UC864-K Product Description
Contents
1. 4 1 2 Easy GPRS definition The Easy GPRS feature provides a way to replace the need of an Internet TCP IP stack at the terminal equipment side The steps that will be required to obtain a virtual serial connection that is actually a socket to the Internet peer are configuring the WCDMA Access configuring the embedded TCP IP stack behavior defining the Internet Peer to be contacted request the WCDMA and socket connections to be opened host is connected exchange raw data close the socket and WCDMA context All these steps are achieved through AT commands As for common modem interface two logical statuses are involved command mode and data traffic mode e In Command Mode CM some AT commands are provided to configure the Data Module Internet stack and to start up the data traffic e In data traffic mode Socket Mode SKTM the client can send receive a raw data stream which will be encapsulated in the previously configured TCP IP packets which will be sent to the other side of the network and vice versa Control plane of ongoing socket connection is deployed internally to the module For more detailed information regarding WCDMA please consult AT Commands Reference Guide ki ae Te gt Reproduction forbidden without Telit Communications S p A written authorization All Rights Reserved page 24 of 32 5 Telit UC864 K Product Description 80341ST10055a Rev 0 08 05 2009 AT Commands The Telit U2. e TS EMEA telit com e TS AMERICAS telit com TS APAC telit com Or use http www telit com en products technical support center contact php Telit appreciates feedback from the users of our information Technical documentation available for download into the Website www telit com Products gt UMTS HSDPA gt selected model bs od Reproduction forbidden without Telit Communications S p A written authorization All Rights Reserved page 29 of 32 Telit UC864 K Product Description 80341ST10055a Rev 0 08 05 2009 List of acronyms ACM Accumulated Call Meter ASCII American Standard Code for Information Interchange AT Attention commands CB Cell Broadcast CBS Cell Broadcasting Service CCM Call Control Meter CLIP Calling Line Identification Presentation CLIR Calling Line Identification Restriction CMOS Complementary Metal Oxide Semiconductor CR Carriage Return CSD Circuit Switched Data CTS Clear To Send DAI Digital Audio Interface DCD Data Carrier Detected DCE Data Communications Equipment DRX Data Receive DSR Data Set Ready DTA Data Terminal Adaptor DTE Data Terminal Equipment DTMF Dual Tone Multi Frequency DTR Data Terminal Ready EMC Electromagnetic Compatibility ETSI European Telecommunications Equipment Institute FTA Full Type Approval ETSI HF Hands Free HSDPA High Speed Downlink Packet Access IMEI International Mobile Equipment Identity IMSI International Mobile Subscriber
3. Identity IRA International Reference Alphabet ITU International Telecommunications Union IWF Inter Working Function LCD Liquid Crystal Display LED Light Emitting Diode LF Linefeed ME Mobile Equipment MMI Man Machine Interface MO Mobile Originated MS Mobile Station MT Mobile Terminated ee Fe meega forbidden without Telit Communications S p A written authorization All Rights _ _ _ page o of 32 Telit UC864 K Product Description 80341ST10055a Rev O 08 05 2009 OEM Other Equipment Manufacturer PB Phone Book PDU Protocol Data Unit PH Packet Handler PIN Personal Identity Number PLMN Public Land Mobile Network PUCT Price per Unit Currency Table PUK PIN Unblocking Code RACH Random Access Channel RLP Radio Link Protocol RMS Root Mean Square RTS Ready To Send RI Ring Indicator SCA Service Center Address SIM Subscriber Identity Module SMD Surface Mounted Device SMS Short Message Service SMSC Short Message Service Center SS Supplementary Service TIA Telecommunications Industry Association UDUB User Determined User Busy UMTS Universal Mobile Telecommunications System USB Universal Serial Bus USSD Unstructured Supplementary Service Data WCDMA Wideband Code Division Multiple Access 3GPP 3rd Generation Partnership Project ua Go Reproduction forbidden without Telit Communications S p A written authorization All Rights Reserved page 31 of 32 Telit UC864 K Product Descr
