WT-1010SA - SMARTO Group
Contents
1. 4 Default 1 Adjust the speaker and microphone volume to compatible with your alarm panel Inquire the Software and Hardware Version of WT 1010SA via Voice To check the software and hardware version of WT 1010SA unit you can press 13 to proceed HW l lver SW 4 7 ver MW 1 3ver The information will be displayed on screen Press to turn back WT1010SA USER MANUAL Rev 1 5 Technical Support Technical witura com COPYRIGHT 2009 WITURA CORPORATION SDN BHD WT 10105A USER MANUAL Inquire All Programmed Administrator Number via SMS To inquire all the programmed administrator number you can send the following SMS command to the unit Text Command ADM Example of Return Message 1 13256997049 2 15915325252 3 13456679988 are ae as Checking the Signal Strength via SMS To check the signal strength of the unit you can send the following SMS command to the unit Text Command CSQ Example of Return Message CSQ lt 28 gt Checking the Current Time Status via SMS To check the current time you can send the following SMS command to the unit Text Command ASTM Example of Return Message TIME 01 35 50 WT1010SA USER MANUAL Rev 1 5 Technical Support Technical witura com COPYRIGHT 2009 WITURA CORPORATION SDN BHD Changing the Programming Mode Password via SMS It is possible to change the login password by sending the following SMS command T2. WT 10108SA STAND ALONE GSM ALARM SYSTEM User Manual da UNTURA Wie WITURA CORPORATION SDN BHD N 10SA USER MANUA Sketch of the WT 1010SA LCD Display Display Signal Strength Programming Status and etc SIM Card Holder Insert SIM here evceeeeerarr era eaceaeecearer PTTL GSM Module GSM Transmission Antenna Connector Block The antenna must be All wiring must be connected well connected before here turn on the terminal Lithium Ion Battery Back up when Power Failure e e e e e e Main Unit Wiring Diagram 7 a 11 12 13 14 15 16 17 13 E E MN EW E 535 3 F E E 12 DC Em Ai ty ETUNA Auxiliary 5 SPK PSTN Failu WT1010SA USER MANUAL Rev 1 5 Technical Support Technical witura com COPYRIGHT 2009 WITURA CORPORATION SDN BHD Please check the following packing list Name Quantity Unit WT 1010SA Main Unit Telephone line Power adapter Lithium Ion Back up Battery 5m GSM terminal antenna User s Manual 1 Introduction to WT 1010SA GSM Alarm SysteM ocmincnenenenenincarmememama ren Z Main Features of the Wi lLOLOS Asian 3 Installation INS UPUICUION ci ir vcs A dE E a wi nd aaa a e Ao te set set set set set A ooo e 3 2 WT 1010SA Inputs Outputs Wiring INStrUCtiONS omcucuocnoneninenonomenenincmemenemencnimimenemememimcmimememeas 3 3 miele i the SIM Cardinaiasiiani is
3. 34 ROWer up the WITO0TOS Acs antaras dc eee 3 5 Dialing a number from the attached telephone St ncucncnincncnimemen noninimemenencnrmema maneras 4 WT 1010SA Configuration Instructions Via VOICE cmcmcucnininenenenenenenenenenenenemenememememamss 4 1 WANN UG IA A ccheetc ascertain sche avatar everett O A A A Oo MwA NDA DWN su hb hh jp O O O Stepl Enter Programming ModE ss ermarsasns aAA A ARAA EAR Step2 Reset the WI 10105A UE critico datan T a a E a cti Step3 Programming the Administrator NUMbDeT ocmcccncncncnimenomenencnimenomememrrme meme bb Ba B N e FR Step4 Setting the Recipient that will receive Alert MessagesS s m m m usum emess sunm remem nurum rmrrmeumrmemns E N Step5 Programming the Area LOdBuesccuisensci clarins lc E UJ Step6 Setting the Function of Adding Area Code when Transmitting an AlarM m m ememememememenenens E UJ Step7 Setting the Delay Time for Transmitting a Dialing NUMbeErTf m s m m memssmsmrmememememrmrmememrmrmrms E IS Step8 Setting for calling a group of Administrator NUMDETLS 0 cases en ew enews ntmewenennrnemenemenenen Step setHng TOR AUTO POSE as Steplo Seting Tor SUN Falles a eae ete te ee te ie Step l Setting Tor AC Palla sicario N hh Be Be O O O A Step12 Setting for Overcoming GSM Jammers GSM Tower FailUre n muum nanm em omom emememrmememememene N N se a o A E A E EE A ne T ere ree N UJ step14 Arm and Disarm The
4. Alarm siren connected to PIN6 PIN7 will sound when jammer is detected 12 4 Setting the Parameter for GSM Tower Failure To set the parameter you can press 41 to proceed NETDT2 RLY 2 NETDT2 06 RLY2 10 Example To set the network failure time for 6 seconds and the turn on time of Relay 2 for 10 seconds Simply press 0610 WT1010SA USER MANUAL Rev 1 5 Technical Support Technicalowitura com COPYRIGHT 2009 WI TURA CORPORATION SDN BHD Y NIOSA UL 2 MANUA NETDT2 06 RLY2 10 OK Description NETDT2 stands for network failure time range from 00 59 seconds Default 6 seconds RLY2 stands for turn on time of Relay 2 when network fails 00 59 seconds 00 means RLY2 will stay ON permanently Step 13 Input Settings 13 1 Turn on the function of Inputs To turn on the function of input number 1 you can press 24 to proceed IN1 OP 1 CL 1 AL 1 CA1 1 CA2 1 Example Setting the input 1 to generate an SMS call the administrators and sound the audible alarm when it triggered Simply input 11111 IN1 OP 1 CL 1 AL 1 CA1 1 CA2 1 OK Description OP stands for generation of SMS when input triggered Open Default 0 CL stands for generation of SMS when input triggered Close Default 0 AL stands for sounding the audible alarm when input triggered Default 0 CA1 stands for calling the administrators when input triggered o
