Antik EX 5108 Encoder MANUAL
Contents
1. Gigabit Out Switch ON OFF to switch on off the current channel MUX ASI Out set the source for IP output channel MUX ASI Out ASI 9 Mode Multiple IP Board IP Gigabit Address set the IP address of the IP port Output Address 10 10 80 60 IP Board Net Gigabit Subnet Mask set the net mask of the IP port Mask 255 255 255 0 IP Board Gigabit Gateway set the gateway of the IP port Gateway 10 10 80 1 Gigabit MAC Address display the MAC address of IP Board MAC Address the IP port Protocol Gigabit Local UDP set UDP protocol to IP output Protocol UDP RTP set RTP protocol to IP output TS Pkts Per UDP set the number of TS packets that can be carried by each UDP packet valid range from TS Pkts Per UDP 7 1 7 TS IP Gigabit Time To Live set TTL to the output IP packets valid Time To Live 255 range from 1 255 Type Of Service Min Delay Max Reliability Max Type Of Service Min Throughput Min Monetary Cost Normal Delay L5 www antiktech com MANTIK technology Gateway MAC Address set the MAC address of the Gateway MAC Address gateway under which the device is connected ff ff ff ff ff ff Gigabit Out Switch Enable Disable Gigabit Out Switch ON Protocol UDP set UDP protocol to IP output Protocol UDP RTP set RTP protocol to IP output TS Pkts Per UDP set the number of TS packets that can be carried by each UDP packet valid range from 1 7 TS Pkts Per UDP 7 Time To Live set TTL to2. Multicast Port 1236 6 Target MAC address loo loa 26 s5 12 67 6 Switch ion o E Channel 7 7 Uni Multicast IP za a lh If 7 Uni Multicast Port ze 7 Target MAC address o0 o0 26 56 12 67 7 Switch EL Rd Channel 8 8 Uni Multicast IP fz33 a lh s 8 Uni Multicast Port 1234 8 Target MAC address foo loo 26 lss 22 e7 8 Switch On a Channel 9 Mux ASI Out ES v 9 Uni Multicast IP lh Jh 9 Uni Multicast Port ze i S Target MAC address oo bo 26 55 12 le7 S Switch on MV 21 www antiktech com MANTIK technology Gigabit Output Under multiple output operation mode user can set output uni multicast IP addresses and port number for each encoder the built in remux and ASI input Each IP output channel can be switched ON OFF independently The source for TS IP output 1 8 is forced to link to the encoder 1 8 respectively and cannot be changed The source for the 9 uni multicast output channel can be the built in remux or ASI input Note the page below is displayed only when the TS IP operation mode is Multiple Output mode To change the TS IP operation mode please refer to chapter 8 5 System Device Gigabit Input Under Multiple output mode the Gigabit Input is not available Local Settings Set the parameters for the TS IP output port Gigabit Address set the IP address of the IP port Gigabit Subnet Mask set the net mask of the IP port Gigabit MAC
3. 264 HD SD Encoder This User Manual is written for operators users of the EX 5108 to assist in installation and operation Please read this user manual carefully before installation and use of the device FOR YOUR SAFETY This equipment is provided with a protective earthing ground incorporated in the power cord The main plug shall only be inserted in a socket outlet provided with a protective earth contact Any interruption of the protective conductor inside or outside the device is likely to make the device dangerous Do not remove the covers of this equipment Hazardous voltages are present within this equipment and may be exposed if the covers are removed Only Beijing Jaeger trained and approved service engineers are permitted to service this equipment The supplied AC power cable must be used to power the device If the power cord becomes damaged it must be replaced No operator serviceable parts inside Refer servicing to Beijing Jaeger trained and approved service engineers For the correct and safe use of the device it is essential that both operating and servicing personnel follow generally accepted safety procedures in addition to the safety precautions specified in this manual Whenever it is likely that safety protection is impaired the device must be made in operative and secured against unintended operation The appropriate servicing authority must be informed For example safety is likely to be impaired if the device fails to pe
4. Address display the MAC address of the IP port cannot be modified by user Gigabit Gateway set the gateway address under which the IP port is connected Gateway MAC Address set the MAC address of the gateway under which the device is connected this is necessary when the IP streaming is needed to pass through the gateways Status ts ip mux Gigabit Out Gigabit In Gigabit Local E Gigabit Local Gigabit Address Gigabit Subnet Mask Gigabit MAC Address Gigabit Gateway Gateway MAC Address Full duplex Output Mode Encoder System Gigabit Local 10 lho fio ho 255 255 255 0 00 50 22 00 22 67 10 lho j110 lji The pages below are displayed under Full duplex mode To change the TS IP operation mode please refer to chapter 8 5 System Device 22 www antiktech com MANTIK technology Gigabit Input Under full duplex operation mode the device supports single uni multicast reception Set the uni multicast target IP address and port number in the page Status TS IP MUX System Encoder l Gigabit Out Gigabit In Gigabit In Gigabit Local Gigabit In Uni Multicast IP Address 224 1 1 1 1 Uni Multicast UDP Port 1234 TS Clock Recovery Auto v Uni Multicast IP Address set the multicast address for the incoming IP streaming To receive a unicast streaming the submenu can be ignored Uni Multicast UDP Port set the port number for the incoming IP streaming TS Clock Recover Auto it is s
