Vizi Beam Hybrid 2R
Contents
1. Rev 12 13 User Instructions 2013 ADJ Products LLC all rights reserved Information specifications diagrams images and instructions herein are subject to change without notice ADJ Products LLC logo and identifying product names and numbers herein are trademarks of ADJ Products LLC Copyright protection claimed includes all forms and matters of copyrightable materials and information now allowed by statutory or judicial law or hereinafter granted Product names used in this document may be trademarks or registered trademarks of their respective companies and are hereby acknowledged All non ADJ Products LLC brands and product names are trademarks or registered trademarks of their respective companies ADJ Products LLC and all affiliated companies hereby dis claim any and all liabilities for property equipment building and electrical damages injuries to any persons and direct or indirect economic loss associated with the use or reliance of any information contained within this document and or as a result of the improper unsafe unsufficient and negligent as sembly installation rigging and operation of this product Europe Energy Saving Notice Energy Saving Matters EuP 2009 125 EC Saving electric energy is a key to help protecting the enviroment Please turn off all electrical products when they are not in use To avoid power consumption in idle mode disconnect all electrical equipment from power when not in use2. Personality is highlighted then press ENTER 2 Press the UP or DOWN buttons until Status Setting is dis played press ENTER 3 Press UP or DOWN buttons until Address via DMX is dis played and press ENTER 4 Either Off or On will be displayed use the UP and DOWN but tons to toggle between System Menu 5 Press ENTER to confirm your selection or press MODE ESC to exit To use this function follow these instructions To adjust the address of your unit you must first go to the address that it is currently set to From there you can adjust the address First make sure all channels are set to the value of 0 1 On your DMX controller set the DMX value of Channel 1 to the value 7 2 Now set the DMX value of Channel 2 to the value 7 to adjust the starting address between 1 and 255 To adjust the address between 256 and 511 set Channel 2 to the value 8 3 Set the DMX value of Channel 3 to your desired starting address This will take about 20 seconds before the unit accepts the new DMX address EXAMPLE lf you want the address to be 57 you must first set the address that is currently assingned to the unit Then set Channel 1 s value to 7 Channel 2 s value to 7 and Channel 3 s value to 57 Wait 20 seconds and the address should change on the unit to 57 2ND EXAMPLE If you want the address to be 420 you must first set the address that i
3. Remove the three small screws labeled A B amp C on the rear of the moving head 3 After removing the screws gently remove the panel 4 Carefully disconnect the two wires connected to the lamp Pic A 5 Next located on the left side squeeze the lamp holding clips togther and lift the holder Pic B 6 Replace the lamp with an exact match Reassemble in reverse order PicA Pic B Fuse Replacement Locate and remove the unit s power cord Once the cord has been removed located the fuse holder located inside the power socket Insert a flat head screw driver into the power socket and gently pry out the fuse holder Remove the bad fuse and replace with a new one The fuse holder has a built in socket for a spare fuse be sure not to confuse the spare fuse with active fuse ADJ Products LLC www adj com Vizi Beam Hybrid 2R Instruction Manual Page 54 Vizi Beam Hybrid 2R Cleaning Fixture Cleaning Due to fog residue smoke and dust cleaning the internal and external optical lenses and mirror should be carried out periodically to optimize light output Cleaning frequency depends on the environment in which the fixture operates l e smoke fog residue dust dew In heavy club use we recommend cleaning on a monthly basis Periodic cleaning will ensure longevity and crisp out put 1 Use normal glass cleaner and a soft cloth to wipe down the out side casing 2 Use a brush to wipe down the cooling vents and fan grill
4. amp LEFT buttons To confirm every selection press the ENTER button You can exit every menu and submenu by pressing the MODE ESC button The unit will automatically exit the menus if no buttons are pressed after 10 seconds These next pages will explain each func tion in the menu layout located on the previous page FUNCTION Set DMX Address With this function you can adjust the desired DMX address via the Control Board 1 Access the main menu and press the UP or DOWN buttons so that Function is higlighted then press ENTER 2 Press the UP or DOWN buttons until Set DMX Address is displayed and press ENTER The current DMX address will now be displayed 3 Use the UP or DOWN buttons to adjust the DMX address 4 Press ENTER to confirm or press MODE ESC to return to the main menu DMX Value This function will allow you to see the DMX value of each DMX channel that is currently being used at the time 1 Access the main menu and press the UP or DOWN buttons so that Function is highlighted then press ENTER 2 Press the UP or DOWN buttons until DMX Value is displayed and press ENTER 3 A DMX Channel will be displayed Example Prism Color Wheel Gobo Wheel etc Press ENTER when you find the DMX channel that you would like to check When you press ENTER the DMX value of that channel will displayed 4 Press the MODE ESC button to exit Slave Mode This function lets you designate the
5. exit Reset Others With this function you can reset all other motors 1 Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that Reset Function is highlighted then press ENTER 2 Press the UP or DOWN buttons until Reset Others is displayed press ENTER 3 Press ENTER to confirm your selection or press MODE ESC to exit EFFECT ADJUST Test Channel With this function you can test correct each channel function 1 Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that Effect Adjust is highlighted then press ENTER 2 Press the UP or DOWN buttons until Test Channel is displayed press ENTER 3 Use the UP or DOWN buttons to scroll through the various chan nels 4 Press ENTER or press MODE ESC to exit Manual Control With this function you can easily adjust the lamp All effects will be canceled the shutter will open and output intensity ADJ Products LLC www adj com Vizi Beam Hybrid 2R Instruction Manual Page 35 Vizi Beam Hybrid 2R System Menu will be 100 With the individual functions you can focus the light on flat surface a wall and finely adjust the lamp 1 Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that Effect Adjust is highlighted then press ENTER 2 Press the UP or DOWN buttons until Manual Control is dis played press ENTER 3 Use the UP or DOWN b
6. Duty Cycle None DMX 3 DMX Channel Modes 10 Channels 12 Channels or 16 Channels Sound Active Yes Working Position Any Safe Secure Position Warranty 1 Year 365 days Auto Sensing Voltage This fixture contains a electronic bal last which will auto sense the voltage when it is plugged into the power source Please Note Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice ADJ Products LLC www adj com Vizi Beam Hybrid 2R Instruction Manual Page 58 ADJ Products LLC 6122 S Eastern Ave Los Angeles CA 90040 USA Tel 323 582 2650 Fax 323 725 6100 Web www adj com E mail info americandj com A D J Supply Europe B V Junostraat 2 6468 EW Kerkrade Follow Us On FE Netherlands ci service adjgroup eu www adj eu Youruberomm llshing Tel 31 45 546 85 00 Fax 31 45 546 85 99
7. LLC www adj com Vizi Beam Hybrid 2R Instruction Manual Page 14 Vizi Beam Hybrid 2R Set Up 5 Pin XLR DMX Connectors Some manufactures use 5 pin DMX 512 data cables for DATA transmission in place of 3 pin 5 pin DMX fixtures may be implemented in a 3 pin DMX line When inserting stan dard 5 pin data cables in to a 3 pin line a cable adaptor must be used these adaptors are readily available at most electric stores The chart below details a proper cable conversion 3 Pin XLR to 5 Pin XLR Conversion Conductor 3 Pin XLR Female Out 5 Pin XLR Male In Data True signal Pin 3 Pin 3 Not Used Not Used Po Pin 4 Do Not Use Pin 5 Do Not Use ADJ Products LLC www adj com Vizi Beam Hybrid 2R Instruction Manual Page 15 Vizi Beam Hybrid 2R System Menu Low Fan Speed High Fan Speed Set Dmx Address A001 AXXX DMX address setting 5 Dmx Value PAN DMX value display 3 Slave Mode Slavel Slave2 Slave3 Slave setting Auto Program Master Alone Auto program Sound Control Master Alone Sound Control Time Information Current Time XXXX Hours Power on running time Total Run Time XXXX Hours Fixture running time Last Run Time XXXX Hours Fixture Last times clear Lamp Hours XXXX Hours Lamp running time 3 Lamp Off Time XXXX Minute Lamp off time LastRun Password Password XXX Timer Password 038 2 Clean Last Run ON GEE Clear Fixture Last time LampTime Password Passw
8. or DOWN buttons until Fans Control is displayed press ENTER 3 Either Auto Fan Speed default Low Fan Speed or High Fand Speed will be displayed use the UP and DOWN buttons to toggle between 4 Press ENTER to confirm your selection or press MODE ESC to exit Display Setting Shutoff Time With this function you can have the LCD display after 2 59 minutes Use this function to adjust the time 1 Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that Personality is highlighted then press ENTER 2 Press the UP or DOWN buttons until Display Setting is dis played press ENTER 3 Press UP or DOWN buttons until Display Shutoff Time is dis played and press ENTER 4 05m 5 minutes will be displayed use the UP and DOWN but ADJ Products LLC www adj com Vizi Beam Hybrid 2R Instruction Manual Page 31 Vizi Beam Hybrid 2R tons to adjust the shutoff time between 02m 60m or Off 5 Press ENTER to confirm your selection or press MODE ESC to exit System Menu Reverse With this function you can rotate flip the display 180 degrees 1 Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that Personality is highlighted then press ENTER 2 Press the UP or DOWN buttons until Display Setting is dis played press ENTER 3 Press UP or DOWN buttons until Display Reverse is disp
