USER MANUAL
Contents
1. RGBTO WHITEis set to YES on RGB 255 255 255 the color is perfect white as the actual RGB values are adjusted to make white When it is setto NO 255 255 255 the RGB values are not adjusted and the output is most powerful The RGB s parameter can be adjusted in 121 e Enter POW to choosethe operation power mode NORM or HIGH when itis normal mode the power consumption is about 90W while under high mode itis about 150W e Enter Dim to select dimmermode and dimmerspeed When DIMMERis set to then RGBW and MASTER DIMMER are linear The Dim 1 2 3 4 are speed modes ofthe nonlinear dimmer Dim1 is the faster while Dim4 is the slowest e The Dim setting here does notreact onthe the STAG mode 3 DISPLAY PANEL OPERATION 12 2008 8 13 3 11 WHITES SETTING MENU gt gt j Red je 0 255 WTO02 Green 0 255 Blue 0 255 White 0 255 WT11 CAL11 e Enter the CAL1 to select white color of different color temperature e There are 11 pre programmed White colors can be edited by using Red Greenl Bluel amp White 3 12 WHITE BALANCE MENU cat _ gt RGBW z Red e 0 255 Green 0 255 Blue 0 255 21 e Enter the CAL2 to adjust the RGB parameter to make different whites e When the new settingis activated the DMX controller choose RGB 255 255 255 the white colo2. USER MANUAL VER 1 0 Brile LIGHT RESEARCH ABLE OF CONTENTS PART1 1 1 1 1 PRODUCT 1 1 2 PRODUCT 1 1 3 TECHNICAL 5 2 1 4 2 3 1 5 SAFETY 2 1 1 0 0 0606660000000000 000000000000 4 PART2 INSTALLATION eese 5 2 MOUNTING vi DR ik 5 2 2 nnne nnne nna 5 2 3 SETTING UP WITH A DMX512 6 2 3 1 DMX512 ADDRESSING WITHOUT ID 6 2 3 2 DMX512 ADDRESSING WITHID APDRESS 6 PART3 DISPLAY PANEL 8 3 1 BA SIC 8 Ore MENU 52524552 SATA 21224323 9 3 3 EDIT STATIC COLOUR 10 3 4 ACTIVATING 5 6 10 9 5 R N MODE e eed 10 3 6 5 12 86 72 0
3. Display IC damaged 1 Buttons damaged 2 Display IC damaged 1 Signal Cableerror 2 Signal conncetionerror 3 The DMXsignal receive IC damaged 4 DMX addresserror 1 The heatsensor resistance of LED board error 2 The temperature protection circuit onthe display error ACTION 1 Check powersupply 2 Check powerconnection 3 Replace display 4 Check thelC and allthe connections 5 Adjustthe LCD contrast 1 Check Display IC installation andquality 1 Replace buttons 2 Replace Display IC 1 Check allsignal Cables 2 Check allsignal conncetions 3 Check the DMX signal receive IC 4 Check DMX address 1 Replace the heat sensor resistance 2 Check thetemperature protection circuit Color mixing uneven with splash 1 LED notjoining well 2 Lens notinstalling well 1 Check LEDsjoining 2 Check lensinstalling Partial color partial red partial green or partial blue 1 The currentof one ofthe color groupLEDs is too strongor too weak 2 LED brightness not enough 1 Check 2 Check LEDquality LEDs of thesame color are notlit 1 LED damaged 2 LED damagedor Main PCB 1 Replace LEDs 2 Replace damagedLED or Main PCB Manual and program can not save 1 Saving IC damaged 20 1 Replace savinglC 2008 8 13 5 2 1 2 Rubber seal 3 Clear glass 4 Lens comple
