDUCE CAMERA BLC WDR BLC LEVEL AE MODE IRIS SHUTTER GAIN EXPOSURE COMP BACK EXIT CAMERA WIDE LIMIT CHROMA SUPPRESS SATURATION CONTRAST HLC HR MODE GAIN LIMIT BACK EXIT BACK EXIT Figure 3 8 Camera Settings
19. alid baud rate for the speed dome with 2400 4800 9600 and 19200 selectable If the SOFT BAUD ACTIVE is set as OFF the baud rate should be set by the DIP switch Note After you enable disable the soft baud rate the speed dome will reboot automatically to activate the settings e PELCO Checksum The PELCO CHECKSUM is used for Pelco P and Pelco D protocols If the video turns to slack or uncontrollable you can set the PELCO CHECKSUM as ON to improve the video quality e System Time Configuration Steps 1 Move the cursor to SYS TIME using the direction buttons and click IRIS to enter 2 Click the left right direction buttons to position the cursor on the specific item year month day or hour minute second of which you want to change the value 3 Click the up down direction buttons to increase decrease the value 4 Click IRIS button to confirm the settings and exit Y M D 12 12 12 H M S 15 33 25 DONE OPEN QUIT CLOSE Figure 3 5 Set the System Time e Zero Angle Initial Position Configuration Purpose You can define the initial position of the speed dome on the ZERO ANGLE submenu Steps 1 Move the cursor to ZERO ANGLE using the direction buttons and click IRIS to enter 2 Click the left right up down direction buttons to adjust the monitor angle of the speed dome 3 Click IRIS button to confirm the settings and exit E Hikvision Digital Technology Co Ltd All Rights Reserved User Manual of
20. ally according to the environment illumination and CLOSE disable IR LED IR LED switch delay The SWITCH DELAY SEC refers to the delay time between the switch of far distance IR LED and N M distance IR LED Fan and heat settings e FAN CONTROL is for adjusting the temperature of the speed dome s circuit board You can set it to ON normally on OFF normally off or TEM change according to the temperature e HEAT CONTROL is also to control the temperature of the speed dome in severe cold E Hikvision Digital Technology Co Ltd All Rights Reserved User Manual of IR Speed Dome surveillance environments which can be set as ON normally on OFF normally off or TEM change according to the temperature IR correction settings This parameter is to correct the focus problems caused by the IR light You can turn IR CORRECTION ON or OFF Note IR correction settings vary according to the different camera models Fan Parameter Configuration You can set the FAN CONTROL as TEMP controlled by the temperature ON or OFF EIS Electronic Image Stabilization Configuration You can set the EIS FUNCTION as ON or OFF and set the EIS LEVEL as 0 3 Note The selectable EIS level varies according to the different camera models Preset Direct Focus You can set the preset direct focus function ON OF on PRESET DFOCUS submenu Protocol and RS 485 settings e Select the protocol Choose the protocol on PROTO SET submenu
21. are necessary to be added The design of lightning protection and grounding of the outdoor devices and cables should be considered together with the lightning protection demand of buildings It also must conform to the related national standards and industrial standards The system should be equipotential grounded The grounding equipment must conform to the demands of system anti jamming and electrical safety both and it must not appear short circuit or mixed circuit with the zero conductor of strong grid When the system is grounded alone the resistance should be no more than 4Q The sectional area of the grounding cable should be no less than 25mm2 For grounding instructions please refer to the Installation Manual of Speed Dome video arrester communicate __ arrester lightning rod porer arrester The speed dome should be in the range of 45 degrees under the lightning rod the resistance of earthing conductor should be smaller than 42 steel jacket Figure A 1 Lightning amp Surge Protection mo Hikvision Digital Technology Co Ltd All Rights Reserved User Manual of IR Speed Dome Appendix 2 RS485 Bus Connection General Property of RS485 Bus According to RS485 industry bus standard RS485 is a half duplex communication bus which has 120Q characteristic impendence the maximum load ability is 32 payloads including controller device and controlled device RS485 Bu
22. camera models PTZ speed E Hikvision Digital Technology Co Ltd All Rights Reserved User Manual of IR Speed Dome Purpose You can define the speed of the dome movements 1 DOME SPEED The manual movement speed of the dome can be set from level 1 to 10 2 SCAN SPEED The scan speed defines the scan degree per second of pan scan tilt scan frame scan random scan and panoramic scan The scan speed is adjustable from level 1 to level 40 and the higher the level is the faster the scan speed is 3 PRESET SPEED The speed of calling a preset can be set from level 1 to 8 The higher level corresponds to the faster speed to call a preset Limit stops Purpose The limit stops are user configurable stops which limit the panning and tilting area of the speed dome There are left right up and down limit stops to define an area Steps 1 Move the cursor to LIMIT STOPS and click FOCUS to set it ON to enable this feature Click IRIS to confirm the new settings 2 Move the cursor to SETTING LIMIT STOPS and click IRIS You will see the message SET LEFT LIMIT on the screen 3 Click the direction buttons in the PTZ panel to configure the left limit stop Click IRIS to confirm the new settings 4 Follow the prompts to configure the right up and down limit stops on the menu Note The new limit stops will overwrite the existed ones by default 5 You can clear the defined limit stops Click IRIS to enter CLEAR STOPS and
