User`s Manual for 900 MHz Digital Spread Spectrum Cordless
Contents
1. When you hear a dial tone dial the number you re calling Answering a Call e Ifthe handset is in the base lift the handset The PHONE light goes on and the call is connected e Ifthe handset is away from the base press PHONE or any key on the handset including The PHONE light goes on and the call is connected Ending a Call e Ifyou are near the base place the handset in the base e Ifyou are away from the base press PHONE Redial The last number dialed up to 32 digits on this phone is stored in redial memory until you dial another number 1 Press and wait for the PHONE light to go on 2 When you hear a dial tone press Mute The Mute feature allows you to hear your caller but prevents the caller from hearing you While on acall Press To continue your conversation with the caller Press again Ringer Controls Handset Ringer Volume In standby mode adjust the handset ringer volume by pressing VOLUME 4 on the handset to increase volume or VOLUME Y to decrease Base Ringer Volume Set the Ringer ON OFF switch on the back of the base to ON if you want the base to ring then press VOLUME a or VOLUME Y on the front of the base to select high or low ringer volume Set the switch to OFF if you don t want the base to ring When the Base Ringer is OFF the base won t ring but the IN USE light will flash when a call is coming in Ringer Selection You can choose from four different r2. Alsi lip User s Manual for 900 MHz Digital Spread Spectrum E Cordless Telephone 9400 2g p Wy ANY i Fold open this manual for information about this telephone s installation and operation Please read Part I Important Product Information included in this package W W 2 v Part 2 1998 Philips Consumer Communications L P All rights reserved Printed in China 848233136 Issue 2AT amp T INSTALLATION Modular wall jack AC Adapter Dial mode switch T or P RINGER ON OFF Telephone line cord Power cord Table Desk Installation e Position the battery cover by sliding it on its track up over 1 Choose a spot near an electrical outlet and a telephone jack the battery compartment until it snaps firmly in place This phone requires a modular wall jack and a standard 8 Charge the handset battery for at least 14 hours electrical outlet 110V AC Turn the handset power OFF Charge the handset battery with the handset face down in the base for at least 14 hours After this initial charge you can charge the handset battery with the power set to ON 9 Check for dial tone After the batteries are charged pick up the handset and set the POWER switch to ON Press PHONE the PHONE light should go on and you should hear a dial tone 2 Connect the telephone line cord Plug one end of the telephone line cord into the jack on the back of the base Plug the other end of the line cord into a wall jack Make su
3. MORY This cordless phone can store 20 telephone numbers that you can dial by pressing Mem and the two digit memory location Storing Memory Numbers 1 Make sure the phone is on but not in use 2 Press MEM 3 Enter the telephone number you want to store up to 16 digits 4 Press MEM 5 Enter the two digit memory location 01 to 20 The hand set beeps twice to indicate the number has been stored For example to store 555 1234 in memory location 09 Press MEM 5 5 5 1 2 3 4 MEM 0 9 Dialing Memory Numbers 1 Press PHONE 2 Press MEM 3 Press the two digit memory location 01 to 20 where the number is stored For example to dial the number stored in location 09 press PHONE MEM 0 9 OPERATIN This cordless telephone operates at a power range allowed by the Federal Communications Commission FCC In fact this phone operates in a range that is approximately twice that of a 46 49 MHz cordless phone Even so the handset and base can commu nicate over only a certain distance which can vary with the locations of the base and handset the weather and the construc tion of your home or office For best performance keep the base antenna upright If the phone is out of range of the base you will hear short beeps every 16 seconds in standby mode If you are out of range the NOTE You may wish to write memory dial numbers on the directory card on the base Storing Num
4. ase is paged from handset and Intercom is in use CHARGING light goes on to show handset battery is charging Adjust speaker volume while on an intercom call or adjust base Ringer volume Page the handset 2 After you hang up the phone automatically returns to dial pulse rotary dialing Page Intercom Page Handset from Base 1 Press PAGEHANDSETLOCATOR On the base The INTCM light on the handset goes on 2 Press Tem on the handset to respond to the page 3 When finished press PAGEHANDSET LOCATOR On the base or press TCM on the handset If you re paged at the handset while you re on a call press NTCM The call is put on hold and the PHONE light flashes rapidly To end the intercom conversation so you can return to the call the person at the base must press P GEHANDSETLOCATOR If you press NTCM on the handset you will disconnect your call Page Base from Handset 1 Press w7cm on the handset The base sounds two short beeps and the PAGEMANDSETLOCATOR light on the base goes on 2 Speak to the person at the base through the handset 3 Press ivTcm on the handset or PAGE HANDSET LOCATOR on the base when you are finished Handset Locator If you misplace the handset you can press PAGEHANDSETLOCATOR On the base to make the handset beep The sound will continue for 15 seconds or until you press PAGEHANDSETLOCATOR On the base again or press w7cm on the handset to enter intercom operation ME
