Home

Multi-Loader Parameter writer Instruction Manual PWU003Z

image

Contents

1. Figure 3 Figure 4 For both these methods the SD card is recognized as an external storage device The SD card operates in Windows operating system explorer using the same copy paste actions as any standard external storage media OS Windows XP Vista 7 operating system Note Windows is the registered trademark of Microsoft Corporation in U S A and other countries The PC must be on and operational before connecting the Parameter writer to avoid an incorrect start up of the PC The SD card must not be removed when the Parameter writer is on and a transfer is in progress Otherwise data on the SD card may be lost The file name length is 255 letters maximum The number of files that can be saved in the SD card is up to 65535 or less N B Too many files cause slow key operation response and display Number of files should be little The following priority rules come into play when the Parameter writer is connected to a PC If no transfer is in progress between the Parameter writer and the drive the connection to the inverter is ignored and the Parameter writer is detected by the PC If a transfer is in progress between the Parameter writer and the inverter the user has to wait until the transfer is complete The Parameter writer must then be reconnected so the PC can detect it Source of configuration files If a inverter s configuration is to be duplicated it is copied to another inverter via the Parameter writer
2. Battery Charge level This menu displays the Parameter writer charge level Battery Alarm level This menu is used to set message activation at a particular charge level It warns the user about the battery charge status according to the set value see message fault detected on section 6 7 Battery Set battery type This menu is used to select the type of battery used by the Parameter writer normal batteries or rechargeable batteries Users must ensure that the correct battery type is selected so that the Parameter writer can accurately display the charge level This also affects message activation Parameters e e a 8 a 8 Bei tex y Batt tery ra Charge level dikzio gt Alarm level Se t battery type e i ERRA o te m Press and hold the up Y or down arrow key to y esc y esc Charge level define this level value Alarm level gt Set battery type EE 70v more quickly 20 Normal Value between Alarm level E e Set battery type sc E 0 and 50 NN Rechargeable Save the level Save the battery type TOSHIBA E6581680 6 7 Parameter settings Diagnostics The diagram below shows the Parameters Diagnostic menu accessib
3. 6 T Parameter writer main mella ceca ce aerae Ces aevo AEE 16 6 2 Action Load configuration from Parameter writer to inverter sees 17 6 3 Action Load configuration from inverter to Parameter writer 18 6 4 Quick SIOre mode eie Exi Mn eee ina Mo EE ets due cvs cce dea Mo vue rte due cuv UcMo ud ut dde E qux uve TE dum cuu eR 19 Bea GENS ORAA 20 6 6 Par meter settings ZE Aug AAE 21 6 7 Parameter settings Sl le Lula DEO lerr 22 6 5 Parameter settings PASSWOMG AAA 23 6 9 Parameter settings DIS DIA AAA 23 JEN ellieDvpeslm c 24 8 WARRANTY uero ee tiet EI E EE 24 TOSHIBA E6581680 1 Setup procedure Thank you for purchasing Parameter writer PWUOOSZ for TOSVERT series inverters Before using Parameter writer carefully read this instruction manual in order to completely and correctly utilize Parameter writer s excellent performance After reading this instruction manual please keep it handy for future reference 1 Receive and inspect the Parameter writer Check that the reference printed on the label is the same as that on the purchase order Remove the Parameter writer from its packaging and check that it has not been damaged in transit 2 Connect the Parameter writer see chapter 4 ToaPC To an inverter 3 Copy inverter configurations see chapter 5 Load a configuration onto
4. Parameter writer to the inverter The inverter is in parameter read Bad transfer to the inverter the Wrong reference Fault CoMguration destination inverter No device connected incorrectly connected No file selected file selected is not compatible with the The inverter is not connected or is No configuration file is selected There is no file present on the SD card Check the RJ45 cable and both of its connectors Make sure the connection is secure for the duration of the transfer Restart the transfer operation Confirm the inverter parameter setting Check that the configuration file is compatible with the inverter to be configured Check the RJ45 cable and both of its connectors Make sure the connection is secure for the duration of the transfer Connect the RJ45 cable Select a file to transfer Follow the procedure for loading configuration files described on section 5 1 Check that the SD card is inserted correctly SD card fault The card b not recognized Check that the SD card is formatted correctly SD card Write protected The SD card is locked Check if the SD card is locked 22 TOSHIBA E6581680 6 8 Parameter settings Password Parameters Password FW For factory use only 6 9 Parameter settings Display The diagram below shows the Parameters Display menu accessible from Main menu Parameters Display Contrast This menu is used to s