23. cannot be to the interface RS485 RS485 controlled 3 The RS485 wire is 3 Reconnect the RS485 wire remotely S S disconnected tightly 4 RS485 wire is broken 4 Change a RS485 wire The speed 1 The connection is loose 1 Reconnect the RS485 wire E Hikvision Digital Technology Co Ltd All Rights Reserved User Manual of IR Speed Dome Problem Possible Reasons To Solve the Problem dome can tightly be 2 RS485 or RS485 wire is 2 Change a RS485 wire controlled broken but not 3 Th dd is too f Geen BEL 3 Add a terminal resistor smoothly from the remote control device 4 Te dd See 4 Add a RS485 distributor connected E Hikvision Digital Technology Co Ltd All Rights Reserved User Manual of IR Speed Dome Appendix 3 24VAC Wire Gauge amp Transmission Distance The following table describes the recommended max distance adopted for the certain wire gauge when the loss rate of 24VAC voltage is less than 10 For the AC driven device the maximum voltage loss rate is 10 allowable For example for a device with the rating power of 80VA which is installed at a distance of 35 feet 10m away from the transformer then 0 8000mm is required as the minimum wire gauge 0 8000 1 000 1 250 2 000 10 283 86 451 137 716 218 1811 551 20 141 42 225 68 358 109 905 275 30 94 28 150 45 238 72 603 18
24. e and call preset 40 to set it as NIGHT mode D N level The D N level is the light level for auto D N mode switch As a dividing line IR cut filter switches between DAY and NIGHT when the light condition reaches the user defined D N level Three levels are selectable HIGH MID default and LOW Note D N level configuration varies according to the different camera models Some models don t support user defined D N level Task 4 Configure the sharpness level The sharpness function can increase the gain of the image and sharpen the edges in the picture to enhance the picture details You can set the SHARPNESS level from 0 to 15 2 Task 5 Configure the BLC and WDR There are two parameters available for BLC and WDR configuration on this menu 1 BLC WDR You can set the value as ON or OFF to enable or disable the functions 2 BLC LEVEL You can manually adjust the backlight compensation level Note BLC level configuration varies according to the different camera models Some models E Hikvision Digital Technology Co Ltd All Rights Reserved User Manual of IR Speed Dome don t support user defined BLC level Task 6 Configuring the iris gain and shutter speed Set the AE Mode Purpose AE mode defines the priority of iris shutter and gain while the speed dome adjusting the brightness of the live view You can change the mode on AE MODE submenu AUTO Auto iris auto shutter and auto gain The speed dome adjusts the value
25. er Steps 1 Move the cursor to BLANK NUM and click IRIS to enter the editing mode 2 Click the up and down direction buttons to select a mask number for configuration 3 Click IRIS again to confirm and exit the editing mode Note The configurable privacy mask number varies according to the camera models 3 Configure the position and size of the privacy mask Steps E Hikvision Digital Technology Co Ltd All Rights Reserved User Manual of IR Speed Dome 1 Move the cursor to SET BLANK and click IRIS button to enter the editing mode as shown in the following figure You can see a privacy mask on the live window ADJUST BLANK POS FOCUS SHIFT STATUS SAVE OPEN QUIT CLOSE Figure 3 10 Set the Privacy Mask 2 You can see ADJUST BLANK POS message on the screen Click the direction buttons to adjust the position of the privacy mask to the designed scene 3 Click FOCUS button and you can see ADJUST BLANK SIZE message on the screen Click the up down buttons to increase decrease the height of the mask and click right left buttons to increase decrease the width of the mask Click IRIS button to save the settings and return to the previous menu and you can see the mask turn to gray 4 To modify the configured mask click IRISt button to enter the SET BLANK menu and click IRIS button again to modify Note The tilt range for configuring the privacy masks is from 0 to 70 4 Enable or disable the privacy mask
26. ettings and exit edit mode of this column 5 Set the task time Steps 1 Move the cursor to TASK TIME and click IRIS to enter edit mode 2 Click the left and right direction buttons to position the cursor to WEEK START H M and END H M 3 Click the up and down direction buttons to set the start time and end time to run the time task 4 Click IRIS to confirm the settings and exit Note The weekday can be set to be from Monday to Sunday or Whole Week the H refers to E Hikvision Digital Technology Co Ltd All Rights Reserved User Manual of IR Speed Dome Hour and the M refers to Minute WEEK WHOLE WEEK START H M o0 00 END H M 00 00 DONE OPEN QUIT CLOSE Figure 3 18 Set the Task Time 6 Delete the task Move the cursor to TASK CLEAR click IRIS to delete the time and action of the current task and click IRIS again to confirm the settings and exit 3 4 6 Configuring Zone Purpose A zone is a panning and tilting area defined by the left right and up down limit stops You can configure the zones on ZONES submenu You can define a zone when the targeted surveillance scene is limited Steps 1 Move the cursor to enter the zone configuration submenu MAIN MENU gt DOME SETTINGS gt ZONES ZONES ZONE NUM UNDEFINED EDIT ZONE ZONE STATUS SCAN STATUS CLEAR ZONE BACK Figure 3 19 Zone Configuration 2 Choose the zone number 1 Move the cursor to ZONE NUM and click IRIS button
