Tektronix SD14 User Manual
Contents
1. IS GIVEN BY TEKTRONIX WITH RESPECT TO THIS PRODUCT IN LIEU OF ANY OTHER WARRANTIES EXPRESSED OR IMPLIED TEKTRONIX AND ITS VENDORS DISCLAIM ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE TEKTRONIX RESPONSIBILITY TO REPAIR OR REPLACE DEFECTIVE PRODUCTS IS THE SOLE AND EXCLUSIVE REMEDY PROVIDED TO THE CUSTOMER FOR BREACH OF THIS WARRANTY TEKTRONIX AND ITS VENDORS WILL NOT BE LIABLE FOR ANY INDIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES IRRESPECTIVE OF WHETHER TEKTRONIX OR THE VENDOR HAS ADVANCE NOTICE OF THE POSSIBILITY OF SUCH DAMAGES A CA Product Description SD 14 Opt 01 Instructions The SD 14 Opt 01 is a variation on the standard SD 14 Probe Sampling Head that features the following modifications m Probe tip length extended 0 040 1 0mm m Ground barrel threaded 10 40 at top m Additional custom accessories Probe to etched circuit board ECB adapters Probe to SMB adapters The SD 14 Opt 01 is used with the 11801 family of Digital Sampling Oscillo scopes or the CSA803 family of Communications Signal Analyzers The tip design will accommodate all of the standard accessories provided for the standard SD 14 4mm Probe Tip size For more information on the SD 14 Opt 01 that is not specific to this Mod refer to the SD 14 User Manual 070 8286 01 NOTE The Probe to ECB Adapter and the Probe to SMB Adapter can only be used with the SD 14 Opt 01 probes Do not attempt to use them with th2. Instructions Tektronix Y SD 14 Opt 01 Sampling Head 063 2011 01 First Printing January 1994 Instrument Serial Numbers Each instrument manufactured by Tektronix has a serial number on a panel insert or tag or stamped on the chassis The first letter in the serial number designates the country of manufacture The last five digits of the serial number are assigned sequentially and are unique to each instrument Those manufactured in the United States have six unique digits The country of manufacture is identified as follows B010000 Tektronix Inc Beaverton Oregon USA E200000 Tektronix United Kingdom Ltd London 4300000 Sony Tektronix Japan H700000 Tektronix Holland NV Heerenveen The Netherlands Instruments manufactured for Tektronix by external vendors outside the United States are assigned a two digit alpha code to identify the country of manufacture e g JP for Japan HK for Hong Kong IL for Israel etc Tektronix Inc PO Box 500 Beaverton OR 97077 Printed in U S A Copyright O Tektronix Inc 1994 All rights reserved Tektronix products are covered by U S and foreign patents issued and pending The following are registered trademarks TEKTRONIX TEK TEKPROBE and SCOPE MOBILE WARRANTY Tektronix warrants that this product will be free from defects in materials and workmanship for a period of one 1 year from the date of shipment If any such product proves defective during this warranty period
3. Tektronix at its option either will repair the defective product without charge for parts and labor or will provide a replacement in exchange for the defective product In order to obtain service under this warranty Customer must notify Tektronix of the defect before the expiration of the warranty period and make suitable arrangements for the performance of service Customer shall be responsible for packaging and shipping the defective product to the service center designated by Tektronix with shipping charges prepaid Tektronix shall pay for the return of the product to Customer if the shipment is to a location within the country in which the Tektronix service center is located Customer shall be responsible for paying all shipping charges duties taxes and any other charges for products returned to any other locations This warranty shall not apply to any defect failure or damage caused by improper use or improper or inadequate maintenance and care Tektronix shall not be obligated to furnish service under this warranty a to repair damage resulting from attempts by personnel other than Tektronix representatives to install repair or service the product b to repair damage resulting from improper use or connection to incompatible equipment or c to service a product that has been modified or integrated with other products when the effect of such modification or integration increases the time or difficulty of servicing the product THIS WARRANTY
4. be tip thread the SMB adapter to the probe before making caonnection to the SMB connector Likewise disconnect the SMB before removing the SMB adapter from the probe To disconnect the SMB connector simply pull on the probe The adapter will stay with the probe CAUTION Pull only on the probe body Do not pull on the probe cable as damage may result to the probe The specifications listed below pertain only to the addition of Opt 01 to the SD 14 Refer to the SD 14 User Manual 070 8286 01 for any information not listed here m Probe Input Impedance 100K ohm typical 0 550pF typical m Field Replaceable Unit 657 0097 50 m Standard Accessories Probe Etched Circuit Board Adapter Replace with 020 2081 00 5 ea Probe to SMB Adapter Replace with 020 2082 00 5 ea CAUTION The SD 14 User and Service Manuals call out the use of a Calibration Fixture 013 0271 00 The SD 14 Opt 01 must be tested only with an updated version of this fixture Part number 013 0271 01 The updated version of this fixture remains compatible with the standard SD 14 SD 14 Opt 01 Instructions
5. e standard SD 14 probes Etched Circuit Board Etched Circuit Board Adapter Figure 1 Probe to Etched Circuit Board Adapter The Probe to Etched Circuit Board ECB Adapter is intended to provide a solid mating of the probe tip to a ground signal ground ECB pattern Adjacent pin spacing is 0 075 0 95mm The center signal conductor of the probe protrudes through this adapter and serves as the signal carrying member of the probe and adapter assembly The adapter is installed onto the probe tip by gently twisting it counter clockwise while simultaneously pushing it onto the barrel until it stops It may be removed by twisting it counter clockwise while pulling it off va TS Keep this area free of obstructions Z R 0 125 0 32 mm v Ground pra Ground 0 075 0 95 mm i3 0150 Plated hole 3 places S 1 91 mm y 0 029 0 035 0 74 89 mm preferrable EAN pra 0 029 0 039 0 74 0 99 mm acceptable Se ee 0 055 1 40 mm diameter pad maximum Figure 2 Required ECB Mating Pattern To test an ECB pattern align the ground signal ground leads to the hole pattern in the ECB and gently push the probe straight into the ECB until it stops CAUTION To avoid damage to the probe tip Do not apply excessive side force to the probe Maintain the probe at a right angle 90 degree to the ECB SD 14 Opt 01 Instructions Commercial SMB Connector not supplied SMB Adapter Fig
6. ure 3 Probe to SMB Adapter The Probe to SMB adapter is intended to provide a solid mating of the probe tip to an SMB jack coaxial connector It is a coaxial adapter that is equipped with a probe socket on one side and a SMB plug on the other side One type of application is illustrated above where a right angle SMB jack to ECB connector 1s used to mate the probe and the to the ECB The required ECB pattern depends on the type of SMB jack to ECB adapter used as there are several available commercially The following list should serve as a guideline to selecting the proper connector for your application Application Manufacturer Manufacturer s Part Number Right angle ECB Mount E F Johnson 131 1701 371 Straight ECB Mount E F J ohnson 131 3701 201 ECB End Launch 0 062 board E F Johnson 131 3701 801 Use care when placing right angle connectors with regard to both the direction the probe extends outward and also the vertical clearance of the probe to the board Many SMB right angle connectors are very low profile and do not allow the probe to extend over a usable area of the ECB The threaded adapter is installed onto the probe tip by gently twisting it clockwise onto the barrel until it stops It may be remove by twisting it counter clockwise The SMB connection is then made by pushing the connectors together until a snap is felt SD 14 Opt 01 Instructions 3 Specifications A CAUTION To avoid damage to the pro
Download Pdf Manuals
Related Search