5. See Loading a configuration from inverter on section 5 1 and Configuration transfers on section 5 2 and 5 3 11 TOSHIBA E6581680 4 2 Connection to an inverter Parameter files can be transferred to the inverter in whichever A and B condition A When the inverter is off the Parameter writer is powered B When the inverter is on the Parameter writer is powered by the inverter via the RJ45 cable Connect the Parameter writer to the inverter as following procedures 1 Insert the Parameter writer s communication cable into the inverter s RJ45 communication port Refer to the inverter s installation manual for more information about how to perform this task 2 Perform the desired transfer 3 Remove the Parameter writer communication cable from the inverter 1 Remove all power from the inverter and all enclosures housing the inverter and wait more than 15 minutes and more to allow the DC bus of the inverter to discharge 2 Insert the Parameter writer s communication cable into the inverter s RJ45 communication port Refer to the inverter s installation manual for more information about how to perform this task 3 Install and close all covers and doors before applying power to the inverter The inverter must be powered on before performing an upload or download 4 Perform the desired transfer 5 Upon completing the transfer remove all power from the inverter and the enclosures housing the inverter and wait 1
6. given by way of example only to symbolize an inverter All bold text in the manual e g Main menu Action corresponds to the messages displayed on the Parameter writer screen TOSHIBA E6581680 3 Receipt of the Parameter writer Product reference Check that the product reference printed on the label is the same as that on the delivery note This should also correspond with the number on the purchase order Contents of the Parameter writer box PWU003Z Check that the Parameter writer box contains the following 1 Parameter writer 2 SD card 3 Standard USB type A to Mini B cable 4 RJ45 RJ45 RJ45 cable Length 1m 5 Carry case 6 User s manual Japanese and English 7 Impact resistant cover 8 Wrist strap TOSHIBA E6581680 3 1 Presentation TOSHIBA mm Figure 1 Approximate weight 250 g including batteries TOSHIBA E6581680 3 2 Description a 00 LO 72 Figure 2 The connection between the Parameter writer USB A Mini B USB connector Mini B type and the PC USB type A is via a 1 m 3 28 feet USB type A to Mini B cable The connection between the Parameter writer and the RJ 45 connector inverter is via a RJ45 cable to load and transfer configuration files or updated application RJ connector with label cover connector with label RJ 1 connector with label cover For factory use only 00 For factory use only 00 use only itu card slot The SD card r
7. l 1 T 1 I ij T 1 I ij I I IC Y STOLE COMELG Y Successful Device 4 FilenameX EO l T FilenameX LSS SES SS e FilenameX 3 Page 16 ZEGOE COMELG Device n Successful LEE LSS SSS SS gt Store contig Suueeessa Turn the Parameter writer on using the ON OFF button F see section 3 2 Connect the Parameter writer to the inverter using the RJ45 cable see section 4 2 Press ENT when the screen displays Main menu Action Press ENT when the screen displays Action Config MLD Device Select the file to be transferred using the arrow keys and press ENT to start the transfer If no inverter is connected a message No device connected appears on the screen see section 6 7 The configuration has been transferred successfully from the Parameter writer disconnect the RJ45 cable from the inverter Connect the Parameter writer to the next inverter then press the Quick Store key e Store Config Successful The configuration has been loaded successfully onto the second inverter remove the RJ45 cable from the inverter his action can be carried out as many times as necessary Note Keep on pushing ESC key if the process of searching communication mode is canceled Display is changed faster by keeping on pushing A Or v key 15 T