4. 864 K module according to the specifications for the class 3 portable terminals WCDMA2 100 is 108 2 dBm typical in normal operating conditions 2 7 Antennas 2 7 1 WCDMA Antenna The antenna that the customer chooses to use should fulfill the following requirements Frequency range WCDMA Band Bandwidth 250 MHz in WCDMA2100 band For further information please refer to the UC864 K Hardware User Guide Reproduction forbidden without Telit Communications S p A written authorization All Rights Reserved page 11 of 32 Telit UC864 K Product Description 80341ST10055a Rev 0 08 05 2009 2 1 2 UC864 K Antenna connectors 2 7 2 1 WCDMA Applications The UC864 K module is equipped with a 50 Ohm RF connector from Murata GSC type P N MM9329 2700B The suitable counterpart is Murata MXTK92 Type or MXTK88 Type 2 8 Supply voltage The external power supply must be connected to VBATT signal and must fulfill the following requirements Nominal operating voltage 3 8 V Operating voltage range 34V 4 2V NOTE Operating voltage range must never be exceeded care must be taken in order to fulfill min max voltage requirements 2 9 WCDMA Power consumption The typical current consumption of the Telit UC864 K is Power off current typical lt 26 uA Stand by current WCDMA Idle lt 22mA lt 4 1mA using command AT CFUN 5 Operating current in WCDMA voice channel lt 690 mA worst network conditions Operating current in WCDMA
5. C864 K module can be driven via the serial interface using the standard AT commands The Telit UC864 K module is compliant with 1 2 3 4 Hayes standard AT command set in order to maintain the compatibility with existing SW programs 3gpp TS 27 007 specific AT command and WCDMA specific commands 3gpp TS 27 005 specific AT commands for SMS Short Message Service and CBS Cell Broadcast Service FAX Class 1 compatible commands Moreover the Telit UC864 K module supports also Telit proprietary AT commands for special purposes For a more information about AT commands supported by UC864 K modules please refer to document AT Commands Reference Guide The AT is an ATTENTION command and is used as a prefix to other parameters in a string The AT command combined with other parameters can be set up in the communications package or typed in manually as a command line instruction Reproduction forbidden without Telit Communications S p A written authorization All Rights Reserved page 25 of 32 Telit UC864 K Product Description 80341ST10055a Rev O 08 05 2009 6 Conformity Assessment Issues The UC864 K module is assessed to the MIC now KCC MATAONG TH8E 9BX3 VYK8 WBFC LEA ASA Certificate of Information and Communication Equipment a 3 a Ba 34 55 Type Registration Certification Type As ET NA FAFA ARY HJAEFYHZE Trade Name or Applicant 7 7 9 HO Al SEAS FAY 717 Equipment Name JE pn o
6. K Product Description 80341ST10055a Rev 0 08 05 2009 The Telit UC864 K supports the IRA characters set International Reference Alphabet in TEXT and PDU mode 211 10 SIM related functions Activation and deactivation of the numbers stored in phone book FDN ADN and PINs are supported Extension at the PIN2 for the PUK2 insertion capability for lock condition is supported 211 11 Call status indication The call status indication by AT commands is supported 2 11 12 Automatic answer Voice Data or FAX After a specified number of rings the module will automatically answer with a beep The user can set the number of rings by means of the command ATSO lt n gt 2 11 13 Supplementary services SS The following supplementary services are supported Call Barring Call Forwarding Calling Line Identification Presentation CLIP Calling Line Identification Restriction CLIR Call Waiting other party call Waiting Indication Call Hold other party Hold Retrieved Indication Closed User Group supplementary service CUG Advice of Charge Unstructured SS Mobile Originated MO 2 11 14 Acoustic signaling The acoustic signaling of the UC864 K on the selected acoustic device are the following Call waiting Ringing tone e SMS received tone LS od U All Rights Reserved page 15 of 32 Telit UC864 K Product Description 80341ST10055a Rev 0 08 05 2009 Busy tone Power on off tone O
