K6 Camera User`s manual
Contents
1. Please shut down the device and then unplug the power cable before you begin daily maintenance work 111 Use the dry soft cloth to clean the device lf there is too much dust please use the water to dilute the mild detergent first and then use it to clean the device Finally use the dry cloth to clean the device Please put the dustproof cap to protect the CCD CMOS component when you do not use the camera 1V Applicable model This manual can be applied to following models 1 Megapixel 720P Vandal proof IR HDCVI Dome Camera HAC HDBW2120EP HAC HDBW2120EN 1 Megapixel 720P IR HDCVI Dome Camera HAC HDW2120SP HAC HDW2120SN HAC HDW2120MP HAC HDW2120MN 2 Megapixel 1080P Vandal proof IR HDCVI Dome Camera HAC HDBW2220EP HAC HDBW2220EN 2 Megapixel 1080P IR HDCVI Dome Camera HAC HDW2220SP HAC HDW2220SN HAC HDW2220MP HAC HDW2220MN 1 General Introduction 1 1 Overview This series megapixel HD camera conforms to the HDCVI standard It supports video signal high speed long distance transmission without any delay It can be controlled by the DVR conforming to the HDCVI 1 2 Features High performance CMOS image sensor megapixel definition Support HD video and control signal coaxial transmission Support 75 3 coaxial cable transmission without any loss 720P series transmission distance over 500m 1080P series transmission distance over 300m High speed long distance real time transmission Support HDCVI HD and anal2. RS232 Control Mode v PTZ LS ATM POS Address 1 ACCOUNT Baudrate 9600 7 AUTO MAINTAIN Data Bits IMP EXP StopBis Ud L DEFAULT Parity None UPGRADE Figure 4 1 On the preview interface right click mouse and then select PTZ you can see an interface shown as below See Figure 4 2 Figure 4 2 Click Iris to open menu or confirm current operation 10 Click up down button to view all the items on the left pane of the following list Click left right button to set the corresponding values on the right pane of the following list If there is gl click confirm button to go to the 2nd menu Repeat the previous steps to set detailed value Click Return button to go back to the previous menu interface 11 Appendix Toxic or Hazardous Materials or Elements Toxic or Hazardous Materials or Elements Component Geen gt fe fe oo Component Device Construction Material Packing Poe e a O Indicates that the concentration of the hazardous substance in all homogeneous materials in the parts is below the relevant threshold of the SJ T11363 2006 standard X Indicates that the concentration of the hazardous substance of at least one of all homogeneous materials in the parts is above the relevant threshold of the SJ T 11363 2006 standard During the environmental friendly use period EFUP period the toxic or hazardous substance or elements contained in products will not leak or mutate so that the u
3. HDCVI Dome Camera User s Manual Version 1 0 0 Table of Contents 1 G N TAINIIOUUCLION EE en a ir a sree sc or a l 1 1 ONGI ON oea E A teeta tad ident e l 1 2 ROUES nd Dane E KE T l 2 Framework and DIMENSIONS 44e nn aaa a aTa anian 2 2 1 HAC HDBW2120EP N and HAC HDBW2220EPIN sesser 2 2 2 HAC HDW2120SP N and HAC HDW2220SPIN cccccccceceeeseesessessssssstseeaes 2 2 3 HAC HDW2120MP N and HAC HDW2220MP N 3 3 SUVS LMU MUN OT Meter a cc a de rates chier Ode nine 5 3 1 HAC HDBW2120EP N and HAC HDBW2220EPIN sesser 5 3 2 HAC HDW2120SP N and HAC HDW2220SPIN cccccceceeesesseseeessssssssaeees 6 3 3 HAC HDW2120MP N and HAC HDW2220MP N 8 MONDE mana tomate Mende ce teNennane 10 4 1 HDCVI Series DVR Settings ss 10 Appendix Toxic or Hazardous Materials or Elements 12 Welcome Thank you for purchasing our HDCVI camera This user s manual is designed to be a reference tool for your system Please read the following safeguard and warnings carefully before you use this series product Please keep this user s manual well for future reference il Important Safeguards and Warnings 1 Electrical safety All installation and operation here should conform to your local electrical safety codes The power shall conform to the requirement in the SELV Safety Extra Low Voltage and the Limited power source is rated 12V DC 24V AC in the IEC60950 1 We assume no liability or responsibility fo