5. This can be done by placing it in an unlocked Mobile phone and first checking if the SIM requested any PIN code If this is the case the PIN code can be disabled using the security settings on the phone Warning The WT 1010SA identifies only 3V SIM Card lill 919 TEN Proceed as follows 1 Slide back the SIM door and lift it up 2 Slide the SIM card into the SIM door making sure that the clipped corner of the SIM card lines up with the clipped corner of the SIM holder 3 Close the SIM door 4 Slide the SIM door to lock the SIM card in place 3 4 Power up the WT 1010SA When power up the WT 1010SA it will display as below LOADING gt gt gt gt gt WAITING When the terminal is ready to use it will display as below C Signal Yl WT 1010 Note Whenever the WT 1010SA fails to logon to network or fails to detect the SIM card it will restart automatically until it has detected the SIM card or successfully logon to network WT1010SA USER MANUAL Rev 1 5 Technical Support Technical witura com COPYRIGHT 2009 WITURA CORPORATION SDN BHD 3 5 Dialing a number from the attached telephone set Single Line Phone Connect to Phone Port After the GSM module is connected to the GSM network an attached fixed line phone can be used to make calls If you pick up the phone you will hear a dial tone Simply dial the number you want to call as if you are dialing from a normal fixed line phone You can also
6. a SMS or phone call with a certain command For example SMS Call in to switch on lighting air conditional generator sensor or other equipment Automatically call to 8 pre program phone numbers while alarming The WT 10105A also will SMS to 8 programmable phone number to notify the user if any intruder Open your auto gate with your basic telephone Connect the WT 1010SA with the auto gate and your house basic telephone Besides you can use the WT 1010SA as your house telephone you also can open your auto gate by pressing a command at the basic telephone WT1010SA USER MANUAL Rev 1 5 Technical Support Technical witura com COPYRIGHT 2009 WITURA CORPORATION SDN BHD 10 11 12 Most of the countries GSM Mobile operator offer cheaper call plan compared to telecom landline It can connect to the basic telephone to make call and if any intruder the WT 1010SA will cut the telephone call and send the alarm messages first In order to prevent professional thief to disconnect GSM by using GSM Jammer the WT 1010SA will transmit the alarm if signal drop immediately and trigger the siren The owner will automatically received the SMS text messages for AC Fail Input 1 Input 4 Fail GSM Alive if any of the above having problem Auto test reporting system after the owner program the reporting time the WT 1010SA will dial the programmable number to inform that GSM Alive This is to make sure
7. number 2 for 1 hour you would send the following SMS message to the unit RLY2 03600 Return Message RLY2 03600 Sending the following SMS Message to unit would mean turn off the output relay number L RLY1 00000 WT1010SA USER MANUAL Rev 1 5 Technical Support Technical witura com COPYRIGHT 2009 WITURA CORPORATION SDN BHD Arm and Disarm the System Via SMS It is possible to arm and disarm the system by SMS You can send the following text command to unit Text Command DARM X X stands for ON 1 or OFF 0 value Example To arm the system you can send the following text message to the unit DARM 1 Return Message ARM To disarm the system you can send the following text message to the unit DARM 0 Return Message DISARM WT1010SA USER MANUAL Rev 1 5 Technical Support Technical witura com COPYRIGHT 2009 WITURA CORPORATION SDN BHD WT 1010SA USER MANUAL 6 Miscellaneous Settings Inquire All Programmed Administrator Number via Voice To inquire all administrator numbers you can press 32 to proceed 1 1234567890 All the administrator numbers will be displayed in sequence Deleting the Administrator Number via Voice Example To delete the programmed administrator number 1 you can press 1 to proceed Simply press to delete WT1010SA USER MANUAL Rev 1 5 Technical Support Technical witura com COPYRIGHT 2009 WI TURA CORPORA
8. the following SMS command to the unit The time is entered in 24 Hour format Text Command SETM HH MM SS HH stands for 2 digits value Hour MM stands for 2 digits value Minute SS stands for 2 digits value Seconds Example When SETM 08 30 15 is applied the time 08 30 15 will be stored inside the WT 1010SA memory Return Message SETM OK 5 2 Editing the Message Contents of Auto Test Up to 50 Characters The message contents can be edited and programmed up to 50 characters You can change the displayed text by sending the following commands by SMS message to the unit Note Only support normal abc ABC English text no special characters Text Command TSMS XXXXXX WT1010SA USER MANUAL Rev 1 5 Technical Support Technical witura com COPYRIGHT 2009 WITURA CORPORATION SDN BHD XXXXXX stands for message contents Example If you want the SMS Report to display Status Online you would send the following SMS message to the unit TSMS Status Online Return Message TSMS Status Online 5 3 Editing the Inputs Alert Messages When High Pulse The Input Alert Message can be edited and programmed up to 50 characters You can change the displayed text by sending the following commands by SMS message to the unit Note Only support normal abc ABC English text no special characters Text Command USE N XXXXX xX N stands for Input number 1 4 XXXXXX stands for aler