7. S e Jeli wireless solutions Making machines talk Telit UC864 K Product Description 80341ST10055a Rev O 08 05 2009 APPLICABILITY TABLE PRODUCT PART NUMBER ki RS eme Ai L Reproduction forbidden without Telit Communications S p A written authorization All Rights Reserved page 2 of 32 Telit UC864 K Product Description 80341ST10055a Rev 0 08 05 2009 Contents T e UR 6 1 1 UC864 K Product SpeclilcaNloN aa a GAAN 8 2 General Product Description 1 11111 nunne nanne nnne n nnne 9 2 1 Dimensions GAAN 9 KC Bn en eS ee A ee ener eer ren ee reeeee ere 10 2 3 Environmental requirements aa 10 2 321 Temperature rang EE 10 2 3 2 Vibration Test non functional maaawa wa wana eee ee ceaeeeceeeeceaeeeseaeeecaaeseeeeeseaeeesaaeessaeeseeeeeesseeseneeenees 10 2 3 3 ele ils Te 10 2 4 Operating E UE TE 11 2 5 Transmitter output TE 11 2 6 Reference SEeNSNININ 0GIG 11 PAT E el E 11 St WODMA ANENA nagana a0 Naa aaa Pd Da a 2 GG PATA GG LA AG EEEE E AA AG 11 24 2 UC864 K Antenna COpteclore aan anan a ANG GA GANA 12 21 21 WCDMAApplication EE 12 ri ga LACE AA 12 2 9 WCDMA Power cansuMp lhk NBA ANAKAN RANA 12 2 10 Embodied Battery ehatrggt esegsessogutesgkseeausseeeEESEESRCENSRSEEEESENEREEERKERREEREhSERKSEEERESEEEEEEKEEK EN 13 2 11 User Dc assassin ede nt died AA 13 2 11 1 Speech Coding AA 13 2 11 2 SIM Reader 13 We SMS AA ee ANA a er ee Aa 14 2 11 4 Real Time Clock
8. a y UC864 K Basic Model Number of Equipment HY S q gi Series Model Number of Equipment ae o Kg TCS UC864 K Certification No d KAP EF FAJA ga ololel zs get Manufacturer and Country of Origin S 4 7 Eg IMT2 IO3TAS1942 8 1977 2T 2132 8 2167 2R0 2G7WD7W Type Identification al TF AH 2 g 20074 Year 074 Month 19 Date Date of Certification 7 Ep Others 9 17 5 BATAN USHA YA NEHA Sys yc It is certified that foregoing equipment has been certificated under the provisions of the Regulations on Certification of Information and Communication Equipment 20074 Year 074 Month 192 Date ANGAT Director General of Radio Research Laboratory Ministry of Information and Communication Republic of Korea NEA Reproduction forbidden without Telit Communications S p A written authorization All Rights Reserved page 26 of 32 Telit UC864 K Product Description 80341ST10055a Rev 0 08 05 2009 Tga WHOS daga SO mic ata ys FAN FAN AA ag MS APSA HAND Acs SH 1 Be If ASAJ ASR MBA HAAD S Li JASA USAR AA FIN MIM 2008 1577 2008 1 31 S 221 2 A KA ASSAD HANDN HA SAK 20 YA RAA Aoi OO ZO HAH ASS Se sgu HSM900 amp QOOMHZCH SAaDOICISAS PA SH Y I J FAHASMH EY DI 2A AFFUS S z E0 SA HAND HAUA 2 E PAMASAHE AHOA FASA SZANS TIES HEOI DEET TE kA OF pea Se Reproduction forbidden without Telit Communications S p A written authorization All Righ
9. and Alarm 100x maaaananaaanaaanas a0 NNNGNG EN NNNGNNNNNAAAENNENNNASKNENNNAEECCNNNAKKCG0NGAGKC 00nn asKK 00nn aNG 14 2 11 5 Data fax Transmission 0 c cccceccecceeceeeeceeeeeceeeeeceaeeeeaeeceaeeeceaeeesaaeseeeeseaeeesaaeeseaeeseeeeeseueeeseneeeeaes 14 2 11 6 Local security management 14 211 7 Call eontrol NN ne ee E NN NNAGNN E E 14 2 11 86 enee EE 14 2 11 9 Characters management 14 2 11 10 SIM related functions GN NNAGNN NN teeter eee tant eeeaaaeeeeeeaaeeeeeeaaeeeseeaeeesesieeeseesaeeeesenaaes 15 2211 11 Gall Status Macato ET 15 2 11 12 Automatic answer Voice Data or FAN 15 2 11 13 Supplementary services GP 15 21114 Acoustic signaling REE R EEAS E 15 EN WE ge e EE 16 2 11 16 RE Transmission Mont na Aa pa AN apn 16 2 12 Logic level specifications Uma III INANI 16 2121 Reser engl aaa Nan MANA NANANG GA AA LA DNA PALAD PANANDA 16 2 13 Audio levels specifications aaa GAGANA ANNA 18 2 14 e 19 a0 Te e M e Reproduction forbidden without Telit Communications S p A written authorization All Rights Reserved page 3 of 32 Telit UC864 K Product Description 80341ST10055a Rev 0 08 05 2009 214 1 Ree ET 19 214 2 DAC Convenente 19 2 15 Mounting UC864 K on your board sssssnnnnsnnunnnnennnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn nnmnnn nnmnnn na 20 2 15 11 ee siana AR Aa E RE E E aaa E a aaa E 20 216 Packing SY TE 21 3 Eval ation Kit onsec a KAANAK EE EE AEE Ei 22 A Software Fe