4. CUSTOM 8 201 lt gt 210 CUSTOM 9 211 lt gt 220 CUSTOM 10 221 lt gt 255 NO FUNCTION AUTO SPEED ADJUSTMENT 2 0 lt gt 255 when using CH8 AUTOO1 AUTO10 this function activated DIMMER SPEED lt gt 9 PRESET DIMMER SPEEDFROM DISPLAYMENU 10 lt gt 29 LINEAR DIMMER 10 30 lt gt 69 NONLINEAR DIMMER fastest 70 lt gt 129 LINEAR DIMMER2 130 lt gt 189 NON LINEAR DIMMER3 190 lt gt 255 NON LINEAR DIMMER4 slowest ID ADDRESS lt gt 9 01 1066 10 lt gt 19 01 20 lt gt 29 2 n 30 lt gt 39 D3 40 lt gt 49 4 50 lt gt 59 05 4 USINGA DMX512CONTROLLER 15 2008 8 13 CHANNEL VALUE FUNCTION 60 lt gt 69 06 70 lt gt 79 07 80 lt gt 89 08 90 lt gt 99 09 100 lt gt 109 010 110 lt gt 119 011 120 lt gt 129 012 130 lt gt 139 013 140 lt gt 149 014 11 150 lt gt 159 015 160 lt gt 169 016 170 lt gt 179 D17 180 lt gt 189 018 190 lt gt 199 019 200 lt gt 209 020 210 021 211 022 254 1065 255 066 1 CHANNEL VALUE FUNCTION 1 0 lt gt 255 RED 2 0 lt gt 255 GREEN 3 0 lt gt 255 BLUE 4 USINGA DMX512CONTROLLER 16 2008 8 13 Arl d CHANNEL 1 VALUE FUNCTION 0 lt gt 255 MASTER DIMMER 0 lt gt 255 RED Arc 2 CHANNEL 1 0 lt gt 255 GREEN 0 lt gt 255 BLUE VALUE FUNCTION 0 lt gt 255 0 lt gt 255 GREEN 0 lt gt 255 BLUE
5. e 1 2 3 e 1 should beset inthe Settings menu on eachunit e ID addresses are accessible from Ch9 on the DMX512 controller 2 INSTALLATION 6 2008 8 13 DMX Adar 1 DMX Adar 1 DMX Adar 1 DMX Adar 12 DMX Addr 12 DMX Adar 12 ID Adar 1 ID 2 ID 3 ID 1 ID 2 ID Adar 3 c E E gt The figure above shows simple DMX layout which has usedthree units ateach DMX address The three units have different ID addresses which allows the user to collectively control the whole group ofunits atthat DMX address by setting CH11 to 0 or tocontrol each unit independently by first selecting the DMX address and then by using CH11 to locate the target ID address 2 INSTALLATION 7 2008 8 13 3 DISPLAY PANEL OPERATION 3 1 BASIC The LED fixtureis mounted witha LCD display and 4 control buttons OOOO MENU ENTER UP DOWN MENU 1 scroll through the main menu or return to the main menu ENTER enter thecurrently selected menu orconfirm the current function value UP 1 scroll UP through the menulist or increase the value of the current function DOWN 1 scroll DOWN through the menu list or decrease the value of the current function 3 DISPLAY PANEL OPERATION 8 2008 8 13 3 2 MENU 11111 gt KEY J 2008 8 13 9 3 DISPLAY PANEL OPERATION 3 3 EDIT STATIC COLO
6. m 1 PRODUCT GENERAL 3 2008 8 13 1 5 SAFETY WARNING IMPORTANT ALWAYS READ THE USER MANUAL BEFORE OPERATION 1 PLEASE CONFIRM THAT THE POWER SUPPLY STATED ON THE PRODUCT IS THE SAME AS THEMAINS POWER SUPPLYIN YOUR AREA e This product must be installed by a qualified professional e Always operate the equipmentas describedin the user manual minimum distance of 0 5m must be maintained between the equipment and combustible surface e The product must always be placedin a well ventilated area e Always make sure thatthe equipmentis installed securely e DO NOT stand close to the equipment and stare directly into the LED light source e Always disconnectthe power supply before attempting and maintenance e Always make sure that the supporting structure is solid and can support the combined weight