Instructions - 254kb - pdf
Contents
1. this tape 1 Only use the supplied power supply for 5m 2 Only cut the tape at the highlighted 5cm intervals 3 Do not connect another reel and operate from a single power supply as this will seriously affect the performance 4 The top track of the tape is the Positive pole 5 The bottom track of the tape is the negative pole 6 Ensure you connect the correct wires otherwise the tape will not work 7 Ensure that when soldering there are no short circuits 8 We recommend use of heat shrink tubing to protect the connection 9 Check that everything operates correctly before installing 10 Place the adaptor in a dry area where possible as even the tape is rated IP68 it does not apply to the adaptor FAQ Q Can I connect different colours in a chain A Yes all the LEDs draw the same power current and have the same connection but do not exceed 5m Q Can you cut a 5m tape into many different sections then connect them all together A Yes as long as you cut the tape at 5cm intervals highlighted Q I have connected two reels together off one power supply and the LEDs are dim towards the end A This product is designed to be used at a maximum of 5m Anything longer will seriously affect the performance Q Can I connect the tape together to form a loop A Yes you can This will even the brightness out on the LEDS across the 5m length Q Can I use the tape outdoors A Yes the tape is IP68 rated Ensure that the termina2. NV fluxia WATERPROOF DIY LED TAPE KIT User Manual WATERPROOF DIY LED TAPE KIT SINGLE COLOUR Introduction Thank you for purchasing the Fluxia Waterproof DIY LED Tape Kit LED tape is ideal for use on the underside of a counter tops shelves cupboards around window frames or in an alcove of a ceiling to name just a few examples With IP68 rating allows the tape to be highly waterproof against water splashing or even under poor rain condition Before starting please ensure that you have read this instruction leaflet carefully If you are unsure about anything please have this installed by a competent installer Blister Contents 1 x 5m reel of LED tape 1 x Power supply with 3 region adaptors UK EU amp Worldwide 15 x Clips 30 x Screws 3 x Endcap Possible Required tools Scissors Craft knife Soldering iron and solder 2 core DC wire and heat shrink tube Step 1 Preparation Ensure that the surface you are attaching to is clear of dust and dirt Clean thoroughly and leave to dry before fitting the tape Unravel the tape and connect the power supply Check that all the LEDs are functioning correctly and if there are any faults return to your retailer without delay Step 2 Cutting WARNING Disconnect from the power supply before attempting any cutting Measure out each section and cut with sharp scissors at the marked 5cm intervals to achieve the perfect length Do not discard any excess tape as it can be easily reco
3. nnected and used again see FIG 2 Step 3 Fitting Example 1 Simple straight run Clear the area you wish to install the tape and remove the backing paper exposing the adhesive tape Push tape firmly onto the surface For a firm mounting make use of the screws and clips to secure the tape It is recommended to work on 50cm sections at a time in order to ensure a professional finish When you reach the end of your installation cut at the marked cutting point Example 2 Requires cutting The tape can be cut at highlighted 5cm intervals for a perfect fit FIG 1 O OJO O q You may also reconnect the two pieces by soldering the connection points together FIG 2 The tape has two tracks for the DC voltage with positive pole at the top and negative pole at the bottom To reattach use a craft knife to cut the Epoxy coating from the terminals Use a soldering iron and solder to connect the DC wire to the relative terminals be sure not to cause a short circuit when making these connections as this will result in malfunction and possible damage to the power supply Waterproof DIY LED Tape Kit User Manual NV fluxia FIG 2 gt OJO O 6O0 08 o po O Os 0 WARNING Only cut the tape on the highlighted intervals Cutting the tape in other parts without due care will permanently damage that section of the tape and will result in malfunction O OjO G SoH osho o gg Required distance Points to remember when using