5. bers Just Dialed Whenever you make a telephone call you can store the number you dialed in memory Press REDIAL instead of entering the tele phone number in Step 3 when Storing Memory Numbers Replacing a Stored Number You can replace a stored number by storing a new number in its place Storing a Pause in a Memory Number When storing a number in memory press REDIAL where you want a dialing pause Pressing REDIAL more than once inserts a longer pause For example to store 9 PAUSE 555 1234 in memory location 03 Press MEM 9 REDIAL 5 5 5 D 2 3 4 MEM 0 3 G RANGE LOW BATT light continues to flash and you are unable to make a call If you try to place a call while you re out of range the phone will sound an error beep If you move out of range during a phone conversation you will hear short beeps every four seconds To improve reception move closer to the base If you move out of range while on a call the phone will be left off the hook To hang up properly walk back into range periodically pressing PHONE until the PHONE light goes off IN CASE OF DIFFICULTY If you have difficulty operating this phone try the suggestions below If you still have trouble call 1 800 722 9125 Phone Does Not Work At All e Make sure the POWER ON OFF switch is set to ON e Make sure the power cord is plugged into the base and an electrical outlet e Make sure the telephon
6. directions for wall mounting on Existing Wall Plate Use either the long or short line cord depending on how far you are from the phone jack Belt Clip If you wish you can attach the belt clip to the cordless handset using the illustration below ay BATTERIES Charging the Handset Battery Pack The battery pack needs charging when e The phone beeps periodically e The LOW BATT light on the handset flashes e The phone does not respond when you press PHONE and no lights go on Place the handset face down in the base so the CHARGING light goes on The battery pack will be fully charged in 14 hours The handset can be ON or OFF while the battery pack is charging To increase the life of the battery pack allow the battery to discharge fully before charging A fully charged battery maintains standby power for up to 7 days and up to 4 hours of continuous talk time when the handset is on and not in the base If it s more convenient for you you can leave the handset in the base all the time It is impossible to overcharge the batteries If you get a low battery indicator even after 14 hours of charging the battery should be replaced CAUTION To reduce the risk of fire or damage to A persons or damage to the telephone read and follow these instructions carefully e Use only replacement battery 3094 e Do not dispose of the battery in a fire The cell might explode Check with local codes for special disposal instruction
7. e line cord is plugged firmly into the base unit and the telephone wall jack e If the phone does not beep when you press PHONE the batteries might need recharging e If the handset LOW BATT light flashes the batteries need recharging e Make sure the battery pack is installed correctly e If the battery pack will not charge replace it with replacement battery 3094 e Place the handset in the base for 5 seconds to reset the security code e Unplug the base from the electrical outlet wait 10 seconds then plug the base back in No Dial Tone Check all the previous suggestions If you still do not hear a dial tone disconnect the phone and try another phone in the same wall jack If there is no dial tone on that phone either the problem is probably in your wiring or local service Call your local telephone service company Noise or Interference e You may be out of range Move closer to the base e Household appliances plugged into the same circuit as the base can sometimes cause interference Try moving the appliance or the base to another outlet e The layout of your home or office might be limiting the operating range Try moving the base to another location preferably on an upper floor Error Tone If you hear an error tone and do not get a dial tone when you press PHONE try again Phone Does Not Ring e Make sure the Handset and Base Ringers are set to ON and are at an audible level e Make sure the telephone li
8. inging options Your selected setting affects both the handset and the base 1 Make sure the phone power is set to ON but the phone is not in use OPERATION 2 Press FLASH then press a number button from 1 to 4 3 The handset gives a sample of the ringing option you have selected Handset Receiver Volume Control To adjust listening volume repeatedly press VOLUME a or VOLUME Y on the handset during a call Speaker Volume Control For intercom calls adjust the speaker volume by pressing VOLUME a on the base to increase volume or VOLUME to decrease Flash Press FLASH to activate custom calling services such as Call Waiting or 3 Way Calling You may have to press other buttons before or after FLASH as explained in custom calling instructions provided by your local telephone service company Temporary Tone NOTE If you have touch tone service you do not need to use the Temporary Tone feature If you have dial pulse rotary service this feature allows you to enter codes or tones needed to operate answering machines or use electronic banking services calling cards and other special ser vices however some services may actually require a touch tone line To be sure ask the company that provides the special service 1 Dial the call then press Any buttons pressed after this send touch tone signals Keep base antenna upright IN USE light goes on when line is in use INTCM light goes on when b
