User manual
Contents
1. 1024X768 1024X768 1024X768 1280X1024 1280X1024 1152X864 1280X960 1440X900 1440X900 1680X1050 1680X1050 VGA only 1280X768 1920X1080 H Freguency khz 31 47 31 47 35 00 37 86 37 50 35 16 37 88 48 08 46 88 49 72 48 36 56 48 60 02 64 00 80 00 67 50 60 00 56 00 70 60 65 20 82 30 47 776 67 50 V Frequency hz 70 60 66 72 75 56 60 72 75 75 60 70 75 60 75 75 60 60 75 60 75 60 60 Touch Screen Driver Installation The PT2245PW is available with USB connection The touch driver is available for these operating systems Windows 7 VISTA 64 32 bits XP 2000 XP Embedded Express only Linux Apple Mac OS Please Note 1 The PT2245PW is Microsoft Windows HID Human Interface Device compatible if you use the USB touch screen interface No additional software driver is reguired for general operation of the touch screen 2 For PT2245PW the system requires 15 seconds for Windows 7 to install uninstall the touch driver while turning power on off or plugging unplugging USB cable PT2245PW Calibration Instruction Calibrating the touch screen in Windows 7 1 2 3 Tap the Start button Control Panel and then Hardware and Sound Under Tablet PC Settings tap Calibrate the screen for pen or touch input On the Display tab under Display options tap Calibrate and then Yes to allow the program to make changes Follow the on screen i2. Notice To ensure the display works well with your computer please configure the display mode of your graphics card to make it less than or equal to 1920 x 1080 resolution and make sure the timing of the display mode is compatible with the LCD display We have listed the compatible Video Modes of your LCD display in the appendix on page 16 for your reference Applicable external power supply Lite On PA 1051 0 Figure 8 1 User Controls Side Panel Controls Key Name MENU Menu A Up v Down SELECT Select 0 Power Menu disappear return to main item Brightness Main item select up Adjust up Main item select down Adjust down Select sub item function Power On Off How to Use the OSD Menus Key Name MENU Menu A U v Down SELECT Select 0 Power alerg _ Press the Menu button to pop up the on screen menu and press Up or Down button to select among the five functions in the main menu 2 Choose the adjustment items by pressing the Select button Adjust the value of the adjustment items by pressing the Up or Down button 4 With the OSD menu on the screen press the Menu button to return
3. PLANAR PT2245PW Touch Screen Edge Lit LED LCD Monitor USER S GUIDE www planar com The information contained in this document is subject to change without notice This document contains proprietary information that is protected by copyright All rights are reserved No part of this document may be reproduced translated to another language or stored in a retrieval system or transmitted by any means electronic mechanical photocopying recording or otherwise without prior written permission Windows is a registered trademark of Microsoft Inc Other brand or product names are trademarks of their respective holders The test results show that this device meets the FCC rules Those limits are set to protect residential areas from the devices with harmful emission This device will produce use and radiate radio freguency energy In addition failure to follow the user s manual to install or use this device might produce harmful interference with radio communication Not withstanding the foregoing it does not guarantee that this type of harmful interference does not occur in some special installations The interference caused by this device to the reception of radio or television signals may be verified by turning it on and off Any changes or modifications to this TFT LCD would void the user s authority to operate this device For more information on how to recycle your product please visit WWW PLANARSYSTEMS COM GREEN Table of Conte
4. ect to change without notice 020 1224 00A
5. ected as described in the Installation section gt Make sure the pins of the connectors are not crooked or broken Problem Partial Image or incorrectly displayed image gt Check to see if the resolution of your computer is higher than that of the display gt Reconfigure the resolution of your computer to make it less than or equal to 1920 x 1080 Problem Image has vertical flickering line bars gt Use Horizontal size to make an adjustment gt Check and reconfigure the display mode of the vertical refresh rate of your graphic card to make it compatible with the display Problem Image is unstable and flickering Use Fine to make an adjustment Problem Image is scrolling gt Check and make sure the VGA signal cable or adapter is securely connected gt Check and reconfigure the display mode of the vertical refresh rate of your graphics card to make it compatible with the display Problem Vague image characters and graphics gt Use Horizontal size to make an adjustment If this problem still exists use Fine to make an adjustment Warning Signal If you see warning messages on your screen this means that the display cannot receive a clean signal from the computer graphics card Below are the three kinds of Warning Signal Please check the cable connections or contact your local dealer or our service center for more information No Signal This message means that the display has been po