9. possessions and territories It is the owner s responsibility to establish the date and place of purchase by acceptable evidence at the time service is sought For warranty service you must obtain a Return Authorization number RA before sending back the product please contact ADJ Products LLC Service Department at 800 322 6337 Send the product only to the ADJ Products LLC factory All shipping charges must be pre paid If the requested repairs or service including parts replacement are within the terms of this warranty ADJ Products LLC will pay return shipping charges only to a designated point within the United States If the entire instrument is sent it must be shipped in it s original package No accessories should be shipped with the product If any accessories are shipped with the product ADJ Products LLC shall have no liability whatsoever for loss of or damage to any such accessories nor for the safe return thereof This warranty is void if the serial number has been altered or removed if the product is modified in any manner which ADJ Products LLC concludes after inspection affects the reliability of the product if the product has been repaired or serviced by anyone other than the ADJ Products LLC factory unless prior written authorization was issued to purchaser by ADJ Products LLC if the product is damaged because not properly maintained as set forth in the instruction manual This is not a service contract and this
10. the UP or DOWN buttons so that Reset Function is highlighted then press ENTER 2 Press the UP or DOWN buttons until Reset Pan Tilt is dis played press ENTER 3 Press ENTER to confirm your selection or press MODE ESC to exit Reset Colors With this function you can reset the color wheel 1 Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that Reset Function is highlighted then press ENTER 2 Press the UP or DOWN buttons until Reset Colors is displayed press ENTER 3 Press ENTER to confirm your selection or press MODE ESC to exit Reset Gobos With this function you can reset the gobo wheel 1 Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that Reset Function is highlighted then press ENTER 2 Press the UP or DOWN buttons until Reset Gobos is displayed press ENTER 3 Press ENTER to confirm your selection or press MODE ESC to ADJ Products LLC www adj com Vizi Beam Hybrid 2R Instruction Manual Page 34 Vizi Beam Hybrid 2R System Menu exit Reset Shutter With this function you can reset the shutter motor 1 Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that Reset Function is highlighted then press ENTER 2 Press the UP or DOWN buttons until Reset Shutter is displayed press ENTER 3 Press ENTER to confirm your selection or press MODE ESC to
11. the display in the form of XXer XX will represent a function number For example when the display shows 03Er it means there is some type of error with the channel 3 motor If there are multiple errors during the start up process they will all flash in the display For exam ple if the fixtures has errors on channel 1 and channel 3 all at the same time you will see the error message flash 01Er and OSEr repeated 5 times If an error does occur during the initial start up procedure the fixture will self generate a second reset signal and try to realign all the motors and correct the errors if the errors persist after a second attempt a third attempt will be made If after a third attempt all the errors have not been corrected the fixture will make the following determinations 1 3 or more errors The fixture cannot function properly with three or more errors therefore the fixture will place itself in a stand by mode until subsequent repairs can be made 2 Less than 3 errors If the fixture has less than 3 errors there fore most other functions will work properly The fixture will attempt to operate normally until the errors can be corrected by a technician The errors in question will remain flashing in the display as a reminder of internal errors 01Er PAN movement error This message will appear after a fixture reset if the pan yoke s magnetic indexing circuit malfunctions sensor failed or magnet
12. warranty does not include maintnance cleaning or periodic check up During the period specified above ADJ Products LLC will replace defective parts at its expense with new or refurbished parts and will absorb all expenses for warranty service and repair labor by reason of defects in material or workmanship The sole responsibility of ADJ Products LLC under this warranty shall be limited to the repair of the product or replacement thereof including parts at the sole discretion of ADJ Products LLC All products covered by this warranty were manufactured after August 15 2012 and bear indentifying marks to that effect ADJ Products LLC reserves the right to make changes in design and or improvements upon its products without any obligation to include these changes in any products theretofore manufactured No warranty whether expressed or implied is given or made with respect to any accessory supplied with products described above Except to the extent prohibited by applicable law all implied warranties made by ADJ Products LLC in connection with this product including warranties of merchantability or fitness are limited in duration to the warranty period set forth above And no warranties whether expressed or implied including warranties of merchantability or fitness shall apply to this product after said period has expired The consumer s and or Dealer s sole remedy shall be such repair or replacement as is expressly provided above a
13. will allow you to check the running time of the lamp the last time that the lamp was On 1 Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that Information is highlighted then press ENTER 2 Press the UP or DOWN buttons until Time Information is dis played press ENTER 3 Press UP or DOWN buttons until Lamp Off Time is displayed and press ENTER ADJ Products LLC www adj com Vizi Beam Hybrid 2R Instruction Manual Page 20 Vizi Beam Hybrid 2R System Menu 4 XXXX will now be displayed XXXX represents the running time of the lamp the last time that the lamp was On 5 Press ENTER or press MODE ESC to exit Last Run Password This will display the timer password 1 Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that Information is highlighted then press ENTER 2 Press the UP or DOWN buttons until Time Information is dis played press ENTER 3 Press UP or DOWN buttons until Last Run Password is dis played and press ENTER 4 The Last Run Password is 038 5 Press ENTER or press MODE ESC to exit Clean Last Run This will allow you to clear the last run time of the unit You need to put in the Last Run Password before doing this Please see the section before this 1 Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that Information is highlight
14. 139 140 159 160 179 180 199 200 219 220 239 240 255 COLOR amp GOBO CHANGE TO ANY POSITION LAMP ON LAMP OFF ALL MOTOR RESET SCAN MOTOR RESET COLOR MOTOR RESET GOBO MOTOR RESET SHUTTER DIMMER MOTOR RESET OTHER MOTOR RESET INTERNAL PROGRAM 1 INTERNAL PROGRAM 2 INTERNAL PROGRAM 3 INTERNAL PROGRAM 4 INTERNAL PROGRAM 5 INTERNAL PROGRAM 6 INTERNAL PROGRAM 7 SOUND ACTIVE PROGRAM 11 0 225 226 235 236 245 BLACKOUT BY WHEEL CHANGING 246 255 NO FUNCTION ADJ Products LLC www adj com Vizi Beam Hybrid 2R Instruction Manual Page 48 ADJ Products LLC www adj com Vizi Beam Hybrid 2R Instruction Manual Page 49 Channel Value Function Channel Value Function GOBOS 48 55 GOBO 6 3 56 63 GOBO 7 4 64 71 GOBO 8 5 GOBO 9 72 79 COLOR WHEEL 80 87 GOBO 10 dee 88 95 GOBO 11 9 17 18 26 27 35 96 103 104 111 112 119 GOBO 12 GOBO 13 GOBO 14 36 44 45 53 54 62 63 71 72 80 81 89 90 98 COLOR 10 120 126 GOBO 1 SHAKE 127 133 GOBO 2 SHAKE 134 140 GOBO 3 SHAKE 141 147 GOBO 4 SHAKE 148 154 GOBO 5 SHAKE 155 161 GOBO 6 SHAKE 162 168 GOBO 7 SHAKE 169 175 GOBO 8 SHAKE 176 182 GOBO 9 SHAKE 183 189 190 196 197 203 204 210 211 217 218 255 GOBO WHEEL ROTATION SLOW FAST 99 107 COLOR 11 108 116 COLOR 12 T17 127 COLOR 13 128 189 FORWARD RAINBOW EFFECT FAST SLOW 190 193 NO ROTATION 194 255 BACKWARDS RAINB
15. 3 94 96 97 99 100 119 120 139 140 159 160 179 180 199 200 219 220 239 240 255 Vizi Beam Hybrid 2R 10 A DMX Mode LAMP o RESET amp PROGRAMS COLOR amp GOBO CHANGE TO ANY POSITION LAMP ON LAMP OFF ALL MOTOR RESET SCAN MOTOR RESET COLOR MOTOR RESET GOBO MOTOR RESET SHUTTER DIMMER MOTOR RESET OTHER MOTOR RESET INTERNAL PROGRAM 1 INTERNAL PROGRAM 2 INTERNAL PROGRAM 3 INTERNAL PROGRAM 4 INTERNAL PROGRAM 5 INTERNAL PROGRAM 6 INTERNAL PROGRAM 7 SOUND ACTIVE PROGRAM www adj com Vizi Beam Hybrid 2R Instruction Manual Page 45 108 116 117 127 Vizi Beam Hybrid 2R 12 Channel DMX Mode PAN MOVEMENT 8bit PAN FINE 16bit TILT MOVEMENT 8bit TILT FINE 16bit COLOR WHEEL OPEN COLOR 1 COLOR 2 COLOR 3 COLOR 4 COLOR 5 COLOR 6 COLOR 7 COLOR 8 COLOR 9 COLOR 10 COLOR 11 COLOR 12 COLOR 13 Vizi Beam Hybrid 2R 64 71 72 79 80 87 88 95 96 103 104 111 112 119 120 126 127 133 134 140 141 147 148 154 155 161 162 168 169 175 176 182 183 189 190 196 197 203 12 Channel DMX Mode Channel Value Function GOBOS CONT GOBO 8 GOBO 9 GOBO 10 GOBO 11 GOBO 12 GOBO 13 GOBO 14 GOBO 1 SHAKE GOBO 2 SHAKE GOBO 3 SHAKE GOBO 4 SHAKE GOBO 5 SHAKE GOBO 6 SHAKE GOBO 7 SHAKE GOBO 8 SHAKE GOBO 9 SHAKE GOBO 10 SHAKE GOBO 11 SHAKE GOBO 12 SHAKE 128 189 FORWARD RAINBOW EFFECT 204 210 GOBO 13 SHAKE FAST SLOW 211 217 G