5. FPGA LINUX OS Edit Login ID press Enter and key in the login ID WEB Login ID Default Login ID root for WEB management Edit Login Password press Enter and key in the Default Login Password WEB Login Password password for WEB management 12345 www antiktech com 17 Gigabit Mode Gigabit Mode MANTIK technology Multiple Output the IP I O is configured as multiple uni multicast output mode which delivers up to 10 streams over IP There are 8 stuffed or un stuffed SPTS lower bit rate but less PCR accurate than normal SPTS from local encoders and two MPTS Gigabit Mode Output Multiple from built in remultiplexer and ASI input over the IP with different Unicast or Multicast IP addresses Full Duplex the IP I O is configured as full duplex mode which allows only one MPTS or SPTS over IP input and output in uni multicast at the same time 8 Control with Web Server EX 5108 has an integrated web server This web server allows the configuration and status requests with a standard web browser To operate a EX 5108 first make sure the Ethernet control port is well connected in the network and could be pinged by the host PC and then enter the IP address of the EX 5108 into the browser there will be a pop up showed asking for login user and password After login the device can be operated The default user name and password are respectively root and 12345 The username and passwo
6. Layer Il MPEG2 AAC LC MPEG4 AAC LC can be selected on EX 5108 series only Audio Bit Rate 32k bps 48k bps 56k bps 64k bps 80k bps 96k bps 112k bps128k bps 160k bps 192k bps 224k bps 256k bps 320k bps 384k bps Audio Channel Mode Stereo set stereo mode Mono set mono mode NOTE only Left audio channel will be encoded Audio Level 12dB 17dB set the gain of output volume Mute mute the output audio Audio SDI EMB the menu is displayed on EX 5108 S only EMB1 EMB2 EMB3 EMB4 select the group of embedded audio from input SDI signal Encoder Bit Rate 600 48000Kbps set the output bit rate of the selected encoder Note Encoder bit rate must greater than the sum of video bit rate audio bit rate PSI 150Kbps buffering 100Kbps encoder error 150Kbps Scale Disable video resolution is the same as input MANTIK technology Audio Format MPEG1 Layer2 Audio Bit Rate 128 Kbps Audio Channel Mode Stereo Audio1 Level 0dB Audio SDI EMB EMB1 Encoder Bit Rate 5000Kb s PMT PID set PMT PID valid range from 32 to 8190 Output PMT PID 43 mn Video PID set Video PID valid range from 32 to Output Video PID 4001 iene eee Audio PID set audio PID valid range from 32 to Output AudioPID 4002 Fe A PCR PID set PCR PID valid range from 32 to 8190 Output PCR PID 8004 cmt Pn Service PID set Service PID valid from 32 to 8190 Output Service PID 4000 anne ere Encoder Vide
7. MANTIK technology IP Address set the device s IP address Network Mask set the net mask of the device Gateway set the gateway address of the device MAC display the MAC address of the device cannot be modified by user Version User can check versions of various functional blocks of the device as it shown in figure below Status Ts 1P mux System Encoder Device 3 IP Control Version READ Main Version 5801EC000a Login Factory Default System Reboot Login Set the login ID and password for the web management server of the device 2 2 p Status Ts 1P mux System Encoder Device IP Control Version HTTP Login Login Factory Default Passwol System Reboot n Factory Default Click the button Default to restore the factory default settings to the device Note the IP address of the device and the operation mode of the Gigabit board will not be restored 28 www antiktech com MANTIK technology Status Ts 1P mux system Encoder Device IP Control Factory Default didi Press button Default to restore default settings Login Factory Default System Reboot System Reboot User can reboot this device by clicking the button Reboot Status TS IP MUX System Encoder Device IP Control System Reboot Poman Press button Reboot to restart the device Login Factory Default System Reboot 9 Installation It is highly recommended to fix the EX 5108 be mou