6. en the back cover surface and the bottom of the screw hole is 8 mm Please use four M4 screws diameter with proper length to mount your monitor Please note the mounting stand must be able to support at least 17 6 Ibs 8Kg Start Your Installation Please follow these instructions so that you can hook up the cables to associated connectors Lay the display flat on an even surface Move the stand into position as seen in the step 1 diagram Remove the cable cover as seen in the step 2 diagram Connect the cables to the appropriate connectors as seen in the step 3 diagram Re attach the cable cover Take the screw CBM M3x6 out of the accessory box and insert the screw into the cable cover and monitor as seen in the step 4 diagram Te ey Connecting the Display Figure 8 1 To setup this display please refer to the following figure and procedures 1 2 Be sure all equipment is turned off Connect the DC plug to the power connector on the monitor and the other end into an electrical outlet 8 1 Connect the D SUB or DVI cable from the display s D SUB or DVI input connector to the D SUB or DVI connector of your host computer and tighten the screws 8 1 Connect the USB cable from the USB port of your display to the USB port 8 1 of your computer Configure the touch screen Refer to the Touch Screen Driver Installation section on page 17 Once the touch screen is configured the monitor is ready for use A
7. manual to maximize the life of your unit Do Turn off the product before cleaning Touch screen surface may be cleaned using a soft clean cloth moistened with mild window glass commercial cleaners or 50 50 mixture of water and isopropyl alcohol Use a soft cloth moistened with mild detergent to clean the display housing Use only high quality and safety approved DC adapter e Disconnect the power plug from outlet if the product is not going to be used for an extended period of time Don t Do not touch the Display screen surface with sharp or hard objects Do not use abrasive cleaners waxes or solvents for your cleaning Do not operate the product under the following conditions Extremely hot cold or humid environment Areas susceptible to excessive dust and dirt Near any appliance generating a strong magnetic field In direct sunlight Introduction About PT2245PW Series The PT2245PW Series is a 21 5 flat panel screen with an active matrix thin film transistor TFT edge lit LED LCD This unit is to be used as commercial and light industrial eguipment only Features include Direct Analog signal input Direct Digital signal input Active matrix TFT LCD technology 1920 x 1080 resolution 21 5 viewable display area 16 9 aspect ratio 31 47 82 3 KHz horizontal scan 56 75 Hz high refresh rate 0 24795mm x 0 24795mm pixel pitch Auto adjustment function Multilingual OSD user control 100
8. mm VESA mount Removable base for flexible mounting solutions Touch screen with USB controller Touch Screen for PT2245PW Projected Capacitive touch screen for finger input only Surface Glare treatment Interface USB controller Transmittance 90 5 HID Windows 7 Driver VISTA XP 2000 CE XP Embedded Linux Apple Mac OS Package Overview Power Cord VGA Signal Cable USB Cable A to B DVI D Cable PLANAR USERS GYD PLANAR auch User s Guide Landing Strip Cable Cover Screw Installation Product Overview Front View e Bottom View Without Stand o o EE 00000890 oF EZ o BE VGA RJ Type o ae T oje lal gt g ora 5000000 DVI DC IN USB VESA Mount for Your Monitor This monitor conforms to the VESA Flat Panel Mounting Physical Mounting Interface standard which defines a physical mounting interface for flat panel monitors and corresponding with the standards of flat panel monitor mounting devices such as wall and table arms The VESA mounting interface is located on the back of your monitor To mount the monitor on a UL certified swing arm or other mounting fixture follow the instructions included with the mounting fixture to be used Slots X6 VESA Mounting Interface 100 0 mm A Warning Please select the proper screws The distance betwe