10. atures ula 23 4 1 Enhanced Easy GPRS Extension nnmnnn nnmnnn nna 23 AAA AA 23 41 2 JEasy GPRS denton EE 24 5 AT COMMandS wi cisececisececetetecccensussecenesenesenswencsuneneseransweweuecssanesareuancwawesseanertsarasewduewasenereades 25 6 Conformity Assessment ISSUeS sssgserseekkessEsssEEEENEEEKESSEREESEEERESEEEEEEREEREEEEEEEREKEKERSEEEEEER 26 7 SAFETY RECOMMENDA TION eege 28 7 1 Contact Information Support ssisiicccicescsiecccie scccssncncesacasceeresaasseewscesasnecnecesreseneneetecseneasencceenecne 29 LIST OF ACrONVINS GAB NAA 30 8 Document Change LOG 32 ke Reproduction forbidden without Telit Communications S p A written authorization All Rights Reserved page 4 of 32 Telit UC864 K Product Description 80341ST10055a Rev 0 08 05 2009 DISCLAIMER The information contained in this document is the proprietary information of Telit Communications S p A and its affiliates TELIT The contents are confidential and any disclosure to persons other than the officers employees agents or subcontractors of the owner or licensee of this document without the prior written consent of Telit is strictly prohibited Telit makes every effort to ensure the quality of the information it makes available Notwithstanding the foregoing Telit does not make any warranty as to the information contained herein and does not accept any liability for any injury loss or damage of any kind incurred by use of or reliance up
11. d and developed by Telit for OEM usage and dedicated to portable data voice and telemetric applications such as Telemetry and Telecontrol SCADA applications Security systems Automated Meter Reading AMR Vending machines POS terminals PDAs and Mobile Computing Phones and Payphones Automotive and Fleet Management applications Battery powered applications needing a battery charger Return channel for digital broadcasting From the interface point of view the UC864 K provides the following e USB2 0 for AT commands Baud rate up to 12 Mbps e Full RS232 UART CMOS level ASCO interface for AT commands Fixed baud rate up to 230 Kbps SIM card interface 1 8 3 volts with auto detection and hot insertion 22 x GPIO ports max 3 x A D converters 1 x D A converter 1 x buzzer output 1 x single led supply output 3 ab h Reproduction forbidden without Telit Communications S p A written authorization All Rights Reserved page 6 of 32 Telit UC864 K Product Description 80341ST10055a Rev 0 08 05 2009 In order to meet the competitive OEM and vertical market stringent requirements Telit supports its customers with a dedicated Support Policy with e Telit Evaluation Kit EVK2 to help you develop your application e A Website with all updated information available e An high level specialist technical support to assist you in your development For more updated information concerning product Roadmap availability tech
12. d the pin 1 are shown in the following picture 26 0015 MOVABLE RF CABLE eee ea es NOTE metal tabs present on UC864 K should be connected to GND page 20 of 32 Telit UC864 K Product Description 80341ST10055a Rev 0 08 05 2009 2 16 Packing system The Telit UC864 K is packaged on trays of Each tray contains 20 pieces with the following dimensions 325 73 161 07 8 4 8 T TIO ts iS 3 LINE 42 77 62 63 LOSSOOO 173 73 42 HL LARLA 63 i a B ra E Si pe SECTION C G 2 5 10 SECTION A A SECTION B 8 Size of the tray is 325 73 x 173 73mm NOTE Trays can withstand the maximum temperature of 65 C Reproduction forbidden without Telit Communications S p A written authorization All Rights Reserved page of 32 Telit UC864 K Product Description 80341ST10055a Rev 0 08 05 2009 3 Evaluation Kit In order to assist you in the development of your Telit UC864 K module based application Telit can supply the EVK2 Evaluation Kit with appropriate power supply SIM card housing RS 232 serial port level translator direct UART connection Handset H
13. data channel lt 680 mA worst network conditions Operating current in HSDPA channel lt 730 mA worst network conditions Reproduction forbidden without Telit Communications S p A written authorization All Rights Reserved page 12 of 32 Telit UC864 K Product Description 80341ST10055a Rev 0 08 05 2009 2 10 Embodied Battery charger The battery charger is suited for 3 7V Li lon rechargeable battery suggested capacity 500 1000mAH The Charger needs only a CURRENT LIMITED power source input and charges the battery directly through VBATT connector pins Battery charger input pin CHARGE Battery pins VBATT GND Battery charger input voltage min 5 0 V Battery charger input voltage typ 5 5 V Battery charger input voltage max 7 0 V Battery charger input current max 400mA Battery type Li lon rechargeable NOTE If embodied battery charger is used then a LOW ESR capacitor of at least 100uF must be mounted in parallel to VBATT pin NOTE when power is supplied to the CHARGE pin a battery must always be connected to the VBATT pin of the UC864 K 2 11 User Interface The user interface is managed by AT commands specified on the ITU T V 250 3gpp 27 007 and 27 005 specifications 2 11 1 Speech Coding The UC864 K voice codec supports the following rates e WCDMA o Adaptive Multi Rate 2 11 2 SIM Reader The UC864 K supports R5 and R99 3gpp TS 31 114 USIM 1 8V and 3V ONLY with an external SIM connector For 5V SIM op