16. 3 Clean the external optics and mirror with glass cleaner and a soft cloth every 20 days 4 Clean the internal optics with glass cleaner and a soft cloth every 30 60 days 5 Always be sure to dry all parts completely before plugging the unit back in Vizi Beam Hybrid 2R Trouble Shooting Trouble Shooting Listed below are a few common problems that you may encounter with solutions No light output from the unit 1 Be sure the external fuse has not blown The fuse is located on the bottom panel of the unit 2 Remove the lamp holder and be sure the lamp is seated in its socket properly Occasionally lamps become loose during ship ping be sure the lamp is push in to its socket all the way 3 Be sure the fuse holder is completely and properly seated Unit does not respond to sound 1 Low frequencies bass should cause the unit to react to sound Tapping on the microphone quiet or high pitched sounds may not activate the unit ADJ Products LLC www adj com Vizi Beam Hybrid 2R Instruction Manual Page 55 Vizi Beam Hybrid 2R Warranty MANUFACTURER S LIMITED WARRANTY A ADJ Products LLC hereby warrants to the original purchaser ADJ Products LLC products to be free of manufacturing defects in material and workmanship for a prescribed period from the date of purchase see specific warranty period on reverse This warranty shall be valid only if the product is purchased within the United States of America including
17. 3 F or 45 C should now be displayed 113 F represents the temperature that the lamp will restrike at The temperature that is recommended is 113 F 4 Press ENTER to confirm your selection or press MODE ESC to exit Lamp off temp With this function you can set the inside tempera ture at which point the lamp will shut off 1 Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that Lamp Control is highlighted then press ENTER 2 Press the UP or DOWN buttons until Max On at Temp is dis played press ENTER 3 266 F or 130 C should now be displayed 266 F or 130 C represents the temperature that the lamp will automatically switch off at The temperature that is recommended is 266 F 4 Press ENTER to confirm your selection or press MODE ESC to exit NOTE When the temperature around the lamp is higher then the preset value for longer then 5 mins the unit will automatically shut Off the lamp If the lamp is automatically shut off due to over heat it can not be restriked automatically it must be turned On again manually PERSONALITY Time Information Address via DMX With this function you can adjust the DMX address via external controller 1 Press the MODE ESC button to access the main menu Press the ADJ Products LLC www adj com Vizi Beam Hybrid 2R Instruction Manual Page 25 Vizi Beam Hybrid 2R UP or DOWN buttons so that
18. DOWN buttons until Clear Lamp Time is dis played and press ENTER 4 Either Off or On will be displayed use the UP and DOWN but tons to toggle between 5 Press ENTER to confirm your selection or press MODE ESC to exit Temperature Info This will allow you to check the moving head temperature 1 Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that Information is highlighted then press ENTER 2 Press the UP or DOWN buttons until Temperature Info is dis played press ENTER 3 Head Temperature will now be displayed press ENTER 4 XXX will now be displayed XXX represents the current tem perature of the moving head ADJ Products LLC www adj com Vizi Beam Hybrid 2R Instruction Manual Page 22 Vizi Beam Hybrid 2R System Menu 5 Press ENTER or press MODE ESC to exit Software Version This will allow you to see the software version you are currently running 1 Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that Information is highlighted then press ENTER 2 Press the UP or DOWN buttons until Software Version is dis played press ENTER 3 VX X will now be displayed X X represents the software ver sion 4 Press ENTER or press MODE ESC to exit LAMP CONTROL Lamp On Off With this function you can switch the lamp on or off via the control board 1 Pres
19. ER OPEN 0 255 MASTER DIMMER 0 100 0 255 FINE DIMMER INTENSITY ADJ Products LLC www adj com Vizi Beam Hybrid 2R Instruction Manual Page 52 88 90 COLOR MOTOR RESET 91 93 GOBO MOTOR RESET 94 96 SHUTTER DIMMER MOTOR RESET 97 99 OTHER MOTOR RESET 100 119 INTERNAL PROGRAM 1 120 139 INTERNAL PROGRAM 2 140 159 INTERNAL PROGRAM 3 160 179 INTERNAL PROGRAM 4 180 199 INTERNAL PROGRAM 5 200 219 INTERNAL PROGRAM 6 220 239 INTERNAL PROGRAM 7 240 255 SOUND ACTIVE PROGRAM ADJ Products LLC www adj com Vizi Beam Hybrid 2R Instruction Manual Page 53 Vizi Beam Hybrid 2R Lamp Replacement Caution Always replace with the exact same type lamp and fuse unless otherwise specified by an authorized ADJ service technician Replacing with anything other than the specified part can damage your unit and will void your manufactures warranty Warning If you continue to blow lamps or fuses STOP using the unit Contact customer support for further instructions you may have to return the unit for servicing Continuing to use the unit may cause serious damage Lamp Replacement Caution Never attempt to change the lamp while the fixture is plugged in Always disconnect the main power and allow the unit ample time to cool before attempting to replace the lamp Please see page 7 for important information regarding the discharge lamp 1 Be sure to follow the proper handling procedures that deal with discharge lamps 2
20. NTER 3 Either Off or On will be displayed use the UP and DOWN but tons to toggle between Select On if you wish to activate this func tion or Off to deactivate 4 Press ENTER to confirm your selection or press MODE ESC to exit Lamp off via external controller With this function you can select if you want to switch the lamp off via an external controller This is used in conjuction with Internal Programs DMX channel DMX values 60 79 1 Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that Lamp Control is highlighted then press ENTER 2 Press the UP or DOWN buttons until Lamp Off Via DMX is dis played press ENTER 3 Either Off or On will be displayed use the UP and DOWN but tons to toggle between Select On if you wish to activate this func tion or Off to deactivate 4 Press ENTER to confirm your selection or press MODE ESC to exit Max on at temp With this function you can set the inside tempera ture from which the lamp will restrike after automatic shut off ADJ Products LLC www adj com Vizi Beam Hybrid 2R Instruction Manual Page 24 Vizi Beam Hybrid 2R System Menu 1 Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that Lamp Control is highlighted then press ENTER 2 Press the UP or DOWN buttons until Max On at Temp is dis played press ENTER 3 11
21. OBO 14 SHAKE 190 193 NO ROTATION 218 2 BO WHEEL ROTATION 194 255 BACKWARDS RAINBOW EFFECT oa an i SLOW FAST PRISM GOBO MACROS ADJ Products LLC www adj com Vizi Beam Hybrid 2R Instruction Manual Page 46 ADJ Products LLC 0 31 32 79 80 127 128 135 136 143 144 151 152 159 160 167 168 175 OPEN FROST 8 FACET PRISM MACRO 1 MACRO 2 MACRO 3 MACRO 4 MACRO 5 MACRO 6 www adj com Vizi Beam Hybrid 2R Instruction Manual Page 47 Vizi Beam Hybrid 2R 12 Channel DMX Mode Value Function LAMP ON OFF RESET amp PROGRAMS COLOR CHANGE NORMAL COLOR CHANGE TO ANY POSITION Vizi Beam Hybrid 2R 12 Channel DMX Mode Function PRISM GOBO MACROS MACRO 7 MACRO 8 0 19 20 29 176 183 184 191 192 199 200 207 208 215 216 223 224 231 232 239 240 247 248 255 0 127 128 189 190 193 194 255 MACRO 9 MACRO 10 MACRO 11 MACRO 12 MACRO 13 MACRO 14 MACRO 15 MACRO 16 PRISM ROTATION PRISM INDEXING FORWARD PRISM ROTATION FAST SLOW NO ROTATION BACKWARD PRISM ROTATION SLOW FAST SHUTTER amp STROBE SHUTTER CLOSED SHUTTER OPEN STROBING SLOW FAST SHUTTER OPEN PULSE EFFECT IN SEQUENCES SHUTTER OPEN RANDOM STROBE SLOW FAST SHUTTER OPEN 10 DIMMER 0 255 INTENSITY 0 100 PAN TILT MOVEMENT SPEED MAX TO MIN SPEED BLACKOUT BY MOVEMENT 30 39 40 59 60 79 80 84 85 87 88 90 91 93 94 96 97 99 100 119 120
22. OW EFFECT PRISM GOBO MACROS 0 31 OPEN 32 79 FROST 80 127 8 FACET PRISM ADJ Products LLC www adj com Vizi Beam Hybrid 2R Instruction Manual Page 50 ADJ Products LLC 128 135 136 143 144 151 MACRO 1 MACRO 2 MACRO 3 www adj com Vizi Beam Hybrid 2R Instruction Manual Page 51 Vizi Beam Hybrid 2R Channel Value 152 159 160 167 168 175 176 183 184 191 192 199 200 207 208 215 216 223 224 231 232 239 240 247 248 255 16 Channel DMX Mode Function PRISM GOBO MACROS MACRO 4 MACRO 5 MACRO 6 MACRO 7 MACRO 8 MACRO 9 MACRO 10 MACRO 11 MACRO 12 MACRO 13 MACRO 14 MACRO 15 MACRO 16 Vizi Beam Hybrid 2R Channel 15 Value 0 225 226 235 236 245 246 255 0 19 20 29 30 39 40 59 60 79 80 84 85 87 16 Channel DMX Mode Function PAN TILT MOVEMENT SPEED MAX TO MIN SPEED BLACKOUT BY MOVEMENT BLACKOUT BY WHEEL CHANGING NO FUNCTION LAMP ON OFF RESET amp PROGRAMS COLOR CHANGE NORMAL COLOR CHANGE TO ANY POSITION COLOR amp GOBO CHANGE TO ANY POSITION LAMP ON LAMP OFF ALL MOTOR RESET SCAN MOTOR RESET PRISM ROTATION PRISM INDEXING FORWARD PRISM ROTATION FAST SLOW NO ROTATION BACKWARD PRISM ROTATION 10 0 127 128 189 190 193 194 255 SLOW FAST SHUTTER amp STROBE SHUTTER CLOSED SHUTTER OPEN STROBING SLOW FAST SHUTTER OPEN PULSE EFFECT IN SEQUENCES SHUTTER OPEN RANDOM STROBE SLOW FAST SHUTT