8. descriptors 26 www antiktech com MANTIK technology 8 5 System The system page gives all information of this device including device name serial number software version and so on User can implement the alarm switch configuration network settings TS IP operation mode and software upgrade under system page Device Status Ts 1P mux System Encoder Device IP Control Pevice Version Device Login Factory Default Device Label 5801EC_5 System Reboot Serial Number 0123456789abc WEB Auto Refresh Time Every 20 seconds vi TS IP Mode TS IP Mode Single channel Device Label Check the name and the serial number of this device User can resign this product name at will the device name should be less than 24 characters The serial number is read only Serial Number show the serial number for the device cannot be modified by user WEB Auto Refresh Time set the interval of webpage refresh Gigabit Mode switch the TS IP operation mode between Multiple Output and Full duplex The device will reboot after change IP Control The network settings for the device can be found and configured under the page below Status TS IP MUX System Encoder Device IP Control IP Control Version Local Settings Login eee Factory Default IP Address 10 10 80 J101 System Reboot Subnet Mask 255 255 255 o Gateway 10 10 ligo lji MAC Address 00 33 12 21 22 11 Cancel 27 www antiktech com
9. in fixed RTP frames TS IP Status Display IP link Status Multiple Link Status 10M 100M 1000M Disconnect Output 11 www antiktech com MANTIK technology 7 2 2 Configuration Sub menu no Description Factory Default Value Parameter Encoder Select Encoder 1 the encoder 1 is active for configuration Encoder 2 the encoder 2 is active for configuration Encoder 3 the encoder 3 is active for configuration Encoder Encoder Select Encoder 4 the encoder 4 is active for configuration Encoder 5 the encoder 5 is active for configuration Encoder 6 the encoder 6 is active for configuration Encoder 7 the encoder 7 is active for configuration Encoder 8 the encoder 8 is active for configuration Video Rate Ctl CBR set constant bit rate mode Video Rate Cil VBR VBR set variable bit rate mode Input Video Format 1920x1080i 29 97 1920x1080i 25 1440x1080i 29 97 1440x1080i 25 1280x720p 59 94 Encoder 1280x720p 50 720x480i 29 97 720x576i 25 Video Settings 1920x1080p 59 94 1920x1080p 50 Input Video Format 1920x1080i 29 97 Video Bit Rate 300 45000Kb s set the video bit rate Video Bit Rate 3000Kb s Aspect Ratio Aspect Ratio 4 3 4 3 set video aspect ratio to 4 3 16 9 set video aspect ratio to 16 9 12 www antiktech com Encoder 13 Audio Settings Encoder Bit Rate Advanced Settings Audio Format MPEG1 Layer2 set the audio compression format MPEG 1
10. range from 1 65535 ProMPEG FEC Switch Enable or Disable the ProMPEG FEC Note the submenus below are available only when the ProMPEG FEC is switched on and has be applied ProMPEG FEC Switch Enable 7 Column FEC UDP Port 2360 How FEL UDP Port 125 ProMPEG FEC Mode 1D SAS FEC Alignment Annex B x fest Drop Packets E ProMPEG FEC Mode select the mode of ProMPEG FEC from the dropdown list Column FEC UDP Port set the port number for column FEC Row FEC UDP Port set the port number for row FEC FEC Alignment set the alignment for FEC Test Drop Packets set the test drop packets 24 www antiktech com MANTIK technology Local Settings Set the parameters for the TS IP output port aao IM a oe Status TS IP MUX System Encoder Gigabit Out i i Gigabit In Gigabit Local Gigabit Local E a Gigabit Local Gigabit Address io jio j110 J10 Gigabit Subnet Mask 255 255 255 0 Gigabit MAC Address 00 50 22 00 22 67 Gigabit Gateway 10 j10 J110 1 Gateway MAC Address 00 00 l12 fo3 56 77 Gigabit Address set the IP address of the IP port Gigabit Subnet Mask set the net mask of the IP port Gigabit MAC Address display the MAC address of the IP port cannot be modified by user Gigabit Gateway set the gateway address under which the IP port is connected Gateway MAC Address set the MAC address of the gateway under which the device is connected this is necessary when the IP stream
11. the output IP packets valid Time To Live 1 255 range from 1 255 Type Of Service Min Delay Max Reliability Max Type Of Service Min Throughput Min Monetary Cost Normal Delay Gigabit Output Uni Multi Address 238 069 070 001 Uni Multi IP Address set the destination IP address Uni Multi UDP Port 01234 Uni Multi UDP Port set the destination port number valid range from 1 65535 TS IP Gigabit Mode Full Duplex ProMPEG FEC Switch Disable ProMPEG FEC Mode ProMPEG FEC Mode 1D 5x5 1D 5x20 1D 10x10 2D 5x5 2D 5x20 2D 10x10 FEC Alignment FEC Alignment ProMPEG FEC Switch Enable Disable o Gigabit Adress Gigabit Address set the IP address of the IP port 010 010 080 060 f Gigabit Subnet Mask Gigabit Subnet Mask set the net mask of the IP port 255 255 255 000 Gigabit MAC Address display the MAC address of o Gigabit IP Gateway Gigabit Gateway set the gateway of the IP port 010 010 080 001 Gateway MAC Address set the MAC address of the Gateway MAC Address gateway under which the device is connected ff ff ff ff ff ff ff Uni Multi Address set the uni multicast target Uni Multi Gigabit Input address of the IP input Uni Multi UDP Port set the target port number of the Uni Multi UDP Port www antiktech com 16 MANTIK technology TS Clock Recovery Gigabit Input Auto it is suggested to set Auto when there is accurate PCR carried by the inputted TS IP Fixed Rate whe