4. destal Finally you can install the decoration ring to complete the installation 3 3 HAC HDW2120MP N and HAC HDW2220MP N Step1 Device Installation Take the wrench from the accessories bag and use it to loosen the three set screws on the side of the camera body See Figure 3 5 C1 Wrench C2 SetScrew Figure 3 5 Step 2 Pedestal Installation Turn the pedestal of the device and then pull the cable through it Use four screws to secure the pedestal to the proper position See Figure 3 6 FAURE Al Cable A2 Pedestal A3 Screw Figure 3 6 Step 3 Adjust Monitor Angle Turn the pan base to the pedestal and secure firmly Adjust rotate base and the dome body to get the lens to the proper monitor angle See Figure 3 7 B1 Pedestal Hite ioe eee B2 Pan Base B3 Rotate Base B4 Dome Body Figure 3 7 Step 4 Fix Monitor Angle To prevent the dome from moving use wrench to secure the three set screws to secure the monitor angle position 4 Menu 4 1 HDCVI Series DVR Settings Note The following operation and interfaces for reference only Please refer to the HDCVI series DVR user s manual for detailed information After connected the camera to the HDCVI series DVR from Main Menu gt Setting gt System gt PTZ you need to set control mode as HDCVI and the protocol as DH SD1 Click Save button to save current setup See auc 4 1 SETTING GENERAL z DISPLAY Channel 1
5. he holes you just dug Step 2 Use inner hex wrench to remove the three enclosure fastening screws and then remove the dome enclosure Step 3 Adjust the pedestal position according to the cable exit mode ceiling side Pull the cable through the cable side exit at the installation surface and the pedestal Please skip this step if you want to use ceiling exit mode Line up the screw holes at the bottom of the pedestal to the expansion bolts in the installation surface Put three self tapping screws to expansion bolts and then secure firmly Now the pedestal is on the installation surface Step 4 Adjust the camera module angle to a proper position and then fix the screws to fasten Figure 3 2 Step 5 Use three enclosure fastening screws to secure the dome housing on the pedestal 3 2 HAC HDW2120SP N and HAC HDW2220SP N Step1 Please take the installation position map in the accessories bag and then paste it on the ceiling or the wall according to your monitor area requirements Draw and then dig three holes in the installation surface and then insert three expansion bolts in the holes Secure these three bolts firmly Step 2 Turn counter clockwise to remove the decoration ring Please dig a cable exit hole in the surface according to the installation position map if you want to draw out the cable from the top of the installation surface You need to draw out the cable from the cable channel side port of the pedestal if yo
6. og SD switch output 720P series support 720P 25 720P 30 720P 50 720P 60 1080P series support 1080P 25 1080P 30 720P 25 720P 30 720P 50 720P 60 Support high performance 3D noise reduction denoise excellent performance in low illumination Support ICR switch to realize surveillance both in the daytime and at night 3 6mm fixed lens 2 8mm 6mm 8mm optional Support OSD on screen display suitable for user self defined setup Support DC12V power supplying IP66 compliance Support intelligent IR function max IR distance 20m 2 Framework and Dimensions 2 1 HAC HDBW2120EP N and HAC HDBW2220EP N Please refer to the following figures for dimension information The unit is mm See Figure 2 1 to Figure 2 3 Figure 2 1 Dome Cover gt at Dome Enctosu af N VJ pan sa IN f z be 7 Figure 2 2 IR Light Power Input Port Dome Module te SD HD Switch Cable Dome Pedestal gt N DS 3 w je A i Video Output Port y 2 Figure 2 3 2 2 HAC HDW2120SP N and HAC HDW2220SP N Figure 2 4 Lens Der Tt Body Dome Decoration Ring Video Cg YY i Er tn gt et Power 4 De SD HD Switch Control Cable af Figure 2 5 2 3 HAC HDW2120MP N and HAC HDW2220MP N 4 4 30 Figure 2 6 Standard defintonhigh definition switch control cable Installation base Fe ES Pan base Rotate base _ Dome Body _ Fig