9. n is selected this indicates that all the buttons except the power button are now disabled b When the Power Lock function is selected the Power key is disabled The user cannot turn off the monitor with the Power key AW On Screen Display Menus Main OSD Menu ITEM Contrast Brightness Auto Adjust Left Right Up Down Horizontal size Fine OSD Left Right OSD Up Down OSD Time out OSD Language Factory Reset RGB CONTENT The monitor luminance level control The monitor backlight level control Fine tune the image to full screen automatically Moving screen image horizontal position to left or right Moving screen image vertical position to up or down The screen image horizontal dot clock adjustment The screen image pixel phase adjustment Moving OSD menu horizontal position to left or right Moving OSD menu vertical position to up or down OSD auto disappear time selection OSD menu language selection English French Japanese Deutsch Spanish Italian Traditional Chinese and Simplified Chinese Factory default value restored Color temperature selection 9300K 6500K 5500K 7500K User Appendix Troubleshooting If you are experiencing trouble with the display refer to the following If the problem persists please contact your local dealer or our service center Problem No image appears on screen gt Check that all the I O and power connectors are correctly and well conn
10. nstructions to calibrate the touch screen Y S eGalaxTuner Release Shortcut FS test 4 Getting Started D t Windows Media Center Pictures Calculator Music Sticky Notes Games QR Snipping Tool Computer a Remote Desktop Connection j Control Panel Solitaire gaw M BES Devices and Printers ey Magnifier Default Programs is Microsoft Surface Collage Help and Support gt All Programs ut down De Adjust your computer s settings System and Security User Accounts and Family Safety Review your computer s status 7 Add or remove user accounts Back up your computer 4 Set up parental controls for any user Find and fix problems Appearance and Personalization Network and Internet Change the theme View network status and tasks Change desktop background grourand sharing op Adjust screen resolution Hardware and Sound Clock Language and Region View devices and printers Change keyboards or other input methods Hardware and Sound Add a device splay Add or remove printe d other hardywa Je system sounds Ease of Access play CDs automatically conserve Uninstall a program power update device drivers and WY more Let Windows suggest settings Optimize visual display Devices and Printers Add a device Add a printer Device Manager AutoPlay Change default settings for media or devices Play CDs or other media automatically Sound Adjust system volume Change s
11. nts Usage Notice PIE AMON SE tone 1 Introduction About PT 224 5PW Sele Srana a a aa 2 TouchScreen Tor PTZ2245P W veces a a E a aie oc ec qe nie 2 P kage OVE NEN renni onore EE N teen RM Tele 3 Installation Product Overvie ccc ceccececeeececeeeeeeeececeeeaeeeeeeeeeeaeeeeneeaeesaeeneeateeaeeeeaeeeatneueeeentaneeeennes 4 Font MCV island 4 Bottom View yy OUT Stand nement 4 VESA Mount for Your Monitor eee P K K K P P P K K hn 5 Start 0 LE 1 ASS LE VELO DE aula aaea oa 6 Connecting the Display Figure 8 1 J r Fig re AS NEA S ERA EEEE A 8 User Controls Side a A EA ai 9 Howto Use the OSD e oo 10 OFS Display MBS gosta indemne 11 Appendix FOUT S00 IP lens een aa ce nounou 12 EY Tae are SNA PE D PE E OL RO MOR PE O RE 13 N S jo izk a EA 13 Gong 13 LOT Matane dodo 13 Product DIMENSIONS creiran rae aa aaa ada ud nie 14 Compatibility Mode 2 osa 16 Touch Screen Driver INstalatioR asero de ka iesanauimaceadtematieae ska 17 P12245PW Calibration INSthUCU OM zz ssszss aaa O dernede 18 PT2245PW Install INStrUCU ON dn Ek Eee s rop ac ini en 20 Technica SUPPOSE en tre bibi eine 21 Usage Notice VAN Warning To prevent the risk of fire or shock hazards do not expose this product to rain or moisture VAN Warning Please do not open or disassemble the product as this may cause electric shock Precautions Follow all warnings precautions and maintenance as recommended in this user s