14. eadset and Hands free car kit audio antenna The EVK2 provides a fully functional solution for a complete data phone application The standard serial RS232 9 pin connector placed on the Evaluation Kit allows the connection of the EVK2 system with a PC or other DTE The development of the applications utilizing the Telit UC864 K module must present a proper design of all the interfaces towards and from the module e g power supply audio paths level translators otherwise a decrease in the performances will be introduced or in the worst case a wrong design can even lead to an operating failure of the module In order to assist the hardware designer in his project phase the EVK2 board presents a series of different solutions which will cover the most common design requirements on the market and which can be easily integrated in the OEM design as building blocks or can be taken as starting points to develop a specific one Evaluation Kit For a detailed description of the Telit Evaluation Kit refer to the documentation provided with the Telit UC864 K Hardware User Guide and EVK2 User Manual ec A ER aan forbidden without Telit Communications S p A written authorization All Rights Reserved page 22 of 32 Telit UC864 K Product Description 80341ST10055a Rev 0 08 05 2009 4 Software Features 4 1 Enhanced Easy GPRS Extension 4 1 1 Overview The Easy GPRS feature allows the Telit UC864 K user to contact a device in
15. eration an external level translator can be added page 13 of 32 Telit UC864 K Product Description 80341ST10055a Rev 0 08 05 2009 2 11 3 SMS The UC864 K supports the following SMS types e Mobile Terminated MT class O 3 with signaling of new incoming SMS SIM full SMS read Mobile Originated class 0 3 with writing memorize in SIM and sending e Cell Broadcast compatible with CB DRX with signaling of new incoming SMS 2 11 4 Real Time Clock and Alarm The UC864 K supports the Real Time Clock and Alarm functions through AT commands furthermore an alarm output pin GPIO6 can be configured to indicate the alarm with a hardware line output Furthermore the Voltage Output of the RTC power supply is provided so that a backup capacitor can be added to increase the RTC autonomy 2 11 5 Data fax Transmission The Telit UC864 K supports e WCDMA HSDPA category 8 MS Class A Simultaneous Voice and Data e Fax service Class 1 Group 3 2 11 6 Local security management The local security management can be done with the lock of Universal Subscriber Identity module USIM and security code request at power up 2 11 7 Call control The call cost control function is supported 2 11 8 Phonebook This function allows the storing of the telephone numbers in SIM memory The capability depends on SIM version and embedded memory 2 11 9 Characters management te Reproduction forbidd page 14 of 32 Telit UC864
16. ff Hook dial tone Congestion tone Connected tone Call dropped No service tone Alarm tone 2 11 15 Buzzer output The General Purpose I O pin GPIO7 can be configured to output the BUZZER output signal with only an external MOSFET transistor and a diode a Buzzer can be directly driven The ringing tone and the other signaling tones can be redirected to this Buzzer output with a specific AT command 2 11 16 RF Transmission Monitor As alternate function of the GPIO5 the UC864 K provides the RF transmission monitor When the alternate function is activated the pin of GPIO5 changes to HIGH every time the module transmits an RF signal and remains HIGH for the duration of the transmission sequence 2 12 Logic level specifications Where not specifically stated all the interface circuits work at 2 6V CMOS logic levels To get more detailed information about the logic level specifications used in the Telit UC864 K interface circuits please consult the UC864 K Hardware User Guide 2 12 1 Reset signal Signal Function UO UC864 K pin RESET Phone reset UO 54 RESET is used to reset the UC864 K Whenever this signal is pulled low the UC864 K is reset When the device is reset it stops any operation and after the release of the reset it is unconditionally rebooted without doing any detach operation from the network where it is registered to This behavior is not like a proper shut down because any device is requested to issue a detach reques