27. find the desired scene position and then press IRIS to confirm the settings and return to the previous menu or press IRIS to cancel Note The preset position settings will be restricted by the limit stops if they are defined 4 Call the presets You can select the preset number from the drop down preset list in the control panel of the encoder through a web browser and click the arrow to call a user defined or system defined preset 5 Clear the preset settings Move the cursor to CLEAR PRESET and click IRIS to clear the settings of the current preset 3 4 3 Configuring Patrols Purpose A patrol is a scanning track specified by a group of user defined presets You can call a patrol to scan the scenes automatically among the user defined presets in sequence Steps 1 Move the cursor to enter patrol configuration submenu MAIN MENU gt DOME SETTINGS gt PATROLS E Hikvision Digital Technology Co Ltd All Rights Reserved User Manual of IR Speed Dome PATROLS PATROL NUM EDIT PATROL PREVIEW CLEAR PATH PATROL_D BACK EXIT Figure 3 13 Patrol Configuration Menu 2 Choose the patrol number Steps 1 Move the cursor to PATROLS NUM and click IRIS to enter edit mode 2 Click the up and down direction buttons to select the number of the patrol which is to be configured 3 Click IRIS again to confirm the settings and exit edit mode of this column Note Up to 8 patrols can be configured 3 Edit the patrol
28. function Move the cursor to BLANK STATUS Click IRIS button to enter the editing mode and click the up and down direction buttons to set it ON or OFF Note If no privacy mask has been configured you cannot set the status as ON 5 Delete the privacy mask You can enter the DELE BLANK menu to delete the current privacy mask 3 4 Configuring PTZ Control Parameters Purpose You can configure panning tilting and zooming movements and configure PTZ control functions including presets patrols patterns etc for the speed dome 3 4 1 Configuring PTZ Parameters Enter PTZ configuration menu MAIN MENU gt DOME SETTINGS gt MOTION PARAMETER E Hikvision Digital Technology Co Ltd All Rights Reserved User Manual of IR Speed Dome MOTION PRESET SPEED LIMIT STOP lt SETTING STOPS gt CLEAR STOPS ELEVATION SET MOTION AUTO FLIP ON PROPORTIONAL PAN ON PARK TIME 5 PARK ACT NONE SCAN SPEED 28 IMAGE FREEZE OFF DOME SPEED 6 BACK EXIT BACK EXIT Figure 3 11 PTZ Configuration Auto flip In manual tracking mode when a target object goes directly beneath the speed dome the speed dome automatically rotates 180 degrees horizontally for tracking Note AUTO FLIP is set as ON for this speed dome by default and it s not user definable Proportional Panning When the speed dome is zooming in out you can enable the proportional panning function to automatically reduce or increase the panning and tilting speed accord
29. gh quality image in the low luminance environment E Hikvision Digital Technology Co Ltd All Rights Reserved User Manual of IR Speed Dome Note The Chroma Suppress function is supported by certain camera model series Saturation Saturation indicates the brightness of the color The higher the saturation the brighter the color is Note The saturation function is supported by certain camera model series Contrast Contrast is the degree of difference between the darker and lighter parts of the image Note The contrast function is supported by certain camera model series HLC Set the HLC to ON can brighten the darker area and weaken the highlight area of the image Note The HLC function is supported by certain camera model series HR Mode Set the HR MODE as ON to adjust the resolution higher Switch it OFF to disable the function which can avoid cross color of the image 3 3 2 Configuring Privacy Mask Purpose Privacy mask enables you to cover certain areas on the live video from being live viewed and recorded The masked areas can move with the panning tilting movements and automatically adjust the size as the lens zooming in out Steps 1 Move the cursor to enter the privacy mask configuration submenu MAIN MENUS gt DOME SETUP gt PRIVACY SETUP PRIVACY BLANK BLANK NUM 1 BLANK STATUS OFF SET BLANK DELE BLANK BACK EXIT Figure 3 9 Privacy Mask Configuration Menu 2 Choose the privacy mask numb