23. Thank you Table of Contents UPPER nnmnnn iinn hana eaa a AEE aieiaa 3 AEFOQUCHON ani 3 Customer SUPPOH starai 3 Safety ProC utiOnS 0 sccssssscssccssctsssessaeessssevsssssstsnsssnsseaseens 4 FEAlUlS osato 5 Handling Presaullons en iin 6 Pre ONS Tra 1021 1 RAR NT 6 Important Discharge Lamp Warnings i 7 MOOMIN Gissi RR DE AAA 8 Controls and FUNCHOnSs sci 10 PA 13 System Mehl iii 16 Error COS 38 Opodo rai 40 DE 42 Lamp Replacement cuiiiciiiiini iii 54 Fuse ReplaCeMEnt i 54 Cleaning arere RA 55 Trouble Smootiai naar 55 VEE ARRE RR SA 56 SDOCIICAU ONS svircicicccatscnxnacinendansiunab cian tesasecdanasaadencidaacagaienatit 57 Please see page 7 for important lamp instructions ADJ Products LLC www adj com Vizi Beam Hybrid 2R Instruction Manual Page 2 Vizi Beam Hybrid 2R General Information Unpacking Thank you for purchasing the Vizi Beam Hybrid 2R by ADJ Products LLC Every Vizi Beam Hybrid 2R has been thoroughly tested and has been shipped in perfect operating condition Carefully check the shipping carton for damage that may have occurred during shipping If the carton appears to be damaged carefully inspect your fixture for any damage and be sure all equipment necessary to oper ate the unit has arrived intact In the event damage has been found or parts are missing please contact our toll free customer support number for further instructions Please do not return
24. WN but tons to toggle between 5 Press ENTER to confirm your selection or press MODE ESC to exit Tilt Reverse With this function you can reverse the Tilt movement 1 Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that Personality is highlighted then press ENTER 2 Press the UP or DOWN buttons until Status Setting is dis played press ENTER 3 Press UP or DOWN buttons until Tilt Reverse is displayed and ADJ Products LLC www adj com Vizi Beam Hybrid 2R Instruction Manual Page 27 Vizi Beam Hybrid 2R System Menu press ENTER 4 Either Off or On will be displayed use the UP and DOWN but tons to toggle between 5 Press ENTER to confirm your selection or press MODE ESC to exit Pan Degree With this function you can change the pan degree from 630 to 540 1 Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that Personality is highlighted then press ENTER 2 Press the UP or DOWN buttons until Status Setting is dis played press ENTER 3 Press UP or DOWN buttons until Pan Degree is displayed and press ENTER 4 Either 540 or 630 will be displayed use the UP and DOWN buttons to toggle between 5 Press ENTER to confirm your selection or press MODE ESC to exit Feedback With this function you can feedback switch the pan movement or tilt movement 1 Press the MODE ESC
25. button to access the main menu Press the UP or DOWN buttons so that Personality is highlighted then press ENTER 2 Press the UP or DOWN buttons until Status Setting is dis played press ENTER 3 Press UP or DOWN buttons until Feedback is displayed and press ENTER 4 Either Off or On will be displayed use the UP and DOWN but tons to toggle between 5 Press ENTER to confirm your selection or press MODE ESC to exit ADJ Products LLC www adj com Vizi Beam Hybrid 2R Instruction Manual Page 28 Vizi Beam Hybrid 2R System Menu Movement Speed With this function you can set the pan and tilt movement speed 1 Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that Personality is highlighted then press ENTER 2 Press the UP or DOWN buttons until Status Setting is dis played press ENTER 3 Press UP or DOWN buttons until Movement Speed is dis played and press ENTER 4 Either Speed 1 Speed 2 Speed 3 or Speed 4 will be dis played use the UP and DOWN buttons to toggle between 5 Press ENTER to confirm your selection or press MODE ESC to exit Mic Sensitivity With this function you can set the microphone sensitivity The default setting is 70 You can adjust the sensitivity between 0 99 1 Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that Personality is hi
26. cts LLC www adj com Vizi Beam Hybrid 2R Instruction Manual Page 10 Vizi Beam Hybrid 2R Controls and Functions 1 Lens Assembly A high quality lens 2 Digital Display This display shows the menu and operating func tions that you can choose from 3 Microphone This microphone receives external low frequencies to trigger the unit in Sound Active mode This microphone is designed to receive low frequency sounds only tapping on the microphone and high pitch sounds may not trigger the unit 4 Left Button This button is used to move to the left when navigat ing through the system menu 5 Down Button This button is used to scroll backwards when navi gating through the system menu 6 Right Button This button is used to move to the right when navi gating through the system menu 7 Mode Esc Button This button is used to enter the main menu and submenus It is also used to exit 8 Up Button This button is used to scroll forwards when navigating through the system menu 9 Enter Button This button is used to select and confirm a function in the system menu 10 Carrying Handles The includes built in carrying handles Be sure to always handle the unit by the built in handles Never lift or car rying the unit by head or yoke Pulling on or transporting the unit by the moving head may severely damage the unit and will void the unit warranty 11 Lamp Assembly and Access Plate This plate accesses the lam
27. d Using the UP or DOWN buttons select Master and press ENTER 5 For your Slave units access the main menu and press the UP or DOWN buttons so that Function is highlighted then press ENTER 6 Press the UP or DOWN buttons until Slave Mode is displayed and press ENTER 7 Either Slave 1 Slave 2 or Slave 3 will be displayed Select your desired Slave setting and press ENTER 5 Press MODE ESC if you want to return to the main menu 6 You may change the show or invert the pan and tilt functions in the system menu by following the directions on pages 26 27 ADJ Products LLC www adj com Vizi Beam Hybrid 2R Instruction Manual Page 41 ADJ Products LLC 126 189 190 193 194 255 Vizi Beam Hybrid 2R 10 Channel DMX Mode OPEN COLOR 1 COLOR 2 COLOR 3 COLOR 4 COLOR 5 COLOR 6 COLOR 7 COLOR 8 COLOR 9 COLOR 10 COLOR 11 COLOR 12 COLOR 13 FORWARD RAINBOW EFFECT FAST SLOW NO ROTATION BACKWARDS RAINBOW EFFECT SLOW FAST www adj com Vizi Beam Hybrid 2R Instruction Manual Page 42 ADJ Products LLC Vizi Beam Hybrid 2R 96 103 104 111 112 119 120 126 127 133 134 140 141 147 148 154 155 161 162 168 169 175 176 182 183 189 190 196 197 203 204 210 211 217 218 255 0 31 32 79 80 127 128 135 136 143 144 151 152 159 160 167 168 175 176 183 184 191 192 199 200 207 10 Channel DMX Mode Channel Val
28. ed then press ENTER 2 Press the UP or DOWN buttons until Time Information is dis played press ENTER 3 Press UP or DOWN buttons until Clean Last Run is displayed and press ENTER 4 Either Off or On will be displayed use the UP and DOWN but tons to toggle between 5 Press ENTER to confirm your selection or press MODE ESC to exit Lamp Time Password This will display the lamp timer password 1 Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that Information is highlighted then press ENTER ADJ Products LLC www adj com Vizi Beam Hybrid 2R Instruction Manual Page 21 Vizi Beam Hybrid 2R System Menu 2 Press the UP or DOWN buttons until Time Information is dis played press ENTER 3 Press UP or DOWN buttons until Lamp Time Password is dis played and press ENTER 4 The Lamp Time Password is 038 5 Press ENTER or press MODE ESC to exit Clean Lamp Time This will allow you to clear the lamp time run ning time Please clear the lamp running time every time you replace the lamp You need to put in the Lamp Time Password before doing this Please see the section before this 1 Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that Information is highlighted then press ENTER 2 Press the UP or DOWN buttons until Time Information is dis played press ENTER 3 Press UP or
29. ed then press ENTER 2 Press the UP or DOWN buttons until Service Settings is dis played press ENTER 3 Press UP or DOWN buttons until Password is displayed and press ENTER 4 The Password is 050 5 Press ENTER or press MODE ESC to exit RDM PID RDM stands for Remote Device Management This feature lets you control every aspect of your fixture remotely from an RDM controller Manual settings like adjusting the DMX address are no longer needed This is especially useful when the unit is installed in a remote area In this submenu you can see the units RDM ID number and adjust it as well 1 Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that Personality is highlighted then press ENTER ADJ Products LLC www adj com Vizi Beam Hybrid 2R Instruction Manual Page 30 Vizi Beam Hybrid 2R 2 Press the UP or DOWN buttons until Service Settings is dis played press ENTER 3 Press UP or DOWN buttons until RDM PID is displayed and press ENTER 4 XXXXXX will be displayed XXXXXX represents the units current RDM ID 5 Press ENTER or press MODE ESC to exit System Menu Fans Control Auto Fan Speed With this function you can adjust the speed of the running fans 1 Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that Personality is highlighted then press ENTER 2 Press the UP