9. 5 to proceed AUTO ANSWER ON amp amp OFF AUTO ANSWER ON amp amp OFF 1 To turn on this function simply press 1 To turn off this function simply press O AUTO ANSWER ON amp amp OFF 1 Default Value 0 Note Once this function is turned on the attached fixed line phone will not ring when there is an incoming call Arm and Disarm Command via Voice Press 123456 to arm the system when WT 1010SA answered the call Press 123456 to disarm the system when WT 1010SA answered the call Note 123456 is a 6 digits password that is programmable by O function or PAWO command by SMS at page 30 and page 38 WT1010SA USER MANUAL Rev 1 5 Technical Support Technical witura com COPYRIGHT 2009 WI TURA CORPORATION SDN BHD WT 1010SA Programming Instructions Via SMS Programming the WT 1010SA can also be done via SMS commands using your phone Any programming command sent by SMS must be in CAPITAL letters The fields between square brackets are parameters do NOT enter the square brackets When you send a command you will receive the answer for the first time even if your GSM number is not in the administrator list This happens because the WT 1010SA recognizes any GSM number as administrator and answers to it Warning The administrator number must be programmed into the WT 1010SA unit first via voice mode in order to use SMS programming mode 5 1 Time Setting To set the time you can send
10. AA A A A A y 5l Auxiliary 5 Output when PSTN Failure WT1010SA USER MANUAL Rev 1 5 Technical Support Technical witura com COPYRIGHT 2009 WI TURA CORPORATION SDN BHD Step 11 Setting for AC Failure To turn on this function you can press 31 to proceed ADC ME AL CA1 CA2 ADC ME 1 AL 1 CA1 1 CA2 1 Example Setting the unit to generate an Alert Message call the administrators generate a pulse 5V and sound the audible alarm when AC failed Simply input 1111 ADC ME 1 AL 1 CA1 1 CA2 1 OK Description ME stands for generation of SMS when AC failed Default 0 AL stands for sounding the audible alarm when AC failed Default 0 CA1 stands for calling the administrators when AC failed Default 0 CA2 stands for calling the administrators when AC connected Default 0 Value ON 1 or OFF 0 Auxiliary Power Down Output Facility via PI N9 In additional to the alarm and text alert on AC failure the system also has a second permanent 5V output continuously supplied from the battery backup via PIN9 output of the unit which will remain available for the period of AC unavailable Auxiliary 5 Output when AC Failure Note Power Down Output facility can be used on alarm panel for alert notification WT1010SA USER MANUAL Rev 1 5 Technical Support Technical witura com COPYRIGHT 2009 WI TURA CORPORATION SDN BHD Step 12 Setting for Ove
11. ION SDN BHD
12. MHz GSM1800MHz Stability of frequency better than 2 5PPM Signal sensitivity 103dBM Transmit power lt 2w Power 220v 15 AC 10 Input Voltage Tolerances 1 20VDC 11 The max distance between terminal and telephone 100M A A EA RA O WT1010SA USER MANUAL Rev 1 5 Technical Support Technical witura com COPYRIGHT 2009 WI TURA CORPORATION SDN BHD Warranty Witura Corporation Sdn Bhd guarantees all WT 1010SA GSM Fixed Wireless Terminal against defective parts and workmanship Witura Corporation Sdn Bhd shall at its option repair or replace the defective equipment upon the return of such equipment to any Witura branch This warranty applies ONLY to defects in components and workman ship and NOT to damage due to causes beyond the control of Witura such as incorrect voltage lightning damage mechanical shock water damage fire damage or damage arising out of abuse and improper application of the equipment Note Wherever possible return only the PCB to Witura Service Centres DO NOT return the enclosure The WT 1010SA is a product of Witura Corporation Sdn Bhd And is manufactured by Shenzhen Witura Telecommunications Co Ltd WARNING For safety reasons only connect equipment with a telecommunications compliance label This includes customer equipment previously labelled permitted or certified WT1010SA USER MANUAL Rev 1 5 Technical Support Technical witura com COPYRIGHT 2009 WITURA CORPORAT