12. to the main menu or to exit OSD 5 The OSD menu will automatically close if you have left it idle for a pre set time 6 To Lock the OSD Power menu buttons please follow the instructions below Please note the monitor has to be turned ON with a valid signal pre set a Press the Menu key the OSD menu will open b Press and hold the Menu key again with the OSD menu on the screen the OSD menu will disappear Then press the Power key 1 time while the menu key is still being pressed The Lock Unlock menu will appear for 3 seconds c Use the Select key to select OSD or Power setting then set at Lock by pushing the UP or Down button d When the UP or Down button is released the previous setting will be saved and exit the Lock Unlock menu automatically 7 To Unlock the OSD Power menu buttons please follow the instructions below Please note the monitor has to be turned ON with a valid signal pre set a Press and hold the Menu key then press the Power key simultaneously the Lock Unlock menu will appear for 3 seconds b Use the Select key to select OSD or Power setting then set at Unlock by pushing the UP or Down button c When the Up or Down button is released the previous setting will be saved and the Lock Unlock menu will close automatically Please note a When the OSD Lock functio
13. wered on but it cannot receive any signal from the computer graphics card Check all the power switches power cables and VGA DVI signal cable Going to Sleep The display is under the power saving mode In addition the display will enter power saving mode when experiencing a sudden signal disconnecting problem The monitor can be activated by pressing any keyboard triggering the mouse or touching the screen Out of Range This message means that the signal of the computer graphic card is not compatible with the display When the signal is not included in the Video Modes list we have listed in the Appendices of this manual the monitor will display this message Product Dimensions 517 4 mm gt Front View E E El E eo nm o 8 S J 46 0 mm Side View E o N N 249 6 mm gt Top View 219 0 mm Rotate 7 313 3 mm z gt Front View E E E 5 x 46 0 mm gt Side View i E E 249 6 mm gt Top View Compatibility Modes Mode IBM VGA IBM VGA Apple Macil VESA VGA VESA VGA VESA SVGA VESA SVGA VESA SVGA VESA SVGA Apple Mac VESA XGA VESA XGA VESA XGA VESA SXGA VESA SXGA VESA SXGA VESA SXGA WXGA WXGA WSXGA WSXGA VESA WXGA WSXGA Resolution 720X400 640X480 640X480 640X480 640X480 800X600 800X600 800X600 800X600 832X624
14. ws If you are using a PC running Linux or Apple Mac OS follow the instructions below 1 Power on the computer 2 Make sure that the USB cable is connected to the computer 3 Download the driver online at www planar com support and execute 4 Follow the step by step instructions found in the folder file of the driver Technical Support Cables and Accessories To find cables and accessories for your Planar monitor touch screen or other Planar products visit our online store at www PlanarOnline com Technical Support Visit Planar at http www planar com support for operations manuals touchscreen drivers warranty information and access to Planar s Technical Library for online trouble shooting To speak with Planar Customer Support please have you model and serial number available and dial Planar Support Tel 1 866 PLANAR1 866 752 6271 or 1 503 748 5799 outside the US Hours 24 hours a day 7 days a week Toll or long distance charges may apply Planar Systems Inc Customer Service 24x7 Online Technical Support http www planar com support 1195 NW Compton Drive Beaverton OR 97006 1992 Tel 1 866 PLANAR1 866 752 6271 or 1 503 748 5799 outside the United States Hours 24 hours a day 7 days a week 2013 Planar Systems Inc 3 13 Planar is a registered trademark of Planar Systems Inc Other brands and names are the property of their respective owners Technical information in this document is subj
15. ystem sounds Manage audio devices Power Options Change power saving settings Change what the power buttons do Require a password when the computer wakes Change when the computer sleeps Choose a power p Display Make text and other items larger or smaller Adjust screen resolution Connect to an external display How to correct monitor flicker refresh rate Pen and Touch Change settings for handwriting personalization Turn flicks on and off Configure your pen and touch displays Display options Display Details Touch Input Available Choose the order im W your screen rotates r PT2245PW Install Instruction If you are using a PC running Windows 7 VISTA XP 2000 follow the instructions below 1 Power on the PC 2 Be sure the USB cable is connected from the PC to the display 3 Download the driver online www planar com support and execute 4 Follow the step by step instructions as shown on the pop up windows If you are using a PC running Windows XP Embedded follow the instructions below Express 1 Power on the computer 2 Make sure that the USB cable is connected to the computer 3 Be sure that your EWF is disabled If your EWF is enabled please disable the EWF by using the EWF Manager command 4 Once the EWF is disabled download the driver online and execute 5 Click on the XP driver at www planar com support and follow the step by step instructions as shown on the pop up windo
Download Pdf Manuals
Related Search