12. ASI Out 2 AC 90 250V Q 6 Front panel and rear panel instructions 6 1 Front panel A1 A1 Status LEDs Power green when power is on red when one of the power supply unit malfunction Warning red when function faulty Alarm red when function critical 8 www antiktech com A2 Encoder Status A3 VFD Panel A4 Keypad A5 USB A6 Management A7 TS IP 6 2 Rear panel of EX 5108 EX 5108 S B2 O Def 0000 MANTIK technology Encoder 1 8 working status green light indicates the corresponding encoder module is under working red when the corresponding encoder module malfunction or stop or input is invalid 6 keys for local control Used to upgrade software version of this device Ethernet 10 100 LAN control port TS over IP I O port B5 Alarm B1 B3 EX 5108 H J ASI in ASI Out 2 HDMI B4 B3 B6 B1 ASI IN B2 ASI OUT B3 Digital Audio Video IN B4 RS232 B5 Alarm B6 Power Socket ASI input interface 2 ASI output interface output in mirror SDI HDMI input interface Reserved for factory use Alarm relay interface AC Power Input www antiktech com MANTIK technology 7 Control with Front Panel With the keypad and display panel on the front panel user can configure the device locally 7 1 Overview of the Menu Power on the device and wait for initialization complete the Local IP address will be displayed on the VFD panel Press ENTER to get into the mai
13. MANTIK technology USER MANUAL EX 3108 8 Way H 264 HD SD Encoder Contents Notice Before Using the Device 1 Overview 2 Features 3 Technical Specifications 4 Ordering Information 5 Block Diagram 5 1 TS IP Full Duplex mode EX 5108 5 2 TS IP Multiple Output mode EX 5108 08 6 Front panel and rear panel instructions 6 1 Front panel 6 2 Rear panel 7 Control with Front Panel 7 1 Overview of the Menu 7 2 Description of menu 7 2 1 Status 7 2 2 Configuration 7 2 3 System 8 Control with Web Server 8 1 Status 8 2 Encoder 8 3 TS IP 8 4 MUX 8 5 System 9 Installation MANTIK technology Notices COPYRIGHT Copyright 2014 Beijing Jaeger Communication Electronic Technology Co Ltd Not to be copied used or translated in part or whole without Beijing Jaeger prior consent in writing except approval of ownership of copyright and copyright law WARRANTY This warranty does not cover parts which may become defective due to misuse of the information contained in this manual Read this manual carefully and make sure you understand the instructions provided For your safety be aware of the following precautions WARNING IMPORTATNT SAFETY INSTRUCTIONS CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL WARNING e To reduce the risk of fire or electric shock do not expose this apparatus
14. V Gigabit TS over IP Full Duplex Mode Standard IEEE 802 3 10 100 1000 Base T Full Duplex x 9 80Mb s UDP or RTP SPTS or MPTS ICMP ARP IGMPv2 Packet Length Number of Multi Unicast Max Effective Bit Rate Data Protocol Control Protocol www antiktech com MANTIK technology Front Panel Control 1xRJ 45 10 100 Base T TS IP 1x IP GbE RJ 45 10 100 1000 Base T Display 2 x 20 LCD Display 10 90 Non condensed 4 Ordering Information anao Me exson Exsis exstos s Exsios s DST RR o e w asi nc e e TS IP under full duplex mode ASI mirrored Output AAC4C Audio Support o dam fe e q Toe Cool RR RR RR RR EE Te www antiktech com MANTIK technology 5 Block Diagram with different applications 5 1 TS IP Full Duplex mode EX 5108 H S Function Block Diagram Full Duplex HD SDI In 1 HDMI In 1 HD SDI In 8 A HDMI In 8 A ASI Out 1 Keypad ansm t E ASI Out 2 O TS IP In amp Out www antiktech com MANTIK technology 5 2 TS IP Multiple Output mode EX 5108 H S Function Block Diagram Multi Channel HD SDI In 1 Cable Equalizer 1 HDMI In 4 HDMI Receiver TSAP Out 8xSPTS 1MPTS H 264 HD SDI In 8 Cable Equalizer 8 jui SD HD mm jp ms gt gt gt gt ASI In Keypad LCD LED Control RS 232 Alarm ASI Out 1 AC 90 250V O
15. ate Audio Channel Mode set the audio in stereo or mono NOTE only Left audio channel will be encoded when Mono mode is on Audio Level set the gain of output volume Audio SDI EMB select the group of embedded audio from input SDI signal the menu is displayed on EX 5108 S only Encoder Bit Rate set the output bit rate of the current encoder Encoder bit rate must greater than the sum of video bit rate audio bit rate PSI 150Kbps buffering 100Kbps encoder error 150Kbps valid range from 300 to 99999Kb s Advanced Setup PMT PID set PMT PID valid range from 32 to 8190 decimal Video PID set Video PID valid range from 32 to 8190 decimal Audio PID set audio PID valid range from 32 to 8190 decimal PCR PID set PCR PID valid range from 32 to 8190 decimal Service PID set Service PID valid from 32 to 8190 decimal Service Name set the service name for the encoded channel The length should be less than 24 characters Scale Enable or Disable the output video resolution rescaling The following two parameters have to be set manually if the Scale is enabled Scale Vertical set the resolution in vertical Scale Horizontal set the resolution in horizon 20 www antiktech com MANTIK technology 8 3 TS IP All models provide two TS IP operation modes The first is Full Duplex which allows one MPTS or SPTS inputted to make up a new MPTS with local encoders then sends the new one over IP amp ASI out In th