30. ee customer sup port number All packages returned to the service department not dis playing a R A number on the outside of the package will be returned to the shipper at the shippers cost Product Registration ADJ Products LLC www adj com Vizi Beam Hybrid 2R Instruction Manual Page 6 Vizi Beam Hybrid 2R Important Discharge Lamp Warning This fixture is fitted with a discharge lamp which is highly susceptible to damage if improperly handled Never touch the lamp with your bare fingers as the oil from your hands will shorten lamp life Also never move the fixture until the lamps have had ample time to cool Remember lamps are not covered under warranty conditions SEC ov This unit emits intense UV radiation which is harmful to the eyes and skin The intense luminance of the lamp can cause severe damage to the retina Never operate this unit without it s covers these covers have been specially designed to shield against UV radiation Epileptic Warning Those suffering from epilepsy should avoid looking directly into the lamp at all times Avoid switching the fixture on and off repeatedly in short intervals as this will reduce lamp life and intensity To achieve the intensity associated with discharge lamps these lamps use gas sealed in a high pressure environment to emit a brilliant output Due to the high pressure involved with the construction of the lamp the lamp may explode during prolonged exten
31. ghlighted then press ENTER 2 Press the UP or DOWN buttons until Status Setting is dis played press ENTER 3 Press UP or DOWN buttons until Mic Sensitivity is displayed and press ENTER 4 70 will be displayed use the UP and DOWN buttons to adjust the sensitivity between 0 99 5 Press ENTER to confirm your selection or press MODE ESC to exit Hibernation With this function the lamp and step motors will power off if there is no DMX signal within 15 mins factory defualt Once it receives a DMX signal the fixture will reset itself 1 Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that Personality is highlighted then press ADJ Products LLC www adj com Vizi Beam Hybrid 2R Instruction Manual Page 29 Vizi Beam Hybrid 2R System Menu ENTER 2 Press the UP or DOWN buttons until Status Setting is dis played press ENTER 3 Press UP or DOWN buttons until Hibernation is displayed and press ENTER 4 15M will be displayed use the UP and DOWN buttons to adjust the hibernation period between 01M 99M or Off 5 Press ENTER to confirm your selection or press MODE ESC to exit Service Setting Password With this function you can enter the RDM password so that you can access and change the RDM ID number 1 Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that Personality is highlight
32. he basic operations of this unit These instructions contain important safety information regard ing the use and maintenance of this unit Please keep this manual with the unit for future reference General Instructions Vizi Beam Hybrid 2R Caution There are no user serviceable parts inside this unit Do not attempt any repairs yourself doing so will void your manufactures warranty In the unlikely event your unit may require service please contact ADJ Products LLC During operation the housing may become extremely hot Avoid touching the unit with bare hands while in use Handling Precautions ADJ Products LLC will not accept any liability for any resulting dam ages caused by the non observance of this manual or any unauthor ized modification to this unit Vizi Beam Hybrid 2R The Vizi Beam Hybrid 2R carries a one year limited warranty Please fill out the enclosed warranty card to validate your purchase All returned service items whether under warranty or not must be freight pre paid and accompany a return authorization R A number The R A number must be clearly written on the outside of the return pack age A brief description of the problem as well as the R A number must also be written down on a piece of paper and included in the shipping carton If the unit is under warranty you must provide a copy of your proof of purchase invoice You may obtain a R A number by contacting our customer support team on our toll fr
33. ion when using several DMX fixtures try to use the shortest cable path possible The order in which fixtures are connected in a DMX line does not influence the DMX addressing For example a fixture assigned a DMX address of 1 may be placed anywhere in a DMX line at the beginning at the end or anywhere in the middle Therefore the first fixture controlled by the controller could be the last fixture in the chain When a fixture is assigned a DMX address of 1 the DMX controller knows to send DATA assigned to address 1 to that unit no matter where it is located in the DMX chain Data Cable DMX Cable Requirements For DMX and Master Slave Operation The Vizi Beam Hybrid 2R can be controlled via DMX 512 protocol The Vizi Beam Hybrid 2R can be either a 10 12 or 16 channel DMX unit The DMX address is set electronically using the controls on the front panel of the unit Your unit and your DMX controller require a approved DMX 512 110 Ohm Data cable for data input and data output Figure 1 We recommend Accu Cable DMX cables If you are making your own cables be sure to use stan dard 110 120 Ohm shielded cable This cable may be purchased at almost all professional sound and lighting stores Your cables should be made with a male and female XLR connector on either end of the cable Also ADJ Products LLC www adj com Vizi Beam Hybrid 2R Instruction Manual Page 13 Vizi Beam Hybrid 2R Set Up remember that DMX cable must be da
34. is missing or there is a stepper motor failure defective motor or a defective motor IC drive on the main PCB O3Er TILT movement error This message will appear after a fixture reset if the tilt mag netic indexing circuit malfunctions sensor failed or magnet is ADJ Products LLC www adj com Vizi Beam Hybrid 2R Instruction Manual Page 38 Vizi Beam Hybrid 2R Error Codes missing or there is a stepper motor failure defective motor or a defective motor IC drive on the main PCB O5Er COLOR WHEEL error This message will appear after a fixture reset if the head s mag netic indexing circuit malfunctions Sensor failed or magnet is missing or there is a stepper motor failure defective motor or a defective motor IC drive on the main PCB O6Er FIXED GOBOS error This message will appear after a fixture reset if the magnetic indexing circuit malfunctions Sensor failed or magnet is miss ing or there is a stepper motor failure defective motor or a defective motor IC drive on the main PCB ADJ Products LLC www adj com Vizi Beam Hybrid 2R Instruction Manual Page 39 Vizi Beam Hybrid 2R Operation Universal DMX Control This function allows you to use a uni versal DMX 512 controller such as the Elatione DMX Operator or Elatione Show Designer to control head movement the color wheel gobo wheel prism master dimmer shutter strobe and vari ous other features A DMX controller allows you to create uniq
35. isy chained and cannot be split Notice Be sure to follow figures two and three when making your own cables Do not use the ground lug on the XLR connector Do not con nect the cable s shield conductor to the ground lug or allow the shield conductor to come in contact with the XLR s outer casing Grounding the shield could cause a short circuit and erratic behavior COMMON DMX512 OUT DMX512 IN 3 PIN XLR DMX 3 PIN XLR Figure 2 XLR Female Socket I 2 RO i I I I I I I I I I I XLR Male Socket 1 Ground E 2 Cold Figure 3 XLR Pin Configuration Pin 1 Ground Pin 2 Data Compliment negative pai eae eae el all cio Pin 3 Data True positive Special Note Line Termination When longer runs of cable are used you may need to use a terminator on the last unit to avoid erratic behavior A terminator is a 110 120 ohm 1 4 watt resistor which is con nected between pins 2 and 3 of a male XLR connector DATA and DATA This unit is inserted in the female XLR connector of the last unit in your daisy chain to terminate the line Using a cable terminator ADJ part number Z DMX T will decrease the possibilities of erratic behavior Termination reduces signal errors and avoids signal transmission problems o and interference It is always advisable Z p to connect a DMX terminal Resistance 120 Ohm 1 4 W between PIN 2 DMX g and PIN 3 DMX of the last fixture Figure 4 ADJ Products
36. ith this function the internal program will run in sound active mode 1 Access the main menu and press the UP or DOWN buttons so that Function is highlighted then press ENTER 2 Press the UP or DOWN buttons until Sound Control is dis played press ENTER 3 Either Master or Alone will be displayed Use the UP or DOWN buttons to change the operating mode ADJ Products LLC www adj com Vizi Beam Hybrid 2R Instruction Manual Page 18 Vizi Beam Hybrid 2R System Menu 4 Press ENTER to to make your selection or press MODE ESC button to exit INFORMATION Time Information Time information is always represented in hours Current Running Time This will allow you to check units current running time 1 Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that Information is highlighted then press ENTER 2 Press the UP or DOWN buttons until Time Information is dis played press ENTER 3 Press UP or DOWN buttons until Current Time is displayed and press ENTER 4 XXXX will now be displayed XXXX represents the current run ning time 5 Press ENTER or press MODE ESC to exit Total Running Time This will allow you to check units total running time 1 Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that Information is highlighted then press ENTER 2 Press the UP or DOWN buttons unti
37. l Time Information is dis played press ENTER 3 Press UP or DOWN buttons until Total Run Time is displayed and press ENTER 4 XXXX will now be displayed XXXX represents the total run ning time 5 Press ENTER or press MODE ESC to exit Last Run Time This will allow you to check the last running time of the lamp ADJ Products LLC www adj com Vizi Beam Hybrid 2R Instruction Manual Page 19 Vizi Beam Hybrid 2R System Menu 1 Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that Information is highlighted then press ENTER 2 Press the UP or DOWN buttons until Time Information is dis played press ENTER 3 Press UP or DOWN buttons until Last Run Time is displayed and press ENTER 4 XXXX will now be displayed XXXX represents the last running time 5 Press ENTER or press MODE ESC to exit Lamp Hours This will allow you to check the running time of the lamp 1 Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that Information is highlighted then press ENTER 2 Press the UP or DOWN buttons until Time Information is dis played press ENTER 3 Press UP or DOWN buttons until Lamp Hours is displayed and press ENTER 4 XXXX will now be displayed XXXX represents the lamp run ning time 5 Press ENTER or press MODE ESC to exit Lamp Off Time This
