Home
Multiple Vehicle Lines - With Keyless Remote Entry System
Contents
1. confirm that your personal code has been programmed to the keypad and the 9 0 button will flash twice to confirm that the keypad has exited programming mode Adhering the Keypad to the Vehicle All Vehicles NOTICE Do not adhere to moveable glass or windshield NOTE For proper adhesion the mounting surface should be at least 60 F 15 C NOTE The tape is very sticky and will adhere quickly once contact is made NOTE This product is designed to attach to your car door centered between the door handle and the window sill but will work mounted to a relatively flat surface Page 11 of 14 SKES7J 19G544 AA Copyright Ford 2015 FoMoCo Multiple Vehicle Lines With Keyless Remote Entry System 12 REMOVAL AND INSTALLATION Continued N0076546 45 Hold keypad up to desired mounting surface to confirm that all the tape will contact the mounting surface 46 Clean the vehicle surface where the keypad is to be adhered with the alcohol wipe provided 47 Pull the tape tabs off the keypad tape orient the keypad in the desired location and press onto the door surface e Be sure to press firmly on all edges to ensure proper adhesion of the tape Using the Keypad All Vehicles NOTE Refer to the Locks and Security section of your vehicle Owner s Guide for operation of remote transmitters during RUN START Remote transmitter operation in RUN START key position is model dependent 48 To unlock the drivers doo
2. synchronized e A progress bar will be displayed and will complete over 10 seconds while the vehicle is commanded to synchronize with the keypad e During the display of the 10 second progress bar activate the Lock command by pressing the 7 8 and 9 0 buttons on the keypad simultaneously Page 7 of 14 SKES7J 19G544 AA Copyright Ford 2015 FoMoCo Multiple Vehicle Lines With Keyless Remote Entry System 8 REMOVAL AND INSTALLATION Continued Test Keyless Entry Keypad Operation Type C Continued 36 When the synchronization is complete the programming routine will instruct the installer to turn off the vehicle ignition key and test operation of the keypad At this time perform the following steps 1 2 3 4 5 Close all vehicle doors Press the 7 8 and 9 0 buttons on the keypad to lock all doors Enter the keypad s Master Code to unlock the driver s door Within 5 seconds of Master Code entry press the 3 4 button to unlock all doors Within 5 seconds of pressing the 3 4 button press the 5 6 button multiple times to release the trunk Alternate Programming Method Type C Continued 37 If IDS responds with Serial Number is not Valid answer YES to the question Would you like to enter 48 character SK TIC RC string The 48 character string is located on the part package Using either the computer keyboard or the on screen buttons enter the 48 characters 4 digits at a time Select the tick bu
3. Multiple Vehicle Lines With Keyless Remote Entry System 1 REMOVAL AND INSTALLATION RF Keypad Removal RF Keypad 1 Please read ALL of these instructions before proceeding Removal and Reprogram Procedure NOTE This procedure should be used if the remote entry transmitters need to be reprogrammed to vehicle after the RF keypad has been installed to the exterior NOTE Step 3 is to be completed only if Step 2 is unsuccessful If Step 2 is successful no further action is required 2 Try to reprogram the RF keypad and other remote entry transmitters while the RF keypad is still attached to the exterior of the vehicle To program the RF keypad to your vehicle go to the appropriate Programming and Installation section reference the application table below 3 Remove the RF keypad from the vehicle exterior Clean area around RF keypad Slide cutting line behind RF keypad to cut tape Remove the RF keypad Remove adhesive from the vehicle using adhesion remover or strip off wheel Remove adhesive from the back of the RF keypad Scuff the back side of the keypad with a scuff pad or wire brush Clean the back of the keypad Add new tape if the RF keypad is to be re used o u A vn A LU N e To ensure proper keypad mounting avoid covering the protruding portion of the keypad back Use 3M Acrylic Plus Tape PT1100 Page 1 of 14 SKES7J 19G544 AA Copyright Ford 2015 FoMoCo Multiple Vehicle Lines With Keyless Rem
