225P0105002001 LPC2 P01 UsrMan
Contents
1. e Dimensions in millimeters A A All connections module attachments and assembling must be done while module is not connected to the main power supply The LPC 2 P01 module should be positioned on the wall inside the room It is advised to avoid direct sunlight or position near heating cooling source object Round flush mounting box e g Gewiss GW 24232 060 mm is recommended for installation A box must be installed with screw holes in the horizontal position Mounting instructions 1 Mount LPC 2 P01 module back plate to the provided leveled place on the wall 2 Fasten 2 screws DIN 7981 or similar 03 mm max head height 3 mm to fix LPC 2 PO01 module to its place 3 Connect interconnection cable to the interconnection connector K1 Max allowed tractive force is 30 N oa Set the correct RS485 address S1 switch for LPC 2 P01 refer to the Table 4 Power PWR green LED should switch on according to the Table 5 Mount LPC 2 P01 module front plate to the back plate Fasten the screw in the bottom carefully not too strong to fix the front plate to the back plate NOTE LPC 2 MC3 main control module should be powered separately from other electrical appliance connected to LPC 2 system Signal wires must be installed separately from di mm LONgO programmable controller LPC 2 P01 special module SMARTEH LIVING SYSTEMS power and high voltage wires in accordance with general industry electrica2. Cool and heat commands are also switched off when temperature measured by the panel is inside dead band default 0 5 C temperature values Control panel PI regulator output variable range is 0 to 10000 Values from 4999 down to 0 represents cooling and vales from 5000 up to 10000 represents heating Example If proportional P parameter default 25 is set to 1 and difference between measured temperature and temperature set point is 1 C the control panel regulator output value will be 5100 On the other hand if the difference is 1 C the control panel regulator output value will be 4900 If integral parameter default 5 is set to 1 and difference between measured temperature and temperature set point is 1 C the control panel regulator output will increase every second by 100 On the other hand if the difference is 1 C the control panel regulator output will decrease every second by 100 mm Longo programmable controller LPC 2 P01 special module SMARTIFEH LIVING SYSTEMS LPC 2 P01 is connected to the main control unit RS485 port using interconnection cable e g SIC4 7 which must be ordered together with LPC 2 P01 special module When more modules e g LPC 2 ID1 LPC 2 ID2 LPC 2 P01 or up to four LPC 2 P01 are connected to main control unit splitter e g SPL 2 is also required refer to the Figure 2 LPC 2 P01 module RS485 address 0 3 is selected through two switches on the back side of the mod
3. adm 4 EN Connection Scheme rende 4 3 2 Mounting BI Lat en E 6 3 3 Module ABS occa te tend eviews sde 8 4 REGULATION DIAGRAM ku tid ea nee ation 9 5 TECHNICAL REESEN 10 6 PROGRAMMERS GUIDE Lundanes EEEE EEEE EErEE Eene 11 CHANGES Sd EE D E a 14 NOTES EE 15 3 mm LONgO programmable controller LPC 2 P01 special module SMARTFEH LIVING SYSTEMS 1 DESCRIPTION LPC 2 P01 control panel special module is used for room temperature regulation Controller is equipped with temperature sensor light intensity sensor and three push buttons WARMER a COOLER v and FAN To increase temperature set point WARMER push button is used and to decrease COOLER push button is used With FAN push button constant I II Ill or AUTO fan command can be set and the controller can also be switched off Temperature set point and fan command or controller switched off is represented with two LED bar graphs refer to the Table 3 Light intensity sensor is primary used for LED bar graph intensity control so LEDs do not disturb customer during the night if desired LPC 2 P01 has many integrated settings and functions which allows adaptation to required system and regulation diagram Settings can be done and functions can be enabled or disabled using LPC Manager software Maximum and minimum temperature set point range can be set to scale temperature set point Default range is between 18 C and 24 C If economic fu
4. 5 g SMARTTEH LIVING SYSTEMS Max temperature setpoint C Fx100 0 10000 Min temperature setpoint C Fx100 0 10000 P regulation param 0 100 regulation param 0 100 PI deadband parameter C Fx100 0 10000 Min light intensity param 0 100 Remote setpoint C Fx100 0 10000 WORD8 WORD9 WORD10 Accessing PO1 module Read LPC 2 Programmers guide for details 13 ses 3 g Longo programmable controller LPC 2 P01 special module SMARTEH LIVING SYSTEMS CHANGES The following table describes all the changes to the document Date V Description 1 7 2012 008 CGP General update 11 5 2010 007 Updated warranty permanence 2 8 2007 006 updated echnical specifications updated description about connecting to main control unit 26 4 2007 005 connection scheme updated updated power supply source 25 4 2007 004 updated power supply source updated connection scheme 31 3 2006 003 The initial version issued as LPC 2 P01 module UserManual 14 Longo programmable controller LPC 2 P01 special module SMARTFEH LIVING SYSTEMS NOTES
