Home
SPPL-TP-CS-MS-Specification,Installation and Operation
Contents
1. sewer discharge pipe Tighten the flexible coupling fasteners and the wall mounting bolts Connect the 40mm basin trap to the 40mm sewer discharge pipe Connect the flush valve to water supply test amp check for leaks Connect bubbler valve to water supply test amp check for leaks Tighten all fasteners Apply no pick sealant around base and wall Test Flush mechanism and check for leaks Fit and secure access panels Clean stainless steel surfaces Protect the installed product by wrapping in plastic until all other work is complete and the system Is ready to be put into operation Manual Flushing Device purchased with Combi Unit or separately Approved Models Schell Verona Concealed WC Flush Valve Art No 02 2370399 The Schell Verona range of valves are used to operate the toilet flush and the basin These valves are fitted with single operation cartridge technology The valves comply to Australian Standards and is approved to Watermark MP52 Spec 020 1997 License No W 588 The WC flush valve systems have been approved for direct connection to the portable water supply and offer 6 3 litre dual flush volume The WC flush valve has been designed to incorporate an air break system This system is designed to prevent back syphonage These options are suitable for connection directly to the domestic cold water system The flush valves are suitable for general commercial installations with a range of methods to provide the ne
2. 09 Page 1 of 5 STODDART Specification Installation and Operation MANUFACTURING Stainless Steel Toilet amp Basin Combination STAINLESS PLUMBING PRODUCTS Manual Flush CONTENTS RECOMMENDA TON orce Eea eE eE inet eres cee easiest Doth tobi EA ahaa van nue ana e aad 3 RS PON SID TE oirre pee A AT tur EO EEEE EE E E A A 3 eO PE a a A A AA 3 FEATURE r E steeped nse Ricca cients Rd aa Reet 3 REFERENCED AUSTRALIAN STANDARDS itacinasrannedevisanedsientad inasai Aia AANNAM 3 NST AEA ON OF PRODUC Torrerer ern EA E N 4 Reou errno a ai Eaa 4 Installation of Toilet Pan and Basin Combination Unit ssssssrnsrernsrnsrerrsrnrrrrnrrnrrsrnrrnrnrrsrnrrrnrrnrrsrnrrrrnrrernrrerenne 4 Manual Flushing Device purchased with Combi Unit or Separately sssssssssssrssrnsrnsrrerrerrnrrnrrnnrnrrnrrnrrerrerreerrerne 4 A E a a E aus tara cone ena E A E a a 5 Ceann A UCHO ennn e E a a raei rieri 5 Customer COMMPIGIAES sereine nnadenadanalanalanal es ad anni seal sa ETE EERE E EE r aeaaeai Ea ani naaar 5 Document reference SPPL TP CS MSSpecification Installation and Operation doc Revision Date 19 11 2009 Page 2 of 5 STODDART Specification Installation and Operation MANUFACTURING Stainless Steel Toilet amp Basin Combination STAINLESS PLUMBING PRODUCTS Manual Flush RECOMMENDATIONS Upon receiving a Stoddart product inspect immediately for any visible signs of shipping damage and notify the carrier immediately When removing the pr
3. 3 litre second at the valve with this being the minimum requirement Flow pressure at the valve 150 kpa Flow rate at the valve 1 4 litres second For a single valve installation a minimum supply pipe size to the valve of 25mm is required Multiple installations require larger pipe sizes and should be designed by an engineer Warranty Upon receiving a Stoddart product inspect immediately for any visible signs of shipping damage and notify the carrier immediately When removing the product from its packing be careful not to dent or scratch outer surface Any concealed damage should be noted and reported immediately to the freight carrier A claim should be filed with carrier promptly if appropriate Stoddart Manufacturing will not accept responsibility for shipping damage The Standard Terms and Conditions of Sale clearly details Standard Warranty Policy Plumbing Products offer additional conditions as follows e Warranty on materials and labour is limited to 12 months from date of installation e The Warranty does not cover damage caused by abuse misuse or improper application or improper installation e Warranty Claims must be submitted in writing to Stoddart Manufacturing within 14 days of observation of fault e Items may be returned to Stoddart s Factory by the Customer for warranty inspection For valid warranty claims Stoddart will repair or replacement the item and return it to the Customer promptly e For installed products Pho