30. gt 5 gt ENTER on the keyboard Enter the menu via the web browser of a DVR DVS Menu operations via the web browser of a DVR will be taken as an example in this chapter 3 1 Accessing and Operating the Menu To enter the main menu Steps 1 2 3 4 Connect the video and RS 485 cables of speed dome to a DVR Visit the DVR via the web browser View the live video of the speed dome For PELCO P D and other private PTZ protocols call preset 95 from the preset list in the PTZ control panel of the DVR mo Hikvision Digital Technology Co Ltd All Rights Reserved User Manual of IR Speed Dome 5 For some other protocols e g Manchester code control protocol call preset 66 to access the menu Please refer to Table 2 3 for details MAIN MENUS lt SYS INFO gt lt DOME SETTINGS gt lt RESTORE DEFAULTS gt lt RESTORE CAMERA gt lt RESBOOT DOME gt lt LANGUAGE gt ENGLISH lt SET TITLE gt OFF EXIT Figure 3 2 Main Menu To move the cursor and operate the menu Move the cursor up down On the live view page of the web browser click up down direction buttons or FOCUS and FOCUS buttons in the PTZ control panel to move the cursor up and down Enter Exit On the live view page of the web browser click IRIS to enter a submenu move the cursor to Exit and click IRIS to exit To change the value of a parameter Steps 1 Move the cursor to the target item and click IRIS button You can see the
31. harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense FCC Conditions This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation EU Conformity Statement and comply therefore with the applicable harmonized European standards listed under the Low Voltage Directive 2006 95 EC the EMC Directive 2004 108 EC the RoHS Directive 2011 65 EU 2012 19 EU WEEE directive Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union For proper recycling return this product to your local supplier upon the purchase of equivalent new equipment or dispose of it at designated collection points For more information see www recyclethis info 2006 66 EC battery directive This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union See the product documentation
32. ing to the zooming amount This function enables the speed dome to trace the object at a proper speed when the speed dome is Zooming and the monitored scene is narrowed zoom in or enlarged zoom out You can set PROPORTIONAL PAN as ON or OFF to enable disable the function Note This function is enabled automatically while setting the patterns Park time and actions Purpose This feature allows the speed dome to start a predefined action park action scan preset pattern etc automatically after a period of inactivity park time You can set PARK TIME from 5 to 720 seconds and set the park action PARK ACT as preset 1 8 pattern 1 4 patrol 1 8 pan scan tilt scan random scan frame scan panoramic scan day mode night mode or none Note If no control signal is received after the park time under the following circumstances no park actions will be performed in the process of performing dome actions by calling special presets or in the process of performing external alarm linkage actions Image freeze This feature enables the live view to switch directly from the current scene to another scene that is defined by a preset without showing the middle areas between these two scenes It reduces the use of bandwidth in a digital network system and it also provides privacy protection for the middle areas You can set IMAGE FREEZE as ON or OFF to enable or disable this function Note The function varies according to the different
33. is a preconfigured action that can be performed automatically at a specific date and time Steps 1 Move the cursor to enter the TIME TASK submenu E Hikvision Digital Technology Co Ltd All Rights Reserved User Manual of IR Speed Dome MAIN MENU gt DOME SETTINGS gt TIME TASK TIME TASK TASK NUM TASK STATE TASK ACTION TASK TIME TASK PREVIEW TASK CLEAR BACK EXIT Figure 3 17 Time Task Configuration Menu 2 Choose the task number Steps 1 Move the cursor to TASK NUM and click IRIS to enter edit mode 2 Click the up down direction buttons to select the number of the task which is to be configured 3 Click IRIS again to confirm the settings and exit the edit mode Note Up to 8 time tasks can be configured 3 Set the task status Steps 1 Move the cursor to TASK STATE and click IRIS to enter edit mode 2 Click the up down direction buttons to set the task status to ON 3 Click IRIS again to confirm the settings and exit edit mode of this column Note If the task action and task time have not been configured you cannot set the status as ON 4 Configure the task action Steps 1 Move the cursor to TASK ACTION and click the IRIS to enter edit mode 2 Click the up and down direction buttons to select the task action from preset 1 8 pattern 1 4 patrol 1 8 pan scan tilt scan random scan frame scan panoramic scan day mode night mode and none 3 Click IRIS again to confirm the s
34. k to be seen clearly The BLC Backlight Compensation function can compensate light to the object in the front to make it clear but this causes the over exposure of the background where the light is strong Wide Dynamic Range WDR The wide dynamic range WDR function helps the camera provide clear images even under back light circumstances When there are both very bright and very dark areas simultaneously in the field of view WDR balances the brightness level of the whole image and provide clear images with details E Hikvision Digital Technology Co Ltd All Rights Reserved User Manual of IR Speed Dome White Balance WB White balance can remove the unrealistic color casts White balance is the white rendition function of the camera to adjust the color temperature according to the environment automatically Patrol A patrol is a memorized series of pre defined preset function The scanning speed between two presets and the dwell time at the preset are programmable Pattern A pattern is a memorized series of pan tilt zoom and preset functions By default the focus and iris are in auto status during the pattern is being memorized Power Off Memory The dome supports the power off memory capability with the predefined resume time It allows the dome to resume its previous position after power is restored Time Task A time task is a preconfigured action that can be performed automatically at a specific date and time
