STD-402 STEP Motor driver User manual
Contents
1. position HALF step mode 0 9 step 400step rev F JP1 at F position FULL step mode 1 8 step 200step rev Out current adjustment Rotate VR1 to adjust maximal output current uro Geel SE E ESBR Ziel a i Jeb iil TAILY AUTOMATION CO LTD gi STD 402 STEP Motor driver User manual 4 INPUT SIGNALS STD 402 with three input signals PUS DIR CO PUS J Pulse input DIR Direction input Page 3 of 5 CO when this input is low lever the driver will turn of output current to free the step motor from excitation condition CONTROLLER STD 402 V V t5 PUS 7 PUS 1 220R 20mA MAX DIR R DIR 3 220R 20mA MAX CO R CO 4 220R I 20mA MAX OV Signals wave T1 T2 T4 20us min T3 2us max HEU cencaieso Sea asc MU Eccc dee COW DIR L 0 0 5V H 4 5V _ CW PUS L 0 0 5V T3 T1 TS T2 T4 Mauro ORSWBHCSRZAS G i Jeb iil TAILY AUTOMATION CO LTD gi STD 402 STEP Motor driver User manual Page 4 of 5 5 INSTALLATION AND WIRING Requirement and Safety precautions 1 The driver should be operated in an environment that is protected from moisture corrosive gases oil mist and airborne dust metallic particles 2 Make sure all connectors are connected to correct position before turn on power Do not connect or disconnect connectors while power is applied to the driver 3 Make sure that the power source supplies the correct voltage and2. TAILY AUTO STD eee M driver AR ser manua ora DOC NO 050331 Page 1 of 5 1 INTRODUCTION The STD 402 stepper motor driver is bipolar PWM chopper constant current regulated unit designed to operate with a wide range of step motors Manufactured by TAILY AUTOMATION Is suitable to drives 2 or 4 phase step motor the driver is high torque easy to interface and use high performance and low cost 2 SPECIFICATIONS Suitable motor 2 or 4 phase stepper motor Control mode Bipolar PWM constant current regulation Drive current 2A MAX T Full step 2 phase excitation Excitation mode w Half step 1 2 phase excitation Power input AC30V 50 60HZ or DC40V 100VA Selection Full step Half step selection Standby current Automatically reduce at standby mode Current adjustment Maximal output current adjust Input signals DIR Direction input COU Current off input PUS Pulse input Ambient temperature 0 C 40 C Dimension 86 W x75 D x35 H mm Weight 120g TAILY lt lt SMBS SEN LSIRDEI om TAILY AUTOMATION CO LTD gi STD 402 STEP Motor driver User manual Page 2 of 5 3 DESCRIPTION ee PI aa THA LNO m eNO STD 402 No NAME DESCRIPTION FACTORYSET s tb Permis 4 ow Puse input connec s ow Stepmotor connector e cs Power input connector Step mode selection H JP1 at H
3. is capable of supplying the required current to the driver Connectors 402 CN1 o2 Z 5 900mm SI 402 CN4 Oo z AR 900mm 402 CN5 900mm i Wiring diagram Controller Lovag CO O DIR ag JP B PUS OLED F CI CN1 3j A CN4 ER E C POWER AC 30V or DC 40V E ee STD 402 Skew CARAS Er TAILY AUTOMATION CO LTD Page 5 of 5 gi STD 402 STEP Motor driver User manual 6 DIMENSION i mde 75 0 86 0 l 13 0 i N M4 X 2 22 0 13 0 I 1 26 0 47 0 uro Geel SE E ESBR Ziel a i Jeb iil TAILY AUTOMATION CO LTD
Download Pdf Manuals
Related Search