LCD THERMO PRODUCTS USER MANUAL
Contents
1. 32 ENGLISH Extraflame MONTHLY MELINDA IDRO Remove the ash deposited in the upper part of the furnace wall see figure below ROUTINE MAINTENANCE PERFORMED BY QUALIFIED TECHNICIANS Routine maintenance must be performed at least once a year Since the generator uses pellets as its solid fuel it requires an annual routine maintenance operation which must be performed by a qualified technician using original spare parts only Failure to comply with the above can compromise the safety of the appliance and void the guarantee conditions Complying with the cleaning intervals dedicated to the user described in the use and maintenance manual will guarantee the correct combustion by the generator over time avoiding any malfunctioning and or failures which could require further intervention by the technician Routine maintenance requests are not covered by the product guarantee DOOR GASKETS ASH DRAWER AND BURN POT Gaskets guarantee the hermetic seal of the stove and its ensuing correct operation They must therefore be checked regularly should they be worn or damaged replace them immediately This must be performed by a qualified technician CONNECTION TO THE CHIMNEY Suction and clean the flue duct leading to the chimney once a year or whenever necessary If the installation entails horizontal flue duct sections sucti2. Room air fan disassembly and removal of dust and debris of any pellets Check air intake pipe and cleaning of the flow sensor 900 IN ES S IS IS IS 34 ENGLISH Extraflame DISPLAYS to an external thermostat DISPLAY REASON MEANING START The start phase is in progress the continuous feeding of the pellets PELLET FEEDING during the ignition phase is in _ progress IGNITION The ignition phase is in progress START UP The start up phase is in progress u BURN POT The automatic burn pot cleaning is in CLEANING progress FINAL CLEANING The final cleaning is in progress 2 Every time the stove displays one of the alarms listed above it will switch STAND BY Start up attempt while the stove is still Gir automatically UM COOLING The alarm can only be released using button 1 when it switch off has been completed The stove can only be switched back on when it completely cold The normal operating phase is in WORK progress the stove is operating at the set power MODULATION the stove is operating at minimum STAND BY Stove off waiting for re ignition due The stove will only re start when the external thermostat will request it STDBY BLACK OUT ROOM T The stove is cooling after a power cut Displays room temperature in the models where provided Once cooling is complete i
3. class or level of corrosion and specification of the materials constituting the inner wall in contact with the fumes soot fire resistance class minimum distance from combustible materials Where due to high efficiency a pellet stove has fumes at a temperature of less than 160 C ambient see technical data it must be resistant to moisture The installer of the fumes exhaust system once the installation is complete and the relevant checks and inspections have been made must fix the chimney plaque supplied by the manufacturer with the product in a visible manner near the fireplace and which must be completed with the following information 9999 ENGLISH 13 Extraflame nominal diameter distancefrom combustible materials indicated in millimetres followed by the arrow and flame symbol installer data and date of installation Every time one must cross combustible materials the following indications must be complied with a gt N f gt ZZ 1 1 o J 1 SYMBOL DESCRIPTION QUOTAIMM b Minimum distance of combustible materials from the intrados of the framework floor wall 500 b 1 Minimum distance of combustible materials from the extrados of the framework floor 500 a Minimum distance from combustible materials defined by the manufacturer G xxx The single wall pipes are indicated
4. It is possible to select the preferred language to display the various messages SET LANGUAGE CONTROLS PROCEDURE ITALIAN ENGLISH Press key 6 until the text SET CLOCK appears LANGUAGE GERMAN Press key 2 twice until SET LANGUAGE FRENCH Confirm using key 6 SPANISH Select the language using key 4 o 5 Confirm using key 6 then key 1 to exit the Menu DO NOT ALLOW THE BAG OF PELLETS TO COME INTO CONTACT WITH THE BOILING HOT STOVE DURING THE FILLING PHASE 5 DO NOT USE ANY INFLAMMABLE LIQUIDS FOR IGNITION IN THE EVENT OF CONTINUOUS NO IGNITION CONTACT AN AUTHORISED TECHNICIAN NO IGNITION FIRST IGNITION COULD EVEN FAIL AS THE AUGER IS EMPTY AND IS NOT ALWAYS ABLE TO LOAD THE BURN POT ia WITH THE REQUIRED AMOUNT OF PELLETS ON TIME TO REGULARLY START THE FLAME IF THE PROBLEM OCCURS AFTER ONLY A FEW MONTHS WORKING CHECK THAT ROUTINE CLEANING STATED IN THE STOVE BOOKLET HAS BEEN CARRIED OUT CORRECTLY CLEAN CHECK UP 1 2 BURN POT BOTTOM SHOULD THE CLEAN CHECK UP ALARM BE TRIGGERED MAKE SURE THAT THE BOTTOM OF THE BURN POT IS FREE FROM RESIDUES OR SCALES THE HOLES AT THE BOTTOM MUST BE COMPLETELY FREE TO GUARANTEE CORRECT COMBUSTION PELLET FEED ADJUSTMENT TO ADJUST COMBUSTION ACCORDING TO REQUIREMENTS IF THE ALARM PERSISTS AND THE ABOVE LISTED CONDITIONS HAVE BEEN CHECKED CONTACT THE QUALIFIED AFTER SALES ASSISTANCE CENTRE ENGLISH 23 OExtraflame FUNCTIONING
5. cccssssssssssssscesssssssssscssssssesssesscessessonse 25 ADDITIONAL THERMOSTAT FUNCTIONING WITH STBY ACTIVE 25 ADDITIONAL THERMOSTAT OPERATION WITH DEACTIVATED STBY sssssssssssssssssssssssccssessssssecssssosssssssssssessssessssnseesssessssnsesrsssssssnssessnsessssessssnseesssessesseesess 25 5 25 AUX 25 USER MENU 26 SET THERMOSTAT 26 FAN e 26 ge r r 26 PELLET m 26 VARAN S RP 27 SUAN DAAE 99998 Ns ELS ED D M 27 KEVS Mf N N D 28 ES M EN 28 AIR DISCHARGE 28 CHRONO 28 DBOSIGRAMMIDISIESANIDISEBA W RAMA o 29 CLEANING AND MAINTENANCE 30 MAINTENANCE DA 30 CLEANING AND MAINTENA
6. pump deactivated On pump active Flashing the safety device is active H2O temperature gt 85 C IMA ENGLISH Extraflame GENERAL MENU bh 1 GO BACK EXIT 22 32 BROWSE PARAMETERS NEXT 2 PREVIOUS 3 5 435 MODIFY SETTING DATA INCREASE 4 DECREASE 5 6 CONFIRM ACCESS MENU SET CLOCK KO SET CHRONO ENABLE CHRONO DAY u p LANGUAGE H 6 9 ILENFRDEES gt wure START PRG1 HOURS ET THERMOSTAT USER gt Ud STOP PRG1 MINUTES Y Y gt ENABLE MONDAY PRGI ON OFF ON OFF DISPLAY SUNDAY PRG1 ON OFF Y TECHNIC SET RESERVED TO THE QUALIFIED PELLET SET PRG1 TECHNICIAN i 75 C 2 V1 FAN 200 THE OTHER 5 Y STAND BY ON OFF e KEYS LOCKED ON OFF e RESET ON OFF BASIC INSTRUCTIONS The following recommendations must be followed the first Before igniting the stove the following points must be times the stove is ignited verified Itis possible that slight odours are produced due tothe hydraulic system must be finished in compliance drying of the paints and silicones used Avoid staying in the with the standards and with the indications of this manual room for a long time T
7. ACCORDING TO THE STANDARD 6 COMMISSIONING CHECKS sursonesnrennesnnennssnnssnssnussnennnssnnenussnnssnnnnnssnnsnunsnnnsunsnnnsnnennnsnnssnnsnnssnnsnnnsnnssnnsnnesnnennssnnennssnnssnnsnussnsnsnssnnennssnnssnnsnnnsnnnnen 6 AUTOMATIC THERMOSTATIC MIXER VALVE en 6 HYDRAULIC PLANT BASIC LAYOUT eere 7 ELISIR IDRO HYDRAULIC CONNECTIONS 8 INSTANT DOMESTIC HOT WATER PRODUCTION KIT 9 51 5 etm e 9 9 PRODUCTS FEATURES 9 DEVICES sosssiss sososeisosssissosasssess ossiss ss 10 REFERENCE STANDARDS 10 GENERAL 11 INSTALLATION 12 INSERTS INSTALLATION e 12 FUMES EXHAUST SYSTEM 13 GENERAL REQUIREMENT cep 13 jede 14 lif 16 sse 5 16 COMBUSTION PRODUCTS OUTEET QUOTA sezme vaaz lense spain Er sim akl
8. cycle water movement causes the displacement of air bubbles and their out flow from the automatic vents out of the system This can cause the pressure to drop and activate the minimum pressure switch which stops the motor that transports the pellets and therefore the heat generator Vent out the system if necessary even multiple times to remove the air and reload it if the pressure is too low It is not a malfunction but a normal occurrence due to its filling After filling the plumber must always thoroughly vent the system using the special vents in the circuit and running the air breather function on the machine After the first ignition and with a cold machine re activate the function air breather see chapter OTHER FUNCTIONS BULB THERMOSTATS RESET Check by pressing the reset buttons 85 100 C located on the back of the appliance before contacting a technician see section RESET ENGLISH 19 Extraflame CONTROL BOARD BUTTON DISPLAY OF VARIOUS TO ACCESS ON OFF TEXT MESSAGES THE MENU OPERATING POWER TEMPERATURE ADJUSTMENT SETTING DISPLAY ICONS Indicates the receipt ofthe radio signal On during radio communication Off no radio communication Flashing excluded serial port Indicates the stove modulation On the stove is working at the set power Flashing the power at which the stove is working is different to the power set the stove is modulating for various reasons Indic