17. installation issue because the risk of disturbing the WCDMA network or external devices or having impact on the security Should there be any doubt please refer to the technical documentation and the regulations in force Every module has to be equipped with a proper antenna with specific characteristics The antenna has to be installed with care in order to avoid any interference with other electronic devices and has to guarantee a minimum distance from the body 20 cm In case of this requirement cannot be satisfied the system integrator has to assess the final product against the SAR regulation The European Community provides some Directives for the electronic equipments introduced on the market All the relevant information s are available on the European Community website http europa eu int comm enterprise rtte dir99 5 htm The text of the Directive 99 05 regarding telecommunication equipments is available while the applicable Directives Low Voltage and EMC are available at http europa eu int comm enterprise electr equipment index en htm page 28 of 32 Telit UC864 K Product Description 80341ST10055a Rev 0 08 05 2009 7 1 Contact Information Support Our aim is to make this guide as helpful as possible Keep us informed of your comments and suggestions for improvements For general contact technical support report documentation errors and to order manuals contact your regional Technical Support Center at
18. internet and establish with it a raw data flow over the WCDMA and Internet networks This feature can be seen as a way to obtain a virtual serial connection between the Application Software on the Internet machine involved and the controller of the Telit UC864 K module regardless of all the software stacks underlying An example of the protocol stack involved in the devices is reported Remote Controller Telit Device Device UC864 networks Internet TCP UDP Serial Line Driver network interworking This particular implementation allows to the devices interfacing to the Telit UC864 K module the use of the WCDMA and Internet packet service without the need to have an internal TCP IP stack since this function is embedded inside the module Easy GPRS overcomes some of the known limitations of the previous implementation and implements some new features such as e Keep the WCDMA context active even after the closing of a socket allowing the application to keep the same IP address e Also Mobile terminated incoming connections can be made now it is possible to receive incoming TCP connection requests IG BE Y Cf A a meega forbidden without Telit Communications S p A written authorization All Rights Reserved page of 32 Telit UC864 K Product Description 80341ST10055a Rev 0 08 05 2009 e A new internal firewall has been implemented in order to guarantee a certain level of security on internet applications
19. iption 80341ST10055a Rev 0 08 05 2009 8 Document Change Log Revision Date Changes dd mm yyyy 0 08 05 2009 Initial issue ap SEH Reproduction forbidden without Telit Communications S p A written authorization All Rights Reserved page 32 of 32
20. mmunications S p A written authorization All Rights Reserved page 8 of 32 Telit UC864 K Product Description 80341ST10055a Rev 0 08 05 2009 2 General Product Description 2 1 Dimensions Dimensions UC864 K Length mm 36 2 Width mm 30 Thickness mm 4 8 UC864 K drawing 4 6201 maga B ul tal CLEARANCE FOR a 26 Sf01L5 Ha 2 3 Lal CLOSE COMPONENTS 1158 015 CH 1 a CH D MOVABLE RF CABLE J m E Seil g S ki 1 DV i ei fe A a ap Tei bit t A T q pi g wi SE DY S ii H cn Gin E WU 15 al tr jh J 1 ie 1 Da 30402 A dh L65 KU i lg O 85s01 a L 32 8 0 3 ke Reproduction forbidden without Telit Communications S p A written authorization All Rights Reserved page 9 of 32 Telit UC864 K Product Description 80341ST10055a Rev 0 08 05 2009 2 2 Weight Weight UC684 K 10 gr 2 3 Environmental requirements The Telit UC864 K module is compliant with the applicable 3gpp reference documentation TS 25 101 Release 2004 03 2 3 1 Temperature range UC864 K Note The module is functional in all 20 55 C the temperature range and it fully meet