4. STODDART Specification Installation and Operation MANUFACTURING ERE Stainless Steel Toilet amp Basin Combination STAINLESS PLUMBING PRODUCTS Manual Flush Specification Installation and Operation Manual For Stainless Steel Toilet Pans amp Basin Combination Units Square Bodied with Manual Single flush This manual is suitable for the following models Standard Models SPPL TP CS NT FA MS Toilet amp Basin Combi Square No Toilet Roll Holder Front Access Manual Single Flush SPPL TP CS T FA MS Toilet amp Basin Combi Square Toilet Roll Holder Front Access Manual Single Flush SPPL TP CS NT RA MS Toilet amp Basin Combi Square No Toilet Roll Holder Rear Access Manual Single Flush SPPL TP CS T RA MS Toilet amp Basin Combi Square Toilet Roll Holder Rear Access Manual Single Flush The Standard Model of the SPPL TP CS range is the SPPL TP CS NT FA ED Additional suffixes may be added for site specific variations e g For WA Police an additional block is added between bubbler and splashback This variation is recognised by a suffix WA Electronic Dual Flush units are configured standard with buttons mounted in Combi body By special request units can be supplied with only full flush button for single flush installations ES or with no buttons in body for remote button positions ER Document reference SPPL TP CS MSSpecification nstallation and Operation doc Revision Date 19 11 20
5. cessary recirculation through the building a A domestic water storage tank at the roof plant room level b Pressure system using pumps with cylinders fitted with diaphragm c Variable speed pumping systems d Pressure available from the authorities water mains Each building may use one or a combination of the above to recirculate domestic cold water to each of the building fixtures The flush valve is supplied complete with stopcock air brake flush pipe bend and cartridge The basin valve is supplied complete with integral stopcock The valves may be pre installed or loose as required The valve can be easily serviced since all serviceable parts are contained in the cartridge Document reference SPPL TP CS MSSpecification nstallation and Operation doc Revision Date 19 11 2009 Page 4 of 5 STODDART Specification Installation and Operation MANUFACTURING l TONE Stainless Steel Toilet amp Basin Combination STAINLESS PLUMBING PRODUCTS Manual Flush The cartridge is pre set to a 6 litre full flush but can also be simply reset to a 9 litre flush if required The valve is very compact and fully serviceable Operating range is from 22 metres head to 50 metres head flow pressure at the valve for standard models achieving noise levels under 20dB at 25 metres head Note A static pressure of 22 metres minimum head at the valve is required to ensure the valve opens when activated for flushing Design flow through Vr 1
6. eel Toilet amp Basin Combination STAINLESS PLUMBING PRODUCTS Manual Flush INSTALLATION OF PRODUCT Requirements All Stoddart Toilet amp Basin Units must be fitted with an electronically operated flush valve require the following e Water supply pipe for bubbler valve must be 15mm diameter minimum Water supply pipe to flush valve must be 20mm diameter minimum Flow to the flush valve face must be 1 2 1 5 litres sec Water pressure must be 250kpa minimum to 500kpa maximum An inline water filter should be fitted to protect the flush valves 240V 10A GPO for electronic models Installation of Toilet Pan and Basin Combination Unit All Stoddart Toilet pan and basin combination units are supplied with mounting holes pre punched for easy installation Remove the packing Remove the access panels from the Combi unit Locate the in the correct position amp set level Check the alignment of the toilet connection pipes Mark the mounting hole positions onto the floor and wall Remove the Combi Unit Flush the water lines before installing flush valves Install M10 fixing bolts in the wall and secure the Z clip to floor Fit the furnco flexible coupling to the sewer discharge pipe Fit the key seal to the inlet pipe The entire key seal Is to be inside the flush pipe when toilet is in position Fit a 40mm PVC trap to the Combi Unit basin outlet Position the toilet in the correct location whilst coupling the toilet waste to the