9. ducted combustion air taken from the outside Installation premises requirements The support surfaces and or points must have a suitable load bearing capacity to support the weight of the appliance of the accessories and coatings The adjacent side and rear walls and the supporting surface must be made of non combustible material Installation near combustible materials or those sensitive to heat is permitted as long as there is a suitable safety distance which for pellet stoves is equal to REFERENCES INFLAMMABLE OBJECTS NON INFLAMMABLE OBJECTS A 200 mm 100 mm B 1500 mm 750mm C 200 mm 100 mm 9 Air inlet Inspection S floor protection figure 1 figure 2 In any case the temperature of the adjacent combustible materials must not reach a temperature equal to or greater than the room temperature increased by 65 C The minimum volume of the premises in which to install the appliance must be greater than 15 m INSERTS INSTALLATION In the event of installation of inserts access to the internal parts of the device is to be prevented and during extraction it should not be possible to access to live parts Any wiring such as a power supply cable or room sensors must be positioned so as not to be damaged during movement of the insert or come into contact with hot parts 12 ENGLISH OExtraflame VENTILATION AND AERATION OF THE INSTALLATION PREMISES Ventilation is deeme
10. empty before filling it 30 ENGLISH Extraflame EVERY DAY Burn pot Remove the burn pot from the relevant compartment and free the holes using the appropriate fire irons supplied remove the ash from the burn pot using a suction device Suck the ash deposited in the brazier compartment Scrapers Cleaning of the heat exchangers allows to guarantee constant heat output through time This type of maintenance must be performed atleast once a day To do this just use the relevant scrapers positioned in the upper part of the stove moving them up and down several times ENGLISH 31 Extraflame WEEKLY Clean the combustion chamber and the ash drawer Empty the ash drawer every week or when required It is recommended to remove the ash in the combustion chamber at least once a week using a suitable vacuum cleaner MONTHLY For the model in the picture below it is recommended to remove the deflector to facilitate cleaning the chamber and the ash drawer
11. increasing the temperature setpoint 5 T DECREASE This button allows decreasing the temperature setpoint 6 CORO D ee Press this button once to enable or disable the chrono This button allows setting the delayed switch off 7 ENABLE DELAYED For example if the stove is set to switch off in an hour it shall switch off SWITCH OFF automatically once the set time elapses displaying the countdown every minute 8 MENU this key provides access to the user and technical menu the technical menu is reserved for assistance 9 INCREASE This button allows increasing the temperature setpoint 10 ESCKEY This key allows the user to exit any program or display and return to the main menu without storing the data 11 REVERSE This button goes back in the display of the various menus 12 CONFIRMATION KEY adjustments made during the user menu 13 FORWARD This key moves forward in the various menus 14 ENABLE F1 FUNCTION Button designed for future applications 15 DECREASE This key decreases the value to be set 16 STOVE STATUS Press this key to view the general status of the stove Note the numbers shown on the remote control are purely explanatory and are not present on the remote control supplied with the product TYPE AND REPLACEMENT OF BATTERIES The batteries are housed in the lower part of the remote control To replace it remove the battery holder as indicated in the figure at the back of the remote control
12. las siyasal ud aee asa 17 FUMES 5 5 5 ea an aaa 17 TECHNICAL INSTALLATION DOCUMENTATION iiaii 2 02 02 ae N clase eR Len Labo egeo cel 18 PELLETS AND FEEDING 19 CHECKS AND PRECAUTIONS FOR FIRST IGNITION 19 THE PELLET LOADING MOTOR DOES 19 CONTROL BOARD ccsscsscssssssssssssessscscesssccsssssessosssssseses 20 plkidFAdISe e M 20 GENERAL MENU 21 BASIC INSTRUCTIONS S 21 THE REMOTE CONTROL 5 22 ENABLE SWITCH OFF Pe r REP Fe er SEDYE e 22 TYPE AND REPLACEMENT 5 22 COMMISSIONING SETTINGS 23 ADJUSTING TIME YEAR 23 ADJUSTING LANGUAGE 23 FUNCTIONING AND LOGIC 24 ADDITIONAL THERMOSTAT
13. of the suitability of the power of the heat generator based on the characteristics of the system verification of the suitability of the installation site verification of the suitability of the fumes exhaust system verification of the suitability of the outside air inlets 9 2 Installation implementation of ventilation and connection to the outer air inlets implementation and connection to the fumes exhaust system assembly and installation electric and hydraulic connections installation of insulation ignition and operation test installation of finishings and coverings 9 9 9 3 Issue of complementary documentation 4 Inspection and maintenance Other actions may be required in relation to specific requests of the competent authority PRELIMINARY ACTIVITIES GENERAL Verification of compatibility of the system of any restrictions required by local administrative regulations special or conventional requirements resulting from condominium regulations constraints laws or administration deeds must precede any other assembly or installation operation One must especially verify the suitability ofthe installation premises of the appliances already installed in the installation premises and in the adjacent and adjoining premises also powered by different fuels with particular reference to non compliant installations ofthefumes exhaust system oftheoutside air inlets SUITABILITY OF THE FUME
14. out perfectly in total compliance with Standards in force both national regional and municipal as well as these instructions For Italy installation must be carried out by professionally authorised staff Ministerial Decree dated 22 01 08 n 37 The manufacturer declines all responsibility for damages to objects and or persons caused by the system TYPE OF SYSTEM There are two different types of system Open vessel plant and closed vessel plant The product has been designed and realised to work with closed vessel systems ome CHECK THAT THE PRE FILLING PRESSURE OF THE EXPANSION VESSEL 15 1 5 BAR ENGLISH 5 Extraflame SAFETY DEVICES FOR CLOSED VESSEL SYSTEM According to the UNI 10412 2 2009 Standard in force in Italy the closed systems must have safety valve pump control thermostat acoustic alarm activation thermostat temperature indicator pressure indicator acoustic alarm regulation automatic circuit breaker switch automatic circuit breaker block switch block thermostat circulation system expansion system safety dissipation system incorporated with the generator with thermal safety valve self activated whenever the appliance does not have a temperature self adjustment system DISTANCES OF SAFETY DEVICES ACCORDING TO THE STANDARD The temperature safety sensors must be in place on the machine at a distance no greater than 30 cm from the flow connection Whenever the generators lack a device those missing c
15. system booklet where applicable The installer must ask to be issued with a receipt stating that the documentation has been provided and must keep it with a copy of the technical documentation relating to the installation Installation performed by several parties If the individual installation steps are carried out by different parties each must document the work carried out for the customer and the for the operator working on the next step INSPECTION AND MAINTENANCE Frequency of operations Maintenance of the heating system and of the appliance must be carried out on a regular basis according to the table below TYPE OF APPLIANCE INSTALLED lt 15kW 15 35 kw Pellet operated appliance 1 year 1 year Water operated appliances 1 r 1 r closed fireplaces thermo stoves thermo kitchens yea yea Boilers 1 year 1 year Fumes exhaust system 4 t of fuel used 4 t of fuel used For further details refer to the cleaning and maintenance chapter Inspection and maintenance report At the end of the inspection and or maintenance operations a report must be issued and released to the owner or person acting for him who must confirm its receipt in writing The report must indicate the situations encountered the action taken any components replaced or installed and any comments recommendations and requirements The report must be kept with the relative documentation In the inspection and maintenance rep