21. nical characteristics commercial and other issues please check on the Telit website www felt com gt Products UMTS HSDPA gt UC864 Family NOTE Some of the performances of the Telit modules depend on SW version installed on the module itself The Telit modules SW group is continuously working in order to add new features and improve the overall performances The Telit modules are easily upgradeable by the developer using the Telit Flash Programmer bs od Reproduction forbidden without Telit Communications S p A written authorization All Rights Reserved page 7 of 32 PA e tk UC864 K Product Description 80341ST10055a Rev 0 08 05 2009 1 1 UC864 K Product Specification FEATURE ITEM Single Band UMTS HSDPA 2100MHz Data HSDPA UL 384kbps DL 7 2Mbps Service WCDMA UL DL 384kbps 36 2 L X30 W X4 8 T USB 2 0 AT command etc 80 Pin Board to Board connector SIM RF connector External Antenna 64MB SDRAM and 64MB Flash memory e Vocoder Voice UMTS Static Dynamic AMR TUTA Service SIM Card Support 1 8 and 3V UICC UMTS Security Encryption UEA1 integrity UIA e IMEI Security SIM lock Internet TCP IP UDP IP PPP protocol V42Bis data compression Protocols e SVD Simultaneous Voice and Data e SIM SAN aba Book Management Applications FDN dialing number Service dialing number e Enhanced operator name string eee Reproduction forbidden without Telit Co
22. on the information Telit disclaims any and all responsibility for the application of the devices characterized in this document and notes that the application of the device must comply with the safety standards of the applicable country and where applicable with the relevant wiring rules Telit reserves the right to make modifications additions and deletions to this document due to typographical errors inaccurate information or improvements to programs and or equipment at any time and without notice Such changes will nevertheless be incorporated into new editions of this application note All rights reserved 2009 Telit Communications S p A Ba forbidden without Telit Communications S p A written authorization All Rights Reserved page 5 of 32 Telit UC864 K Product Description 80341ST10055a Rev 0 08 05 2009 1 Overview The Telit UC864 K module are small lightweight low power consumption and RoHS compliant devices that allow digital communication services wherever a WCDMA HSDPA network is present The UC864 K is a low cost connector less best solution for medium to high quantity projects The UC864 K is provided with an 80 pin Molex board to board connector and a 50 Ohm Murata RF connector The UC864 K module includes features like HSDPA 7 2Mbps Voice Circuit Switched Data transfer Fax Phonebook and SMS support embedded TCP IP stack and battery charging capabilities The UC864 K is specifically designe
23. s the ETSI specifications Operating temperature The module is functional in all 30 80 C the temperature range Temperatures outside the range 20 C 55 C might slightly deviate from ETSI specifications Temperature in not functional conditions aoe Oe Functional the module is able to make and receive voice calls data calls SMS and make data traffic 2 32 Vibration Test non functional e 10 12Hz ASD 1 92m2 s3 e 12 150Hz 3dB oct 2 3 3 RoHS compliance As a part of Telit corporate policy regarding environmental protection the UC864 K comply with the RoHS Restriction of Hazardous Substances directive of the European Union EU Directive 2002 95 EG a e Reproduction forbidden without Telit Communications S p A written authorization All Rights Reserved page 10 of 32 Telit UC864 K Product Description 80341ST10055a Rev 0 08 05 2009 2 4 Operating Frequency The operating frequencies in WCDMA HSDPA are conformed to the WCDMA and 3gpp specifications TX RX Mode Freq TX MHz Freq RX MHz Channels ARFC offset Tx 9612 9888 WCDMA 2100 1922 4 1977 6 2112 4 2167 6 Rx 10562 10838 190MHz 2 5 Transmitter output power WCDMA2100 The Telit UC864 K transceiver module in WCDMA 2100 operating mode is class 3 in accordance with the specifications which determine the nominal 0 25W peak RF power 24dBm on 50 Ohm 2 6 Reference sensitivity WCDMA2100 The sensitivity of the Telit UC