8. n eso OFF Bah aie Deutsch Value between I Value between a wv 0 and 100 1 and 60 min gt Save the backlight eso Language Espanol em Save the language TOSHIBA E6581680 7 Specifications Specifications pwuoosz Applicable model VF nC3 or successor Note Applicable OS Windows XP Windows Vista or Windows 7 Communication setting automatic detection Communication Communication baud rate 4800 9600 19200 38400 bps setting Parity Non Even Odd parity Communication scheme R8485 Applicable batter 4 x LR6 AA alkaline batteries or id y 4 x NiMH rechargeable batteries Indoor operation at an altitude of 1 000m or less and free from direct sunlight Service environment potentially corrosive or explosive gases steam dust particles dust dirt and machining fluids including grinding liquid and coolant Protective method IP20 Ambient temperature 10 to 50 C Storage temperature 25 to 65 C Relative humidity 20 to 93 free from condensation and vapor Note Update is needed this product s software for future inverters 8 Warranty Any part of the unit that is proved to be defective will be repaired free of charge under the following conditions 1 This product will be repaired free of charge if problem fault occurs under normal handling within one year of delivery and is caused obviously by a design or manufacturing defect 2 The warranty applies
9. t do it What is prohibited will be described in or near the symbol in either text or picture form Indicates an instruction that must be followed Detailed instructions are described in illustrations and text in or near the symbol Indicates caution What the caution should be applied to will be described in or near the symbol in either text or picture form Indicates warning What is warned will be described in or near the symbol in either text or picture form TOSHIBA E6581680 Bl Limitation of use A Safety precaution E Never use this unit with any inverter other than TOSVERT series inverters Doing so may cause an accident E Handling in general AWarninc S Never disassemble modify or repair the product Disassembling the product may cause electric shocks fire or injuries Never M For repairs call your sales repair agency Disassemble Do not put or insert foreign objects such as waste cable bars or wires into the product It may lead to electric shocks or fire Prohibited Do not splash water over the product and do not wipe the body with a wet cloth It may lead to electric shocks or fire Turn off input power before wiring Wait at least 15 minutes and check to make sure that the charge lamp on the inverter unit is no Mandatory longer lit action Turn off the power immediately in case of any abnormalities such as smoke smell or abnormal noise Neglect of these conditions may lead to fire Fo
10. the inverter using the RJ45 cable see section 4 2 Press ENT when the screen displays Main menu Action Press ENT when the screen displays Action Config MLD Device e Select the file to be transferred using the arrow keys and press ENT to start the transfer see section 6 7 e he configuration has been transferred successfully from the Parameter writer Disconnect the RJ45 cable from the inverter Pressing ENT returns the user to the Action Config MLD gt Device menu Note Keep on pushing ESC key if the process of searching communication mode is canceled Display is changed faster by keeping on pushing A Or v key 14 TOSHIBA E6581680 5 3 Transferring the configuration to more than one inverter using Quick Store This procedure describes how to use the Quick Store function see section 6 4 to duplicate configurations The user must already have Loaded the inverter configuration file CFG onto the Parameter writer see section 5 1 OR Generated the configuration file using PCM software and loaded this file onto the Parameter writer filename1 filename 2 etc Main menu 1 Accion Action Contig MLD gt Device Store confi Successful MLD gt Device Filenamel MLD Device MLD Device Y d Filename2 FilenameN STOLE comi ig Device 3 enn ZA enn vy BAREAK I I I
11. 5 minutes to allow the DC bus of the inverter to discharge 6 Remove the Parameter writer communication cable from the inverter 12 TOSHIBA E6581680 5 Configuration transfers 5 1 Loading a configuration from an inverter This procedure allows the user to retrieve a configuration file LOADFRMDOO CFG to LOADFRMD99 CFG from an inverter and load it onto the Parameter writer s SD card Main menu 1 Action em tion Contig D gt Device v Action Contig Device gt MLD m AGELOM Comi XXXXXXXX Y Device MLD LoadFrmDxx cfg LoadFrmDxx cfg enn LoadFrmDxx cfg LoadFrmDxx cfg XX uuu Turn the Parameter writer on using the ON OFF button F see section 3 2 Connect the Parameter writer to the inverter using the RJ45 cable see section 4 2 Press ENT when the screen displays Main menu Action e Select the Action Config Device gt MLD menu using the arrow keys and press ENT Device gt MLD LoadFromDevicexx appears on the screen Press ENT until the transfer starts Load Config Successful The configuration has been loaded successfully onto the Parameter writer disconnect the RJ45 cable from the inverter The inverter configuration file filexx CFG is now loaded onto the P