16. 43 2005 chimneys general requirements UNI EN 1457 2012 chimneys clay ceramic flue liners UNI TS 11278 2008 Metal chimneys flue liners flue ducts UNI 7129 point 4 3 3 Fire Brigade provisions local rules and regulations NATIONAL REGIONAL PROVINCIAL AND TOWN COUNCIL REGULATIONS One must also bear in mind all laws and national regional provincial and town council Standards present in the country in which the appliance has been installed TERMS AND DEFINITIONS Aeration Air renewal is required both for the disposal of the combustion products and to prevent mixtures with a hazardous content of non combusted gases Closed hearth appliance Appliance designed for operation with closed combustion chamber Forced draught appliance Appliance with ventilation in the fumes circuit and combustion with fumes flow at a positive pressure with respect to the environment Chimney Structure consisting in one or several walls containing one or several outflow airways The purpose of this predominantly vertical element is to expel the combustion products at a convenient height from the ground Smoke duct Component or components that connect the outlet of the heat generator to the chimney Chimney cap Device that placed on the chimney outlet allows the dispersion of the combustion products even in presence of adverse weather conditions Condensation Liquid products which form when the fumes temperature is lower or equ
17. 7 OExtraflame ELISIR IDRO HYDRAULIC CONNECTIONS 1 Remove the galvanised back 2 Remove the two steel sheets by cutting the joints 3 Re position the back SS 4 Remove the two caps the ceramic covering and the two sides 5 First remove the left cast iron cover and then the complete left front panel 6 First remove the 6 screws of the right cast iron cover and then the complete right front panel 7 Connect the system flow T2 to the machine and the safety valve pipe T1 Refer to the template for the correct position 8 Connect the system return T3 to the machine Refer to the template for the correct position of the fittings 9 The stove must be about 10 mm away from the wall N 10 Re position the complete right panel Fix the right cast iron cover using the 6 screws 12 Reposition the caps the cast iron cover and the ceramic covering 13 Re position the 2 sides 11 Re position the complete left panel 8 ENGLISH Extraflame INSTANT DOMESTIC H
18. 8 of its weight For this reason they do not require seasoning in order to arrive at a sufficiently adequate degree of heat yield The pellets used must comply with the characteristics described by the following standards ENPLUS UNI EN 14961 2 UNI EN ISO 17225 2 class A1 or A2 The manufacturer always recommended using pellets with a diameter of 6 mm with its products PELLET STORAGE In order to ensure problem free combustion pellets must be stored in a dry place Open the tank lid and load the pellets using a scoop THE USE OF EXPIRED PELLETS OR ANY OTHER MATERIAL WILL AFFECT THE FUNCTIONALITY OF YOUR GENERATOR AND MAY LEAD TO THE TERMINATION OF THE WARRANTY AND CESSATION OF ANY ACCOMPANYING RESPONSIBILITY ON THE PART OF THE MANUFACTURER CHECKS AND PRECAUTIONS FOR FIRST IGNITION IMPORTANT IN ORDER FOR THE GENERATOR TO WORK PROPERLY THE HYDRAULIC SYSTEM S PRESSURE MUST BE BETWEEN 0 6 AND 2 5 BAR If the pressure detected by the digital pressure switch is below 0 6 or above 2 5 bar it triggers a boiler alarm Bringing the water pressure within the standard values it is possible to reset the alarm by pressing the button bz for 3 seconds The alarm can be reset only if the fumes motor has stopped and 15 minutes have elapsed from the display of the alarm THE PELLET LOADING MOTOR DOES NOT WORK Due to the filling of the system it is normal that there is air inside the circuit During the 1st ignition
19. ADDITIONAL THERMOSTAT INSTALLATION Switch the appliance off using the master switch positioned on the rear of the stove Remove the plug from the socket Refer to the electrical layout to connect the two thermostat cables onto the relative clamps positioned don the rear of the machine one is red and the other black STBY clamp Every model can have a different position of the relative clamps in the rear of the machine The image is given as an example irs FOR STANDBY ACTIVATION REFER TO THE USER MENU CHAPTER The STRY and AUX O Follow the instructions clamps found at the 1 described below for back of the stove h excant for the the connection to the STBY and AUX clamps Idro Model can be 1 Remove the right noted in the diagram at the side P Follow the instructions 2 M described below for Pass the STBY and the connection to the H AUX wiring through STBY and AUX clamps J the indicated cable Remove the right 0 gland panel AUX Connection reserved for Extraflame conveyed waves accessories Contact the dealer for further details ENGLISH 25 Extraflame USER MENU SET THERMOSTAT The following menu allow
20. AND LOGIC IGNITION Once the points listed previously have been checked press key 1 for three seconds to ignite the stove 15 minutes are available for the ignition phase After ignition and having reached the control temperature the stove interrupts the ignition phase and passes to STARTING STARTING During the starting phase the stove stabilises combustion increasing it progressively to then start ventilation and pass on to WORK WORK During the work phase the stove reaches the set power see following item ADJUSTING POWER SETTING Set the functioning power from 1 to 5 settable using keys 2 3 Power 1 minimum level Power 5 maximum level SET 2 TEMPERATURE Set the boiler temperature between 65 and 80 C using buttons 4 to 65 CIRCULATOR PUMP OPERATION The pump activates water circulation when the temperature of the water inside the stove reaches approx 60 C As the pump always functions above 60 an always open heating area is recommended to make product functioning homogenous avoiding overheating blocks Normally this area is defined Safety zone ROOM TEMPERATURE in models where provided front ventilation can be activated deactivated and room temperature can be verified by means of the room probe standard See chapter enable fan in the following pages BURN POT CLEANING While working the stove has an internal counter which cleans the burn pot after a set amount of time This phase will
21. CEDURE Press the key 6 SET CLOCK will appear Press key 2 several times until USER is displayed Press key 6 SET THERMOSTAT will appear Press key 2 until PELLET is displayed Use key 4 to increase and 5 to decrease the load during the WORK phase Press key 6 to confirm and 1 to return to the previous menus back to the initial status 9999 V1 FAN This menu allows in models where provided adjusting the front fan speed percentage CONTROLS PROCEDURE Press the key 6 SET CLOCK will appear Press key 2 several times until USER is displayed CZ Press key 6 SET THERMOSTAT will appear beg Press key 2 until V1 is displayed P Use keys 4 to increase and 5 to decrease 1 Press key 6 to confirm and 1 to return to the menu back to the initial status STAND BY The Stby function is used if immediate stove switch off or modulation via additional external thermostat is desired CONTROLS PROCEDURE Press the key 6 SET CLOCK will appear Press key 2 several times until USER is displayed Press key 6 SET THERMOSTAT will appear Press key 2 until STAND BY is displayed Io Use keys 4 5 to enable disable Press key 6 to confirm and 1 to return to the menu back to the initial status ENGLISH 27 Extraflame KEYS LOCKED The menu allows to lock the display keys like mobile phone Press keys 1 and 5 simultaneously With the function activated KEY
22. E FREQUENTLY CLEANING AND MAINTENANCE BY THE USER Routine cleaning operations as specified in this use and maintenance manual must be performed with the utmost care according to the instructions procedures and frequency intervals described in this use and maintenance manual CLEANING THE SURFACES AND COVERING Never use abrasive or chemically aggressive detergents for cleaning The surface cleaning must take place when both the generator and the coating are completely cold For the maintenance of surfaces and metal parts simply use a damp cloth with water or mild soap and water Failure to observe the instructions may damage the surface of the generator and invalidate the warranty CLEANING THE CERAMIC GLASS Never use abrasive or chemically aggressive detergents for cleaning The cleaning of the ceramic glass is allowed only when the latter is completely cold To clean the ceramic glazing simply use a dry brush and some damp newspaper dabbed in the ash If the glazing is very dirty only use a specific ceramic glazing detergent Spray a modest amount onto a cloth and wipe the ceramic glazing Do not spray cleaner or any other liquid directly on the glass or on the gaskets Failure to observe the instructions may damage the surface of the ceramic glass and invalidate the warranty CLEANING THE TANK PELLETS When the tank empties completely unplug the power cord from the generator and remove residues dust chips etc from the tank
23. NCE BY THE USER NN NN e ERES 30 ROUTINE MAINTENANCE PERFORMED BY QUALIFIED TECHNICIANS 33 BEGOMMISSIONING END ORSEASON Roms SEMEN MR 33 DISPLAYS cocco ERR 35 ALARMS 36 ENGLISH 3 Extraflame WARNINGS This instructions manual is an integral part of the product make sure that it always accompanies the appliance even if transferred to another owner or user or if transferred to another place If it is damaged or lost reguest another copy from the area technician This product is intended for the use for which it has been expressly designed The manufacturer is exempt from any liability contractual and extracontractual for injury damage caused to persons animals and objects due to installation adjustment and maintenance errors and improper use Installation must be performed by qualified staff which assumes complete responsibility for the definitive installation and consequent good functioning of the product installed One must also bear in mind all laws and national regional provincial and town council Standards present in the country in which the appliance has been installed as well as the instructions contained in this manual The Manufacturer cannot be held responsible for the failure to comply with such precautions After removing the packaging ensure that the content is intact and complete Otherwise contactthe dealer where the appliance was p