13. System asnicar N IS Step15 Enable the Remote CoOntrOl m m mem es sm cs escece cee m canes eset ees ms aeea esata ees nes meanest et etesmsaeeaeaanansmsaemess N Ul Step16 Setting the Automatic Call Answering Feature cmcacocneneninimenenenenenimenamememrmr mamen 5 WT LOLOSA Configuration Instructions Via SMS ocucncucncnenenenonenonenenonememememememememememe e PO a N NBR DD QA 0 5 2 Editing the Message Contents Of Auto T eSt ncucccucncncnenonenincnimeme men 5 3 Editing the Input Alert Messages When High Pulse cocccnincncuomenensninimenomemenincac mamen 5 4 Editing the Input Alert Messages When No Pulse ocococmccncncnimomomenenoninimomemencanrame mame marras O dido e lio A A o e io O E a E E 5 6 Arm and Disarm the System Via SMS ocmucmcnoneneneninononononono nome N N N BN O CO N N WT1010SA USER MANUAL Rev 1 5 Technical Support Technical witura com COPYRIGHT 2009 WI TURA CORPORATION SDN BHD O MISCOllaReDuS gt CLOS doit 2 Zs TCIM GAN SS CIT ICAL OINS nsec ety adela ct ear lis dica WT1010SA USER MANUAL Rev 1 5 Technical Support Technical witura com COPYRIGHT 2009 WITURA CORPORATION SDN BHD UV 1 Introduction to the WT 1010SA GSM Alarm System The WT 1010SA GSM Alarm System provides the ideal solution for residential commercial applications rural and farm security where traditional telephone lines are not available for security system communications Wh
14. TION SDN BHD WT 10105A USER MANUAL Changing the Programming Mode Password via Voice To change the 6 digits programming mode password you can press 0 to proceed NEW PASSWORD NEW PASSWORD 654321 Input new password and ended with NEW PASSWORD 654321 OK Inquire the status of the Recipients that will receive Alert Messages via Voice To inquire the status of the recipients you can press 19 to proceed RECIPIENTS 11111111 The status will be displayed on screen Press to turn back Checking the Signal Strength via Voice To check the signal strength you can press 20 to proceed Yull CSQ lt 23 gt The signal strength will be displayed on screen Press to turn back WT1010SA USER MANUAL Rev 1 5 Technical Support Technical witura com COPYRIGHT 2009 WI TURA CORPORATION SDN BHD Setting the Waiting Time for Engaged Call via Voice In the event the administrator has not answered the call or engaged it could take a while for the WT 1010SA to call the next number You can shorten the time for every call by programming the waiting time Press 12 to proceed WAIT TI ME WAIT TIME 20 Hi Example To set the waiting time for 20 seconds Simply input 20 and ended with WAIT TIME 20 OK Note The waiting time is a 2 digits value range from 20 59 seconds Default 30 seconds Setting Arm Delay Time Input 1 Only Input 1 can be programm
15. a certain group of numbers for PSTN AC failure or Auto Test you can press 29 to proceed CALL CALL 5 ii Example Setting the unit to dial the first 5 administrator numbers Simply press 5 CALL 5 OK Step 9 Setting for Auto Test 9 1 Time Setting To setup time you can press 16 to proceed WT1010SA USER MANUAL Rev 1 5 Technical Support Technical witura com COPYRIGHT 2009 WITURA CORPORATION SDN BHD TI ME 08 30 00 Example To set the time at 8 30am Simply input digits and ended with TI ME 08 30 00 9 2 Setting the Auto Test Report Time Section 1 The system has the function of sending the test report to the administrators at the programmable time section The time is entered in 24 Hour format To program the auto test report time section 1 you can press 17 to proceed DSTM1 12 00 00 Example To set the auto test report time at 12 00pm Simply input digits and ended with DSTM1 12 00 00 OK 9 3 Setting the Auto Test Report Time Section 2 The system has the function of sending the test report to the administrators at the programmable time section The time is entered in 24 Hour format To program the auto test report time section 2 you can press 42 to proceed WT1010SA USER MANUAL Rev 1 5 Technical Support Technical witura com COPYRIGHT 2009 WI TURA CORPORATION SDN BHD DSTM2 18 00 00 Example To set the auto te
16. dial the WT 10105A unit s phone number from another phone and its attached phone will ring as a normal landline phone would If there is a busy tone on the attached telephone set either the line you are calling is busy or the GSM communicator is busy with previous communication at that moment for example data transfer to the monitoring station Note Some telephone sets are sensitive to the GSM radio signal For this reason you may hear a characteristic noise in the telephone receiver when calling If the noise is disturbing change the location of the phone set try to keep it as far as possible from the WT 1010SA unit antenna Usually it is possible to find a suitable location for the phone with minimal level of interference WT1010SA USER MANUAL Rev 1 5 Technical Support Technical witura com COPYRIGHT 2009 WITURA CORPORATION SDN BHD WT 10105A USER MANUAL 4 WT 10105SA Programming Instructions Via Fixed Line Phone 4 1 Introduction The WT 1010SA can be programmed manually by a connected normal telephone Single Line Phone Connect to Phone Port Note Before commencing programming it is advisable to read the below programming setting instructions thoroughly To start with programming user must plug in a normal single line phone to TEL1 Port 1 Step 1 Enter Programming Mode Pick up the handset or press hands free press 123456 to enter programming mode If the password has entered correctly yo