12. OSHIBA E6581680 6 Parameter writer menus 6 1 Parameter writer main menu On power up the Parameter writer Version x x menu is displayed on the screen The diagram below shows the various menus that can be accessed from the Parameter writer main menu Main menu Action accesses the following functions Load from Parameter writer to inverter Load from inverter to Parameter writer Main menu Device accesses the following information Device type Device version Main menu Parameters accesses Battery parameters Diagnostic parameters Password parameters Display parameters Main menu About MLD accesses Parameter writer version information The Quick Store key see section 3 2 allows the user to transfer the most recent configuration file or update the inverter see section 6 4 for deda Multiloader Quick Store Version 3 04 About 2s Main menu r4 Main menu GO Main menu r4 Main menu Po ed Action Peri ge E Parameters D MLD Loo e Size vw vw vw v e C e ej o d Y bd O l v s9 y PO b Action Config Page 20 Parameters Build 03 04 MLD gt Device A gt Page 17 Battery gt Page 21 dd mm yy hh mm
13. TOSHIBA E6581680 Multi Loader Parameter writer Instruction Manual PWU003Z Notice Make sure that this instruction manual is delivered to the end user of the inverter Read this manual before first using the communications function and keep it handy as a reference for maintenance and inspections All information contained in this manual are subject to change without notice Please confirm the latest information on our web site www inverter co p TOSHIBA E6581680 Safety precautions On the inverter and in its instruction manual important information is contained for preventing injuries to users damages to assets and for proper use of the inverter Read the instruction manual attached to the inverter along with this instruction manual to completely understand the safety precautions the symbols and indications shown below Please adhere to the contents of these manuals at all times Explanation of markings Meaning of marking Indicates that errors in operation may lead to death or serious injury Indicates that errors in operation may lead to injury 1 to people or that these autio errors may cause damage to physical property 2 Such Sd as injury burns or shock that will not require hospitalization or long periods of outpatient treatment 2 Physical property damage refers to wide ranging damage to assets and materials Meanings of symbols Meaning of marking Indicates prohibition Don
14. arameter writer s SD card Pressing ENT returns the user to the Action Config menu Note elf a configuration file has already been loaded 100 files onto the Parameter writer s SD card it will be overwritten by the new configuration file from 101 files Renaming the file on the SD card via a PC connection means that the user can store more than one file on the SD card file CFG can be renamed as file1 CFG 13 TOSHIBA 5 2 Transferring the configuration to an inverter This procedure allows the user to select the configuration file to be transferred to the inverter The user must already have Loaded the inverter configuration file CFG onto the Parameter writer see section 5 1 OR Generated the configuration file using PCM software and loaded this file onto the Parameter writer 1 Main menu ACELOR 1 Action COME LG gt MLD gt Device Action Conti XXXXXXXX MLD Device MLD Device MLD gt Device Filenamel E Filename2 E FilenameN e e e Y FilenameX 2222 FilenameX EE E E E Y FilenameX gt gt gt gt gt gt gt gt gt gt gt gt Y Store config 3 m Successful Procedure Turn the Parameter writer on using the ON OFF button F see section 3 2 Connect the Parameter writer to
15. copied data cannot be written correctly Do not copy data from Parameter writer to inverter and inverter to Parameter writer while the inverter is running Some of the parameters cannot be written when the inverter is in operation When a copying operation is executed between two inverters with different capacities some of the parameters that vary with the capacity of the inverters will also be copied Therefore when copying the parameters between inverters with different capacities or voltage class the type information parameters of the inverter should always be initialized See the inverter instruction manual on how to initialize their parameters TOSHIBA E6581680 Contents GENEAN Nak aek aea 1 I RENE 5 2 INTRODUCTION AAE 6 3 RECEIPT OF THE PARAMETER WRITER suren 7 59 NM Sa agia ela AAA 8 22 BZ ei dia TOM et ess 9 4 CONNECTING THE PARAMETER WRITER e eern nnne nana anna nua a aane ena a aaa a aaa R aa aaa a aa ERR aaa aaa S RR RuuA 11 4 T Connection to a eTA 11 4 2 Connection to an Ada i uio n Crue emer accu cei os ci ca ais eee Dru e as 12 5 CONFIGURATION TRANSEEHG iier eatea aa 13 5 1 Loading a configuration from an inverter suna 13 5 2 Transferring the configuration to an inverter ee eeen 14 5 3 Transferring the configuration to more than one inverter using Quick Store 15 6 PARAMETER WRITER MENUS aa a Ua ceeds d Ursa eu bene nausea 16