24. OT WATER PRODUCTION KIT Warnings if the instant hot water production kit is to be used contact the company technical after sales service STOVE POSITIONING For correct product functioning it is recommended to position it in a way that it is perfectly level with the aid of a spirit level REARMING The figures below show the positions for rearming the tank 85 C and 20 100 C We recommend contacting a qualified technician in the event rearming occurs to verify its cause ISIDE IDRO ELISIR IDRO DUCHESSA IDRO MELINDA IDRO GIORDANA IDRO THERMO PRODUCTS FEATURES ou O 85 88 92 e 8 lt lt 6 lt Saul c 2 2 A lt aa a a 5 E zm un cc 8 Water content of the thermo product heat exchanger 1 13 13 18 5 15 18 5 Volume of expansion vessel integrated into thermo product I 6 6 8 8 Maximum content of water in the system for integrated expansion vessel 23 23 33 36 33 3 bar safety valve integrated into the thermo product YES MES YES YES YES Minimum and maximum pressure switch integrated into the thermo YES YES YES YES YES product Pump integrated into the thermo product YES YES MES YES YES Pump max head m 5 5 5 5 5 Content of water in the system in addition to that of the 6 thermo product that can be managed with the integrated expansion vessel An additional expansion vessel must b
25. S EXHAUST SYSTEM Installation must be preceded by a compatibility test between the appliance and the fumes exhaust system by verifying the existence of documentation relating to the system existence and content of the chimney plaque suitability of the internal section of the chimney absence of obstructions all along the chimney predominantly vertical height and development of the chimney existence and suitability of the chimney cap distance of the outside wall of the chimney and of the smoke duct from combustible materials chimney type and material absence of other chimney connections 9 9 9 99 9 ENGLISH 11 Extraflame INSTALLATION Installation in premises with fire hazards is forbidden Installation in residential premises exceptfor sealed operation appliances is also forbidden in which there are liquid fuel operated appliances with continuous or intermittent operation which draw the combustion air in the room in which they are installed or inwhich there are type B gas appliances intended for room heating with or without production of domestic hot water and in adjacent and adjoining premises or in which in any case the depression measured during installation between the internal and external environment is greater than 4 Pa Installations in bathrooms bedrooms and studio flats Installation in bathrooms bedrooms and studio flats is only allowed for sealed or closed hearth appliances with
26. S LOCKED will appear every time a key is pressed CONTROLS PROCEDURE Press the key 6 SET CLOCK will appear Press key 2 several times until USER is displayed Press key 6 SET THERMOSTAT will appear Press key 2 until KEYS LOCKED is displayed Use keys 4 5 to enable disable Press key 6 to confirm and 1 to return to the menu back to the initial status 9 999 RESET Allows to reset all values modifiable by the user to the default values The modified data are 20 75 CONTROLS PROCEDURE SETTEMPERATURE 35 C Press the key 6 SET CLOCK will appear SET POWER 5 Press key 2 several times until USER is displayed ENABLE CHRONO OFF Press key 6 START PRG1 OFF SET THERMOSTAT will appear STOP PRG1 OFF Press key 2 until RESET is displayed MONDAY PRG1 OFF Use keys 4 5 to select ON and press key 6 anii all chrono parameters OFF The word DONE will be displayed to confirm PELLET 00 STAND BY OFF AIR DISCHARGE This function allows venting any air in the stove Upon activating the function The indicator lights of the circulators will light up on the display the pumps will be powered for 15 minutes and 30 seconds and then will stop for 30 seconds cut the power to interrupt CONTROLS PROCEDURE Press keys 1 and 4 simultaneously You will be prompted to enter the password Enter code 77 using key 4 Confirm using key 6 CHRONO The
27. SER is displayed Press key 6 SET THERMOSTAT will appear Press key 2 until DISPLAY is displayed Use keys 4 5 to enable disable ventilation brightness Press key 6 to confirm and 1 to return to the menu back to the initial status 999999 PELLET FEED ADJUSTMENT The following menu allows the adjustment of pellet feed as a percentage If the stove has functioning problems owing to the quantity of pellets adjust pellet feeding directly from the control board The problems correlated to the amount of fuel can be divided into 2 categories 26 ENGLISH Extraflame NO FUEL the stove can never develop a suitable flame tending to remain very low even at high powers at minimum power the stove tends to almost switch off taking the stove into NO PELLETS alarm condition when the stove displays the NO PELLETS alarm there may be non burned pellets inside the burn pot EXCESS FUEL the stove develops a very high flame even at low power the panoramic glass is very dirty obscuring it almost totally the burn pot tends to become encrusted blocking the holes for air intake due to the excessive pellet feed as it is only burned partially The regulation to be performed is a percentage Therefore a modification of this parameter will lead to a proportional variation of all stove feeding speeds Feeding is from 30 to 20 Follow the procedure on the display to perform this adjustment CONTROLS PRO
28. TART UP PHASE 2 WORK PHASE The combustion chamber is dirty Check cleanliness of the fumes pipe of the sensor in the The flue exhaust pipe is blocked primary air channel and the combustion chamber NO The pellet feed box is empty Check for the presence of pellets in the feed box feed calibration inadequate Adjust pellet flow see Pellet feed adjustment IGNITION Check the procedures described in the Ignition chapter NO IGNITION Take the stove to OFF conditions using key 1 and repeat the No current during the ignition phase procedure described in the Ignition chapter BLACK OUT The pellet feed box is empty NO PELLETS No pellet feed The motor reducer does not feed pellets Check for the presence of pellets in the feed box Adjust pellet flow see Pellet feed adjustment The door is not closed correctly Check hermetic door closure DEPR ALARM The ash drawer is not closed correctly Check hermetic closure of the ash drawer The combustion chamber is dirty Check cleanliness of the fumes pipe and the combustion The flue exhaust pipe is blocked chamber DEBIMETER Faulty flow sensor FAULT ancien disconnected Contact after sales centre The water in the stove has exceeded 95 C H20 OVERTEMPERA Possible air in the system TURE Insufficient circulation Contact after sales centre No or inadequate safety zone Possible circulator anomaly The system pressure rea
29. al to the water dew point Ducting pipe Pipe made up of one or several predominantly vertical elements specifically suitable for collecting and expelling the fumes as well as to withstand the relative components and any condensate over time suitable to be installed in a chimney existing or new technical compartment even in new buildings Sealed installation Installation of an appliance with sealed operation so that all the air required for combustion is taken from outside Maintenance Set of procedures required to ensure and maintain safety and functionality over time and maintain the efficiency of the system within the prescribed parameters Chimney system Chimney installed using a combination of compatible components manufactured or specified by a sole manufacturer whose product liability covers the entire chimney Fumes exhaust system Flue gas exhaust system independent from the appliance made up of a smoke duct chimney or individual flue and chimney cap Radiation area Area immediately in front of the hearth in which the radiant heat caused by combustion is diffused Reflux area Area beyond the extrados of the roof in which overpressure or depressions occur which may affect the proper discharge of the combustion products 10 ENGLISH Extraflame FUNCTIONAL OPERATIONS DIAGRAM State of the art installation and proper system operation include a series of activities 1 Preliminary activities Verification