16. e second mode Multiple output which delivers up to five streams over IP There are four stuffed or un stuffed SPTS and one MPTS from internal reMultiplexer over the IP with different Unicast or Multicast IP addresses The management webpage will be different following the change of the operation mode Multiple Output Mode The pages below are displayed under Multiple Output mode To change the TS IP operation mode please refer to chapter 8 5 System Device Status tTs r mux System Encoder qu Gigabit Out Sora Channel 1 1 Uni Multicast IP oh o lh 1 Uni Multicast Port 1234 1 Target MAC address on ae 58 e 1 Swite on Channel 2 2 Uni Multicast IP FE lh Jh 7 2 Uni Multicast Port za 2 Target MAC address loo loo ze se 12 67 2 Switeh lon vi Channel 3 3 Uni Multicast IP ao as vi 2 3 Uni Multicast Port 1234 3 Target MAC address loo loo ze s6 12 67 3 Switeh lon v Channel 4 4 Uni Multicast IP z233 Jn lh le 4 Uni Multicast Port nza 4 Target MAC address loa o 24 lss 12 fe 4 Switch on s Channel 5 5 Uni Multicast IP z ia lh He 5 Uri Multicast Port 1234 gt Target MAC address loo loo 26 ss 12 67 5 Sw teh lon bd Channel 6 6 Uni Multicast IP z lh Ih le Uni
17. ere are eight encoders integrated on one EX 5108 each encoder can work independently Click on the Encoder 1 ig configure the encoder 1 the same for the rests Status Ts 1P mux System Encoder Encoderi Encoder2 Encoder3 Encoder4 Video 1 Setup Encoder5 Video Rate Ctl CBR v Video Format 1920x1080i 29 97 M Encoder6 Encoder 1 video Bit Rate Kbps 3000 Aspect Ratio 4 3 v Encoder7 Encoder8 Audio 1 Setup Audio Format MPEG1 layer2 v Audio Bit Rate 128kbps v Audio Channel Mode Stereo v Audio Level 0 dB v Audio SDI EMB EMB1 Encoder 1 Bit Rate Encoder Bit Rate Kbps 25000 Advanced 1 Setup PMT PID 2336 video PID 2304 Audio PID 2320 PCR PID 2352 Program Num 1024 Service Name Encoded Video 1 Scale Disable v Scale Horizontal 720 Scale Vertical 576 MANTIK technology Video Setup Video Rate Ctl set constant bit rate mode or variable bit rate mode for the selected encoder Input Video Format seleci the resolution for the encoded video in the dropdown list Video Bit Rate set the video bit rate The setting is valid only when the Video Rate Ctlis CBR Aspect Ratio set the aspect ratio for the encoded video 4 3 or 16 9 Audio Setup Audio Format set the audio compression format MPEG 1 Layer Il or MPEG2 AAC LC MPEG4 AAC LC can be selected on EX 5108 series only Audio Bit Rate set the audio bitr
18. esolution downscale at same frame rate SNMP amp HTTP WEB Redundant Power Supplies 19 x 1 U EIA standard chassis V VV VV YV V WV www antiktech com MANTIK technology 3 Technical Specifications Video input amp compression HDMI x 8 or HD SDI x 8 H 264 AVC HP L4 0 4 2 0 8 bit YCbCr Number of input ports Compression Standard Video Sampling Format Video Encoding Bit Rate 2 30Mbps for each channel 1080p 1920x1080 59 94 Hz 50 Hz SMPTE296M 6 30Mb s 1080i 1920x1080 D25Hz 29 97Hz 30Hz SMPTE274M 6 24Mb s Video Resolution amp 1080i 1440x1080 D25Hz 29 97Hz 30Hz SMPTE274M 5 24Mb s Recommended Bit Rate 720p 1280x720 D50Hz 59 94Hz 60Hz SMPTE296M 4 24Mb s 480i 720x480 29 97Hz SMPTE656M 2 10Mb s 576i 720x576 25Hz SMPTE656M 2 10Mb s Free resolution downscale at same frame rate 4 3 16 9 Selectable Other Video Resolution Aspect Ratio Audio Input amp compression Input HDMI or SDI Embedded audio Audio Compression MPEG1 Layer Il MPEG2 AAC LC MPEG4 AAC LC option for EX 5108 Sampling Rate 48KHz Compression Bit Rate 32 192Kbps Mono 64 384Kbps Stereo 128 512Kbps AAC LC DVB ASI Input Interface BNC Female 750 Maximum Input Bit rate 100 Mb s Data Transfer type Byte 188 or 204 Bytes 200 880mVp p Packet Length Signal Level DVB ASI Output Interface BNC Female 750 Max Effective Data Rate 120 Mb s Data Transfer type Byte 188 or 204 Bytes Signal Level 800 80m
19. id range from 100 216000 Kb s 38015Kb s si TS ID key in the TSID of the newly generated MPTS roms TS ID TS ID 00008 valid range from O to 65535 decimal Baroy ON remove the CA descriptors that are carried within oe Remove CA the inputted TS over ASI or IP OFF OFF keep the CA descriptors 14 www antiktech com MANTIK technology ON insert EIT into the output stream EIT data may Insert EIT come from ASl or IP input port OFF OFF don t insert EIT into the output stream Output Program Display the program list of the remux Uni Multi IP Address set the uni multicast IP address for the IP output 1 8 Uni Multi IP Address 238 069 070 001 Uni Multi UDP Port 01234 Target MAC Address 00 00 24 56 12 67 Gigabit Out Switch ON Channel 1 8 Uni Multi UDP Port set the port number valid range the streaming from 1 65535 comes from Encoder ne Target MAC Address set the destination port number MAC Address correspondingly oo Gigabit Out Switch ON OFF to switch on off the current channel Uni Multi IP Address set the uni multicast IP address for the IP output channel 9 Uni Multi IP Address 238 069 070 001 Uni Multi UDP Port 01234 Target MAC Address 00 00 24 56 12 67 Gigabit Out Switch ON Channel 9 Uni Multi UDP Port set the port number valid range the streaming from 1 65535 comes from the Target MAC Address built in Remux or set the destination port number MAC Address ASI input
