Manual - BZB Express
Contents
1. DVI to HD SDI Single Link Scaler USER MANUAL e www gefen com ASKING FOR ASSISTANCE Technical Support Telephone 818 884 6294 800 545 6900 Fax 818 884 3108 Technical Support Hours 8 00 AM to 5 00 PM Monday through Friday Write To Gefen Inc C O Customer Service 6265 Variel Ave Woodland Hills CA 91367 9897 Notice Gefen Inc reserves the right to make changes in the hardware packaging and any accompanying documentation without prior written notice The DVI to HD SDI Single Scaler Scaler is a trademark of Gefen Inc O 2007 Gefen Inc All Rights Reserved 10 TABLE OF CONTENTS Introduction Operation Notes Panel Descriptions Menu Functions Supported Input Output Resolutions RMT 8HDS IR Installation Firmware Update Procedure Specifications Warranty INTRODUCTION Gefen s DVI to HD SDI Single Link Scaler is the newest revision of our HDSDI conversion line incorporating full single link DVI D conversion scaled upto SD HDSDI single resolutions Resolutions of up to 1080p are supported over the HDSDI link for those that want true High Definition Performance has been greatly enhanced due to Gennum s VXP Scaler onboard allowing for new features such as Color amp Gamma Correction Noise Reduction Detail Enhancement Aspect Ratio Selection Pattern Generator Mode amp Multiple Language Menu Support Bottom Line More performance less cost HOW IT WORKS DVI devices2. are connected to the DVI input and SDI devices are connected to the SDI output When the source display and the Scaler are powered and connected video signals are converted to the proper format CONTENTS The DVI to HD SDI Scaler SL package consists of 1 DVI to HD SDI SL Scaler 1 6 foot DVI Cable m m 1 RMT 8HDS IR Remote Control 1 5V DC Power Supply 1 User s Manual OPERATION NOTES On power up the DVI to HD SDI Scaler will automatically detect the input format of the input The unit is controlled using the included remote The following are the buttons for the RMT 8HDS IR UP Navigates cursor up LEFT Navigates cursor left Enter Accept Operation Return to Menu RIGHT Navigates cursor right DOWN Navigates cursor down MENU Show Hide Onscreen Display OUTPUT Change Output Format SOURCE Non operational To bring up the onscreen menu press the MENU button Navigation is done using But tons up left right and down Push the Enter button to accept the cursor focus Pressing the Output button cycles through the following output modes 480i 576i 720p 1080i Other functions and output modes can be accessed through the onscreen menu To Restore I O settings simply recycle power on the Scaler Note Both dip switches under the remote battery cover must initially be in the OFF position to communicate with the Scaler Gefen Remote RMT SHDS IR PANEL DESCRI
3. 48x1080 Maxim m OUEST E 2048x1080p24 EE DVI I 29 pin female digital only Ee q g c e o Aee Ra RAD RR TETE BNC female Deeg DS RR RAR ee oe Serial RS 232 Power geegent eege DV DC Power EE e 20 watts Max Dimensions PR RS esses ania RR 6 5 W x 1 H x 6 75 H SNIPP 6 EE 5 Ibs WARRANTY Gefen Inc warrants the equipment it manufactures to be free from defects in material and workmanship If equipment fails because of such defects and Gefen Inc is notified within two 2 year from the date of shipment Gefen Inc will at its option repair or replace the equipment provided that the equipment has not been subjected to mechanical electrical or other abuse or modifications Equipment that fails under conditions other than those covered will be repaired at the current price of parts and labor in effect at the time of repair Such repairs are warranted for ninety 90 days from the day of reshipment to the Buyer This warranty is in lieu of all other warranties expressed or implied including without limitation any implied warranty or merchantability or fitness for any particular purpose all of which are expressly disclaimed 1 Proof of sale may be required in order to claim warranty 2 Customers outside the US are responsible for shipping charges to and from Gefen 3 Copper cables are limited to a 30 day warranty and cable must be free from any scratches markings and neatly coiled The information in this manual has b