30. an be installed on the generator flow pipe within a distance no greater than 1 m from the machine COMMISSIONING CHECKS Before connecting the boiler a wash all system piping in order to remove any residues which might compromise the correct functioning of certain system components pumps valves etc b check to verify that the flue has adequate draft is not narrowed and that other appliances do not discharge into the flue This is to prevent unexpected power increases Only after this control can the flue fitting be mounted between the boiler and the flue A check of the connections with pre existing flues is recommended AUTOMATIC THERMOSTATIC MIXER VALVE MANDATORY It is required to create an adequate anti condensation circuit that ensures a return temperature for the appliance of at least 55 C The anti condensation valve for example is applied in solid fuel boilers as it prevents the return of cold water in the heat exchanger Routes 1 and 3 are always open and together with the pump installed on the return they guarantee water circulation inside the biomass boiler exchanger A high return temperature allows efficiency improvement reduces formation of smoke condensation and prolongs the life span of the generator Valves on the market have different calibrations The manufacturer advises use of model 55 c with 1 hydraulic connections Once the valve calibration temperature is reached route 2 is opened and the boiler wat
31. ates the presence of an alarm On indicates the presence of an alarm Off indicates the absence of alarms Flashing indicates the deactivation of the depression sensor Ole It indicates weekly programming functioning Indicator on Weekly programming active Indicator off Weekly programming not active Indicates the water temperature status Off the T read by the probe is over the set temperature set On the T read by the probe is below the set temperature set Indicates the contact of the external additional thermostat On closed contact the contact of the external additional thermostat is closed On open contact the contact of the external additional thermostat is open Flashing with closed contact the contact of the external additional thermostat is closed and the STBY function is activated Flashing with open contact the contact of the external additional thermostat is open and the STBY function is activated It indicates functioning of the fumes motor Off flue gas motor deactivated On flue gas motor active Flashing breakdown contact technical after sales service It indicates functioning of the tangential fan where present Off not working On working Flashing motor at minimum Ir It indicates functioning of the pellet feed motor Off pellet feed motor deactivated On pellet feed motor active 1 1 o It indicates pump functioning Off
32. be shown on the display it will bring the stove to a lower power level and will increase the flue gas motor for a programmed amount of time When the cleaning phase is finished the stove will continue work going back to the selected power level MODULATION and H OFF As the temperature nears the setpoint the boiler starts modulation automatically setting itself at minimum power If the temperature increases exceeding the setpoint it will automatically switch off indicating H OFF and will automatically switch on again once the temperature returns below the setpoint SWITCH OFF Press key 1 for three seconds When the Operation has been performed the appliance automatically enters the switch off phase blocking the supply of pellets The flue exhaust motor and the hot air ventilation motor will remain on until the temperature of the stove has dropped below the factory parameters RE IGNITION The stove can be automatically and manually switched on only when the cooling cycle conditions and the set timer are met 24 ENGLISH Extraflame ADDITIONAL THERMOSTAT N B Installation must be performed by an authorised technician It is possible to thermostat a room adjacent to the room where the stove is positioned just connect a thermostat following the procedure described in the next point it is recommended to position the optional mechanical thermostat at a height of 1 50m from the ground Stove functioning with the external thermo
33. chrono allows to program 4 time spans within a day to use every day ofthe week The switch on and switch off time can be set in every time span along with the days of use of the programmed time span and the desired 20 temperature 65 80 C Example RECOMMENDATIONS The ignition and switch off times must be within the arc of Switch on time 07 00 CORRECT one day from 0 to 24 and not over several days Switch off time 18 00 Before using the chrono function set the current day and time Therefore check that the points listed in the Set clock sub chapter have been followed so that the chrono function Switch on time 22 00 INCORRECT works Aside from programming it activate it as well Switch off time 05 00 28 ENGLISH Extraflame PROGRAMMING EXAMPLE Let s suppose that the weekly programmer function is to be used and 4 time periods are to be used in the following way 1st time period from 08 00 to 12 00 every day of the week excluding Saturday and Sunday 2nd time span from 15 00 to 22 00 only on Saturdays and Sundays both times with a 75 C water temperature setpoint The display will show the various programming steps SET Use buttons 4 5 to enter the time SONTROLZIERDSEDUBE SEGCK 12 00 which corresponds to the ETDEBRE Press the key 6 set clock WILL APPEAR emt me ofthe Tat ume period 12 00 To confirm and continue programming Press key 2 until SET CHRONO is displayed ENABLE CHRONO ENABLE Pr
34. d by the pressure MINIMUM PRESSURE COO NE Possible presence of air in the system Contact after sales centre ALARM Possible lack of water or leaks due to anomalies in some system component H20 PROBE ALARM H20 probe failure MAX H20 PRESSURE The pressure of the water has exceeded Ch ckithat the expansion vessels are not damaged under dimensioned ALARM the max threshold Check that the cold system is loaded at the correct pressure 36 ENGLISH Extraflame ENGLISH 37 Extraflame 38 ENGLISH Extraflame ENGLISH 39 uExtraflame Riscaldamento a Pellet Extraflame S p A Dell Artigianato 12 36030 PRECALCINO VI ITALY 20 39 0445 865911 amp 39 0445 865912 24 info extraflame it www lanordica extraflame com The Manufacturer reserves the right to vary the features and data shown in this booklet at any time and without prior notice in order to improve its products This manual cannot be considered as a contract for third parties 09 14 004275889 MU IDRO BASE 575 LCD 009
35. d sufficient when the room is equipped with air inlets according to the table Air inlet See figure 2 Percentage of the 5 net opening section with Minimum net opening value of ppp lignes ev dene respect to the appliance fumes the ventilation duct outlet section Pellet stoves UNL EN 14785 80 Boilers UNI EN 303 5 50 100 cm In any case ventilation is deemed sufficient when the pressure difference between the external and internal environment is equal to or less than 4 Pa Inthe presence of type B gas appliances with intermittent operation not intended for heating they must have their own aeration and or ventilation opening The air inlets must meet the following requirements they must be protected with grids metal mesh etc but without reducing the net useful section they must be made so as to make the maintenance operations possible positioned so that they cannot be obstructed The flow of clean uncontaminated air can also be obtained from a room adjacent to that of installation indirect aeration and ventilation as long as the flow takes place freely through permanent openings communicating with the outside The adjacent room cannot be used as a garage warehouse of combustible material or for any other activity with a fire hazard bathroom bedroom or common room of the building FUMES EXHAUST SYSTEM GENERAL REQUIREMENTS The heat generator works in a vacuum and has an outp
36. e installed for a higher content of water 4 Head m The following graph shows the behaviour of the circulator 1 pump used on our thermo products at the speeds that can be set 0 0 0 5 1 0 1 5 2 0 2 5 Flow rate m3 h ENGLISH 9 Extraflame DEVICES in the relevant models Door micro switch With the door open the operation of the burn pot cleaning system is blocked Electronic pressure switch in the event of inadeguate pression it sends the machine in alarm conditions F 2 5 A 250 V fuse stoves protects the machine from violent current surges 85 C calibrated mechanical bulb with manual rearm intervenes by blocking fuel feed if the pellet tank t reaches the limit of 85 C Rearm must be performed by qualified staff and or the manufacturer s technical after sales assistance Pellet tank temperature control probe if the tank over heats the machine automatically modulates to return to normal temperature values Mechanical air pressure switch blocks the pellet in the event of insufficient depression REFERENCE STANDARDS The installation must be in compliance with UNI 10683 2012 heat generators fed with wood and other solid fuels installation The chimneys must be in compliance with UNI EN 13063 1 and UNI EN 13063 2 UNI EN 1457 UNI EN 1806 in the event of non metallic chimneys EN 13384 1 13384 chimneys Thermal and fluid dynamic calculation methods UNI EN 14
