RMX-108 user`s manual
Contents
1. has successfully learned a function it beeps once and the LED lights up until you release the remote control s button Deleting codes You can delete codes if you no longer want to use the function or if you want to re program a button You can delete codes one button at a time or an entire device at a time NOTES e Deleting codes does not remove the button from the layout e You do not need to delete a code to Re program a button You can overwrite codes by automatically or manually entering preset codes or by learning from an existing remote Roksan RMX 108 User s Manual Deleting codes one button at a time l 6 Select the appropriate device by pressing the device button Press and hold to enter setup Press EXIT MACRO Press the button you want to delete CODE LEARN Repeat step 4 for all the a ata buttons you want to iF _J j delete N Press Deleting codes one device at a time 1 Select the appropriate device by pressing the device button Press and hold to enter setup Press pow Press m to confirm Otherwise press je to cancel To delete other devices repeat steps 1 3 Otherwise press to leave this mode CODE LEARN JL IDEL DEL BANK RESET JL Creating Macros Creating Macros A macro is a sequence of commands The Macro feature enables you to send a sequence of up to 60 commands by pressing a single but2. 4 The RMX 108 does not Check the correct device is operate a device selected on the RMX 108 Make sure you are using the RMX 108 within the effective transmission distance 8 10m The batteries may be discharged Replace the batteries as described in Installing batteries on page 4 Check that the button is programmed correctly Re program the button as described in page 4 17 Troubleshooting Problem solution The RMX 108 cannot operate a device after learning a function Check the RMX 108 has learned the function correctly Delete the code and teach the remote again Check you used the correct remote to teach the Rmx 108 cannot learn all codes Some remote s frequency might be out of the learning range You may not be able to program the RMX 108 for some devices or functions The RMX 108 emits three beeps when learning a function Check the remote is correctly aimed at the RMX 108 s learning eye and you are holding the remote s button until the function is learned Check the remote s IR transmitter is 5 10 cm from the RMX 108 s learning eye 18 Roksan RMX 108 User s Manual Problem solution The LED does not light The LED does not light up up when you press a when the button doesn t have button a function in it Please input an IR codes init Check the button that you pressed has been programmed the code in it Th
3. Roksan RMX 108 User Manual Roksan RMX 108 User s Manual RMX 108 Features Macro sequence function each macro can store 60 commands Controls up to six devices including DVDs TVs Satellite Receivers VCRs and other infrared remote control devices IR code learning from existing remote controls for quick configuration Preset manufacturer s codes for many models Up to 44 user programmable keys for each device Automatic Power Saving mode turns off the remote after 90 seconds of inactivity Unpacking the RMX 108 Check the package to make sure the following items are included RMX 108 Batteries Roksan RMX 108 User s Manual Battery Indicator A battery icon is displayed in the upper left hand corner above the Mute button aw Sene MUTE When the batteries are almost discharged the battery low icon appears Roksan RMX 108 User s Manual About the controls The number of soft buttons on the touch screen changes according to the selected device The touch screen soft buttons allow you to operate the RMX 108 and your external devices Use these keys to program codes from your existing remotes control your devices and set up macros You will hear a beep when you press a button The RMX 108 turns itself off after 90 seconds of inactivity Touch screen precautions Tap the LCD touch screen gently Do not use excessive force Do not use pens or sharp objects to tap the screen as you might d
4. amage the surface Keep the RMX 108 dry Wipe off any spills immediately Never immerse it in liquid Do not expose the RMX 108 to extreme temperatures Keep it away from heat SOUICes Avoid dropping the RMX 108 Do not drop anything on the touch screen Clean the LCD touch screen with a soft damp cloth Do not use abrasives or cleaning solutions About the controls Selecting devices and pages You can program the hard buttons as well as two pages of soft buttons on the touch screen for up to six devices To change between devices press the appropriate device button To switch between pages press the device button again The current page is indicated by P4 or P2 in the top right corner of the touch screen Setting up the RMX 108 Entering setup To enter setup press and hold the button for two seconds From the setup screen you can e Setup preset codes e Learning codes e Creating Macros e Delete key codes e Delete devices codes e Reset the handset EXIT MACRO TE N Vf CODE LEARN TVVIDEO MTS SLEEP aE CS RE 2 LJL_J MD f 1 TEL DEL BANK RESET INFO NOTES When the battery low icon appears you will not be able to enter setup Please renew batteries to entering setup Learning codes Roksan RMX 108 User s Manual Learning codes You can use your existing IR remote control to teach the RMX 108 You can program alll buttons except for the DEVICE ke
5. e VCR Hard disk The record button has a safety recorder or DVD will feature to prevent accidental not record operation Press and hold the record button for two seconds Learning does not The batteries may be work discharged Replace the batteries as described in Installing batteries on page 4 Check the target device s remote is correctly aimed at the RMX 108 s learning eye and keep distance between remotes to about 5 10 cm 19 Troubleshooting Problem solution Check you are holding the target remote s button until the LED lights up to confirm this function is learned Do not teach the SRC 1600 near incandescent lights Sometimes the code s frequency is out of the learning range The SRC 1600 cannot learn all codes You may not be able to program the SRC 1600 for some devices or functions Macro does not work Check the correct device is selected on the SRC 1600 Check you are using the SRC 1600 within the effective transmission distance 8 10 m The batteries may be discharged Replace the batteries as described in Installing batteries on page 4 Check that the macro is programmed correctly Re program the macro as described in Creating Macros on page 19 33 SRC 1600 User s Manual Problem solution A button on your existing remote performs two or more functions Some remotes issue multiple codes when a single button is pr