4. PTIONS DVI HDSDI Infrared Eye Power Indicator Light DVI D Input Connector Uplink Port Output 5V Power RS 232 HD SDI Menu Functions Aspect Full Screen Stretches input to fill the Monitor Letter Pillar Box Sets the aspect ratio to fit a letter or pillar box format Panoramic Panoramic Zoom feature Extract Feature to magnify the signal Extract Size Adjusts signal magnification Horizontal Vertical Position Moves the magnified signal Horizontally and Vertically Through Feature to crop the signal Horizontal Vertical Size Horizontally and Vertically contracts or expands the cropping viewport Horizontal Vertical Position Move the signal Horizontally or Vertically inside the cropping viewport Layout Feature to Resize Image resolution Size and Position Horizontal Vertical Size Adjust Horizontal or Vertical resolution Horizontal Vertical Position Move image Horizontally or Vertically Picture Image Color Contrast Individually adjust the contrast for red green and blue Brightness Individually adjust the brightness for red green and blue Black level Adjust black levels between 0 default and 100 Detail Enhancement Detail Enhancement Digitally enhance signal Noise Threshold Adjusts noise allowed in detail enhancement Noise Reduction Digitially reduce signal noise Motion Threshold Menu Functions continued Input Input Video Format Auto Dete
5. ct by default Signal can be forced to a specific High definition resolution Please see Supported Input Output Resolutions for more information Input Graphic Format Auto Detect by default Signal can be forced to a specific computer resolution Please see Supported Input Output Resolutions for more information Clean Aperture Horizontal and Vertical Size Stretch image Horizontally or Vertically Horizontal and Vertical Position Move image in view port Horizontally or Vertically Remote Channel Changes the IR code of the DVI to HDSDI Scaler to one of 4 different settings between 0 and 3 When the remote channel is changed dip switches in the remote must be changed to the corresponding code in order to continue operating the DVI to HDSDI Scaler Please see RMT 8HDS IR Installation page for more information Output Output Format Select the desired output resolution Please see Supported Input Output Resolutions for more information Genlock Reference Locks input clock in sync with output clock Note feature only works if input and output frequencies are multiples of each other Language Set menu to display English or French text Gamma Correction Default Set for Default Gamma settings sRGB Custom Enables Gamma Coefficient menu item as the current Gamma coefficient Gamma Coefficient 0 3 3 0 Default set at 1 0 Patterns Color Bars Display color bar video pattern Cross Hatch D
6. een carefully checked and is believed to be accurate However Gefen Inc assumes no responsibility for any inaccuracies that may be contained in this manual In no event will Gefen Inc be liable for direct indirect special incidental or consequential damages resulting from any defect or omission in this manual even if advised of the possibility of such damages The technical information contained herein regarding EXT DVI 2 HDSDISSL features and specifications is subject to change without notice 10 ma DVI 2 HDSDI ssl 6265 Variel Avenue Woodland Hills CA 91 1 800 545 6900 818 884 6294 fax 818 88 www gefen com gsinfo gefen com 3 a 67 3108
7. isplay cross hatch video pattern SUPPORTED INPUT OUTPUT RESOLUTIONS Input Video Formats Supported Output video formats supported moso Der o SSS moso oos Il mossa fioo mowo foom RMT 8HDS IR Installation 1 Remove battery cover from the back of the RMT 8HDS IR remote 2 Verify that dip switches 1 amp 2 are in the down OFF position 3 Insert the battery hold the battery so that you can see the positive side facing up The side that is not marked must be facing down 4 Test the RMT 8HDS IR remote by pressing ONLY one button at a time The indica tor light on the remote will flash once each time you press a button WARNING Do not press multiple buttons simultaneously and do NOT press buttons rapidly These actions will cause the remote to reset and steps 1 4 will have to be repeated Note The RMT 8HDS IR ships with two batteries One battery is required for operation the second battery is complimentary The following are the dip switch combinations that correspond to the Remote Code menu option on the DVI to HDSDI Scaler Please see Menu Functions section for more information Remote Channel 0 Remote Channel 1 Remote Channel 2 Remote Channel 3 FIRMWARE UPDATE PROCEDURE Please check http www gefen com kvm support download jsp for firmware updates and procedures SPECIFICATIONS af ele Ee le e GE 1 65 Gbps Ou tp t ISO le le q PRANTO 1 485 Gbps Maximum MU FS SOMO MON E 20
Download Pdf Manuals
Related Search