ofthe products e The earth wire must always be connected tothe ground e Do not touchthe power cablesif your handsare wet ATTENTION e This product 1 place of manufacture perfectcondition In orderto maintain this condition and for safe operation the user must always follow the instructions and safety warnings described in this user manual e Avoid shaking or strong impactsto any partof the equipment e Make sure thatall parts ofthe equipment are kept clean and free of dust e Always make sure that the power connections are connected correct and secure elf thereis any malfun
7. 0 00000000000000 nnns 11 PERSONALITY 24 11 3 8 5 11 3 9 EDITING CUSTOM PROGRAMS 12 3 10 SPECIAL SETTINGS 12 3 11 WHITES SET TINQ err ee 13 3 12 WHITES BALANG Es 13 3 13 PASSWORD 2 13 PART4 USINGA 512 14 4 1 BASIC 9 2 2 14 4 2 CHANNEL 55 9 14 4 3 BASIC INSTRUCTIONS FOR 512 19 PART 5 APPENDIX 20 5 1 TROUBLE 20 52 MAINTENANGE 21 1 PRODUCT GENERAL 1 7 PRODUCT INTRODUCTION This product is designed for indoor or outdoor use Suitable applications include wash or effect lighting for architectural stage theatre or road show applications Direct input of DMX512 signal allows the units to be controlled from any DMX512 controller This product can be operatedas a singleunit or inmultiple units forlarge applications 1 2 PRODUCT FEATURES LED FIXTURE P67 protection rating RGBW Dimmer 0 100 Strobe Built in automatic programs Upload custom parameters to slave fixtures LEDdisplay Disp
8. Ar2 d CHANNEL 1 0 lt gt 255 VALUE FUNCTION 0 lt gt 255 MASTER DIMMER 0 lt gt 255 0 lt gt 255 0 lt gt 255 BLUE 4 USINGA DMX512 CONTROLLER 0 255 WHITE 17 2008 8 13 2 5 CHANNEL VALUE FUNCTION 1 0 lt gt 255 MASTER DIMMER 2 0 lt gt 255 RED 3 0 lt gt 255 GREEN 4 0 lt gt 255 BLUE 5 0 lt gt 255 WHITE 6 0 lt gt 255 STROBE HSV CHANNEL VALUE FUNCTION 1 0 lt gt 255 HUE 0 100 2 0 lt gt 255 SATURATION 0 100 3 0 lt gt 255 VALUE 0 100 4 USINGA DMX512 CONTROLLER 18 2008 8 13 4 3 BASIC INSTRUCTIONS FOR DMX512 OPERATION STAGE 1 MASTER DIMMER e controls the intensity of the currently projected color e When the slider is at the highest position 255 theintensity ofthe outputis the maximum RED GREEN amp BLUE amp WHITE COLOR SELECTION e CH2 CH3 amp CH4 amp CH5control the intensity ratio of each of the RED GREEN BLUE amp WHITE LEDs e When the slideris atthe highest position 255 the intensity of the color is themaximum e CH2 CH3 CH4 amp CH5 canbe combined togetherto create over16 million colors COLOR MACROS e CH6 selectsthe required COLOR MACRO e CH6 has priority over CH2 CH3 CH4 amp CH5 e CH1 is usedto control theintensity of the COLOR MACRO STROBE e CH 7 controls the strobe of CH1 to CH6 e Strobe 1 is with R