35. l lead to some problems such as signal reflection anti jamming ability decline when the devices are E Hikvision Digital Technology Co Ltd All Rights Reserved User Manual of IR Speed Dome faraway At this time the dome will be uncontrollable or self running etc For such case the best way is adding a RS485 distributor This product can effectively change the star shape connection to which satisfies the requirement of RS485 industry standard in order to l 32 ER 15 Figure A 4 Star Shape Connection avoid those problems and improve the communication reliability Show as figure 5 i 120Q I 120Q r 120Q 16 Figure A 5 RS485 Distributor Troubleshooting of RS485 communication Problem Possible Reasons To Solve the Problem 1 Adjust the address and 1 The address or baudrate of the J baudrate of the remote control The speed speed dome does not match with E device to match with those of the dome does those of remote control device ih speed dome e 2 The wire RS485 connects to self test 2 Connect the wire RS485 to the the interface RS485 and wire i i action but interface RS485 and wire RS485 RS485 connects to the interface i
36. ld be 30 C 65 C outdoor speed dome and 10 C 50 C indoor speed dome To avoid heat accumulation good ventilation is required for a proper operating environment While shipping the product should be packed in its original packing Please use the provided glove when open up the product cover Do not touch the product cover with fingers directly because the acidic sweat of the fingers may erode the surface coating of the product cover Please use a soft and dry cloth when clean inside and outside surfaces of the product cover Do not use alkaline detergents Improper use or replacement of the battery may result in hazard of explosion Please use the manufacturer recommended battery type E Hikvision Digital Technology Co Ltd All Rights Reserved User Manual of IR Speed Dome Table of Contents Chapter 1 OVERVIEW weccecccct cscs cSceececcttheceactcbecstesiccuscbctecuccccdccusccetecuccelccceesccdecucedescsussccsecucccescucecccsecececcecsesccceccecesccenea 6 1 1 RS dl le WE 6 1 2 PUI CELOMS 3 eege Ee EE 6 Chapter 2 Getting Started ege ee a aa sea ceadessogsesssesesesessacseesdesesesessessescdesgdasedsecseecsed 9 2 1 Power Up le In cs sce winccsntaee credenie olbctaen stdensnvatunssn cstwedie ccunbaennsteeasavawabace cetcede ccbabden netdeadavauedseanstcesenccteedeasteoasadewsbace 9 2 2 B sic e EE TE 10 2 3 SYStEM GETINER PFESETS R AEE A E AE A A A E EI AT E AA E 10 2 4 On screen DIS Plays wwitsrteseuetioveunthivessvenvesvedh
37. mber for each patrol 6 Delete a patrol You can move the cursor to CLEAR PATH and click IRIS to delete the current patrol 7 Define the dwell time when running the fast patrol If you call the No 46 preset to enable the fast patrol the speed dome will run the patrol automatically according to the route consists of the configured preset 1 to preset 32 And you can set the Patrol_D time switches from one preset to the other 5S 10S 20S 30S and 60S are selectable 3 4 4 Configuring Patterns Purpose A pattern is a memorized repeatable series of pan tilt zoom and preset movements that can be recalled by a command or automatically performed by a configured function alarm park time task and power up Steps 1 Move the cursor to enter the PATTERNS submenu MAIN MENU gt DOME SETTINGS gt PATTERNS PATTERNS PATTERN NUM EDIT PATTERN PREVIEW CLEAR PATTERN REMAINING BACK EXIT Figure 3 15 Pattern Configuration Menu 2 Choose the pattern number Steps 1 Move the cursor to PATTERN NUM and click IRIS to enter edit mode 2 Click the up down direction buttons to select the number of the pattern which is to be configured 3 Click IRIS again to confirm the settings Note Up to 4 patterns can be configured 3 Edit the pattern E Hikvision Digital Technology Co Ltd All Rights Reserved User Manual of IR Speed Dome Steps 1 Move the cursor to EDIT PATTERN and click IRIS to enter edit mode REMAIN MEMO