4. activity NOTE Ensure the brake pedal is not depressed during this procedure the electronic signal could interfere with programming 9 Make sure that you have all of the IKTs fobs and RF keypads for this vehicle O O OOO RF KEYPAD N0147499 Page 3 of 14 SKES7J 19G544 AA Copyright Ford 2015 FoMoCo Multiple Vehicle Lines With Keyless Remote Entry System 4 REMOVAL AND INSTALLATION Continued 10 Unlock the vehicle with programmed keyfob 11 Insert a key in the ignition 12 Turn the key from the OFF position to the RUN not START position four times within six seconds The fourth turn must end in the OFF position The system will chime to confirm the vehicle is in programming mode NOTE Some vehicles may require eight key cycles before returning to the OFF position 13 Within 10 seconds of completing the previous step press any button on remote entry transmitter if equipped The system will chime once to confirm that the Fob has been programmed 14 Within 10 seconds of completing the previous step press any button on remote entry transmitter if equipped The system will chime once to confirm that the Fob has been programmed 15 Within 10 seconds of completing the previous step press the 7 8 and 9 0 buttons simultaneously on the RF keypad 1 The system will chime once to confirm that the RF keypad has been programmed Repeat this step if more than one RF k
5. ecognized by the vehicle listed as In Use when activated delete the storage location contents Re enter the programming process and complete all steps through the synchronization process and the operational test Page 10 of 14 SKES7J 19G544 AA Copyright Ford 2015 FoMoCo Multiple Vehicle Lines With Keyless Remote Entry System 11 REMOVAL AND INSTALLATION Continued Programming a Personal Entry Code if desired All Vehicles NOTE If you lose your code card please contact your Ford or Lincoln dealership for factory code retrieval NOTE Do not set a personal code that uses five of the same number Do not set a personal code that uses five numbers in sequential order There is a maximum of two access codes the factory set code and one personal code If you reprogram the personal code the prior personal code will be erased NOTE Do not repeat the Programming and Installation section if a mistake is made in the Programming a Personal Entry Code section 41 Enter the factory set code as indicated on your code card 42 Within five seconds of entering the factory code press and hold the 1 2 button for 1 second the 9 0 button will flash twice to confirm the keypad is in programming mode Ca NO076542 43 Within five seconds enter your desired personal 5 digit code Each digit must be entered within five seconds of the previous digit 44 The vehicle doors will unlock lock unlock to
6. ed The doors will lock and then unlock to confirm that the fob has been programmed 24 Within 20 seconds of completing the previous step press any button on fob 2 if equipped The doors will lock and then unlock to confirm that the fob has been programmed 25 Within 20 seconds of completing the previous step press the 7 8 and 9 0 buttons simultaneously on the RF keypad 1 The doors will lock and then unlock to confirm that the RF keypad has been programmed Repeat this step if more than one RF keypad is used N0076545 Page 5 of 14 SKES7J 19G544 AA Copyright Ford 2015 FoMoCo Multiple Vehicle Lines With Keyless Remote Entry System 6 REMOVAL AND INSTALLATION Continued 26 27 28 After all remote entry transmitters have been programmed turn the ignition to the OFF position The doors will lock and then unlock to confirm that the vehicle has exited programming mode Test all remote entry transmitters for proper operation perform a lock unlock cycle on all remote entry transmitters If the remote entry transmitters do not program properly repeat the Type B Programming and Installation procedure The Driver s door my need to be opened and closed to reset the system Type C Programming and Installation 29 30 31 32 Refer to the Configuration Chart of this document to ensure the correct Communication Type is used on the keyless entry keypad Instructions for program
7. eypad is used Gor T NO076545 16 After all remote entry transmitters have been programmed turn the ignition to the RUN position for the vehicle to exit programming mode 17 Test all remote entry transmitters for proper operation perform a lock unlock cycle on all remote entry transmitters NOTE Most vehicles have an audible feedback when programming such as horn honks door locks unlocks or chimes Some vehicles may not have audible feedback e g C MAX 18 If the remote entry transmitters do not program properly repeat the Type A Programming and Installation procedure The driver s door may need to be opened and closed to reset the system Page 4 of 14 SKES7J 19G544 AA Copyright Ford 2015 FoMoCo Multiple Vehicle Lines With Keyless Remote Entry System 5 REMOVAL AND INSTALLATION Continued Type B Programming and Installation 19 Make sure that you have all of the fobs and RF keypads for this vehicle O O O OO RF KEYPAD N0147499 20 Unlock the vehicle with programmed keyfob 21 Put a key in the ignition 22 Turn the key from the OFF position to RUN not START position eight times within 10 seconds with the eighth turn ending in the RUN position The doors will lock and then unlock to confirm the vehicle is in programming mode NOTE 23 Within 20 seconds of completing the previous step press any button on fob 1 if equipp