37. er goes to the system via the flow 1 Valve sold as an accessory optional 6 ENGLISH Extraflame HYDRAULIC PLANT BASIC LAYOUT NOTE the drawing in the figure is an example KEY A Primary air inlet Flue exhaust outlet Circulator pump in the models where provided T1 3 bar safety drain T2 Boiler flow outlet T3 Boiler return inlet M Manometer Thermometer G Filling system Safety valve discharge VB Balance Valve SI System exhaust GIORDANA IDRO ISIDE IDRO MELINDA IDRO DUCHESSA IDRO c C_ 77 Pee o TU u 1198 ELISIR IDRO T2 _ 2 a B a 9 g 0 2 TL 13 22 BE m E 25 175 5 XL pus b d WE RECOMMEND REFERRING THE TEMPLATE MANUAL FOR FURTHER INFORMATION REGARDING HYDRAULIC CONNECTIONS AIR INTAKE FLUE EXHAUST AND DIMENSION SPECIFICATIONS OF THE PRODUCT IN QUESTION ENGLISH
38. ess key 6 ENABLE CHRONO and OFF CHRONO the days 2 and 3 to scroll through MONDAY PRG1 will appear ON the days the day of the week will be ON OFF Press key 4 to activate or deactivate the displayed followed by OFF CHRONO function Select ON select from Monday to Elisirt in ON excluding Saturday and Sunday OFF SET 2 TEMPERATURE 1ST TIME SPAN Press key 6 to confirm and continue Press key 6 to confirm and continue START PRG1 programming SET PRGA j OFF A programming Use keys 4 5 to select the desired H2O 75 C START PRG1 OFF will appear temperature 65 80 C Press key 6 to confirm and continue 1ST TIME PERIOD SWITCH ON reed econ tie pete Use keys 4 5 to enter the time 8 00 Ba must be programmed which corresponds to the switch on START PRG1 time of the 1st time period E START PRG2 i 08 00 The sequence to be followed is the OFF To confirm and continue programming press button 6 Press button 3 to go back to the previous parameter SET CHRONO 1ST TIME PERIOD SWITCH OFF press button 6 Press button 3 to go back to the previous parameter ENABLE 1ST TIME PERIOD DAYS Use keys 4 and 5 to enable disable same and is repeated as for the 1ST TIME PERIOD SWITCH ON 2ND TIME PERIOD SWITCH ON At this point the second time period must be programmed The sequence to be followed is the same and is
39. hefeed box must be full of pellets Do not touch the surfaces as they could still be combustion chamber must be clean unstable Theburn pot must be completely clear and clean Airthe room well several times o Check the hermetic closure of the fire door and the ash The hardening of the surfaces is terminated after drawer several heating processes Ensure that the power supply cable is connected correctly This appliance must not used to burn waste Thebipolarswitchintherearright part mustbe positioned on 1 POT DIVIDER IT IS PROHIBITED TO USE THE APPLIANCE WITHOUT DIVIDER 27 AND OR PLATE SEE FOLLOWING FIGURE ITS REMOVAL JEOPARDISES THE SAFETY OF THE PRODUCT AND C WILL IMMEDIATELY MAKE THE WARRANTY NULL AND VOID N IN THE EVENT OF WEAR OR DETERIORATION REQUEST THE i SPARE PART FROM THE AFTER SALES SERVICE REPLACEMENTS ARE NOT COVERED BY THE WARRANTY SINCE ITEMS ARE SUBJECT TO WEAR HEARTH PLATE ENGLISH 21 Extraflame THE REMOTE CONTROL The remote control allows adjusting all that can normally be done through the LCD display The table below shows the various functions in detail 1 ON OFF Pressing the key for three seconds the stove will switch on or off 2 POWER INCREASE Pressing the key will increase the Operating power 3 POWER DECREASE Pressing the key will decrease the Operating power 4 T INCREASE This button allows
40. in white The insulated double wall chimney systems are indicated in grey One can disregard the quota only in the event of using an appropriate heat protection screen for example wall plate to protect the intrados of the framework floor SMOKE DUCT General requirements The smoke ducts must be installed in compliance with the following general requirements be equipped with at least one sealed outlet for eventual fumes sampling they must be insulated if they cross through rooms that are not to be heated or outside the building they must not cross rooms in which the installation of combustion appliances is forbidden nor in other premises compartmentalised against fire or with a fire hazard nor in rooms and or areas that cannot be inspected they must be installed so as to allow normal thermal expansion they must be fitted to the opening of the chimney without protruding inwards the use of flexible metal pipes to connect the appliance to the chimney is not allowed NY ad ri 704 74 SR I D Chimney 2 4 L L ff fos y Correct 7 3 Sf g Gf 27 g s Y LI OK Lj OK 14 ENGLISH Extraflame counter slope sections are not allowed thesmoke ducts must have along their entire length a diameter that is no less than that
41. lated flue Insulated condensation proof T fitting with inspection plug IT IS NOT RECOMMENDED TO INSTALL A 90 BEND AS THE FIRST INITIAL PART SINCE THE ASH WOULD BLOCK THE PASSAGE OF THE FUMES IN A SHORT TIME CAUSING PROBLEMS TO THE GENERATOR DRAUGHT a Ash deposited in the 90 bend Ash deposited in the 90 bend ENGLISH 15 Extraflame EXAMPLES CORRECT CONNECTION TO THE CHIMNEY Protection from rain and wind Steel plate airtight T fitting with inspection plug Protection from rain and wind T 7 ax inspection plug Max 3 mt S Zil 1 a 3 50 Insulated fitting with T fitting with inspection plug DEED It is mandatory to use airtight pipes CHIMNEY In addition to the general requirements the chimneys for releasing combustion products into the atmosphere must operate under negative pressure operation under positive pressure is not allowed have a preferably circular internal section square or rectangular sections must have rounded corners with a radius of less than 20 mm hydra
42. of the attachment of the appliance exhaust pipe any section changes are allowed only on the inlet to the chimney they must be installed so as to limit the formation of condensation and prevent their release from the joints they must be positioned at a distance no less than that indicated in the product specifications from combustible materials the smoke channel duct must allow to collect the soot and to be cleaned using a swab and inspected after being disassembled or through inspection openings when not accessible from inside the appliance ADDITIONAL REQUIREMENTS FOR APPLIANCES FITTED WITH AN ELECTRIC FAN FOR FUMES EXPULSION For the heat generator appliances equipped with electric fan for expelling fumes the instructions below must be followed The horizontal sections must have a minimum upward slope of 396 Thelength of the horizontal section must be minimal and in any case no longer than 3 metres The number of direction changes including the one due to the use of the T element must not be more than 4 Installation with internal flue Insulated flue EXAMPLES OF CORRECT CONNECTION THE CHIMNEY Installation with internal external flue Protection from rain and wind Condensation proof T fitting with inspection plug TY Protection from rain and wind Insu
43. on all residue before it obstructs the passage of fumes DECOMMISSIONING END OF SEASON At the end of every season before you turn the stove off it is advisable to empty the pellet tank completely suctioning any pellet residue and dust from the inside In addition disconnect the generator from the electricity supply and for increased safety particularly if children are present remove the power supply cable Routine maintenance must be performed at least once a year gt IF THE POWER SUPPLY CABLE IS DAMAGED IT MUST BE REPLACED BY TECHNICAL SERVICE STAFF OR IN ANY CASE BY A SIMILARLY QUALIFIED TECHNICIAN SO AS TO AVOID ALL RISKS ENGLISH 33 OExtraflame ROUTINE MAINTENANCE The pictures are purely indicative Fumes motor disassembly and cleaning and fumes pipe and T new silicone in the provided points Inspections of gaskets ash drawer and door replace them and apply silicone where envisioned Combustion chamber and heat exchanger full cleaning including ignition plug pipe Feed box complete emptying and cleaning
44. ort one must mention anomalies detected that cannot be removed which pose a risk to the safety of the user or serious damage to building components that have been tampered with If anomalies as per above were detected the owner or person acting for him must be warned in writing in the maintenance report to refrain from using the system until the safety conditions have been fully restored The inspection and maintenance report must include the main information of the technician or company who performed the inspection and or maintenance operations with their contact details date of intervention and the signature of the operator 18 ENGLISH Extraflame PELLETS AND FEEDING Pellets are made by applying high pressure to sawdust or wood waste products not containing paint from sawmills carpentry and other activities related to processing and working with wood Given that it does not use any glue to hold it together this type of fuel is completely environmentally friendly In fact the compactness of the pellets over time is guaranteed by a natural substance found in the wood itself wood coal In addition to being an environmentally friendly fuel in that it pushes wood residues to the limits pellets also have technical advantages While wood has a calorific value of 4 4kWh kg with 15 humidity after around 18 months of seasoning the calorific value of pellets is 5 kWh kg Pellet density is 650kg m3 and the water content is equal to