9. EL OPERATION 11 2008 8 13 3 9 EDITING CUSTOM PROGRAMS MENU gt J PRO _ 01 _ gt Red gt 0 255 02 5 02 Green 0 255 Blue 0 255 White 0 255 PR 10 SC 30 Strobe 0 20 0 255 0 255 EDIT CUSTOM e Enter the EDIT mode to editthe custom programs PR 01 to PR 101 e Each custom program has 30 steps that can be edited e Each step allowsthe creation ofa scene usingRED Red GREEN Green BLUE Blue WHITE White STROBE Strobe TIME Time amp FADE Fade 3 10 SPECIAL SETTINGS MENU gt gt e REST Je ID gt OFF RGBW _ OFF POW gt HIGH NORM Dim gt Off Dim1 Dim2 Dim3 Dim4 SETTING e Select UPLD to upload thecustom programs fromthe current MASTERunit to the SLAVE units e In orderto activate the upload function the password mustbe entered e Password isthe same as the main access password e When uploading the MASTER and SLAVE units willdisplay YELLOW e If an error occurs when uploading the MASTER and or SLAVE units will display RED e On successful uploading of the custom programs the MASTER and SLAVE units will display GREEN e In order toreset custom modesto default valuesselect REST e Enter 1 in order to allow disallow ID address function from the DMX512 controller e When RGBW
10. GB in step e Strobe 2is with RGB out step e Strobe 3 isa pulse strobe faston slow off e Strobe 4 isa pulse strobe slow on fast off e CH7 has priority over CH2 CH3 amp CH5 ID ADDRESSSELECTION e 9 is usedto select thetarget ID address e Each independent DMX address haveupto 66 independentID addresses e An Daddress of Owill activate address locations AUTO e CH8 selectsthe preset AUTO programs AT 01 AT 10 orthe custom AUTO programs CUS 01 CUS 10 e When activating the custom AUTO programs CUS 01 to CUS 10then itis possible to control the STEP TIME and FADE TIME using CH2 and CH3 respectively e CH8 has priority over CH2 CH3 CH5 CH6 CH7 DIMMER SPEED e CH10 is for selecting the dimmermode and dimmerspeed When DIMMERis set to Off then RGBW and MASTER DIMMER are linear The Dim 1 2 3 4 are different speedof the non linear dimmer 4 USINGA DMX512CONTROLLER 19 2008 8 13 5 APPENDIX 5 1 5 SITUATION No display LED MODULE on but nocontrol from display Display normal but no response from buttons No DMX signal When the surface temperature of the unit exceed 75 C the temperature protection no work TROUBLE SHOOTING CAUSE 1 No powerinput 2 Power connectionerror 3 Display damaged 4 Display error or power input connection error or two boardconnection error 5 Contrast decay 1 Display ICreverse install 2
11. GREEN UP BLUE 096 51 lt gt 70 RED DOWN GREEN 100 BLUE0 71 lt gt 90 RED 0 GREEN100 BLUE UP 91 lt gt 110 RED 0 GREENDOWN BLUE 100 111 lt gt 130 RED UP GREEN 0 BLUE 100 131 lt gt 150 RED 100 GREEN 0 BLUE DOWN 151 lt gt 170 RED 100 GREEN UP BLUE UP 171 lt gt 190 RED DOWN GREEN DOWN BLUE 100 6 191 lt gt 200 RED100 GREEN100 BLUE100 WHITE 100 201 lt gt 205 WHITE 1 3200K 206 lt gt 210 WHITE 2 3400 211 lt gt 215 WHITE 3 4200K 216 lt gt 220 WHITE 4 4900K 221 lt gt 225 WHITE 5600K 226 230 WHITE 6 5900K 4 USINGA DMX512CONTROLLER 14 2008 8 13 CHANNEL VALUE FUNCTION 231 lt gt 235 WHITE 7 6500 236 lt gt 240 WHITE 8 7200K 6 241 lt gt 245 WHITE 9 8000 246 lt gt 250 WHITE 10 8500K 251 lt gt 255 WHITE 11 10000K STROBE 7 0 10 NO FUNCTION 11 lt gt 255 1 20Hz AUTO 0 lt gt 20 NO FUNCTION 21 lt gt 30 AUTO 31 lt gt 40 AUTO2 41 lt gt 50 51 lt gt 60 AUTO4 61 lt gt 70 AUTOS 71 lt gt 80 44706 81 lt gt 90 44707 91 lt gt 100 AUTOS 101 lt gt 110 AUTO9 111 lt gt 120 AUTO 10 8 1214 5130 CUSTOM 1 131 lt gt 140 CUSTOM 2 141 lt gt 150 CUSTOM 3 151 lt gt 160 CUSTOM 4 161 lt gt 170 CUSTOM 5 171 lt gt 180 CUSTOM 6 181 lt gt 190 CUSTOM7 191 lt gt 200