5. a receive send line A K1 4 Standard RS485 B Data receive send line B Table 3 LEDs amp Buttons Green LED indicates power supply status Power LED on the upper side of the module On power supply OK Off power supply missing or power off Red LED indicates On RS485 communication Internal fault LED on the LPC 2 1D1 f D ault upper side of the module communication Off RS485 communication OK state Green LEDS indicates actual Temperature set point temperature Set point between min On represents actual set LED bar graph and max point Temperature set point range Green LEDs indicates man fan On represents selected man Fan LED bar graph speed auto or fan reference or auto mode controller off Off controller off command selection Push button set D NE Set point increased by one WARMER point increase 1 command step when pressed Push button set COOLER point decrease ge Ge by one command p H Table 4 S1 RS485 ADDRESS Switch 1 Switch 2 0 OFF OFF 1 OFF ON 2 ON OFF 3 ON ON 1 Each step means 1 12 of pre setted temperature set point range PA mm LONgO programmable controller LPC 2 P01 special module SMARTFEH LIVING SYSTEMS 3 2 Mounting instructions Figure 3 Housing dimensions 40 6 LL HEG ah 17 59 MO IA OT I EEE i IN j co 45 45 SS 60 10
6. ex 6 SMARTFEH LIVING SYSTEMS USER MANUAL Longo programmable controller LPC 2 P01 special module Version 8 SMARTEH doo Trg tigrovcev 1 5220 Tolmin Slovenia Tel 386 0 388 44 00 e mail info smarteh si www smarteh si mm LONgO programmable controller LPC 2 P01 special module SMARTEH LIVING SYSTEMS Written by SMARTEH doo Copyright 2012 SMARTEH doo User manual Document Version 008 July 1 2012 eg LONgO programmable controller LPC 2 P01 special module SMARTFEH LIVING SYSTEMS STANDARDS AND PROVISIONS Standards recommendations regulations and provisions of the country in which the devices will operate must be considered while planning and setting up electrical devices Work on 230 VAC network is allowed for authorized personnel only DANGER WARNINGS Devices or modules must be protected from moisture dirt and damage during transport storing and operation WARRANTY CONDITIONS For all modules LONGO LPC 2 if no modifications are performed upon and are correctly connected by authorized personnel in consideration of maximum allowed connecting power we offer warranty for 24 months from date of sale to end buyer In case of claims within warranty time which are based on material malfunctions the producer offers free replacement The method of return of malfunctioned module together with description can be arranged with our authorized representative Warranty does no
7. ge Comm status Normal Economy mode Local Remote status Hot valve status Cold valve status System status Change over function status 2 4 pipe status VBOOLS N 1 variable range Fan speed status Fan speed II status Fan speed III status BIT3 Fan speed mode BIT5 Enab Dis balcony status Enab Dis window status 3 11 mm LONgO programmable controller LPC 2 P01 special module VBOOLS N 2 g SMARTTEH LIVING SYSTEMS variable range BITO Normal Economy command Local Remote command BIT3 TF 0 1 Start Stop command Change over command 2 4 pipe command VBOOL8 N 3 variable range BITO BIT1 BIT2 BIT3 Balcony door status ve Window switch status Enab Dis balcony door cmd Enab Dis window command VWORD16 N 4 variable range Max temperature status C Fx100 0 10000 Min temperature status C Fx100 0 10000 P regulation status 0 100 regulation status 0 100 PI deadband status C Fx100 0 10000 Fan speed reference 0 10000 Temperature setpoint C Fx100 0 10000 Space temperature C Fx100 0 10000 Absolute PI reference 0 10000 Light intensity 0 100 VWORD16 N 5 variable range 3 12 o 3 Longo programmable controller LPC 2 P01 special module VWORD16 N
8. l installation standard LONgO programmable controller LPC 2 P01 special module SMARTFEH LIVING SYSTEMS 3 3 Module labeling Figure 5 Labels on housing Label 1 Label 2 LPC 2 MC3 P N 225MC304001001 S N MC3 S9 0500000190 D C 16 05 C Label 1 description 1 LPC 2 MC3 is the full product name 2 P N 225MC3040001001 is the part number e 225 general code for LPC 2 product family e MC3 short product name e 04001 sequence code e 04 year of code opening e 001 derivation code e 001 version code reserved for future HW and or SW firmware upgrades 3 D C 16 05 is the date code e 16 week and e 05 year of production Label 2 description 1 S N MC3 S9 0500000190 is the serial number e MC3 short product name e S9 user code test procedure e g Smarteh person xxx e 0500000190 year and current stack code e 05 year last two cyphers e 00000190 current stack number previous module would have the stack number 00000189 and the next one 00000191 3 00 Longo programmable controller LPC 2 P01 special module SMARTIFEH LIVING SYSTEMS 4 REGULATION DIAGRAM Regulation dead band Heating Cooling Space temp C Fan reference output Temp Setpoint 100 67 Speed Ill o 33 Speed Il Al REPAS i Ster nen Space temp C PI regulator output Temp Setpoint Space temp C 3