7. r all the fires or electrical shock caused by improper handling or installation 2 Transportation security Heavy stress violent vibration or water splash are not allowed during transportation storage and installation 3 Installation Do not apply power to the camera before completing installation Please install the proper power cut off device during the installation connection Always follow the instruction guide the manufacturer recommended lf this product is installed in the ceiling please make sure the installation position can sustain the min SON 4 Qualified engineers needed All the examination and repair work should be done by the qualified service engineers We are not liable for any problems caused by unauthorized modifications or attempted repair 5 Environment This series camera should be installed in a cool dry place away from direct sunlight or strong light inflammable explosive substances and etc This series camera shall work on the specified working temperature Please keep it away from the electromagnetic radiation object and environment Please keep the sound ventilation Do not allow the water and other liquid falling into the camera 6 Accessories Be sure to use all the accessories recommended by manufacturer Before installation please open the package and check all the components are included Contact your local retailer ASAP if something is broken in your package 7 Daily Maintenance
8. se of these Substances or elements will not result in any severe environmental pollution any bodily injury or damage to any assets The consumer is not authorized to process such kind of substances or elements please return to the corresponding local authorities to process according to your local government statutes Note e This manual is for reference only Slight difference may be found in the user interface e All the designs and software here are subject to change without prior written notice e All trademarks and registered trademarks mentioned are the properties of their respective owners e If there is any uncertainty or controversy please refer to the final explanation of us e Please visit our website or contact your local service engineer for more information 12
9. u want to draw out the cable from the side port of the cable channel Adjust the device installation pedestal to the proper position and then draw the cable through the cable exit Line up the three screw holes in the device pedestal to the three plastic expansion bolt holes in the installation position Put the three self tapping screws in the three plastic expansion bolts firmly Now the dome camera is secure in the installation surface See Figure 3 3 Ceiling or wall Expansion bolt Dome camera body ST3 self tapping screws Decoration ring Figure 3 3 Step 3 Adjust the lens to get the clear monitor video See Figure 3 4 Use crosshead screwdriver to loosen the screw and the turn the camera body to the proper position manually Fix the screw again Important Do not remove the screw Loosen a little bit will be OK Please secure after you completed the setup Adjustment screw Crosshead screwdriver Figure 3 4 Step 4 Line up the bulge of the decoration ring to the nick of the camera body and install along the tilt installation Push and then turn decoration ring clockwise The installation completed after you secure the decoration ring You need to use the proper tool to open up the side port of the U cable channel of the decoration ring if you want to draw out the cable from the side port of the cable channel when you are installing the device cable And then you can draw out the cable from the cable channel of the pe
10. ure 2 7 p output port When the standard definition high definition switch control cable is short circuit system outputs standard definition video Otherwise when the circuit is open system outputs the high definition video 3 Installation Important Before the installation please make sure the installation surface can sustain at least 3X weight of the bracket and the camera 3 1 HAC HDBW2120EP N and HAC HDBW2220EP N The dome camera usually uses the ceiling installation It can be installed on the ceiling or the wall For side exit cable installation please make sure the side exit cable direction is the same as shown in the installation position map Before you secure the screws on the pedestal please put the cable through the cable exit of the pedestal Before you complete the installation and debug do not remove the electrostatic film After you remove the film do not touch the enclosure in case there is any scratch nn cg L iiis Expansion Bolts 4 A gt a J x gt LA ar is ff j f Fi 4 1 y Enclosure Fastening Screw fy En 4 A Inner Hex Wrencl Figure 3 1 Step 1 Take the installation position map from the accessories bag and then put it on the surface of the ceiling or the wall according to the cable exit position Dig three holes according to the installation position map and then take three expansion bolts from the accessories bag and put them to t
Download Pdf Manuals
Related Search