24. t on turn off For this reason the Reset signal must not be used to normally shutting down the device but only as an emergency exit in the rare case the device remains stuck waiting for some network response NG Reproduction forbidden without Telit Communications S p A written authorization All Rights Reserved page 16 of 32 Telit UC864 K Product Description 80341ST10055a Rev O 08 05 2009 The RESET is internally controlled on start up to achieve always a proper power on reset sequence so there s no need to control this pin on start up It may only be used to reset a device already on that is not responding to any command NOTE do not use this signal to power off the Telit UC864 K module Use the ON OFF signal to perform this function or the AT SHDN command To turn off UC864 K first of all you MUST cut off supplying power to the USB_VBUS or the module does not turn off WS CT Ju ke t Reproduction forbidden without Telit Communications S p A written authorization All Rights Reserved page 17 of 32 Telit UC864 K Product Description 80341ST10055a Rev 0 08 05 2009 2 13 Audio levels specifications The audio of the UC864 K is organized into two main paths e internal path called also MT e external path called also HF These two paths are meant respectively for handset and headset hands free use The UC864 K has a built in echo canceller and a noise suppressor tuned separately for
25. the two audio paths for the internal path the echo canceller parameters are suited to cancel the echo generated by a handset while for the external audio path they are suited for a hands free use For more information on the audio refer to the UC864 K Hardware User Guide Reproduction forbidden without Telit Communications S p A written authorization All Rights Reserved page 18 of 32 Telit UC864 K Product Description 80341ST10055a Rev 0 08 05 2009 2 14 Converters 2 14 1 ADC Converter The on board ADCs are 8 bit converter They are able to read a voltage level in the range of 0 2 volts applied on the ADC pin input store and convert it into 8 bit word Min Max Units Input Voltage range 0 2 0 Volt AD conversion 8 bits Resolution lt 10 2 mV 2 14 2 DAC Converter The on board DAC is a 16 bit converter able to generate an analogue value based on a specific input in the range from O up to 65535 but recalibrated in the range from O to 1023 However an external low pass filter is necessary See the HW User Guide for the details Min Max Units Voltage range filtered 0 2 6 Volt Range 0 1023 Steps 8 E D s Reproduction forbidden without Telit Communications S p A written authorization All Rights Reserved page 19 of 32 Telit UC864 K Product Description 80341ST10055a Rev 0 08 05 2009 2 15 Mounting UC864 K on your board 2 15 1 UC864 K The position of the Molex board to board connector an
26. ts Reserved page 27 of 32 Telit UC864 K Product Description 80341ST10055a Rev 0 08 05 2009 7 SAFETY RECOMMENDATIONS READ CAREFULLY Be sure the use of this product is allowed in the country and in the environment required The use of this product may be dangerous and has to be avoided in the following areas LI Where it can interfere with other electronic devices in environments such as hospitals airports aircrafts etc Q Where there is risk of explosion such as gasoline stations oil refineries etc It is responsibility of the user to enforce the country regulation and the specific environment regulation Do not disassemble the product any mark of tampering will compromise the warranty validity We recommend following the instructions of the hardware user guides for a correct wiring of the product The product has to be supplied with a stabilized voltage source and the wiring has to be conforming to the security and fire prevention regulations The product has to be handled with care avoiding any contact with the pins because electrostatic discharges may damage the product itself Same cautions have to be taken for the SIM checking carefully the instruction for its use Do not insert or remove the SIM when the product is in power saving mode The system integrator is responsible of the functioning of the final product therefore care has to be taken to the external components of the module as well as of any project or
Download Pdf Manuals
Related Search