8. ming to the correct communication type may be found under Configure Device Verify that the Integrated Diagnostic System IDS is updated to the most current version Connect IDS e Follow the prompts to select new vehicle session e Enter VIN Program the keyless entry keypad to the vehicle using the IDS e Select the Tool Box icon e Select Body e Select RF Keypad Learn Process Oscilloscope Tools gt Self Test DataLogger Module Programming Network Test E Chassis DRestraints Electrical P Service Functions Powertrain DBMS Reset LOWS Camera Alignment N0152099 Page 6 of 14 SKES7J 19G544 AA Copyright Ford 2015 FoMoCo Multiple Vehicle Lines With Keyless Remote Entry System 7 REMOVAL AND INSTALLATION Continued 33 Follow On screen instructions until the screen below is displayed N0152094 34 Enter the device s serial number and select the tick button e The serial number is up to six digits The serial number is located on the part package e IfIDS responds with Serial Number is not Valid go to the Alternate Programming Method section e If all four storage locations are in use go to the Free Storage Location section Synchronize Keyless Entry Keypad to Vehicle Type C Continued 35 Once the unique data is entered the programming routine will ask to select the tick button and activate the Lock command on the keypad This step will ensure that the keypad and the vehicle are
9. nti Scan Mode All Vehicles 54 If the wrong code has been entered 7 times 35 consecutive button presses the keypad is disabled for one minute and the keypad lights will flash during this time To Remove a Personal Code If Desired All Vehicles 55 Enter the factory code then within five seconds press and hold the 1 2 button for 5 seconds The vehicle will unlock lock and then unlock to confirm that your personal code has been removed The 9 0 key will flash four times 2 quick then 2 slow to confirm that your personal code has been removed amp fs 7 N0076542 56 Release the 1 2 button Owners Instructions All Vehicles 57 Place the user manual with the vehicle s owners manual when programming and installation is complete 58 This device complies with part 15 of the FCC rules and with RSS 210 of Industry Canada Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation e Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this equipment Page 14 of 14 SKES7J 19G544 AA Copyright Ford 2015 FoMoCo
10. ogrammed with information for a keypad 2 2 in use refers to the second keypad device that was activated during the device check 3 2 in use is listed next to the storage location where it is programmed If you want to delete keypad 2 from the vehicle select Location 2 and select the tick button If you want to keep keypad 2 programmed to the vehicle and delete all other locations select Location 1 Location 3 and Location 4 Then select the tick button Page 9 of 14 SKES7J 19G544 AA Copyright Ford 2015 FoMoCo Multiple Vehicle Lines With Keyless Remote Entry System 10 REMOVAL AND INSTALLATION Continued CB 1DS G8Sv1 2 0 00 Delete Stored Device Select the device location to erase Location 1 Location 2 2in use Location 3 Location 4 N0152097 Troubleshooting Type C Continued 40 Ifthe programming procedure has been completed and the vehicle does not respond to commands from the keyless entry keypad try these suggestions e Ensure that the vehicle is NOT a push button start vehicle e Ensure that the device is configured properly by following the steps in the Configure Device section e Ensure that the device is synchronized to the vehicle Enter the programming process Program Device to Vehicle section Instead of entering the device s serial number select the Delete button to determine whether the vehicle recognizes the keypad If the device is r
11. ote Entry System 2 REMOVAL AND INSTALLATION Continued 4 Reprogram the RF keypad from the driver seat area To program the RF keypad refer to the table below for appropriate reprogramming procedure CONFIGURATION CHART Model Year Communication Type Installation Method a 2016 Explorer 2 Intelligent Access Not Supported Vehicles Configure Device Not a Not Supported NOTE Reference the table above for communication type that applies for the vehicle NOTE The keyless entry keypad can be used in various vehicle applications The following procedure describes the method to switch between the two communication types 5 Upon pressing the 1 2 3 4 and 9 0 buttons simultaneously for at least one second all five buttons will flash at a two flashes per second rate This indicates the keypad is waiting for master code entry The master code is entered as in a normal keypad unlock each button press will give another five second window for the next button press If no button is pressed within five seconds the configure mode will exit 6 When the proper master code is entered the 9 0 button will flash a pattern that corresponds to the current protocol set e One flash per second for Communication Type 2 e Three flashes per second for Communication Type 1 Default 7 You will have 10 seconds to e Press the 9 0 button to change the protocol to Communication Type 2 e Press the 1 2 button to change the