38. layed and press ENTER 4 Either Off or On will be displayed use the UP and DOWN but tons to toggle between 5 Press ENTER to confirm your selection or press MODE ESC to exit Key Lock With this function activated the buttons will lock autom matically after 15 seconds 1 Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that Personality is highlighted then press ENTER 2 Press the UP or DOWN buttons until Display Setting is dis played press ENTER 3 Press UP or DOWN buttons until Key Lock is displayed and press ENTER 4 Either Off or On will be displayed use the UP and DOWN but tons to toggle between 5 Press ENTER to confirm your selection or press MODE ESC to exit Temperature C F With this function you can change the tempera ture display to show either Celsius or Fahrenheit ADJ Products LLC www adj com Vizi Beam Hybrid 2R Instruction Manual Page 32 Vizi Beam Hybrid 2R System Menu 1 Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that Personality is highlighted then press ENTER 2 Press UP or DOWN buttons until Temperature C F is dis played and press ENTER 3 Either Celsius or Fahrenheit will be displayed use the UP and DOWN buttons to toggle between 4 Press ENTER to confirm your selection or press MODE ESC to exit Initial Status In this me
39. nd under no circumstances shall ADJ Products LLC be liable for any loss or damage direct or consequential arising out of the use of or inability to use this product This warranty is the only written warranty applicable to ADJ Products LLC Products and supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore published MANUFACTURER S LIMITED WARRANTY PERIODS Lighting Products 1 year 365 days Limited Warranty Such as Special Effect Lighting Intelligent Lighting UV lighting Strobes Fog Machines Bubble Machines Mirror Balls Par Cans Trussing Lighting Stands etc excluding LED and lamps e Laser Products 90 Day Limited Warranty e L ED Products 3 year 1095 days Limited Warranty excluding motors PCB boards and power supplies which have a 1 year 365 day Limited Warranty and batteries which have a 180 day limited warranty Only the L E D s carry a 3 year warranty ADJ Products LLC www adj com Vizi Beam Hybrid 2R Instruction Manual Page 56 Vizi Beam Hybrid 2R Notes ADJ Products LLC www adj com Vizi Beam Hybrid 2R Instruction Manual Page 57 Vizi Beam Hybrid 2R Specifications Model Vizi Beam Hybrid 2R Voltage 100 240V 50 60Hz Lamp Philips Platinum MSD 2R Discharge Power Consumption 210W Dimensions 16 75 L x 12 5 W x 9 25 H 420mm x 306mm x 289mm Colors 13 Plus White Gobos 14 Spot Weight 23 Lbs 10 kgs Fuse 5A
40. nges in the user defined modes that are created in the previous function EDIT PROGRAM The fixture comes equipped with a built in DMX recorder that allows custom programs to be installed and recalled directly from the fixture s control board Programs can be created and stored using the fixture s control board or by using an external DMX controller Select Program This function allows the user to select one of ten of the user defined built in programs This program is then accessed in Function Mode under Program Run Edit Program This function allows the user to edit the built in pro grams Edit Scenes This function allows the user to edit or define the actual scenes that are stored in the user defined built in programs that are accessed in the previous step Rec Controller The Vizi Beam Hybrid 2R features an integrated DMX recorder Preprogrammed scenes can be transmitted to the fixture via any DMX compliant controller This function allows those scenes to be stored in to the fixture s built in memory and then subsequently used to create the user defined programs ADJ Products LLC www adj com Vizi Beam Hybrid 2R Instruction Manual Page 37 Vizi Beam Hybrid 2R Error Codes When power is applied the unit will automatically enter a reset test mode This mode brings all the internal motors to a home position If there is an internal problem with one or more of the motors an error code will flash in
41. ns For Your Own Personal Safety Please Read and Understand This Manual Completely Before You Attempt To Install Or Operate This Unit To reduce the risk of electrical shock or fire do not expose this unit rain or moisture Do not spill water or other liquids into or on to your unit Be sure that the local power outlet match that of the required volt age for your unit Do not attempt to operate this unit if the power cord has been frayed or broken Do not attempt to remove or break off the ground prong from the electrical cord This prong is used to reduce the risk of electrical shock and fire in case of an internal short Disconnect from main power before making any type of connection Do not remove the cover under any conditions There are no user serviceable parts inside Never operate this unit when it s cover is removed Always be sure to mount this unit in an area that will allow proper ventilation Allow about 6 15cm between this device and a wall Do not attempt to operate this unit if it becomes damaged This unit is intended for indoor use only use of this product out doors voids all warranties Always mount this unit in safe and stable matter Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them paying particular attention to cords at plugs convenience recep tacles and the point where they exit from the appliance Cleaning The fixtu
42. nu you are able to check initial effect posi tion 1 Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that Personality is highlighted then press ENTER 2 Press the UP or DOWN buttons until Initial Status is displayed press ENTER 3 XXX will be displayed XXX represents the current effect posi tion 4 Press ENTER or press MODE ESC to exit Reset Default 1 Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that Personality is highlighted then press ENTER 2 Press the UP or DOWN buttons until Reset Default is displayed press ENTER 3 Either Off or On will be displayed use the UP and DOWN but tons to toggle between 4 Press ENTER to confirm your selection or press MODE ESC to exit RESET FUNCTION Reset All With this function you can all the motors ADJ Products LLC www adj com Vizi Beam Hybrid 2R Instruction Manual Page 33 Vizi Beam Hybrid 2R System Menu 1 Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that Reset Function is highlighted then press ENTER 2 Press the UP or DOWN buttons until Reset All is displayed press ENTER 3 Press ENTER to confirm your selection or press MODE ESC to exit Rest Pan amp Tilt With this function you can reset the Pan amp Tilt motors 1 Press the MODE ESC button to access the main menu Press
43. ord XXX Lamp Password 038 Clean Lamp Time ON OFE Clear lamp time Temperature Info _ Head Temperature XXXC F Temperature in the head Software Version V1 0 Software version Lamp On Off ON OFF Lamp on off 8 Automatic On ON OFF Lamp on off Power on amp Lamp On via DMX ON OFF Lamp on via DMX amp Lamp Off via DMX ON OFF Lamp off via DMX 3 Max Onat Temp 20 79 C AG 68 174F ER Lamp restart at temp Lamp Off Temp 80 139 C M80 176 282 F B66E Lamp off at temp Status Settings Address Via DMX ON OFF Add via DMX No DMX Status Close H IW Auto Music Auto run if no DMX Pan Reverse ON OFE Pan Reverse movement Tilt Reverse ON OFE Tilt Reverse movement Pan Degree 630 540 Pan Degree Select Feedback ON OFF Movement Feedback Movement Speed Speed I 4 Movement Mode Select Mic Sensitivity 0 99 Sensitivity of Mic Hibernation OFF 01M 99M SM Stand by Mode Service Setting Password Password XXX Service Password 050 3 RDM PID XXXKXX RDM PID Code Fans Control Auto Fan Speed Fans Speed select PAN CHOI Display Setting Shutoff Time 02 60m 05m Display shutoff time Display Reverse ON OFF Reverse 180 degree Key Lock ON OFF Key Lock Temperature C F Celsius Temperature switch Fahrenheit between C Initial Status PAN XXX Initial effect position Reset Default ON OFF Restore factory set Reset All Reset all motors 3 Reset Pan amp Tilt Reset Pan Tilt Reset Colors Reset color
44. p socket assembly The unit includes a spring mounted discharge lamp Be sure to only replace with same type lamp After replacing a lamp be sure the lamp is centered in the reflector See pages 52 53 for details on installing and optimizing replacement lamps Never operate this unit with the lamp exposed this lamp emits strong UV radiation Please see page 7 for important information about the Philips Plati num 5R discharge lamp 12 XLR DMX Input Jack This jack is used to receive an incoming ADJ Products LLC www adj com Vizi Beam Hybrid 2R Instruction Manual Page 11 Vizi Beam Hybrid 2R Controls and Functions DMxX signal or Master Slave signal 13 XLR Output Jack This jack is used to transmit the incoming DMX signal to another DMX fixture or transmit a Master Slave signal to the next Vizi Beam Hybrid 2R in the chain For best results in DMX or Master Slave mode terminate this jack if it is the last unit in the chain See Line Termination on page 14 14 Power Cord Inlet This cord is designed to match the electri cal requirements of the unit Voltage may vary from venue to venue when connecting this unit to a power supply be sure to connect to a matching power outlet Never use this fixture if the ground prong has been removed or broken off The ground prong is designed to reduce the risk of fire or electrical shock in the event the unit suffers from an internal short Fuse Holder This housing stores a 5 amp protec