6. essed Teach separate buttons on the SRC 1600 for these different codes The touch screen turns off The SRC 1600 has a power saving feature and switches off automatically after 90 seconds of inactivity To switch it back on again please move the SRC 1600 The batteries may be discharged Exchange the new batteries for SRC 1600 34
7. o the original factory setup You will lose all macros and user defined buttons Resetting defaults cannot be undone 1 Press and hold to enter setup MACRO 2 Press and hold for four seconds CODE LEARN The touch screen goes blank Sean and the LED lights up The reset process is complete 12 Record button protection Record button protection aw The SRC 1600 has a protection feature to prevent accidental recording of videotapes hard disks or DVDs The record button must be pressed for two seconds to begin recording NOTE This only applies to the record button If you program another button to record this safety feature will not work for that button Punch thru The punch thru function enables you to access the VOL controls of the TV or RECV device without having to switch to that device For example while you are watching a DVD you can adjust the volume of your TV using punch thru 13 Roksan RMX 108 User s Manual Press and hold the device button of the device you are currently operating While holding the device button press the VOL or VOL button The device icon flashes on the touch screen While the device icon is flashing quickly press TV or RECV within three seconds Punch thru has successfully completed When punch thru has been set the TV or RECV icon will flash next to the device icon of the device you are operating to indicate the
8. ton The macro can also include delays NOTE Assigning a macro to any button overwrites any previous function 1 Select the appropriate device by pressing the device button 2 Press and hold m to enter setup 3 Press P CODE HCLEARN O E IDELI DEL BANK RESET CJl 4 Press the button to which you want to assign the macro A double beep sounds to indicate macro mode 5 Press the buttons in the sequence of your commends for a Macro If necessary to insert a delay by press fe flashes in the T button Press the desired EXIT MACRO EET jL DELAY delay in seconds on the number buttons For example for a three second delay press 3 6 When you have completed the macro press or ey 10 Roksan RMX 108 User s Manual 7 Press to confirm or to discard the macro The button s original function will be preserved 8 To set another macro repeat steps 3 7 9 After you have finished setting macros press re __ to leave this mode NOTES e Each macro can store up to 60 commands including delays When the macro is full you cannot enter any more commands If you try to enter more commands a triple beep will sound e You can delete macros in the same way as you would buttons See Deleting codes on page 17 11 Resetting factory defaults Resetting factory defaults Resetting factory defaults deletes all functions and restores them t
9. volume control source NOTE e Toremove the punch thru function press the device button and Volume or Volume together e The punch thru function can only be set with the DVD VCR SAT and AUX devices and enables you to control the volume of these sources through the TV or RECV device 14 Auto power off Auto power off To save power the RMX 108 automatically powers off after 90 seconds Backlight The RMX 108 has a green backlight to make using it in the dark room easily Press the backlight switch to switch on the backlight The backlight will switch off automatically 8 seconds after the last button is pressed 15 Appendix Specifications Model Capacity Dimensions W x H x D Weight W O batteries Buttons Backlight IR operating distance Learning frequency Memory Batteries Power consumption Roksan RMX 108 6 devices in one 58 mm x 198 mm x 28 mm 160g 44 programmable buttons 6 device buttons backlight button green LED 8 10 meters 20KHZ 455KHZ amp Pulse up to 256 bits long 512 KB flash memory 4x AAA 1 5 V SUM 4 Operation 30 120 mA max LCD on 150 pA LCD off 20 yA 16 Roksan RMX 108 User s Manual Troubleshooting Problem solution Touch screen does not Check the batteries are display anything when installed correctly touched The batteries may be discharged Replace the batteries as described in Installing batteries on page
10. ys NOTE Not all codes can be learned If the RMX 108 cannot learn a code three beeps are emitted 1 Set both remotes on a flat surface with the target device s remote control pointed at the SRC 1600 s learning eye for about 5 10 cm apart 2 On the SRC 1600 press the device button of the device you want to program 3 Press and hold to enter MACRO Ly sere CODE LEARN _ BEC 4 Press Ls 5 On the SRC 1600 press the button to indicate the key you want to program Including Touch screen buttons and hard buttons Touch screen buttons flash when you select them Press the device button to switch between touch screen pages a DEL BANK RESET Roksan RMX 108 User s Manual 6 Aim the IR transmitter of your device s remote control at the learning eye of the RMX 108 7 Continually press the corresponding button on your existing remote control until the RMX 108 LED lights If the function is not learned correctly the LED flashes three times and the RMX 108 emits a triple beep Do the relearning procedure again 8 When the code has been learned the RMX 108 emits a beep and the LED on the RMX 108 lights until you release the button on the device s remote 9 Repeat steps 5 8 for all the buttons you want to program 10 When you have finished press elit Deleting codes NOTES e Programming a button overwrites any previous function e When the SRC 1600
Download Pdf Manuals
Related Search