38. me the same as those in the control devices The speed dome is self adaptive to the PELCO D PELCO P PRIVATE Code VICON and KALATEL 312 protocols WS Hikvision Digital Technology Co Ltd All Rights Reserved User Manual of IR Speed Dome 2 2 Basic Operations You can operate the speed dome using a control device including the control keyboard DVR DVS etc In this manual accessing the speed dome via the web browser will be taken as an example Panning and tilting Click the direction buttons to control the pan and tilt movement of the speed dome Zooming Click the ZOOM and ZOOM buttons to control the zooming Focusing Click the FOCUS and FOCUS buttons to adjust the focus Iris Click the IRIS and IRIS buttons to adjust the iris 2 3 System defined Presets Purpose The section lists the system defined presets with special functions These presets cannot be edited but can be only called through a control device e g a DVS or web browser To call the system defined presets remotely you can choose the preset number from the list in the PTZ control panel Please refer to table below for details For instance preset 99 is the Start auto scan If you call the preset 99 the speed dome starts auto scan function Table 2 2 System defined Presets Function Set manual limit stops Remote reboot Access main menu Stop scanning Start random scanning Start frame scanning Start auto scanning Start
39. n be a fire hazard When the product is installed on a wall or ceiling the device should be firmly fixed To reduce the risk of fire or electrical shock do not expose the indoor used product to rain or moisture This installation should be made by a qualified service person and should conform to all the local codes Please install blackouts equipment into the power supply circuit for convenient supply interruption If the product does not work properly please contact your dealer or the nearest service center Never attempt to disassemble the product yourself We shall not assume any responsibility for problems caused by unauthorized repair or maintenance E Hikvision Digital Technology Co Ltd All Rights Reserved User Manual of IR Speed Dome AA Make sure the power supply voltage is correct before using the product Do not drop the product or subject it to physical shock Do not install the product on vibratory surface or places Do not expose it to high electromagnetic radiating environment Do not aim the lens at the strong light such as sun or incandescent lamp The strong light can cause fatal damage to the product The sensor may be burned out by a laser beam so when any laser equipment is being used make sure that the surface of the sensor not be exposed to the laser beam Do not place the dome in extremely hot cold dusty or damp locations otherwise fire or electrical shock will occur The operating temperature shou
40. o Auto On On 5 seconds None 28 Off Off Off On Off Off Off 3 5 3 Restoring Default Camera Settings Enter MAIN MENU gt RESTORE CAMERA Click IRIS to restore the camera settings to the default value or click IRIS to exit Note Camera settings include the image parameters lens settings and display settings 3 5 4 Rebooting the Dome Enter MAIN MENU gt REBOOT DOME and click IRIS to reboot the speed dome remotely mo Hikvision Digital Technology Co Ltd All Rights Reserved User Manual of IR Speed Dome Appendix Appendix 1 Lightning amp Surge Protection This product adopts TVS plate lightning protection technology to avoid damage caused by pulse signal that is below 3000W like instantaneous lighting stroke surging etc According to the actual outdoor situation necessary protection measures must be taken besides ensuring the electrical safety The distance between signal transmission wires and High voltage equipment or high voltage cable is at least 50m Outdoor wiring should better be routed under eaves as much as possible In the open field wiring should be buried underground in sealed steel pipe and the steel pipe should be one point grounding Overhead routing method is forbidden In strong thunderstorm area or high induction voltage areas such as high voltage transformer substation high power lightning protection apparatus and lightning conductor
41. ocols without selecting protocol by DIP switch settings Keyboard Control The pan tilt movement and zoom actions of dome can be controlled by the control keyboard DVR matrix etc Scan Modes The dome provides 5 scan modes auto scan tilt scan frame scan random scan and panorama scan Preset Freezing This feature freezes the scene on the monitor when the dome is moving to a preset This allows for E Hikvision Digital Technology Co Ltd All Rights Reserved User Manual of IR Speed Dome smooth transition from one preset scene to another It also guarantees that masked area will not be revealed when the dome is moving to a preset Presets A preset is a predefined image position When the preset is called the dome will automatically move to the defined position The presets can be added modified deleted and called Label Display The on screen label of the preset title PT display zoom and time can be displayed on the monitor Auto Flips In manual tracking mode when a target object goes directly beneath the dome the video will automatically flips 180 degrees in horizontal direction to maintain continuity of tracking This function can also be realized by auto mirror image depending on different camera models Privacy Mask This function allows you to block or mask certain area of a scene for preventing the personal privacy from recording or live viewing A masked area will move with pan and tilt functions and