45. re should be cleaned only as recommended by the manufacturer See page 55 for cleaning details Heat This fixture should be situated away from heat sources such as radiators heat registers stoves or other appliances including amplifiers that produce heat The fixture should be serviced by qualified service personnel when A Objects have fallen or liquid has been spilled into the appliance B The appliance has been exposed to rain or water C The appliance does not appear to operate normally or exhibits a marked change in performance ADJ Products LLC www adj com Vizi Beam Hybrid 2R Instruction Manual Page 4 Vizi Beam Hybrid 2R Features Micro Stepping Motors for Smooth Color and Gobo Transitions 3 Modes of DMX 512 Protocol Compatible 10 DMX Channel Mode 12 DMX Channel Mode and 16 DMX Channel Mode Independent Gobo and Color Wheels 14 Gobos Spot 12 Colors Plus White With Rainbow RDMX Lets you set the DMX address from any DMX Controller 3 Operating Modes Master Slave Stand Alone Sound Active Internal Microphone Philips Platinum MSD 2R Discharge Edit and Save Scenes into the Memory 360 540 Pan Movement 270 Tilt Movement Digital Display for Address and Function Setting ADJ Products LLC www adj com Vizi Beam Hybrid 2R Instruction Manual Page 5 Vizi Beam Hybrid 2R To optimize the performance of this product please read these operating instructions carefully to familiarize yourself with t
46. s currently assingned to the unit If you want the set the address to 420 set Channel 1 s value to 7 Channel 2 s value to 8 and Channel 3 s to 164 256 164 420 No DMX status With this function if the DMX signal is suddenly ADJ Products LLC www adj com Vizi Beam Hybrid 2R Instruction Manual Page 26 Vizi Beam Hybrid 2R System Menu lost the unit will automatically go into 1 of 3 modes 1 Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that Personality is highlighted then press ENTER 2 Press the UP or DOWN buttons until Status Setting is dis played press ENTER 3 Press UP or DOWN buttons until No DMX Status is displayed and press ENTER 4 Either Hold Last DMX setting Close Blackout Music Sound Active or Auto Auto Program will be displayed use the UP and DOWN buttons to toggle between 5 Press ENTER to confirm your selection or press MODE ESC to exit Pan Reverse With this function you can reverse the Pan movement 1 Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that Personality is highlighted then press ENTER 2 Press the UP or DOWN buttons until Status Setting is dis played press ENTER 3 Press UP or DOWN buttons until Pan Reverse is displayed and press ENTER 4 Either Off or On will be displayed use the UP and DO
47. s the MODE ESC button to access the main menu Press the UP or DOWN buttons so that Lamp Control is highlighted then press ENTER 2 Press the UP or DOWN buttons until Lamp Off On is displayed press ENTER 3 Either Off or On will be displayed use the UP and DOWN but tons to toggle between 4 Press ENTER to confirm your selection or press MODE ESC to exit Automatic On With this function you can have the lamp automati cally turn On when when switching on the power 1 Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that Lamp Control is highlighted then press ENTER 2 Press the UP or DOWN buttons until Automatic On is displayed press ENTER 3 Either Off or On will be displayed use the UP and DOWN but tons to toggle between ADJ Products LLC www adj com Vizi Beam Hybrid 2R Instruction Manual Page 23 Vizi Beam Hybrid 2R System Menu 4 Press ENTER to confirm your selection or press MODE ESC to exit Lamp on via external controller With this function you can select if you want to switch the lamp on via an external controller This is used in conjuction with Internal Programs DMX channel DMX values 40 59 1 Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that Lamp Control is highlighted then press ENTER 2 Press the UP or DOWN buttons until Lamp On Via DMX is dis played press E
48. sive use This risk is increased with age added care is encouraged when dealing with older lamps Extreme caution should be used when operating this or any fixture fitted with a gas discharge lamp Never open this unit while in use VERY IMPORTANT This is for your safety and the life length of the unit The Philips Platinum 2R Discharge lamp has lifetime of 6 000 hours Because of the nature of the extreme heat associated with the Platinum 2R lamp and the tight nature of the internal optical system it is imperative that the lamp be replaced every 6000 hours This is done to protect the internal optical system as well as prevent accidental lamp explosion which could lead to hot glass particles falling from the fix ture Failure to change the lamp within 300 hours of operation will result in automatic shut down of the fixture s electronics At 6000 hours the display will begin to flash Replace The Lamp and the lamp will flicker for the first five minutes of operation At this point the lamp has reached the maximum rated life and should be replaced immediately After the lamp has flickered for about five minutes it should strike normally allowing the fixture to be used tempo rarily until a replacement lamp can be installed The fixture will continue to operate for an additional 300 hours however the Replace the Lamp warning will continue to flash in the display Keep in mind that the flicker protection circuitry will only work for abo
49. the unit on its side as illustrated above Be sure this fixture is kept at least 0 5m away from any flammable materials decoration etc Always use and install the supplied safety cable as a safety measure to prevent accidental damage and or injury in the event the clamp fails see next page Never use the carrying handles for secondary attachment ADJ Products LLC www adj com Vizi Beam Hybrid 2R Instruction Manual Page 8 Vizi Beam Hybrid 2R NOTICE The suitable enviromental temperature for this light ing fixture is between 25 C to 45 C Do not place this lighting fixture in an enviroment where the temperatures are under or above the temperatures stated above This will allow the fixture to run at its best and help prolong the fixture life Mounting 1 Omega holders 2 Clamp 3 Safety rope 4 Quick lock fastener Screw one clamp each via a M12 screw and nut onto the Omega holders Insert the quick lock fasteners of the first Omega holder into the respective holes on the bottom of the Vizi Beam Hybrid 2R Tighten the quick lock fasteners fully clockwise Install the second Omega holder Pull the safety cable through the holes on the bottom of the base and over the trussing system or a safe fixation spot Insert the end in the carabine and tighten the safety screw ADJ Products LLC www adj com Vizi Beam Hybrid 2R Instruction Manual Page 9 Vizi Beam Hybrid 2R Controls and Functions FRONT REAR ADJ Produ
50. this unit to your dealer without contacting customer support first Introduction The Vizi Beam Hybrid 2R is a DMX intelligent moving head fixture The Vizi Beam Hybrid 2R can be a 10 channel 12 chan nel or 16 Channel DMX unit The fixture can operate in three different operating modes show mode sound active or under DMX control The Vizi Beam Hybrid 2R can be used as a stand alone unit or ina master slave configuration For best results use fog or special effects smoke to enhance the beams projections During the initial start up or use of this product a light smoke or smell may arise from the unit This is a normal process and is cause by the heat associated with the lamp Customer Support ADJ Products LLC provides a toll free cus tomer support line to provide help and to answer any question should you encounter problems during your set up or initial operation You may also visit us on the web at www adj com for any comments or suggestions Service Hours are Monday through Friday 8 00 a m to 4 30 p m Pacific Standard Time Voice 800 322 6337 Fax 323 582 2610 E mail support americandj com Warning To prevent or reduce the risk of electrical shock or fire do not expose this unit to rain or moisture Warning This may cause severe eye damage Avoid looking directly into the light source at all times ADJ Products LLC www adj com Vizi Beam Hybrid 2R Instruction Manual Page 3 Vizi Beam Hybrid 2R Safety Precautio
51. tive fuse Never defeat the fuse the fuse is designed to protect the electronics in the event of severe power fluctuations Always be sure to replace the fuse with an exact match as the one being replaced unless otherwise told to do so by an authorized ADJ service technician 15 Power Switch This switches the power to the fixture On amp Off ADJ Products LLC www adj com Vizi Beam Hybrid 2R Instruction Manual Page 12 Vizi Beam Hybrid 2R Set Up Power Supply The ADJ Vizi Beam Hybrid 2R contains a electronic ballast which will auto sense the voltage when it is plugged into the power source With the electronic ballast you do not need to worry about wall voltage this unit can be plugged in anywhere DMX 512 DMX is short for Digital Multiplex This is a universal pro tocol used by most lighting and controller manufactures as a form of communication between intelligent fixtures and controllers A DMX controller sends DMX data instructions from the controller to the fix ture DMX data is sent as serial data that travels from fixture to fixture via the DATA IN and DATA OUT XLR terminals located on all DMX fixtures most controllers only have a DATA OUT terminal DMX Linking DMX is a language allowing all makes and models of different manufactures to be linked together and operate from a single controller as long as all fixtures and the controller are DMX compliant To ensure proper DMX data transmiss