12. protocol to Communication Type 1 Default Page20f14 lt i i SCSKESTRIGSSA AA Copyright Ford 2015 FoMoCo Multiple Vehicle Lines With Keyless Remote Entry System 3 REMOVAL AND INSTALLATION Continued NOTE Only one button press is recognized After the button press is registered the flash rate will change to reflect the new setting of the protocol If you first press the 1 2 button you cannot then press the 9 0 button to change the selection You must exit the session 8 Press the 5 6 button to confirm the entry the 1 2 3 4 5 6 and 7 8 buttons will flash four times to confirm protocol change and the keypad will turn off and sleep If the 5 6 button is not pressed within 10 seconds of protocol change the protocol will NOT change and the procedure will need to be repeated Type A Programming and Installation NOTE It is easier to program the keypad prior to attaching it to the vehicle NOTE After five seconds of idle time the keypad will reset itself NOTE You must have all remote entry transmitters available before beginning this procedure IKTs Fobs and RF keypads Check owners guide Locks and Security for maximum remote entry transmitters allowed and proper key positions If all remote entry transmitters are not present during the programming procedure the missing transmitters will not work following programming NOTE The vehicle will exit programming mode after 20 seconds of in
13. r enter your personal 5 digit code or the factory set code e Fach digit must be pressed within five seconds of each other 49 To unlock all doors press 3 4 button within five seconds of entering a valid keypad code nonn N0076543 Page 12 of 14 SKES7J 19G544 AA Copyright Ford 2015 FoMoCo Multiple Vehicle Lines With Keyless Remote Entry System 13 REMOVAL AND INSTALLATION Continued 50 To unlock the trunk or hatch if equipped press the 5 6 button within five seconds of entering a valid keypad code IKT vehicles may require the 5 6 button to be pressed twice Press the 5 6 button twice to open or close the passenger side power sliding door if equipped DIDE Bt N0076544 51 To unlock and open the driver side power sliding door if equipped press the 7 8 button twice within five seconds of entering a valid code Gari N0076554 52 To lock all doors press the 7 8 and the 9 0 keys simultaneously e You do not have to enter a 5 digit code Gor NO076545 Low Power Warning All Vehicles 53 If you unlock the door with the keypad and the locks cycle one additional time it is time to replace the unit e The battery is not replaceable Page 13 of 14 SKES7J 19G544 AA Copyright Ford 2015 FoMoCo Multiple Vehicle Lines With Keyless Remote Entry System 14 REMOVAL AND INSTALLATION Continued A
14. tton when all 48 characters have been entered Enter 48 character SK TIC RC string N0152095 Page 8 of 14 SKES7J 19G544 AA Copyright Ford 2015 FoMoCo Multiple Vehicle Lines With Keyless Remote Entry System 9 REMOVAL AND INSTALLATION Continued Free Storage Location Type C Continued 38 Ifall four storage locations are in use IDS will ask if you would like to determine which keypad units are programmed to which storage locations The process will begin by asking you to activate device 1 e Press the 7 8 and 9 0 buttons on the first keypad that is already programmed to the vehicle Then select the tick button on IDS e IDS will ask if you would like to check another device If there is another keypad on the vehicle select YES on IDS to check that keypad unit Proceed with the activation process to see if it is programmed to the vehicle e Repeat this process for all keypads attached to the vehicle Up to four keypads can be programmed to the vehicle OB 10S Gssv1 2 0 00 Delete Stored Device Please Activate Device 1 Note To Activate device press 7 8 and 9 0 buttons or enter the master code on the RF Keypad N0152096 39 When all keypads have been tested select NO when asked by IDS whether you would like to test another device A screen similar to the one below will be displayed 1 Location 1 4 refers to the four storage locations on the vehicle that may be pr
Download Pdf Manuals
Related Search
Related Contents
バージョンアップマニュアル GXT2-6000RTL630™ de Liebert Manual Fritadeira Elétrica Télécharger la fiche technique complète en PDF Samsung T9000 FDR із системою потрійного охолодження Triple Cooling, 819 л Керівництво користувача Smart Door Lock Macchine Edili - Imer International Spa Règlement sportif FFE Dataflex ViewMaster M5 Monitorarm 013 Copyright © All rights reserved.
Failed to retrieve file