16. e SD card Please be forewarned that our company cannot make compensation for the damage depend on the loss of the stored data Mandatory action E Disposal A Caution E f you dispose off this unit have it done by a specialist in industrial waste disposal Improper o disposal may result in explosion of capacitors or produce noxious gases resulting in injury Mandatory Persons who specialize in the processing of waste and known as Industrial Waste Product action Collectors and Transporters or Industrial Waste Disposal Persons If the collection transport and disposal of industrial waste is done by someone who is not licensed for that job it is a punishable violation of the law Laws in regard to cleaning and processing of waste materials B Notes on operation Avoid using in a place where ambient temperature or and humidity change sharply Keep the transmission cable separate from the power cable of the inverter to prevent the inverter from malfunctioning due to electromagnetic noise The integrity of data storage is guaranteed for up to 5 years The operating life of the data storage inverter is 10000 operations Do not execute more than 10000 writing operations Do not turn off power or remove the connection cable between the inverter and Parameter writer or take off SD card while a copying operation is in progress If the inverter power is turned off or the connection cable is removed while parameters are being
17. eceives and stores the files One SD card is supplied with the Parameter writer E Bater compartment It can take 4 normal batteries and rechargeable batteries E Power ON OFF button Press for 2 seconds to turn the tool on or off for 2 seconds Press for 2 seconds to turn the tool on or off turn the tool on or off EEM NM Ee a ee TOSHIBA E6581680 Data storage One SD card is supplied with the Parameter writer Any standard SD card and SDHC card are compatible with the Parameter writer SD card is used in this instruction manual for explanation The SD card format must be FAT32 Language The menus are in English Japanese Spanish German Italian and French Default language is set to English Power supplies Two kinds of batteries are available for powering the Parameter writer 4 x LR6 AA alkaline batteries batteries not attched NiMH rechargeable batteries batteries and charger not attched Battery life Depending on the type of batteries used the Parameter writer can transfer up to 300 configuration files Power save feature To prolong battery life a sleep mode is activated within a programmable time delay the Parameter writer is reactivated by pressing the ON OFF button See the display parameters menu on section 6 9 Connection to a powered up PC or inverter can also help conserve battery power as the power supply from the connected inverter takes over from the batteries Q Do not use n
18. either of the Action Config MLD gt Device menus Quick store XXXXXXXX No E No device eu connected No No File No SD euz present on the SD card Fault Page 17 Y Store config Exit Quick Successtul Store mode Jen Main menu Bet 1 619 Ce Note 1 Quick Store mode can only be used after an initial transfer to an inverter has been completed Files can only be transferred between inverters with the same reference 19 TOSHIBA E6581680 6 5 Supervision The diagram below shows the device main menu accessible from Main menu Device This supervisory menu is used to check the reference and version of the inverter connected to the Parameter writer Device Type This menu accesses the reference of the connected inverter Device SW version This menu accesses the software version of the connected inverter Main menu Device li i gt i Device Device Type SW Version Device No No Device connected connected bo d Type SW Version Esc AXXXXXXXXXX XXXX y No device connected es TOSHIBA E6581680 6 6 Parameter settings Batteries The diagram below shows the Parameters Battery menu accessible from Main menu Parameters
19. et the display screen contrast Display Backlight This menu is used to set the display screen time OFF ON 1 to 5 seconds are selected Display Sleep mode This menu is used to set the Parameter writer s sleep mode Display Language This menu accesses the language selection for the Parameter writer interface Parameters Display E a E D E a a Display GEEAE esc Display gt Backlight Display gt Sleep mode Display gt Language e Se e Yo 8 E ue mg bezen OR Set contrast Set backlight Set sleep mode pees 50 3 sec 05 mn English b Q a Set sleep mode S EE i Set backlight NN 2 sec 5 av Language NN mn H ANGE enm 9 Q La ALA Ae 23 IK GE A Save the contrast Set backlight Save the sleep mode Language E 1 sec Francais Set backlight EEEa eso Press and hold the up SN Press and hold the up Italiano or down arrow key to or down arrow key to define the contrast A vy define the sleep mode a e value more quickly value more quickly Set backlight