17. e Please refer to programming instructions via SMS for editing the message content of Auto Test on page 26 WT1010SA USER MANUAL Rev 1 5 Technical Support Technical witura com COPYRIGHT 2009 WI TURA CORPORATION SDN BHD Step 10 Setting for PSTN Failure To turn on this function you can press 30 to proceed PST ME OU AL CA1 CA2 PST ME 1 OU 1 AL 1 CA 1 CA2 1 Example Setting the unit to generate an Alert Message call the administrators generate a pulse V and sound the audible alarm when PSTN failed Simply input 11111 PST ME 1 OU 1 AL 1 CA 1 CA2 1 OK Description ME stands for generation of SMS when PSTN failed Default 0 OU stands for generation of pulse 5V at PIN8 when PSTN failed Default 0 AL stands for sounding the audible alarm when PSTN failed Default 0 CA1 stands for calling the administrators when PSTN failed Default 0 CA2 stands for calling the administrators when PSTN connected Default 0 Value ON 1 or OFF 0 Auxiliary PSTN Failure Output Facility via PI N8 In additional to the alarm and text alert on PSTN failure the system also has a permanent 5V output continuously supplied from the unit via PIN8 output which will remain available for the period of PSTN unavailable Note PSTN Failure Output facility can be used on alarm panel for alert notification S NN mm FT i A h A y A A e U eE ea a
18. ed to arm after a preset time when the Arm button is pressed or Arm function is activated by fixed line phone To program the delay time you can press 47 to proceed ARM TI ME ARM TI ME 30 Example To set the arm delay time for 30 seconds Simply input 30 and ended with WT1010SA USER MANUAL Rev 1 5 Technical Support Technical witura com COPYRIGHT 2009 WI TURA CORPORATION SDN BHD Note The Arm Time is a 2 digits value range from 00 59 seconds Default 00 seconds Enable Disable System Power Up SMS Notification The system is able to generate SMS notification whenever the WT 1010SA is turned on To enable this function you can press 48 to proceed POWER UP MSG ON amp amp OFF POWER UP MSG ON amp amp OFF 1 To enable this function simply press 1 To disable this function simply press O POWER UP MSG ON amp amp OFF 1 Default Value 0 Enable Disable System Armed SMS Notification The system is able to generate SMS notification whenever user armed the WT 1010SA To enable this function you can press 49 to proceed ARM MESSAGE ON amp amp OFF ARM MESSAGE ON amp amp OFF 1 WT1010SA USER MANUAL Rev 1 5 Technical Support Technical witura com COPYRIGHT 2009 WITURA CORPORATION SDN BHD To enable this function simply press 1 To disable this function simply press O ARM MESSAGE ON amp amp OFF 1 Default Value 0 Disab
19. en no telephone service is available from your home it ensures that critical alarm information reaches the central station The WT 1010SA uses a GSM communicator no distance limits to receive alarm calls or remote control the alarm system it can also call and sends text alerts to 8 pre set telephone number when intruder alarm triggers 2 Main Features of the WT 1010SA Four digital inputs The system has the function to send SMS and call to the user in the event of input triggered For example Zone 4 connected to an electric door when there is intruder or the electric door is open illegally WT 1010SA will receive short circuit impulse on Zone 4 and automatically sends a signal to the pre set number and notify the owner It is possible to arm disarm the unit remotely via remote control SMS or phone call Alternatively it also can connect to the basic telephone to perform arm disarm Input alarm zoning can be edited and programmed up to 50 characters long You can use this function to program any languages You can change the displayed text by sending a command by SMS to the unit For examples changing the zone 4 to DOOR OPEN If the alarm zoning is not enough the system is offering lopping concept It can lop up to 50 zoning Three remote control outputs These open collector outputs that can sink max 300ma per output can be turned on and off remotely through a SMS or phone call Remote control will be reachable by sending
20. ext Command PAWO XXXXXX XXXXXX stands for 6 digits New Password Example To change the password to 654321 you would send the following SMS command to the unit x PAWO 654321 Return Message PAWO OK Inquire the Status of Inputs PSTN and AC To inquire the status of inputs PSTN and AC you can send the following SMS command to the unit Text Command CTC Example of Return Message PSTN O INPUT2 1 _ INPUT3 O INPUT4 Input 2 triggered Input 4 normal Sound the Audible Alarm Manually It is possible to sound the alarm manually by sending the following SMS command to the unit which remain active for the period of time set Text Command WT1010SA USER MANUAL Rev 1 5 Technical Support Technical witura com COPYRIGHT 2009 WITURA CORPORATION SDN BHD ALNF X X stands for ON 1 or OFF 0 value When ALNF 1 Is applied means audible alarm will sound When ALNF 0O Default is applied means audible alarm will turn off Reset the WT 1010SA unit via SMS To reset the unit you can send the following command by SMS to the unit Text Command REST XXXXXX XXXXXX stands for 6 digits password based on PAWO Default 123456 and it can be changed anytime Return Message REST OK Technical Specifications Environment temperature 0 50 C Relative humidity 10 95 Air pressure 86 106kpa Environment yawp 60dB A Working frequency GSGM900