9. nction is set controller will start cooling when room temperature will raise above max temperature set point and stop when temperature will drop 1 C below max temperature set point On the other hand when room temperature will fall below min temperature set point controller will start heating and stop when temperature will raise 1 C above min temperature set point When four pipe default system is selected controller will activate hot command when heating and cool command when cooling is required In case of two pipe system selection hot command is always activated when heating or cooling is required depends on heating or cooling mode selection For example that two pipe system cooling mode is selected and room temperature is higher than temperature set point on the control panel controller will activate cooling with hot command cool command is off if heating or cooling is required In case that balcony door and or window function is enabled and door and or window contact is opened fan will go to the first I speed and valves for heating or cooling will be closed Frost protection function activates heat command when room temperature measured by the panel drops below 5 C This function has priority over all control panel integrated functions LPC 2 P01 control panel is possible to switch off using FAN push button or off command is set from LPC Manager software In this case cool heat and fan commands are switched off
10. ss 3 Longo programmable controller LPC 2 P01 special module SMARTTEH LIVING SYSTEMS 5 TECHNICAL SPECIFICATIONS Table 5 Technical specifications Power supply from main control unit LPC 2 MC7 Interconnection connector type Berg M Power consumption 0 5 W Temperature measurement accuracy 1 C Dimensions L x W x H 80 x 110 x 17 mm Weight 80g Maximum altitude 2000 m Mounting position vertical Ambient temperature 0 to 50 C Ambient humidity max 95 no condensation Transport and storage temperature 20 to 60 C Protection class IP 30 10 mm LONgO programmable controller LPC 2 P01 special module SMARTIFEH LIVING SYSTEMS 6 PROGRAMMERS GUIDE Brief description LPC 2 PO1 control panel module is used for room temperature regulation This module must be connected to LPC 2 C04 module The RS485 address for an PO1 module can be set from 0 to 3 The address is set through two switches on the back side of the module It has many integrated settings and functions which allows adaptation to required system and regulation diagram Settings can be done and functions can be enabled or disabled through LPC Manager software Variables There are 22 bytes available for reading and writing from to POL module While whole frame of 26 bytes is transferred at a time LPC Manager variables described in the table below are accessed separately VBOOLB8 N variable ran
11. t include damage due to transport or because of unconsidered corresponding regulations of the country where the module is installed This device must be connected properly by the provided connection scheme in this manual Misconnections may result in device damage fire or personal injury Hazardous voltage in the device can cause electric shock and may result in personal injury or death NEVER SERVICE THIS PRODUCT YOURSELF This device must not be installed in the systems critical for life e g medical devices aircrafts etc If the device is used in a manner not specified by the manufacturer the degree of protection provided by the equipment may be impaired gt Waste electrical and electronic equipment WEEE must be collected separately LONGO LPC 2 complies to the following standards e EMC EN 61000 6 2 EN 50082 EN 61000 6 4 EN 50081 e LVD IEC 61131 2 e Vibrations and climatic mechanical EN 60068 2 6 EN 60068 2 27 EN 60068 2 29 Smarteh doo operates a policy of continuous development Therefore we reserve the right to make changes and improvements to any of the products described in this manual without any prior notice MANUFACTURER SMARTEH d 0 0 Trg tigrovcev 1 5220 Tolmin Slovenia mm LONgO programmable controller LPC 2 P01 special module SMARTIFEH LIVING SYSTEMS Index Longo programmable controller LPC 2 P01 special module TRES SPION 1 EECHER aan 3 3 INSTALLA MON ne amener a
12. ule refer to the Table 4 NOTE For proper system configuration and data allocation please refer to LPC Composer software help menu 3 Longo programmable controller LPC 2 P01 special module SMARTFEH LIVING SYSTEMS 2 FEATURES Figure 1 LPC 2 P01 special module Table 1 Technical data Temperature measurement room temperature 2 push buttons for temperature set point 1 push button for manual fan speed auto and controller off 12 LED bar graph for temperature set point 4 LED bar graph for manual auto fan speed setting Light intensity measurement LED intensity control Step less or 3 step fan motor controlling Economic function Two four pipe heating cooling system supported Balcony door and window function Frost protection function Power LED Internal fault LED Interconnection cable SIC4 7 not included Longo programmable controller LPC 2 P01 special module SMARTFEH LIVING SYSTEMS 3 INSTALLATION 3 1 Connection scheme Figure 2 Connection scheme SIC4 7 SIC4 7 7 Fa SIC4 7 SIC4 7 Future use module ID1 ID2 P01 4321 K1 Backside connection mm LONgO programmable controller LPC 2 P01 special module Table 2 K1 g SMART EH LIVING SYSTEMS K1 1 GND Ground K1 2 9 VDC Power supply input K1 3 Standard RS485 A Dat
Download Pdf Manuals
Related Search