7. oduct from its packing be careful not to dent or scratch outer surface Any concealed damage should be noted and reported immediately to the freight carrier A claim should be filed with carrier if appropriate RESPONSIBILITIES Stoddart thoroughly inspect all products before they are despatched from our factory Stoddart Manufacturing will not accept responsibility for shipping damage The Plumber is responsible to ensure that the system is installed in accordance with all specific requirements of local codes and regulations including AS 3500 If questions or complications should arise during the installation of a Stoddart product that cannot be solved using the accompanying instructions please contact our offices or local representatives Note It is the responsibility of the plumber to install this product in accordance with AS3500 SCOPE This product is designed to be used in institutions and public facilities where vandalism resistance and or security is required The product is manufactured to the requirements of AS1172 1 and associated reference standards The product incorporates a toilet pan and basin in one combined unit The toilet pan and basin are pushbutton operated The product is manufactured as a P trap design with a rear water inlet P S converters are commercially available for applications requiring S trap sewer connection FEATURES Fully shrouded stainless steel pan Fully welded seamless outer construction Sec
8. tos must accompany the Warranty Claim for effective consideration e lf a site visit is required to conduct warranty repairs such work will be carried out during normal business hours e g 8am to 5pm Mon to Fri Cleaning I nstructions All surfaces of the product should be cleaned with mild soap and water or a neutral product Carefully rinse away all surplus cleaning product IMPORTANT Never use harsh or abrasive cleaners on stainless steel Do not use chlorinated or bleach water Customer Complaints All customer complaints regarding Stoddart Stainless Steel Toilets should be referred to Customer Service Department Stoddart Manufacturing 149 Jackson Road 4109 Sunnybank Brisbane Ph 61 7 33455011 Fax 61 7 33441000 Email sunnybank stoddart com au Web www stoddart com au Document reference SPPL TP CS MSSpecification nstallation and Operation doc Revision Date 19 11 2009 Page 5 of 5
9. ure access panels Flushing volume tested with specific electronic flushing devices to achieve 4 5 3 litre flush Integral hand basin Suicide resistant design REFERENCED AUSTRALIAN STANDARDS Markings Unit Marking to include Maker s Name Model AS 1172 1 1993 Section 1 6 identification Watermark Certification amp Flushing volume Installation amp Maintenance Manual to state valve manufacturers name model to be used in a matched performance set Copper alloy products marked DR components in contact with mains water Contamination of water Suitability of Plumbing amp Water Distribution Systems AS 3855 Products For Use In Contact With Drinking Water AS4020 Australian Standard for the pipe or fitting Joints i e Spigots sockets flanges Dimensional compliance with relevant or corresponding AS 3688 i other joint components where Australian Standard for the pipe or fitting interfacing other authorized Pipe Threads of Whitworth Form Part 2 Fastening Pipe components Threads Flushing Valve Shall comply with MP52 Spec 20 MP52 Spec 20 subjected to a hydrostatic pressure test of 2 0 1 0MPa for a period of 60 10 Os the flushing device amp bubbler aon Wa not leak an manufacture MP52 Spec 29 Document reference SPPL TP CS MSSpecification nstallation and Operation doc Revision Date 19 11 2009 Page 3 of 5 STODDART Specification Installation and Operation MANUFACTURING Stainless St
Download Pdf Manuals
Related Search
Related Contents
Montage- und BetrieBsanleitung KassettenModelle inverter Tests prismatiques de fixation fovéolaire (TPFF) J RR-RS150 - Panasonic Peerless Industries SUAC9000 User's Manual KOHLER K-14402-4A-BGD Installation Guide raccords a bague coupante CDA SC510SS Télécharger Copyright © All rights reserved.
Failed to retrieve file