21. ipients Simply input 11111111 SECT 11111111 OK Note The input for this setting is an 8 digits value ON 1 or OFF 0 only Each of them represents administrator 1 8 Default Value 10000000 Step 5 Programming the Area Code To program area code you can press 9 to proceed WT1010SA USER MANUAL Rev 1 5 Technical Support Technical witura com COPYRIGHT 2009 WI TURA CORPORATION SDN BHD NEW AREA 03 Enter area code 03 for example and ended with NEW AREA 03 OK Area code has programmed successfully Step 6 Setting the Function of Adding Area Code when Transmitting an Alarm To turn on off this function you can press 14 to proceed AREA ON amp amp OFF AREA ON amp amp OFF 1 To turn on this function simply press 1 To turn off this function simply press O AREA ON amp amp OFF 1 Default Value 0 Step 7 Setting the Delay Time for Transmitting a Dialing Number To set the delay time you can press 34 to proceed DTTRANSMIT WT1010SA USER MANUAL Rev 1 5 Technical Support Technical witura com COPYRIGHT 2009 WI TURA CORPORATION SDN BHD DTTRANSMIT 07 Example To set the required delay time at 7 seconds Simply press O7 DTTRANSMIT 07 OK Note The Delay Time is a 2 digits value range from 00 59 seconds Default 00 seconds Step 8 Setting for calling a group of Administrator numbers To program the unit to dial
22. le the Remote Control To disable the remote control you can press 50 to proceed DELETE RF ON amp amp OFF DELETE RF ON amp amp OFF 1 To disable remote control press 1 To cancel press O DELETE RF ON amp amp OFF 1 Default Value 0 Setting the Input Alarm Delay Time Input 2 3 and 4 Only Input 2 3 and 4 can be programmed to generate SMS alerts alarms or dialing administrator numbers after a preset time when they are triggered To program the alarm delay time you can press 51 to proceed I N2D TIME WT1010SA USER MANUAL Rev 1 5 Technical Support Technical witura com COPYRIGHT 2009 WI TURA CORPORATION SDN BHD IN2D TIME 60 Example To set the alarm delay time for 60ms Simply input 60 and ended with Note The Alarm Delay Time is a 2 digits value range from 00 99ms Default 00ms You may continue programming Input 3 and Input 4 Alarm Delay Time by pressing B2 or 53 Activate Output Relay to stay on for a specific time via Voice To activate output relay 1 to stay on for a specific time you can press 21 to proceed RLY1 00050 RE 1 Example To activate relay 1 to stay on for 50 seconds and with SMS reply from the unit after relay has turned off Simply input 000501 RLY1 00050 RE 1 OK Note RE stands for generation of SMS when relay off value ON 1 or OFF 0 You may continue to activate relay 2 or relay 3 by pres
23. nical Support Technical witura com COPYRIGHT 2009 WITURA CORPORATION SDN BHD 3 2 WT 1010SA Inputs and Outputs Wiring Instructions RLY1 OUT1 RLY2 OUT2 RLY3 OUT3 Remote Controlling Outputs These open collector outputs can be turned on and off remotely through a SMS Remote control will be reachable by sending a SMS with a certain command Note When sending normal SMS with command below the WT 1010SA will turn On Off the output relay and reply a message of output has turned On Off to a programmable phone numbers ZONE1 IN1 ZONE2 IN2 ZONE3 IN3 ZONE4 IN4 Inputs Connect ZONE1 ZONE2 ZONE3 and ZONE4 to inputs panel when there is a short circuit impulse on ZONE1 ZONE2 ZONE3 ZONE4 the WT1010SA is possible to send SMS to a programmable phone numbers For Example ZONE4 is connected to an electrical door when there is intruder or the electrical door is opened illegally WT1LO1OSA will receive short circuit impulse on ZONE4 and will automatically send a signal to the monitoring station and also send a SMS to notify the owner INPUT OUTPUT A 2 2K Resistor must be attached along with the sensors for all inputs Inputs and Outputs Wiring Diagram WT1010SA USER MANUAL Rev 1 5 Technical Support Technical witura com COPYRIGHT 2009 WITURA CORPORATION SDN BHD 3 3 Installing the SIM Card Note Installing the SIM Card Please be sure the initial 4 digit PIN code of SIM card is disabled