45. owever do not modify the structure of the system upon which one is intervening or its intended use according to the requirements laid down by the technical standards in force and by the manufacturer s use and maintenance manual 4 ENGLISH Extraflame HYDRAULIC SYSTEM Certain concepts referring to the Italian UNI 10412 2 2009 Standard are described in this chapter As previously described when installing all national regional provincial and town council Standards in force provided by the country in which the appliance has been installed must be complied with TABLE OF DEVICES FOR CLOSED VESSEL SYSTEM PRESENT AND NOT PRESENT IN THE PRODUCT Safety valve Pump control thermostat managed by the water probe and board program IN LII Acoustic alarm activation thermostat Water temperature indicator display Pressure transducer with display Acoustic alarm Automatic circuit breater switch managed by board program Pressure transducer with minimum and maximum pressure switch alarm Water overheating automatic circuit breaker blocking thermostat Circulation system pump NWN NN NN Expansion system During installation of the stove it is MANDATORY to adjust the system with a manometer in order to display the water pressure INSTALLATION AND SAFETY DEVICES The installation relative system connections commissioning and inspection of correct functioning must be carried
46. remove or insert the battery following the symbols on the remote control and on the battery itself For Operation 1 CR2025 3V lithium buffer battery is required If the remote control is off because it has no batteries stove can be controlled from the The batteries used contain metals harmful control panel on top of it for the environment They must therefore C While replacing the battery pay attention to the be disposed of separately in appropriate polarity by observing the symbol on the inside containers compartment of the remote control 22 ENGLISH Extraflame COMMISSIONING SETTINGS Once the power cable at the back of the stove has been connected move the switch also located on the back to 1 The switch at the back of the stove powers the stove board The stove remains off and a first screen appears on the panel with the word OFF ADJUSTING TIME DAY MONTH AND YEAR Set clock allows to adjust the time and date SET CLOCK CONTROLS PROCEDURE DAY MON TUE WED SUN HOURS 0 23 Press button 6 and SET CLOCK will appear MINUTES 00 59 Confirm using key 6 DATE 1 31 Use keys 4 and 5 to assign the day Proceed pressing key 2 MONTH m Follow the same procedure 4 5 to set and 2 to proceed YEAR 00 99 to adjust the hours minutes date month and year Press key 1 several times to confirm and exit the Menu ADJUSTING LANGUAGE
47. repeated as for the 1ST TIME PERIOD SWITCH ON On this occasion it is only necessary to enter the time for example start at 15 00 and Stop at 22 00 and to activate the days Saturday and Sunday by setting them at ON WHEN THE WEEKLY PROGRAMMER IS ACTIVE A BOX OF THE RELATIVE ICON WILL APPEAR ON THE CONTROL BOARD ENGLISH 29 Extraflame CLEANING AND MAINTENANCE ALWAYS FOLLOW THE INSTRUCTIONS IN MAXIMUM SAFETY CONDITIONS Make sue the power cable is unplugged since the generator could be programmed to start That the generator is cold in its entirety The ashes are completely cold Ensure an effective exchange of air in the room during the cleaning of the product A poor cleaning is detrimental to the proper functioning and safety For correct operation the generator must undergo routine maintenance by a gualified technician at least once a year The routine checks and maintenance operations must always be performed by gualified trained technicians in accordance with the applicable regulations in force and with the instructions provided in this use and maintenance manual EVERY YEAR MAKE THE EXHAUST FUMES SMOKE DUCTS AND T FITTINGS INCLUDING CAPS AND INSPECTION DOORS BE CLEANED IF ANY CURVES AND ANY HORIZONTAL SECTIONS gt THE CLEANING OF THE GENERATOR FREOUENCY IS APPROXIMATE THEY DEPEND ON THE OUALITY OF THE PELLETS USED AND THE FREOUENCY OF USE IT CAN HAPPEN THAT THESE OPERATIONS SHOULD BE PERFORMED MOR
48. s in models where provided setting the room temperature for those products equipped with front air fan Once the set temperature is reached the fan will set itself to the minimum The possible settings are OFF 06 40 The room temperature will be displayed alternately with the water temperature CONTROLS PROCEDURE Press the key 6 SET CLOCK will appear Press key 2 several times until USER is displayed Press key 6 SET THERMOSTAT will appear Use keys 4 5 to select the room temperature Press key 6 to confirm and 1 to return to the menu back to the initial status 6 99 ENABLE FAN This menu allows in models where provided enabling or disabling tangential motor Operation CONTROLS PROCEDURE Press the key 6 SET CLOCK will appear Press key 2 several times until USER is displayed Press key 6 SET THERMOSTAT will appear SOO Press key 2 until ENABLE FAN is displayed 4 Use keys 4 5 to enable disable ventilation 1 Press key 6 to confirm and 1 to return to the menu back to the initial status 5 6 DISPLAY This menu allows to regulate the brightness of the display The possible settings are from OFF 10 to 31 By activating OFF the backlit display shall turn off after a set delay The backlight will turn on again upon pressing a button or when the machine enters in alarm mode CONTROLS PROCEDURE Press the key 6 SET CLOCK will appear 4 Press key 2 several times until U
49. stat connected in the STBY clamp can be different on the basis of the activation or deactivation of the STBY function The STBY clamp leaves the factory jumpered therefore it is always with closed contact on request ADDITIONAL THERMOSTAT FUNCTIONING WITH STBY ACTIVE When the STBY function is activated the o LED flashes When the contact or external thermostat is not satisfied open contact temperature reached the stove will switch off As soon as the contact or external thermostat passes to the not satisfied status closed contact temperature to reach it will re ignite Note stove functioning depends on the temperature of the water inside the same and relative factory restrictions set If stove is in HOFF mode water temperature reached any additional contact or thermostat request will be ignored ADDITIONAL THERMOSTAT OPERATION WITH DEACTIVATED STBY When the STBY function is deactivated the gt LED is fixed When the contact or external thermostat is not satisfied open contact temperature reached the stove will go to minimum As soon as the contact or external thermostat passes to the not satisfied status closed contact temperature to reach the stove will start to work again at the pre set power Note stove functioning depends on the temperature of the water inside the same and relative factory restrictions set If stove is in H OFF mode water temperature reached any additional contact or thermostat request will be ignored
50. t of pellet appliances the fumes exhaust systems must be airtight if double designation elements are used G and O with or without seal elastomer for connecting the appliance to the chimney one must comply with the minimum distance XX in millimeters indicated for designation G in the event of fire due to soot one must ensure the restoration of the initial conditions by replacing the gaskets and damaged items and cleaning those remaining in use Ignition tests Operation of the appliance must be verified with an ignition test i e for mechanical feed appliances one must complete the ignition test verify proper operation for at least the next 15 minutes and adjust the switch off For appliances installed in a hot water heating system closed fireplaces thermo stoves testing must also extend to the entire hydraulic circuit ENGLISH 17 Extraflame Coverings and finishings The coverings and finishings must only be applied after having verified the proper operation of the appliance according to the indicated modalities TECHNICAL INSTALLATION DOCUMENTATION When installation is complete the installer must provide the owner or person acting for him according to the legislation in force with the declaration of conformity supplied with 1 the use and maintenance manual of the appliance and of the system components such as for example the smoke ducts chimney etc 2 photocopy or photograph of the chimney plaque 3