4. or FAQ Q Can you cut a 5m tape in many of different sections then solder connect them all together A Yes as long as you cut the tape at 10cm intervals highlighted Q Can I connect the tape together to form a loop A Yes you can as long as both sides have a sufficient power supply it is possible Q Can I use the tape outdoors A Yes the tape is IP68 rated Ensure though that the terminated ends are covered by end caps or heat shrink protected Q Can I use the LED tape without a controller A Yes you can but you can only have a choice of 7 permanent colours It will be a better solution to buy the single colour tape Specifications Waterproof DIY LED Tape Kit User Manual
5. re and heat shrink tube Step 1 Preparation Ensure the surface you are attaching to is clear of dust and dirt Clean thoroughly and leave to dry before fitting the tape Step 2 Connecting IR Controller Connect the 4pin connector to the control box and then to the LED tape FIG 1 Plug in the power supply and use the IR remote control to select the various functions Fig 2 Unravel the tape to check that all the LEDs are functioning correctly If there are any faults return to your retailer without delay FIG 1 IR Receiver Control Box Connector LED Tape Power IN FIG 2 Static Static Red Static Blue White Static z Static TQ ing Orange Deep Blue ane mt Static Gradually Brown changing Static Deep Yellow Static Yellow Light Blue Static Pink Static Static Sky Static Light Yellow sme Step 2 Cutting WARNING Disconnect from the power supply before attempting any cutting Measure out each section and cut with sharp scissors only at the marked 10cm intervals Do not discard any excess tape as it can be easily reconnected and used again see FIG 4 Waterproof DIY LED Tape Kit User Manual NY fluxia Step 4 Fitting Clear the area you wish to install and remove the backing paper exposing the adhesive tape Push tape firmly onto the surface It is recommended to work on 50cm sections at a time in order to ensure a professional finish When you reach the end of your installation cu
6. t at the marked cutting point The tape can be terminated at highlighted 10cm cut intervals if less than 5m is required FIG 3 sang gate Cattng pomt awe wst O O poo boot pnopg bob op aoa O Do w You may also reconnect the two pieces by soldering the point connections together The tape has 4 tracks for the DC voltage Common indicated as 12V on the tape Green Red and Blue To re attached use a craft knife to cut the Epoxy coating from the terminals Use a soldering iron and solder to connect the DC wire to the relative terminals be sure not to cause a short circuit in the process as it will not work FIG4 WARNING Only cut the tape on the highlighted intervals Cutting the tape in other parts without due care will permanently damage that section of the tape and will result in malfunction Points to remember when using this tape i O10 a 1 Only cut the tape at the highlighted 10cm intervals 2 Do not connect another reel and operate from a single power supply as this will seriously affect the performance 3 Ensure you connect the correct wires otherwise the tape will not work 4 Ensure that when soldering there are no short circuits 5 We recommend use of end caps or heat shrink tubing to protect the connection 6 Check that everything operates correctly before installing 7 Place the adaptor in a dry area where possible as even the tape is rated IP68 it does not apply to the adapt
7. ted ends are covered with end cap or heat shrink protected Q Can I clean the tape A Yes the tape is IP68 rated and has an epoxy coating Just wipe down with a damp cloth regularly to ensure continuing brightness Q Can I replace patch damaged tape with a new piece A Yes just highlight the affected area by the 5cm intervals Cut out the faulty section then fit in a new piece soldering the connections securely and use heat shrink to protect the repaired connection Specifications 12Vde LED Spacing 16mm Cut intervals 140 160 SMD3528 IP68 Waterproof DIY LED Tape Kit User Manual NY fluxia LED DIY TAPE KIT RGB MULTI COLOUR Introduction Thank you for purchasing the Fluxia DIY RGB LED Tape LED tape is ideal for use on the underside of a counter tops shelves cupboards around window frames or in an alcove of a ceiling to name just a few examples With IP68 rating allows the tape to be highly waterproof against water splashing or even under poor rain condition Before starting please ensure that you have read this instruction leaflet carefully If you are unsure about anything please have the tape installed by a competent installer Contents 1 x 5m reel of RGB LED tape 1 x Power supply with 3 region adaptors UK EU amp Worldwide 1 x Control Box with IR remote handset 15 x Clips 30 x Screws 3 x Endcap Possible required tools Scissors Craft knife Soldering iron and solder 4 core DC wi
Download Pdf Manuals
Related Search