24. ound When Auto Test it will generates Beep endless sound WT1010SA USER MANUAL Rev 1 5 Technical Support Technical witura com COPYRIGHT 2009 WITURA CORPORATION SDN BHD Step 15 Enable the Remote Control The WT 1010SA also comes with a RF remote control It allows you to arm or disarm the system easily from a close distance To enable the remote control you can press 45 to proceed RF STARY Button C Activate Relay 1 Button A Arm Button D Activate Relay 2 Button B Disarm Button B Disarm Press the Arm or Disarm button on Remote RF STARY OK The remote control is activated successfully Now you are able to arm and disarm the system with remote control When the system is in Armed Mode a lock icon will be displayed as shown below Yull a WT 1010 When the system is in Disarmed Mode an unlock icon will be displayed as shown below Yull e WT 1010 Note 4 units remote control are allowed on this system WT1010SA USER MANUAL Rev 1 5 Technical Support Technical witura com COPYRIGHT 2009 WI TURA CORPORATION SDN BHD Step 16 Setting the Automatic Call Answering Feature The WT 1010SA can be programmed to answer all incoming calls automatically even there is no fixed line phone attached to it When the call is answered it allows the owner to arm or disarm the system by entering a command from their phone s keypad To turn on this function you can press 3
25. pen Default 0 CA2 stands for calling the administrators when input triggered close Default 0 Value ON 1 or OFF 0 WT1010SA USER MANUAL Rev 1 5 Technical Support Technical witura com COPYRIGHT 2009 WI TURA CORPORATION SDN BHD Y N1OSA UY 2 MANUA You may continue to activate Input 2 Input 3 and Input 4 functions by pressing 25 26 or 46 Note Please refer to programming instructions via SMS for editing the Input Alert messages on page 27 Step 14 Arm and Disarm the System Via Fixed Line Phone To arm the system you can press 10 to proceed ARM OR DISARM ON amp amp OFF ARM OR DISARM ON amp amp OFF 1 Example To arm the system simply press 1 To disarm the system simply press O ARM OR DISARM ON amp amp OFF 1 System armed successfully Note In Armed mode the WT 1010SA can generate SMS alerts alarms and dialing the administrator numbers when the inputs triggered Auto Test PSTN failed or AC failed Alarm Indicator When dialing the Administrator numbers When Input 1 triggered it will generates Beep continuous sound When Input 2 triggered it will generates Beep x 2 continuous sound When Input 3 triggered it will generates Beep x 3 continuous sound When Input 4 triggered it will generates Beep x 4 continuous sound When AC failed it will generates Beep x 5 continuous sound When PSTN failed it will generates Beep x 6 continuous s
26. rcoming GSM Jammers amp GSM Tower Failure 12 1 Enable Disable the function of Activate Output Relay 1 when GSM lammer is detected To turn on this function you can press 38 to proceed NETWORK ON amp amp OFF NETWORK ON amp amp OFF 1 To turn on this function simply press 1 To turn off this function simply press O NETWORK ON amp amp OFF 1 OK Note Alarm siren connected to PIN6 PIN7 will sound when jammer is detected 12 2 Setting the Parameter for Network Failure To set the parameter you can press 39 to proceed NETDT1 RLY1 NETDT1 05 RLY1 05 Example To set the network failure time for 5 seconds and the turn on time of Relay 1 for 5 seconds Simply press 0505 NETDT1 05 RLY1 05 OK WT1010SA USER MANUAL Rev 1 5 Technical Support Technical witura com COPYRIGHT 02009 WI TURA CORPORATION SDN BHD Description NETDT1 stands for network failure time range from 00 59 seconds Default 6 seconds RLY1 stands for turn on time of Relay 1 when network fails 00 59 seconds 00 means RLY1 will stay ON permanently 12 3 Enable Disable the function of Activate Output Relay 2 when GSM Tower Failure To turn on this function you can press 40 to proceed NO SIGNAL ON amp amp OFF NO SIGNAL ON amp amp OFF 1 To turn on this function simply press 1 To turn off this function simply press 0 NO SIGNAL ON amp amp OFF 1 OK Note
27. sing 22 or 23 WT1010SA USER MANUAL Rev 1 5 Technical Support Technical witura com COPYRIGHT 2009 WI TURA CORPORATION SDN BHD Setting the Alarm Time for Audible Alarm via Voice To set the alarm time for audible alarm you can press 33 to proceed ALARM ALARM 03600 LN Example To set the audible alarm to sound for 1 hour when triggered Simply press 03600 ALARM 03600 OK Note The alarm time must enter in 5 digits range from 00005 99999 Default 00010 seconds Setting the WT 10105SA to ignore the front dialing digits when dialing the Administrator number via Voice This function is useful when the WT 1010SA is connected to the PABX system where Access Digits are required for Extension Line Centrex Line To set the unit to ignore the front dialing digits you can press 44 to proceed A Example To set the unit to ignore first 2 dialing digits Simply press 2 WT1010SA USER MANUAL Rev 1 5 Technical Support Technical witura com COPYRIGHT 2009 WI TURA CORPORATION SDN BHD DEL NUM 2 OK Note The value is O 4 Default 0 Adjusting the Speaker and Microphone Volume level via Voice To adjust the speaker and microphone volume level you can press 11 to proceed SPK 3 MIC 3 Example To adjust the speaker volume to 3 and microphone volume to 3 Simply press 33 SPK 3 MIC 3 OK Note Both SPK and MIC volume level range from 1