42. s 1 Move the cursor to enter the password modification submenu MAIN MENU gt DOME SETTINGS gt PASSWORD gt EDIT PASSWORD 2 Click IRIS to enter edit mode E Hikvision Digital Technology Co Ltd All Rights Reserved User Manual of IR Speed Dome Click the left right buttons to select the digit of the current password and click up down or FOCUS buttons to set the new value Click the right direction button to move the cursor to INPUT PW AGAIN and input the password Click IRIS to save the new settings and exit Enter the START USING submenu and switch the status to ON and click IRIS to save PASSWORD START USING INPUT PW 123456 EDIT PASSWORD INPUT PW AG 123456 DONE OPEN BACK EXIT QUIT CLOSE Figure 1 2 Set the Password 3 5 2 Restoring Default Dome Settings You can reset all dome settings to factory default parameters as shown in the table below Note Dome settings are mainly of PTZ parameters and alarm parameters and also include some system settings e g dome address Enter default dome settings menu MAIN MENU gt RESTORE DEFAUTLS Click IRIS to restore the dome settings to the default value shown as the following table or click Table 1 4 Default Dome Settings Default Value 0 2400bps Off Off HAF Max Optical Zoom High Off Day Mid Off WS Hikvision Digital Technology Co Ltd All Rights Reserved User Manual of IR Speed Dome Aut
43. s Transmission Distance When using 0 56mm 24AWG twisted pair line according to different baudrate the maximum transmission distance theory table is shown as below Table A 1 Max Distance of RS485 Transmission Baudrate Max Distance 2400BPS 1800m 4800BPS 1200m 9600BPS 800m The transmission distance will be decreased if we use the thinner cable or use this product under the strong electromagnetic interference situation or there are lots of devices are added to the bus on the contrary the transmission distance will be increased Connection Methods RS485 industry bus standard require daisy chain connection method between any devices both sides have to connect a 1200 terminal resistance show as Diagram 1 the simplified connection method is shown as diagram 2 but the distance of D should not be too long 120Q 120Q 1 2 3 4 32 Figure A 2 RS485 Connection 1 2 dl TD du wi 3 314 Figure A 3 RS485 Connection 2 Problems in the Practical Application Normally users adopt star shape connection method in construction under this situation the terminal resistors must be connected between two farthest devices as Figure 4 1 and 15 but this connection method is not satisfy the requirement of the RS485 industry standard so that it wil
44. s automatically responding to the lighting conditions It is the default mode HAUTO Half auto mode allows you to adjust the iris manually while the camera is actually adjusting the exposure automatically HAUTO mode will switch to AUTO mode automatically if there s no iris adjustment within 20 seconds or when the lighting changes in the environment IRIS User defined iris value auto shutter and auto gain It is the iris priority mode Please define the iris value according to related content in this section if you choose IRIS mode SHUTTER User defined shutter speed auto iris and auto gain It is the shutter priority mode Please define the shutter speed according to related content in this section if you choose SHUTTER mode MANUAL User defined iris gain and shutter Please define the iris value gain value and shutter speed according to related content in this section if you choose MANUAL mode Set the Iris Value The IRIS value measures the amount of light entering to the lens You can set the iris value from 0 to 17 in response to the changing light conditions Note Iris is fully closed at value O and fully open at value 17 Set the Gain 1 Gain value The value of gain indicates the amplification degree of the original image signal You can set the value from 0 to 15 2 Gain limit The higher gain value you set the more noises will appear in the image You can set the maximum user configurable gain value from O to 15 to limit
45. sccsscsescseceeeceeeceecesecaecsaecaaessaesseesaeesneseessaeeeaeceaecaaeeaaecaaecsaesseesaseeeseenes 35 3 5 3 Restoring Default Camera Settings mossing E a E aa E A A ERA ERa 36 3 3 4 Reb oting E 36 TE TE 37 Appendix 1 Lightning amp Surge Protection 37 Appendix 2 RS485 BUS COMMOCHON cecsicsccscsscrscssoscecsusntsetsectisesaesutendsinsodiaeicetnsesicacasbasentticedensuidedunsoducicasoseedsasatoescesayensdassiienna 38 Appendix 3 24VAC Wire Gauge amp Transmission Distance eeseeeccecsneceeececseeeeeeeecaeeeeeecaeseeeeecaaeeeeeecaeeeeneesaeeeeeees 41 Appendix 4 Table of Wire Gauge Standards AAA 42 mo Hikvision Digital Technology Co Ltd All Rights Reserved User Manual of IR Speed Dome Chapter 1 Overview 1 1 Description Integrated with the built in pan tilt unit the medium speed dome features highly sensitive response and reliable performance The speed dome can be adopted in various surveillance fields with its full integral functions and features such as corridor large venue meeting room station neighborhoods etc HIKVISION Figure 1 1 Appearance 1 2 Functions Note The functions vary according to the different models of the speed dome Limit Stops The dome can be programmed to move within the limit stops left right up down Self adaptive Protocol The speed dome is compatible with PELCO D PELCO P PRIVATE Code VICON and KALATEL 312 etc and is capable of being self adaptive to these prot