52. ue Function GOBOS CONT GOBO 12 GOBO 13 GOBO 14 GOBO 1 SHAKE GOBO 2 SHAKE GOBO 3 SHAKE GOBO 4 SHAKE GOBO 5 SHAKE GOBO 6 SHAKE GOBO 7 SHAKE GOBO 8 SHAKE GOBO 9 SHAKE GOBO 10 SHAKE GOBO 11 SHAKE GOBO 12 SHAKE GOBO 13 SHAKE GOBO 14 SHAKE GOBO WHEEL ROTATION SLOW FAST PRISM GOBO MACROS OPEN FROST 8 FACET PRISM MACRO 1 MACRO 2 MACRO 3 MACRO 4 MACRO 5 MACRO 6 MACRO 7 MACRO 8 MACRO 9 MACRO 10 www adj com Vizi Beam Hybrid 2R Instruction Manual Page 43 Vizi Beam Hybrid 2R 10 Channel DMX Mode 208 215 216 223 224 231 232 239 240 247 248 255 0 127 128 189 190 193 194 255 Channel Value Funtion er MACROS MACRO 11 MACRO 12 MACRO 13 MACRO 14 MACRO 15 MACRO 16 PRISM ROTATION PRISM INDEXING FORWARD PRISM ROTATION FAST SLOW NO ROTATION BACKWARD PRISM ROTATION SLOW FAST SHUTTER amp STROBE SHUTTER CLOSED SHUTTER OPEN STROBING SLOW FAST SHUTTER OPEN PULSE EFFECT IN SEQUENCES SHUTTER OPEN RANDOM STROBE SLOW FAST 7 SHUTTER OPEN DIMMER 0 255 INTENSITY 0 100 PAN TILT MOVEMENT SPEED MAX TO MIN SPEED BLACKOUT BY MOVEMENT BLACKOUT BY WHEEL CHANGING NO FUNCTION 1 LAMP ON OFF RESET amp PROGRAMS 0 19 COLOR CHANGE NORMAL 20 29 COLOR CHANGE TO ANY POSITION ADJ Products LLC www adj com Vizi Beam Hybrid 2R Instruction Manual Page 44 ADJ Products LLC 30 39 40 59 60 79 80 84 85 87 88 90 91 9
53. ue pro grams tailored to your individual needs 1 The Vizi Beam Hybrid 2R has a 10 Channel mode 12 Channel mode and 16 Channel mode See pages 42 53 for detailed description of the DMX traits 2 To control your fixture in DMX mode follow the set up procedures on pages 13 15 as well as the set up specifications that are included with your DMX controller Use the controller s faders to control the various DMX fixture traits This will allow you to create your own programs Follow the directions on page 36 to select your DMX Channel mode and follow the instruction on page 17 to set the DMX address 6 For longer cable runs more than a 100 feet use a terminator on the last fixture 7 For help operating in DMX mode consult the manual included with your DMX controller nn Stand Alone Sound Active or Auto Program This mode allows a single unit to run to the beat of the music or run through a built in program AUTO PROGRAM 1 Access the main menu and press the UP or DOWN buttons so that Function is highlighted then press ENTER 2 Press the UP or DOWN buttons until Auto Program is dis played and press ENTER 3 Either Master or Alone will be displayed Using the UP or DOWN buttons select Alone and press ENTER SOUND ACTIVE 1 Access the main menu and press the UP or DOWN buttons so that Function is highlighted then press ENTER 2 Press the UP or DOWN buttons until So
54. und Control is dis played press ENTER 3 Either Master or Alone will be displayed Using the UP or ADJ Products LLC www adj com Vizi Beam Hybrid 2R Instruction Manual Page 40 Vizi Beam Hybrid 2R Operation DOWN buttons select Alone and press ENTER Master Slave Operation Sound Active or Auto Program This function will allow you to link up to 16 units together and oper ate without a controller The units can run a built in program or run in sound actiive mode In Master Slave operation one unit will act as the controlling unit and the others will react to the controlling units pro grams Any unit can act as a Master or as a Slave 1 Using standard XLR microphone cables daisy chain your units together via the XLR connector on the rear of the units Remem ber the Male XLR connector is the input and the Female XLR connector is the output The first unit in the chain master will use the female XLR connector only The last unit in the chain will use the male XLR connector only For longer cable runs we suggest a terminator at the last fixture 2 On your Master unit access the main menu and press the UP or DOWN buttons so that Function is highlighted then press ENTER 3 Select your desired operating mode Use the UP or DOWN but tons to select between Auto Program or Sound Control press ENTER to select your desired program 4 Either Master or Alone will be displaye
55. unit as the slave in ADJ Products LLC www adj com Vizi Beam Hybrid 2R Instruction Manual Page 17 Vizi Beam Hybrid 2R System Menu a Master Slave configuration 1 Access the main menu and press the UP or DOWN buttons so that Function is highlighted then press ENTER 2 Press the UP or DOWN buttons until Slave Mode is displayed and press ENTER 3 Either Slave 1 Slave 2 or Slave 3 will be displayed Press ENTER to select either of the three or press MODE ESC button to exit Auto Program This function allows the internal programs to run in either stand alone or master slave mode In Master mode the fix ture will send DMX data to other fixtures connect via the DMX chain In Alone mode the fixture will operate as a single fixture The pro gram for this mode is selected in the Select program section of the control menu You can set the number of steps under Edit pro gram You can edit the individual scenes under Edit scenes With this function you can run the individual scenes either automatically i e with the adjusted Step Time 1 Access the main menu and press the UP or DOWN buttons so that Function is highlighted then press ENTER 2 Press the UP or DOWN buttons until Auto Program is displayed and press ENTER 3 Either Master or Alone will be displayed 4 Press ENTER to to make your selection or press MODE ESC button to exit Sound Control W
56. ut 300 hours lamp clock life of 6000 6300 hours After 6300 hours the fixture will no longer respond to DMX commands and immediately enter a hibernation mode that will electronically discontinue all fixture functionality with the exception of a few menu commands The fixture will continue to enter hibernation mode until the lamp is replaced and the lamp clock has been reset See page 22 to Clear the lamp time ADJ Products LLC www adj com Vizi Beam Hybrid 2R Instruction Manual Page 7 Vizi Beam Hybrid 2R When installing the unit the trussing or area of installation must be able to hold 10 times the weight without any deformation When installing the unit must be secured with a secondary safety attach ment e g and appropriate safety cable Never stand directly below the unit when mounting removing or servicing the unit Mounting Overhead mounting requires extensive experience including calculat ing working load limits installation material being used and perodic safety inspection of all installation material and unit If you lack these qualifications do not attempt the installation yourself These installaiton should be checked by a skilled person once a year The Vizi Beam Hybrid 2R is fully operational in two different mounting positions hanging upside down from a ceiling or set on a flat level surface To avoid internal damage to the unit never mount
57. uttons to scroll through the various func tions Press ENTER when you find the function you would like to adjust 4 Press ENTER or press MODE ESC to exit Calibration With this function you can calibrate and adjust the effects wheels to their correct positions The Calibration password 050 1 Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that Effect Adjust is highlighted then press ENTER 2 Press the UP or DOWN buttons until Calibration is displayed press ENTER 3 XXXX will be displayed The password is 050 4 Press ENTER to confirm or press MODE ESC to exit USER MODE SET User Mode 1 Press the MODE ESC button to access the main menu Press the UP or DOWN buttons so that User Mode Set is highlighted then press ENTER 2 Press the UP or DOWN buttons until User Mode is displayed press ENTER 3 Use the UP or DOWN buttons to scroll through the 3 DMX Channel Modes ADJ Products LLC www adj com Vizi Beam Hybrid 2R Instruction Manual Page 36 Vizi Beam Hybrid 2R System Menu Standard Mode This is 12 Channel Mode Basic Mode This is 10 Channel Mode Extended Mode This is 16 Channel Mode 4 Press the MODE ESC button once to return to the User Mode Set menu Use the UP or DOWN buttons to scroll through the Edit modes Press ENTER to select any of the Edit modes Edit User Mode This function allows the user to make the actual cha
58. wheel 5 Reset Gobos Reset gobos Reset Shutter Reset shutter or dimmer Reset Others Reset other motors Test Channel PAN sis Test function z Manual Control PAN XXX Fine adjustment of the gt lamp Calibration Calibrate Password Password 050 Color wheel XXX Calbrate and adjust the a effects to standard right position User Mode Standard Mode Basic Mode 2 Extended Mode User s mode to change 3 User Mode A channel numbers Ss User Mode B 5 User Mode C 5 Edit User Mode Max Channel XX Preset User modes Select Programs Auto Pro Part 1 Program 1 10 Program Auto Pro Part 2 Program 1 10 BORAMA Auto Pro Part 3 Program I 10 Piogams Select programs to be run Edit Program Program 1 Program Test Step 01 SCxxx Program 10 Step 64 SCxxx Testing program Program in loop Save and exit Edit Scenes Edit Program Edit Scene 001 Pan Tilt Edit Scene Fade Time 250 Secne Time Input By Exterior Save and automatically return manual scenes edit Rec Controller XX XX Automat scenes rec ADJ Products LLC www adj com Vizi Beam Hybrid 2R Instruction Manual Page 16 Vizi Beam Hybrid 2R System Menu The main menu is accessed by pressing the MODE ESC button Browse through the menu by using the UP DOWN RIGHT amp LEFT buttons Press the ENTER button to access the desired menu You can scroll through the submenus using the UP DOWN RIGHT
Download Pdf Manuals
Related Search