dk switch user manual
Contents
1. 10 Hours for the current setting delay TIPS 1 The setting for turn ON the mode after 23 Hours can be made by follow the step 1 to 2 then step 3 press the button 3 and press ON ALL twice Thats means we put 3 hours delay and add 10 hours 2 times and all become 23Hours P S the setting must be done within the SLEEP TIMER according to mode that been chosen 2 Mode can be CANCEL by pressing the wall switch until the LED blinking then press OFF ALL2. be ON step 3 must be completed before 15 min turned OFF To choose 4 hours ON 20 hours OFF 1 Press on any gang you want to set for timing When LED is OFF and hold on pressing until the switch starts blinking Do not release the key until step 3 completed f 2 Press on Sleep button in Remote Control Unit 30 min LED will be ON step 3 must be completed before 30 min turned OFF To choose 1 hour ON 23 hours OFF 1 Press on any gang you want to set for timing When LED is OFF and hold on pressing until the switch starts blinking Do not release the key until step 3 completed 2 Press on Sleep button in Remote Control Unit 45 min LED will be ON step 3 must be completed before 45 min turned OFF To choose scene changing mode 1 Press on any gang you want to set for timing When LED is OFF and hold on pressing until the switch starts blinking Do not release the key until step 3 completed 2 Press on Sleep button in Remote Control Unit 60 min LED will be ON step 3 must be completed before 60 min turned OFF 3 Press 1 The mode will start after 1 hour delay ex If press 2 the mode will start after 2 hours delay and so on until 9 B then press 0 it will start after 30 min s delay ex If press 1 the mode will start after 1 5 Hours delay and so on until 9 4 Press ON ALL if want to adding another
3. DK SWITCH USER MANUAL Safety Do not use the switch Do not install the switch with wet hands You could when the main power supply cause an electric leak or is ON An electric shock injure yourself might occur Installation WARNING Make sure the main power supply is turned OFF when installing the switch Basic wiring knowledge is required to ensure no injury and or damage will be inflicted onto the user and or switch Tools needed Screwdriver First turn ON the switch for the particular section the section where you want to install the lt DKSwitch gt Next turn OFF the fuse on the main fuse box one by one to identify the sections fuse Alternatively you may choose to turn OFF the main power supply Remove the old wall switch by unscrewing the screws normally covered by a plug Identify the wires Common Live L Load 1 T1 Load 2 T2 etc The Loads can either be ceiling fan or lighting load Once you have identified them unscrew the wires from the old wall switch Insert the Common Live wire to the gang with the label L on the lt DKSwitch gt Secure the gang screw Insert the Load 1 into the T1 slot Secure the gang screw Insert any additional load wires to the other gangs Secure the gang screws Place the lt DKSwitch gt back to the original switch position and secure the screws Turn the main power supply back ON Troubleshooting lt DKSwitch gt is designed to operate the best at its specified load However minor p
4. cel To Cancel the settings REMO CONTROL How to switch ON OFF To switch ON OFF a load press the switch according to the gang it is connected to Or Press the button on the remote control Remote COMOL Before you can use your remote control to control your lightings you have to set the buttons according to the lights you wish to turn ON 1 Press and HOLD 2 Wait until the switch starts blinking 3 To group 2 or more loads to the desired switch press number 1 button on the one button press the 2nd switch remote control or any other Repeat step two preferred button while still holding the wall switch button When the blinking stops the button is set How to Use the Sleep Timer 1 To activate the Sleep Timer you 2 Next press the button on the remote 3 To cancel the timer simply need to press the TIMER SELECT control unit you want to set the timer to press the button that you set to use button to select the timer 15 30 The wall switch button will blink indicating the sleep timer 45 60 minutes time interval that it has the timer set How to Use Switch Timer for DK20 To choose 12 hours ON 12 hours OFF 1 Press on any gang you want to set for timing When LED is OFF and hold on pressing until the switch starts blinking Do not release the key until step 3 completed E f 2 Press on Sleep button in Remote Control Unit 15 min LED will
5. loads to any button on the remote control Turn ON one or more loads by pressing a single button Sleep Timer lt DKSwitch gt has a Sleep Timer designed to switch OFF the lights after a period of time 15 30 45 60 minutes interval Suitable for switching off lights at night Open Circuit lt DKSwitch gt is designed with open circuit detection If one or more gang at the lt DKSwitch gt is an open circuit the gang would not function when turn ON However if other gangs that are functioning are turned ON the open circuit gang can be turned ON Open circuit gangs would not cause hazard or wastage Power Failure lt DKSwitch gt is design to keep current on off states throughout period of power failure Under cases where power supply recover from failure the switched would be brought back to their state before power failure happen gangs that were ON would be brought back ON automatically within 3 to 12 seconds Remote Control features Red LED Shows that Remote Control is functioning Green LED Shows that Sleep Timer is activated ON All To switch ON all of the lt DKSwitch gt at the same time OFF All To switch OFF all of the lt DKSwitch gt at the same time Channel A Setting the lt DKSwitch gt from 1 to 10 I dont get it Channel B Setting the lt DKSwitch gt from 11 to 20 0 to 9 Button ON OFF lt DKSwitch gt Sleep Timer To switch OFF the lights after a period of time 15 30 45 60 minutes interval Can
6. roblems might arise even if it is used properly With such cases users are advised to read through the following steps Keep in mind that only trained electricians are able to troubleshoot the circuitry of the switches and therefore it is not advised to dismantle the switches circuit If the light does not turn ON Check if the main power supply is turned ON the fuse is broken if not gt change the fuse 2A gt turn ON the main power supply the remote control s batteries power depleted gt if it still does not work please read through gt change the batteries the bulb or fluorescent light is burnt out the fluorescent starter is defective gt replace the bulb or the florescent light gt replace the starter there is loose wiring there is a faulty switch gt lt Check the Installation section of this manual gt gt please call the distributor If the fluorescent light flickers gt replace the fluorescent starter How to change the fuse 1 Turn OFF the main power supply 1 Open the fuse cover by using screwdriver no need to open all 2 Open the front of cover switch by press of fuse cover the place that shown by the arrow 2 Then replace the broken fuse with new 2 Amp fuse Features Wall Switch AND Remote Control Buttons You can choose to manually turn ON the switch or use the Remote Control up to 15 meters Set Your Own Buttons You can turn ON OFF any set of lights by assigning a single load or a group of
Download Pdf Manuals
Related Search