46. set number is displayed if the lens moves to the certain place where you ve set a preset for Zone Show Display the zone title Address Show Display the address of the speed dome Error Rate Show Display the error rate of the speed dome Fan and Heat show Display the heat information of the speed dome WS Hikvision Digital Technology Co Ltd All Rights Reserved User Manual of IR Speed Dome Chapter 3 Menu Operation Notes 1 The operation interface of the different speed domes may differ Please refer to the actual operation interface 2 You can click the left and right direction buttons in the PTZ control panel via the IE browser of the DVR to enter the next page or return to the previous page of the submenu if more than one page is available a DOME SYS INFO C VERSION _ SETTINGS SC PROTOCOL TEMPERATURE RESTORE DEFAULTS RESTORE CAMERA PATTERNS PRIVACYS MOTION PARAMETER CLEAR SETTINGS PASSWORD ZONES PRESETS LANGUAGE PATROLS LINE SYNC TIME TASK Figure 3 1 Main Menu Before you start You can operate the speed dome using the on screen display menu remotely by connecting to a DVR or a DVS encoder Examples of entering speed dome menu are listed as follows Enter the menu by pressing buttons PTZ gt REC gt 9 gt 5 on the front panel of the DVR Enter the menu by pressing buttons CALL gt 9
47. the gain range and control the noises in the image Note You need to change the IRCUT FILTER as DAY or NIGHT mode and set the AE MODE as MANUAL before you adjust the gain value Set the Shutter Purpose The speed of the electronic shutter controls the amount of light entering to the lens in a unit of time a second You can manually configure the shutter speed for the speed dome and you can also enable the slow shutter function for low lighting circumstances 1 Shutter speed The larger you set the SHUTTER value the faster the shutter speed is the fewer the amount of entering light per second is and the darker the image is You can set the value as 1 2 4 8 15 30 50 125 180 250 500 1000 2000 4000 or 10000 Note The value of X indicates that the shutter speed is 1 X second If you set the SHUTTER value bigger shutter speed is faster the amount of entering light per second is fewer and E Hikvision Digital Technology Co Ltd All Rights Reserved User Manual of IR Speed Dome the image is darker 2 Slow shutter Set SLOW SHUTTER as ON the shutter speed can automatically slow down to extend exposure time under low lighting circumstances to obtain clearer image Task 7 Configure exposure compensation You can set the EXPOSURE COMP value from 0 to 14 The default value is 7 You can adjust this value to increase the brightness of the image Task 8 Configure white balance You can set WHITE BALANCE mode as A
48. tilt scanning Start panorama scanning Patrol 5 Patrol 6 Patrol 7 Patrol 8 Function Auto flip Return to home position Patrol 1 Patrol 2 Patrol 3 Patrol 4 IR cut filter in IR cut filter out Pattern 1 Pattern 2 Pattern 3 Pattern 4 Enable fast patrol Enable limit stops mo Hikvision Digital Technology Co Ltd All Rights Reserved User Manual of IR Speed Dome Note For Manchester code control protocol the system defined presets with special functions are shown as below Table 1 1 System defined Presets of Manchester Code Control Protocol Function Function Remote reboot Access main menu Stop recording pattern Record Pattern 1 Record Pattern 2 Record Pattern 3 Auto flip Run Pattern 1 Run Pattern 2 Run Pattern 3 2 4 On screen Displays The speed dome supports following on screen displays Zoom Show Identifies the amount of magnification The format is ZXXX XXX is the zoom amount PT Show Displays panning and tilting direction with the format of NEXXX TXXX The NE followed with XXX indicates the degrees in north east direction while the T followed with XXX indicates the degrees in tilt position Time Show Displayed as Day Month Year Day of Week Hour Minute It supports 24 hour time system Preset Show After you call the configured preset the pre
49. to enter the edit mode 2 Click the up and down buttons to select the zone number to be configured 3 Click IRIS again to confirm the settings and exit edit mode of this column Note Up to 8 zones can be configured 3 Configure the zone area E Hikvision Digital Technology Co Ltd All Rights Reserved User Manual of IR Speed Dome Steps 1 Move the cursor to EDIT ZONE and click IRIS button to enter the edit mode 2 You can see SET LEFT LIMIT on the screen Click the direction buttons to set the left limit stop 3 Follow the prompts on the screen to set the right limit up limit and down limit 4 Click IRIS button to save the settings and exit 4 Set the zone status and scan status ZONE STATUS The zone status just indicates the current status of the zone SCAN STATUS You can set the scan status to ON OFF to enable disable the scanning in the zone Note ZONE STATUS is not editable After you edited the zone it will switch to ON automatically if you delete the zone the ZONE STATUS will switch to OFF 5 Clear the zone settings Move the cursor to CLEAR ZONE click IRIS to clear all the settings of the current zone and click IRIS again to confirm the settings and exit 3 4 7 Clearing PTZ Control Settings Purpose You can clear all user defined PTZ control settings including presets patrols patterns zones and time tasks You can also clear privacy masks on this menu Steps 1 Enter the CLEAR SETTINGS menu

User manual of DS-2AE7164

Contents

Download Pdf Manuals

Related Search

Related Contents