20. ing is needed to pass through the gateways 8 4 MUX The device supports remux the 8 SPTS generated locally with the service s carried by the transport stream inputted via ASI In or TS IP In available only under full duplex mode The Output Bit Rate is the bit rate of the remux output the value has to be equal or greater than the total bit rate of the selected services 25 www antiktech com MANTIK technology aaa oaaae uaaa eee Status TS IP MUX System Encoder Remux Remux Packet Size 188 Byte Max Bit Rate Kbps 38015 TSID g Valid Bit Rate Kbps 0 Insert EIT off v Remove CA Off v Input TS Total 8 Output Total 0 Encoderi Encoderi Encoder Encoder Encoder Encoder3 Encoder Encoder4 Encoders Encoder5 Encoder Encoders Encoder7 Encoder Encode Encoders ASI ASI IP IP Cancel Packet Size set the packet length of the new 188 or 204 Byte Max Bit Rate Kbps Set the bitrate for the new generated MPTS valid range from 100 216000 Kb s The bitrate should be at least bigger than the total bitrate of selected programs otherwise packets may dropout TS ID Set the TSID of the new generated transport stream valid range from 0 to 65535 decimal Insert EIT ON insert EIT into the output stream EIT data may come from ASI or IP input port OFF EIT will not be inserted into the output stream Remove CA ON remove the CA descriptors that are carried within the inputted TS over ASI or IP OFF keep the CA
21. n fixed rate is selected user has to TS Clock Recovery Auto configure a bit rate to regenerate the TS clock The configured fixed bit rate has to be a little bit higher than the bit rate of the inputted TS IP IP Address set the IP address of the device valid IP Address 10 10 70 48 range from 0 0 0 0 255 255 255 255 Subnet Mask set the net mask of the device valid Net Mask 255 255 255 0 range from 0 0 0 0 255 255 255 255 Gateway set the gateway of the device valid range Gateway 10 10 70 1 from 0 0 0 0 255 255 255 255 MAC Address to display the MAC address ee Trap IP Address set the IP address of the SNMP Remote Setting Trap server valid range from 0 0 0 0 255 255 255 255 Device Label user allows to rename the device press Enter and key in the name of the device then Device Label press Enter to confirm the setting or press Exit to cancel System Software Version Software Version display the software version E Factory Default 7 3 System Network Setting Trap IP Address 10 10 70 25 Note the IP address of Enter Yes press Enter to recall the factory default Factory Default the device is not reset to settings i l the factory setting Exit No press Exit to cancel MAC Address to Modify the MAC address S N display the serial number of the device Machine Type Gigabit MAC Address to Modify the Gigabit MAC address Detail Version Display the detail version of MCU
22. n menu Main Menu NE Input Format TS IP Encoder Remux TS IP Format Refresh Status Mode Rate Full Multiple Duplex Output Full Duplex Multiple Output 1 Status show the status of the device 2 Configuration Configure and monitor parameters of encoding transcoding 3 System Configure the local settings of the device 7 2 Description of menu The main menu items can be selected with the keypad By pressing the Enter the user navigates to the sub menus which are selected in the same manner www antiktech com MANTIK technology 7 2 1 Status Sub menu Description Factory Default Value Parameter Emer 28 Fue omperemomemmo Enver ste ommemmrsmmo EST CT EmooerSBtRae oover Input Bit Rate Emmerson Erorr oever Eroson oeoo riranna CT ooo TSIP Input Bit Rate Display the TSoverP input bitrate Video 1 put Format Display tne vaso fomatofinputpont Video 2 Input Format Display tne vdeo fomatofinputpor Video 3 Input Format Display tne video format ofinputper3 Video 4 mput Format Display the vieo format ofinputpon Input Format Video 5 mput Format Display the vdeo format ofinputponS J Video 6 mput Format Display the vdeo omarorimpuporo Format Yes No Select to refresh the input video format Refresh Full Duplex Display IP in mode of column FEC and row FEC IP In Status Display IP in packets per UDP frame Display IP in received TS frames Display IP