20. ickel cadmium rechargeable battery or manganese battery This may lead to liquid spill and fire Mandatory It is not possible occasionally to read according to the kind of the SD card and record condition action It is not warrantable operation and the power supply for all SD cards The specification of the SD card might be changed for reasons of manufacturer s own It is not possible occasionally to operate normally according to the changes Even if it is the same type form the specification might be different in each selling area according to the SD card The data file recorded except the specified format might not to be able to read normally and not displayed the file name The SD card with the security function cannot be used The described specification might change without notice E E E E E E E E 10 TOSHIBA E6581680 4 Connecting the Parameter writer This section describes the various ways of connecting the Parameter writer Default language is set to English Refer to section 6 9 and change the language setting according to need 4 1 Connection to a PC There are two ways of storing files on the SD card Insert the SD card in the Parameter writer and connect the Parameter writer to the PC via the standard USB type A to Mini B cable see Figure 3 OR Insert the SD card in the SD card reader on the PC see Figure 4 A USB type A connector B USB Mini B type connector SD card reader
21. le from Main menu Parameters Diagnostic Fault History This menu accesses the detected fault history Diagnostic Clear Faults This menu is used to clear the detected fault history Parameters Diagnostic S D Diagnostic S Fault History e Diagnostic rault 1 D Diagnostic fault2 a E Diagnostic Taol See the table of faults codes below E Clear Diagnostic itenulte Ace YOU SUE TO clear faults List of cleared e Clear faults History done b faults codes Parameter writer display Probable cause Warning The battery charge is low The appearance of this message depends on the charge Low Battery Level level defined by the user See setting the detection section 6 6 Make sure you have a set of replacement batteries to hand as the current set have little life left The battery charge is too low Replace the batteries immediately No more Switch off Low battery The Parameter writer will turn off transfers can be made Incomplete or incorrect transfer to the Store config fault inverter prohibition state The inverter is in parameter change Incomplete or incorrect transfer from Load config fault prohibition state the
22. only to the delivered unit 3 For the following kinds of failure or damage the repair cost shall be borne by the customer even within the warranty period i Failure or damage caused by improper or incorrect use or handling or unauthorized repair or modification of the inverter ii Failure or damage caused by the unit falling or an accident during transportation after the purchase iii Failure or damage caused by fire salty water or wind corrosive gas earthquake storm or flood lightning abnormal voltage supply or other natural disasters iv Damage due to the use of Parameter writer for non intended purposes 4 f an additional warranty is provided then those conditions will also apply 24
23. ore No mode Note Keep on pushing ESC key if the process of searching communication mode is canceled Display is changed faster by keeping on pushing A Or v key 17 TOSHIBA 6 3 Action Load configuration from inverter to Parameter writer The diagram below shows the Action Config Device gt MLD menu accessible from Main menu Action Action Config Device gt MLD This menu accesses the transfer function for loading configurations from the inverter to the Parameter writer Transfer in progress Note Keep on pushing ESC key if the process of searching communication mode is canceled Or v key Action Config Device gt MLD Device connected Yes Device gt MLD LoadFrmD00 cfg E6581680 No device connected Write protected SD carel Fault Jem LoadFrmDxx cfg WES LoadFErmDxx ctfg Y LoadFrmDxx cfg SS E EE EE E EE E Y Transfer complete E Load config Suceessiul Load config Fault e Display is changed faster by keeping on pushing A 18 TOSHIBA E6581680 6 4 Quick Store mode This mode is used to transfer the latest configuration file See section 5 2 1 The diagram below shows the Quick Store mode which can be accessed after using
24. r repairs call your sales repair agency E Transportation and usage A Warninc Do not install or operate the inverter if it is damaged or any part of it is missing Operating a defective inverter may lead to electric shocks or fire Prohibited For repairs call your sales repair agency Do not put any flammable material near the product It may catch fire due to the product sparking in the case of a malfunction Do not connect a LAN cable or telephone modular cable to Parameter writer Doing so may cause a failure or accident o Electrical construction work must be done by a qualified expert Connection of input power by someone who does not have expert knowledge may result in fire Mandatory or electric shock action Operate under the environmental conditions prescribed in the instruction manual Operations under any other conditions may result in malfunction An emergency stop inverter must be installed that fits with system specifications e g shut off input power then engage mechanical brake Operation cannot be stopped immediately by the inverter alone thus risking an accident or injury Use the attached cable for connecting this optional unit The use of any other option may result in an accident ACaution Q WV Do not use the product in any place subject to vibrations or it may fall This may lead to the product falling and causing injury Prohibited V Do not use nickel cadmium rechargeable battery or manganese battery Thi