9. ket Step 2 Reverse the bracket and re install it Step 4 LINE jack on the back of the base Plug the round con nector on the power cord into the POWER A jack on the back of the base Reverse the bracket and re install it e Turn the wall mounting bracket so the ribbed tabs are facing the front of the unit e Snap the bracket into the guides to lock it in place Connect the other end of the telephone line cord to the wall jack plug and plug the power cord into a standard electrical outlet Mount the base on the wall plate Align the holes in the wall mounting bracket with the hooks on the wall plate and slide the base down until it locks in place Follow Steps 4 to 9 in Table Desk Installation Wall Installation Ms Existing Wall Plate Choose a spot near an electrical outlet and a telephone jack This phone requires a modular wall jack and a standard electrical outlet 110V AC Remove the bracket see Step 2 above and use it to mark the position of the two screws that you will use e It s best to mount the base on wall studs e Hold the bracket up to the wall with the thicker end facing the floor and mark the wall through the screw holes in the bracket e Screw two one inch screws into the spots you marked Connect the telephone line cord to the base Step 3 Align the base with the hooks or screws and slide down into place Step 7 leaving 3 16 extending from the wall 3 Follow the
10. ne cord is connected firmly to the base and the telephone wall jack Make sure the power cord is plugged into an outlet not controlled by a wall switch e You might be too far from the base Move closer e You might have too many extension phones on your telephone line to allow all of them to ring Try unplugging some of the other phones You Hear Other Calls Disconnect the base from the telephone wall jack and plug in a corded telephone If you still hear other calls the problem is prob ably in your wiring or local service Call your local telephone service company Telephone Misdials e It might take a few seconds for your handset to find a good connection to the phone system e If you have dial pulse rotary service make sure the Dial Mode switch is set to PULSE e Ifyou have touch tone service and you hear strange clicks while you are dialing you ll need to set the Dial Mode switch to TONE Noise in the Handset and Buttons Don t Work The base unit and handset might not be set to the same security code Place the handset in the base for at least 5 seconds to reset the security code iil BATT Light is On or Flashing Place the handset in the base make sure the CHARGING light goes on and charge the handset battery pack for at lease 14 hours e If the LOW BATT light is flashing quickly you are out of range of the base Move closer
11. re the plug snaps firmly in place 3 Plug in the power cord Plug the round connector of the AC adapter into the back of the base and the other end into an electrical outlet 4 Set the dial mode switch Set the switch to TONE if you have touch tone service or to W a ns ta lati on PULSE if you have dial pulse service Existing Wall Plate 5 Position the antenna Follow the directions below if you have an existing wall plate Rotate the base antenna until it is upright Use the short telephone line cord 6 Select the Ringer volume See Ringer Controls in the OPERATION section of 1 Choose a spot near an electrical outlet and a telephone jack this manual This phone requires a modular wall jack and a standard 7 Install the handset battery electrical outlet 110V AC For an illustration of battery installation see BATTERIES 2 Remove the wall mounting bracket e Remove the handset battery cover by pressing down at Push in on the ribbed tabs facing the back of the base and the center of the top of the cover and then sliding it off remove the mounting bracket See the illustration on page 2 e Remove the battery from the envelope 3 Connect the telephone line cord and the power cord to e Snap the battery with the charge contacts facing down the telephone base into the battery compartment e Plug one end of the short telephone line cord in the TEL 7 INSTALLATION With Existing Wall Plate Push in on tabs and remove brac
12. s e Do not open or mutilate the battery Released electrolyte is corrosive and may cause damage to the eyes or skin It may be toxic if swallowed e Exercise care in handling batteries in order not to short the battery with conducting materials such as rings bracelets and keys The battery or conductor may overheat and cause harm e Charge the battery provided with or identified for use with this product only in accordance with the instructions and limitations specified in this manual Replacing the Handset Battery Pack 1 Usea coin to pry the edge of the battery pack from the battery compartment then lift it out 2 Align the battery contacts as shown below then snap the new battery in place and replace the cover Receiver Ringer Volume Control NI Redial last number called Make answer or end a call Store access numbers in telephone memory Temporary Tone REDIAL RINGER i ON OFF OPERATION LOW BATT light shows battery power is low Make or respond to intercom call Access phone company subscriber services Prevent caller from hearing you Turn handset RIGNER ON or OFF Power ON OFF In order to use this phone you must make sure the POWER ON OFF switch on the handset is set to ON You can save battery power in the handset when the switch is set to OFF but you will be unable to make or answer calls Making a Call 1 Press and wait for the PHONE light to go on steadily 2
Download Pdf Manuals
Related Search