23. nted in EIA standard 19 rack any other mounting method may lead to damage to the device e Open the box and take out the device with care Inspect if there is any damage to the appearance of the device Fix the device into the standard EIA 19 rack Connect the input and output cables It is highly recommended to put the 75Ohm loader onto the ASI output port that is not used 29 www antiktech com 30 MANTIK technology Plug the power cable into the AC Power input socket The POWER Indicator LED A4 should be green and always light on during working The EX 5108 needs 1 5 2 minutes to boot up completely Configure the network settings of the device via front panel Make the settings of Encoder Remux and IP output step by step following the instruction written in the user manual www antiktech com ANTIK Technology www antiktech com juicesales antiktech com support antiktech com MANTIK technology
24. o Scale Disable www antiktech com MANTIK technology Enable rescale the video resolution of the output manually Scale Vertical set the resolution in vertical Scale Horizontal set the resolution in horizon Null Filter Null Filter On On filter away the null packages Off the service is stuffed with null packages Note Null packet is essential for DVB applications don t remove them Encode Start Enter Yes the settings will be applied to the selected encoder and start it to encode Encode Start out Exit No cancel the settings to the selected encoder which will keep the previous status Program List select the programs to remux Click on Enter to select double click to cancel The program s will be marked with an asterisk once be selected Encoder 1 select the SPTS from encoder 1 Encoder 2 select the SPTS from encoder 2 Encoder 3 select the SPTS from encoder 3 Encoder 4 select the SPTS from encoder 4 Program List Encoder 5 select the SPTS from encoder 5 Encoder 6 select the SPTS from encoder 6 Pen Encoder 7 select the SPTS from encoder 7 Encoder 8 select the SPTS from encoder 8 ASI Input select the program s inputted via ASI input port IP Input select the program s inputted via IP input port Note this sub menu is displayed only when the IP I O is configured as full duplex mode Beale Output Bit Rate key in the bit rate of the newly Output Bit Rate generated MPTS val
25. rd can be changed by user via front panel or via submenu under the system page If the username and password are forgotten user have to set a new one via front panel 8 1 Status Via the status page user can have an overview of the current status of the connected EX 5108 DDD Status Input Status Input Format Encoderi Encoder2 Encoder3 Encoder4 Encoder5 Encoder6 Encoder Encoders 18 System Total Bit Rate Kbps Total Bit Rate Kbps Total Bit Rate Kbps Total Bit Rate Kbps Total Bit Rate Kbps Total Bit Rate Kbps Total Bit Rate Kbps Total Bit Rate Kbps Total Bit Rate Kbps Total Bit Rate Kbps y Dm mux Encoder Input Status 005002 Valid Bit Rate Kbps 003272 005002 Valid Bit Rate Kbps 003290 005002 Valid Bit Rate Kbps 003284 005002 Valid Bit Rate Kbps 003296 005002 Valid Bit Rate Kbps 003290 005002 Valid Bit Rate Kbps 003284 004998 Valid Bit Rate Kbps 003305 005002 Valid Bit Rate Kbps 003230 000000 Valid Bit Rate Kbps 000000 000000 Valid Bit Rate Kbps 000000 www antiktech com MANTIK technology Input Status sn SD O Input Status Video Format Input Format EGI Unknown Format EC2 Unknown Format EC3 Unknown Format EC4 Unknown Format EC5 Unknown Format EC6 Unknown Format EC Unknown Format ECs Unknown Format __ Input Video Format 8 2 Encoder Th
26. rform the intended measurements or shows visible damage WARNINGS e The mounting environment should be relatively dust free free of excessive vibration and the ambient temperature between 0C to 40C Relative humidity of 20 to 80 non condensed is recommended e Avoid direct contact with water e Never place the equipment in direct sunlight e The outside of the equipment may be cleaned using a lightly dampened cloth Do not use any cleaning liquids containing alcohol methylated spirit or ammonia etc e For continued protection against fire hazard replace line fused only with same type e Air intake for cooling is achieved via holes at the side of the device and the fans inside The air flow should not be obstructed Therefore the device has to be placed on a flat surface leaving some space at the sides of the device e When in operation the internal temperature should not exceed the limit of 70C www antiktech com MANTIK technology EX 5108 Series 8 Way H 264 HD SD Encoder 1 Overview EX 5108 is a series of high density real time H 264 HD SD Encoders that can support up to eight High Definition HD A V signals compressing and encoding simultaneously These A V signals can be fed into the device via 8x HDMI or 8x SDI input ports as different factory options The encoded streams can be then remultiplexed and output over its GbE IP and ASI ports All models support Time Base Correction TBC to ensure the audio and video