51. t will automatically ignite HOFF Stove off due to water temperature over set As soon as the water temperature drops below the set parameters the stove will switch back on ANTI FREEZE The anti freeze function is in progress as the H20 t is below the factory set threshold the pump is active until the water reaches the pre set factory parameter 2 C ANTILOCK The pump anti locking function is in progress only if the stove has been in Off status for at least 96 hours the circulator is activated for the amount of time set by the manufacturer to prevent it from locking ENGLISH 35 Extraflame ALARMS DISPLAY EXPLANATION SOLUTION On indicates the presence of an alarm Flashing indicates the deactivation of the depression sensor The alarm can be reset by pressing key 1 for 3 seconds only if the fumes motor has stopped and if 15 minutes have passed from when the alarm was displayed Indicates the presence of an alarm ASPIRATION FAULT Fumes motor fault Contact after sales centre FUMES PROBE Fumes probe failure Contact after sales centre Verify pellet feed see Pellet feed regulation If the problem HOT FUMES High flue gas temperature cannot be solved contact an authorised technician CLEAN CHECK UP 1 2 The door is not closed correctly Check hermetic door closure The ash drawer is not closed correctly Check hermetic closure of the ash drawer 1 S
52. uExtraflame Riscaldamento a Pellet LCD THERMO PRODUCTS USER MANUAL DUCHESSA IDRO DUCHESSA IDRO STEEL ELISIR IDRO MELINDA IDRO MELINDA IDRO STEEL ISIDE IDRO GIORDANA IDRO ENGLISH INGLESE Extraflame We thank you for having chosen our company our product is a great heating solution developed from the most advanced technology with top quality machining and modern design aimed at making you enjoy the fantastic sensation that the heat of a flame gives in complete safety 2 ENGLISH Extraflame ENGLISH WARNINGS 81544532 E DE ER R SAFETY eere tenente ed ROUTINE MAINTENANCE sauscassssacesussbesccessaussussaSusssuessceesnsedeccacssessssscndessesusesuesessticunsesseseuuesssessssancssessues soscssuessssestasenevostevessssssuscseisecssestssonsadeisans 4 HYDRAULIC SYSTEM usssursosesossonesnssnnssnnennssnnennnsnnssnnsnnssnnnnnssnnennnsnnennsennssnnsnnsnnnsnsnnnnussnennnssnnennssnnssnnnnnssnnnsussnnnsnnsnnnsnnennnsnnssnssnnssnnnsnnsnnennssnnesnnennnne 5 INSTALLATION AND SAFETY DEVICES wsccsssssssasscscssscososssonssseacssconsieseesoisavssssncussctooseashusonsssbeecoiuastdbenisbsusoessooscobosasoaiesoraznsovsiasstbeouadbouedunsssetesadpbasnsvavensobuasbcieossionsaaieazgere 5 TYPEOFSYSTEM 5 SAFETY DEVICES FOR CLOSED VESSEL SYSTEM 6 DISTANCES OF SAFETY DEVICES
53. ulically equivalent sections may be used as long as the ratio between the longer side and the shorter side of the rectangle which circumscribes the section is in any case no greater than 1 5 bedesigned for fumes be designed for fumes expulsion bepredominantly vertical and have no narrowing along their entire length haveno more than two direction changes with a slope angle no greater than 45 be fitted with in the event of operating in damp conditions a device for reflux drainage condensation rainwater Ducted system ducted system can be installed with one or more ducts operating only with negative pressure with respect to the environment The flexible hose compliant with UNI EN 1856 2 with T400 G characteristics meets the requirements CHIMNEY CAPS The chimney caps must meet the following requirements they must have a useful outlet section no less than double of that of the chimney ducted system on which it is installed they must be adapted in order to prevent the penetration of rain and snow in the chimney ducted system they must be built so that in the event of winds coming from all directions and from any angle the expulsion of combustion products is in any case ensured they must be free from mechanical intake aids 16 ENGLISH Extraflame COMBUSTION PRODUCTS OUTLET OUOTA The outlet guota is determined by measuring the minimum height between the roof covering and the lower point of the f
54. umes expulsion section into the atmosphere this quota must be outside the reflux area and at an adequate distance from obstacles which hinder or make the expulsion of the combustion products difficult or from openings or accessible areas Reflux area The outlet quota must be outside the reflux area calculated according to the indications below Near the ridge one considers the lowest between the two Buffer area for outlet quota Clear area for outlet quota above the roof slope 4 gt 10 REFERENCE DESCRIPTION CLEAR AREA MM Distance measured at 90 from the roof surface 1300 a Height above the ridge of the roof 500 The outlet of a chimney ducted system must not be near obstacles that may create turbulence areas and or prevent proper expulsion of combustion products and maintenance operations to be carried out on the roof Verify the presence of other chimney caps or skylights and dormers FUMES EXHAUST SYSTEM PRODUCT REQUIREMENTS Temperature class In the event of a pellet appliance temperature classes below T200 are not allowed Soot fire resistance class The fumes exhaust system interlocked with appliances supplied by solid fuels require soot fire resistance and the specification must be indicated by the letter G followed by the distance from combustible materials in millimeters XX in compliance with UNI EN 1443 In the even
55. urchased All electric components that make up the product must be replaced with original spare parts exclusively by an authorised after sales centre thus guaranteeing correct functioning SAFETY The generator must not be used by persons including children with reduced physical sensory and mental capacities or who are unskilled persons unless they are supervised and trained regarding use of the appliance by a person responsible for their safety Children must be checked to ensure that they do not play with the appliance Do not touch the generator when you are barefoot or when parts of the body are wet or damp The safety and adjustment devices must not be modified without the authorisation or indications of the manufacturer Do not pull disconnect twist electric cables leaving the stove even if disconnected from the electric power supply mains It is advised to position the power supply cable so that it does not come into contact with hot parts of the appliance The power supply plug must be accessible after installation Do not close or reduce the dimensions of the airing vents in the place of installation The airing vents are essential for correct combustion Donotleave the packaging elements within reach of children or unassisted disabled persons Thehearth door must always be closed during normal functioning of the product When the appliance is functioning and hot to the touch especially all external surfaces attention m
56. ust be paid 9 Check for the presence of any obstructions before switching the appliance on following a prolonged period of inactivity The generator has been designed to function in any climatic condition even critical In particularly adverse conditions strong wind freezing safety systems may intervene that switch the generator off If this occurs contact the technical after sales service and always disable the safety systems In the event the flue catches fire use suitable systems for suffocating the flames or request help from the fire brigade This appliance must not be used to burn waste Do not use any flammable liquids for ignition During the filling phase do not put the bag of pellets to into contact with the product The majolicas are top quality artisan products and as such can have micro dots crackles and chromatic imperfections These features highlight their valuable nature Due to their different dilation coefficient they produce crackling which demonstrate their effective authenticity To clean the majolicas it is recommended to use a soft dry cloth If a detergent or liquid is used the latter could penetrate inside the crackles highlighting them 9 9 ROUTINE MAINTENANCE Based on Decree 22 January 2008 n 37 art 2 routine maintenance means interventions aimed at reducing degradation due to normal use as well as dealing with accidental events entailing the need of first interventions which h
57. ut fan for fume extraction Each appliance must be connected to a suitable fumes exhaust system and ensure adequate dispersion of the combustion products into the atmosphere The combustion products must discharged above the roof Direct discharge from the wall or towards closed spaces is forbidden even with clear skies In particular it is forbidden to use flexible and extendible metal pipes The chimney should only receive the exhaust of the smoke duct connected to the appliance collective flues or conveying exhausts from hoods above cooking appliances of any kind or exhausts from other generators into the chimney itself or smoke duct are not allowed The smoke duct and the chimney must be connected with a continuity solution in order to prevent the chimney from resting on the appliance It is forbidden to have other air supply channels and pipes for plant engineering transit inside the fumes exhaust systems especially if over sized The components of the fumes exhaust system must be chosen in relation to the type of appliance to be installed in compliance with in the event of metal chimneys TS 11278 with particular attention to what is stated in the specification in the event of non metallic chimneys UNI EN 13063 1 and UNI EN 13063 2 UNI EN 1457 UNIEN 1806 considering especially temperature class pressure class fumes seal at least equal to the seal required for the appliance moisture resistance resistance to condensation
Download Pdf Manuals
Related Search