12. N 5 2008 8 13 2 3 SETTING UP WITHA DMX512 CONTROLLER 2 3 1 DMX512 ADDRESSING WITHOUT ID ADDRESSING STAG MODE e Connect the DMX512controller to theunits in series e Each unithas 11 DMX channels sothe DMX Addresses should increase by increments of 11 e g 1 12 23 34 eThe ID addresshas not beenset so therefore when usingthe controller CH11 must be inactive CH11 0 elt is also possible to deactivate ID address selecting ID OFF from the Settings menu on the fixture e Each DMX Address may be used as many times as required e Any DMX address inthe range from 001 to 512 may beused Example DMX 1 DMX Adar 12 DMX Adar 23 f x 95 520 I DMX512 CONTROLLER CIDERSESXEXEEEXITIEEE The figure above shows a simple DMX512 layout with thestarting address ofthe first unit setat 1 with the second setat 12and so on Note that when usedin this the CH11 ID function must be inactive 11 0 2 3 2 DMX512 ADDRESSING WITH ID ADDRESS STAG MODE e Connect the DMX512 controller to the units series e Each unithas 11 DMX channels sothe DMX Addresses should increase by increments of 11 e g 1 12 23 34 e Each DMX Address may beused as many times as required e Any DMX address inthe range from 001 to 512 may beused e Each DMX address may carry upto 66 separatelD addresses e D should beset inthe menuon eachunit in ascending values i
13. UR MENU stat gt Red 0 255 Green gt 0 255 Blue j 0 255 White 0 255 Strob 0 20 STATIC COLOUR e Combine Red Green Blue and White to create infinite range of colors 0 255 e Set thevalue ofthe Strobe 0 20Hz 3 4 ACTIVATING AUTO PROGRAMS MENU auro je aro AT02 _ AT 10 PR 01 PR 02 10 AUTO e Select the target AUTO program and press ENTER e Programs 011 to 101 are fully pre programmed and will altered by changes EDIT mode e Programs PH 01 101 are fully pre programmed and can be edited in EDIT mode 3 5 RUN MODE MENU gt __ gt a SLAV RUN e Enter the RUN 1 mode set working mode e DMX mode is forusing the DMX512controller to controlthe fixtures e SLAV mode isfor Master Slave operation 3 DISPLAY PANEL OPERATION 10 2008 8 13 3 6 DMX512 SETTINGS MENU 0 001 512 DMX Enter the DMX mode to setthe DMXADDRESS 3 7 PERSONALITY MENU gt PERS gt STAG Arc 1 1 2 2 Ar2 s HSV PERSONALITY e Enter the PERSONALITY mode to select DMX mode STAG Arc 11 Ar1 d Arc 21 Ar2 d 2 or HSV 3 8 IDADDRESS MENU gt ID 10 01 66 ID e Enter the D mode to setthe 10 ADDRESS 3 DISPLAY PAN
14. ction ofthe equipment contact your distributor immediately e When transferring the product it is advisable to use the original packaging which the productleft the factory e Shields lenses orultraviolet screens shallbe changed ifthey have become damaged to such an extent thattheir effectivenessis impaired e The lamp LED shall be changed if ithas become damaged or thermally deformed 1 PRODUCT GENERAL 4 2008 8 13 2 INSTALLATION 2 1 MOUNTING HANGING The fixture can be mounted ina hanging position using the supporting bracket The bracket should be secured to the mounting truss or structure using a standard