28. st report time at 18 00pm Simply input digits and ended with DSTM2 18 00 00 OK Note Skip this setting if only 1 time section is needed 9 4 Setting the Auto Test Report Time Section 3 The system has the function of sending the test report to the administrators at the programmable time section The time is entered in 24 Hour format To program the auto test report time section 3 you can press 43 to proceed DSTM3 23 59 00 Example To set the auto test report time at 23 59 pm Simply input digits and ended with DSTM3 23 59 00 OK Note Skip this setting if only 1 time section is needed WT1010SA USER MANUAL Rev 1 5 Technical Support Technical witura com COPYRIGHT 2009 WI TURA CORPORATION SDN BHD 9 5 Enable Disable the function of dialing the programmed Administrator number for Auto Test To turn on this function you can press 27 to proceed DTI MEC ON amp amp OFF DTI MEC ON amp amp OFF 1 To turn on this function simply press 1 To turn off this function simply press O DTI MEC ON amp amp OFF 1 Default Value 0 9 6 Enable Disable the generation of SMS Report for Auto Test To turn on this function you can press 28 to proceed DTI MEM ON amp amp OFF DTIMEM ON amp amp OFF 1 To turn on this function simply press 1 To turn off this function simply press O DTI MEM ON amp amp OFF 1 Default Value 0 Not
29. t message content Example If you want the alert message to display Garage Opened when input 1 triggered you would send the following SMS message to the unit USE1 Garage Opened Return Message USE1 Garage Opened 5 4 Editing the Inputs Alert Messages When No Pulse The Input Alert Message can be edited and programmed up to 50 characters You can change the displayed text by sending the following commands by SMS message to the unit Note Only support normal abc ABC English text no special characters Text Command USC N XXXXXxX N stands for Input number 1 4 WT1010SA USER MANUAL Rev 1 5 Technical Support Technical witura com COPYRIGHT 2009 WITURA CORPORATION SDN BHD XXXXXX stands for alert message content Example If you want the alert message to display Garage Closed when input 1 triggered you would send the following SMS message to the unit USC1 Garage Closed Return Message USC1 Garage Closed 5 5 Output Settings 5 5 1 Activate Output Relay to Stay On for a Specific Time To activate the output relay you can send a text command via SMS specifying the number of seconds the output should stay on to the unit It is possible to set up to maximum of 99 999 seconds Text Command RLY N XXXXX N stands for Output number 1 3 XXXXX stands for 5 digits value The number of seconds 00000 99999 For example assume you want to turn on the output relay
30. that in case of emergency the GSM still functioning well Standby rechargeable battery to prevent power failure or electricity cut off by intruder The GSM will function as normal when no electricity supply LCD display to check the GSM signal strength and battery capacity 3 Installation Instructions Note It is essential that you read the step by step instructions fully prior to installing and programming the unit 3 1 Description Antenna connect the antenna to the GSM module place the antenna as far as possible from the WT 1010SA and do not leave any coiling of the antenna cable to avoid radiant interference SIM Card disable the PIN code and set it to 1234 default For Transmitter Mode Data_or SMS as with any transmitter it requires an identifier receiver telephone numbers etc refer to the complete information on Programming page Line Input connect the line input to the PSTN or ISDN network Outputs Back Up Mode connect to additional remote controlling outputs Alarm Input connect the input to output of the Alarm Panel Control Panel Power Supply connect to a 12VDC power supply Operating State Approximately 20s after power up check the operating state indicated by the Power LED the LED is steady during power up phase and then blinks when the connection to the GSM network is established The Signal indicator LED will stay lit whenever there is signal WT1010SA USER MANUAL Rev 1 5 Tech
31. u should see HAND FREE displayed on WT 1010SA screen Now you may proceed with programming settings ENTER SETTING When pick up the handset ENTER OK SETTI NG Password entered correctly WT1010SA USER MANUAL Rev 1 5 Technical Support Technical witura com COPYRIGHT 2009 WI TURA CORPORATION SDN BHD Programming Mode Step 2 Reset the WT 1010SA Unit To reset the unit you can press 15 to proceed REST ON amp OFF REST ON amp OFF 1 Then press 1 to reset REST ON amp OFF 1 Note It is advised that you should reset the WT 1010SA unit before proceeding to the below programming section Step 3 Programming the Administrator Number Continue pressing 1 to start programming the administrator number 1 TEL 13232353646 1 Enter administrator number 13232353646 for example and ended with WT1010SA USER MANUAL Rev 1 5 Technical Support Technical witura com COPYRIGHT 2009 WI TURA CORPORATION SDN BHD Number has programmed successfully You may continue to program administrator number 2 3 4 5 6 7 and 8 by pressing D BK AK HK 6 7 gx Step 4 Setting the Recipient that will receive Alert Messages The unit can send text alerts to 1 or all 8 of the programmed administrator s numbers To do this setting you can press 18 to proceed SECT SECT 11111111 Example To turn on this function for all rec
Download Pdf Manuals
Related Search