27. st the copyright laws in your region Also use of this product with cable television transmissions may require authorization from the cable television operator or transmitter owner VENTILATION e Do not expose the product to high temperatures such as placing it on top of other product that produce heat or in places exposed to direct sunlight or spot lighis e The ventilation slots on top of the product must be left uncovered to allow proper airflow into the device e Do not stand the product on soft furnishings or carpets e Do not stack electronic equipment on top of the product e Do not place the product in a location subject to extreme changes in temperature The temperature gradient should be less than 10 degrees C hour e Place the product in a location with adequate ventilation to prevent the build up of heat inside the product The minimum ventilation soace around the device should be 7 cm The ventilation should not be impeded by covering the ventilation openings with items such as newspapers table cloth curtains etc POWER SOURCES e The product is not disconnected from the AC power source mains as long as it is connected to the power outlet or wall socket even if the product is turned off e If the product will not be used for a long period of time disconnect it from the AC power outlet or wall socket www antiktech com MANTIK technology Before Using the Device Thank you for purchasing the EX 5108 8 Way H
28. synchronization the features necessary for the professional TV signal flow The series provide two TS IP operation modes The first is Full Duplex which allows one MPTS or SPTS inputted over 1 multicast unicast to make up a new MPTS with local encoders then sends out the new one over 1 multicast unicast In the second mode Multiple output which delivers up to 9 streams over IP There are 8 un stuffed SPTS lower bit rate but less PCR accurate than normal SPTS from local encoders and 1 MPTS from internal reMultiplexer over the IP with different Unicast or Multicast IP addresses EX 5108 allows user to configure monitoring and manage over the informative front panel and keypad or Web interface or SNMP based management software from 3rd party This Encoder family presents brilliant picture quality high density design high stability system architecture and the hot swappable power supply 2 Features gt Compile with H 264 AVC HP L4 0 gt MPEG Layer Il MPEG2 AAC LC MPEG4 AAC LC audio compression see ordering information gt 8 way real time encoder with re multiplexed integrated gt Built in re Mux accepts up to 10 SPTS MPTS 8 from local encoders 2 from external input over IP and ASI 1 ASI input for daisy chain amp Redundant ASI output Full duplex Gigabit TS over IP I O under Full duplex operation mode Up to 9 multicast unicast output under Multiple channle operation mode VBR and CBR encoding mode Free r
29. to rain or moisture e To avoid explosion danger do not dispose of batteries in an open fire CE MARK FOR EUROPEAN HARMONISED STANDARDS The CE mark which is attached to these products means it conforms to EMC Directive 89 336 EEC and Low Voltage Directive 73 23 EEC IMPORTANT INFORMATION Please retain the original packaging should it be necessary at some stage to return the device Disposal of Old Electrical and Electronic Equipment Applicable in the European Union and other European countries with separate collection systems This symbol on the product or on its packaging indicates that this product shall not be treated as household waste Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product The recycling of materials will help to conserve natural resources For more detailed information about recycling of this product please contact your local Civic Office your household waste disposal service or the shop where you purchased the product www antiktech com MANTIK technology COPYRIGHTS Television programs movies video tapes discs and other materials may be copyrighted Unauthorized recording of copyrighted material may be again
30. uggested to set Auto when there is accurate PCR carried by the inputted TS IP Fixed Rate when fixed rate is selected user has to configure a bit rate to regenerate the TS clock The configured fixed bit rate has to be a higher than the bit rate of the inputted TS IP Gigabit Output Under full duplex operation mode the device supports single uni multicast output The default source for TS IP output is the built in remux Note the page below is displayed only when the TS IP operation mode is Full duplex mode To change the TS IP operation mode please refer to chapter 8 5 System Device 25 www antiktech com MANTIK technology Status TS IP MUX i System f Encoder Gigabit Out Gigabit In Gigabit Out ee Gigabit Out IP Output Switch Enable v Source Remux ha Protocol UDP v TS Pkts Per UDP 7 v Time To Live 255 Type of Service Min Delay v Uni Multicast IP 238 1 jji Ju Uni Multicast Port 1234 ProMPEG FEC Switch Enable e IP Out Switch Enable or Disable the IP output Source select the source for the IP output in the dropdown list Protocol select UDP or RTP protocol for the IP output TS Pkts Per UDP select the number of TS packets that can be carried by each UDP packet Time To Live set TTL to the output IP packets Type of Service select the service type for the outputted IP streaming Uni Multi IP Address set the unicast or multicast IP address for the output IP streaming Uni Multi UDP Port set the port number valid
Download Pdf Manuals
Related Search