mounting clamp Please note that when hanging the unit a safety cable should also be used UPRIGHT The fixture can be mounted in an upright or sitting position usingthe supporting brackets The LED MODULE can be mountedat any angleand in any position It ispossible to furtheradjust the angleof the LED MODULE using thetwo adjustment knobslocated on theside of the fixture 2 2 POWER CONNECTIONS 220V 10 units may be connected in series 120V 5units may be connectedin series Note 1 As this fixture s DMX signal cable connection is Parallel connection so if over 32 units to be connected then a DMX signal amplifieris needed 2 If the signal cable is over 60m between the DMX512 controller and fixture or beween two fixtures then a DMX signal amplifieris needed as well 2 INSTALLATIO
15. lay control lock out Direct DMX512 input Independent ID address Different white colors setting Over heat protection 1 PRODUCT GENERAL 1 2008 8 13 1 3 TECHNICAL SPECIFICATIONS LED MODULE 1 PRODUCT GENERAL LED MODULE Voltage 100 250V 50 60Hz Rated Power IP 180W IP67 protection rating LED Unit 48pcs 12 xRED 12x GREEN 12 x BLUE 12 x WHITE Output LED Environment Temperature Cooling Dimensions 20 C 40 C Direct air convection 305 x 276x 280mm Weight 8 5Kg 2008 8 13 1 4 4 3931 1010 482 274 186 LUX 2 1 0 1 2 9 2 4 6 8 10Distance m 4 6130 1700 776 450 304 LUX 2 1 0 2 1 2 3 2 4 6 8 10Distance m 4 1360 256 120 68 46 LUX 2 1 5 1 2 3 2 4 6 8 10Distance m 4613 1204 552 326 230 LUX 3 2 1 2 1 2 3 2 4 6 8 10Distance m 11340 2885 1285 765 530 LUX 3 T 2 1 o P 2 1 2 2 4 6 8 10Distance m RGB WHITE 16300 4000 1900 1122 752 LUX gt T 1 o 0 E 1 2 2 4 6 8 10Distance
16. r will be made by the actual RGB values onthe CAL2 3 13 ACTIVATE THE PASSWORD MENU gt KEY e Enter the KEY mode to selectwhether the accesspassword is onor off e When the fixtureis set asPASS after 30 seconds orturn on thefixture next time the fixture will need an access passwordto enterthe display menu control Note The factory access passwordis UP DOWN UP DOWN then press ENTER to confirm the access 3 DISPLAY PANEL OPERATION 13 2008 8 13 USING ADMX512 CONTROLLER 4 1 BASIC ADDRESSING e Connect all of the unitsin series using standard DMX512 signal cable or the IP65rated cable provided e Set the DMX512 address in the DMX menu e It is possible to have the same DMX address or independent addresses for each fixture 4 2 CHANNEL ASSIGNMENT e Note This product have three DMX512 channel configuration STAG Arc 11 Ar1 d Arc 21 2 1 2 5 and HSV STAG CHANNEL VALUE FUNCTION 1 MASTER DIMMER 0 255 2 RED 0 lt gt 255 STEP TIMEwhen CUS 01 CUS 10 8 is activated 3 GREEN 0 lt gt 255 FADE TIME when CUS 01 CUS 10in CH8 is activated 4 BLUE 0 lt gt 255 5 WHITE 0 lt gt 255 COLOR MACRO 0 lt gt 5 NO FUNCTION 6 lt gt 20 HIGH only when NORMAL POWER mode 21 lt gt 30 FUNCTION 31 lt gt 50 RED 100
17. ted set 5 LED PCB 6 Heat sink 7 Bracket 8 Power connection board 9 Display PCB 10 Display protection metal plate 11 Safety chain board 12 Driver PCB 13 POWER 5V 14 Power supply 24 Version 1 0 5 APPENDIX 24 2008 8 13
Download Pdf Manuals
Related Search