25. s may lead to liquid spill and fire V Do not use different type of battery together or new battery and reuse one together This may lead to liquid spill and fire TOSHIBA E6581680 E Operations A Warninc V Do not apply a dropping shock or other physical shocks Otherwise damage or malfunction will result Prohibited E Do not pull on the cable and connector It may cause damage or error E Do not bring any regions of your body into contact with the inverter terminals when power is supplied to the inverter Contact during the power on status of the inverter can result in electric shock Q Use an additional safety inverter with your inverter or system to prevent a serious accident due to the unit malfunctions Usage without an additional safety inverter may cause an accident Mandatory Make sure to check that the parameter data from this product is not accidently copied to the action wrong inverter Usage with wrong parameter may result in an accident A Caution W Set up Communication time out F GOZ F GO and F A GAY see the inverter instruction Q manual for details to stop the inverter when Parameter writer is deactivated by an unusual event such as tripping an operating error power outage failure etc Deactivated Parameter writer may cause an accident if the Communication time out is not properly set up Please back up the data used with this unit The stored data might be lost according to using condition of th
26. the Parameter writer Transfer a configuration to an inverter Transfer a configuration to several inverters Quick Store 4 Parameter writer menus see chapter 6 TOSHIBA E6581680 2 Introduction The Parameter writer PWUOOSZ is a standalone tool for transferring configuration files to inverters with their power on or off The Parameter writer is used to set inverter parameters by loading a configuration file onto the inverter s Inverters must have the same reference If the reference is not the same the fault occurs before the data is transfered The parameters can be set with them before they are powered up Duplicating or generating configuration files A Gontigungiion dupka 1 Taner fo one device 2 Tranter to several devices using Quick Sinne A The inverter s configuration file is copied to the Parameter writer s SD card See the procedure on section 5 1 B The configuration file is generated by PCM software then transferred to the Parameter writer s SD card See the procedure on section 5 1 1 The user selects and then transfers the configuration file from the Parameter writer to the inverter See the procedure on section 5 2 2 Once the initial transfer is complete the user can use Quick Store mode which allows the Parameter writer to load the same update file on several inverters in succession See section 5 3 All representations of the VF nC3 inverter throughout this document are
27. v E e E Berion Comi ig Peremeterg Device gt MLD a gt Page 18 Diagnostic A gt Page 22 A vt 9 A Berion Pash For facto Parameters Firmware p EZ Password FW Page 23 Parameters Display es Page 23 16 TOSHIBA E6581680 6 2 Action Load configuration from Parameter writer to inverter The diagram below shows the Action Config MLD gt Device menu accessible from Main menu Action Action Config MLD gt Device This menu accesses the transfer function for loading configurations from the Parameter writer to the inverter Main o menu Action Conto gt MLD gt Device A A A re No device connected Device connected SD Carel Fault Yes MLD gt Device MILD 2 DEWILeES t MLD Device y 5 Filenamel p Filename2 FilenameN e E amp E e E Y The file is saved FilenameX lt e Quick for Quick Store gt gt gt gt Store mode Y FilenameX por Transfer in progress Y FilenameX pon Wrong reference ENT or ESC Incorrect configuration enn esc Cancel to transfer file for this device configuration Y SEOre COnNFLG STOre EGOEREI Store config Successful Successful fault Page19 Yes Quick st

Download Pdf Manuals

image

Related Search

Related Contents

Philips HR1830/00  PX 738 - Qlima  CB M TACd2 Manuel d`installation Boîtier de contrôle  入札説明書 - 国立水俣病総合研究センター    Istruzioni d`uso e di installazione Lavatrice PW 5065  Kontron User's Guide «  Art Editions  MGP 464 - Extron  Samsung RSH1DTPE manual de utilizador  

Copyright © All rights reserved.
Failed to retrieve file