Quick Start Guide - AC Lighting Inc.
Contents
1. 1200Hz 2400Hz 4800Hz 9600Hz DMX Lost When DMX is not detected select from the output options Last Data No Output Reset to user saved or default settings see User Manual 7 Further Information Please refer to the Chroma Q Inspire Terminal Strip manual for more detailed information A copy of the manual can be found at the Chroma Q website www chroma g com under Support Inspire Terminal Strip Quick Start Guide V1 01 Inspire Terminal Strip Quick Start Guide V1 012. America Tel 44 0 1494 446000 Tel 1 416 255 9494 Fax 44 0 1494 461024 Fax 1 416 255 3514 support chroma q com support chroma q com For further information please visit the Chroma Q website at www chroma qg com ae Chroma Q and Inspire Terminal Strip are trademarks for more information on this visit www chroma q com trademarks The rights and ownership of all trademarks are recognised Chroma Q BRILLIANT SOLUTIONS For a full product manual please visit www chroma q com Software Version 1 01 Inspire Terminal Strip Quick Start Guide V1 01 Inspire Terminal Strip Quick Start Guide V1 01 PN 632 0707 1 Overview The new Chroma Q Inspire Terminal Strip LED house light features a single light engine with 36 high powered LEDs RGBW a fully homogenized optic and controlled via the Inspire External Control Box Through the Inspire External Control Box the fixture can be controlled remotely through the ANSI E1 11 USITT DMX 512 A protocol 2 safety 1 This product is for professional use only It is NOT intended for domestic or outdoor use AN 2 The bright flash of light during power up amp continuous strobe may cause epileptic seizure Caution 3 This product must be used with a safety cable 3 Cabling System Diagram Figure 1 a Maximum DMX cable AC r lt pom Power In Data Out4 eee Units per line o length from Data Out Data Out 2 1 2 3 to the 1st fixture Data Out 3 must not exceed Inspir
3. Approvals amp Disclaimer Quick Start Guide C 4 Chroma Q The information contained herein is offered in good faith and is believed to be accurate However Inspire 1 Terminal otrip because conditions and methods of use of our products are beyond our control this information should not be used in substitution for customer s tests to ensure that Chroma Q products are safe effective and fully satisfactory for the intended end use Suggestions of use shall not be taken as inducements to infringe any patent Chroma Q sole warranty is that the product will meet the Chroma Q sales specifications in effect at the time of shipment Your exclusive remedy for breach of such warranty is limited to refund of purchase price or replacement of any product shown to be other than as warranted Chroma Q reserves the right to change or make alteration to devices and their functionality without notice due to on going research and development The Chroma Q Inspire range has been designed specifically for the lighting industry Regular maintenance should be performed to ensure that the products perform well in the entertainment environment If you experience any difficulties with any Chroma Q products please contact your selling dealer If your selling dealer is unable to help please contact support chroma q com If the selling dealer is unable to Satisfy your servicing needs please contact the following for full factory service Outside North America North
4. e 5007 152m Terminal Strip fixtures Inspire External Control Box Note Emergency Power In is the input connection from an alternative power source for emergency ii tl 1 Note The DMX cable connected to the first Terminal Strip fixture from each Data Output of the External Control Box must be terminated with a 120 ohm resistor See Inspire Terminal Strip User Manual for details DMX OUT DMX IN Power amp Data Connections Figure 2 HOLE FOR POWER beeen EOC ie ener CABLE WITH Xe rev CCR OEE STRAIN RELIEF TIN k POWER INPUT COVER PLATE Inspire Terminal Strip Quick Start Guide V1 01 Power Input Figure 3 paos U ROERE r D LIVE w NEUTRAL amp re a oid c GROUND SHIELD Ke fer ase men DATA MINUS IDATAPLUS To connect the wiring for power and control data Remove the cover plate for power input e Insert the AC power cable with strain relief through the cover plate and connect to the Terminal Block Plug and into the Terminal Block header in the fixture Figure 2 amp 3 Put back and fasten the cover plate e Connect the DMX control data cables from the Inspire External Control Box to the Terminal Block Plug and plug into the Terminal Block headers at the rear of the fixture Figure 2 amp 4 4 Mounting A mounting bracket is built into the enclosure for overhead applications Secure the fixture with a safety bond A f
5. ixing hold is built into the enclosure 5 Optics The Inspire can be built with either Narrow Medium or Wide lens The beam angles are Narrow 32 Medium 42 Wide 65 6 Control The control functions are accessed through the Touch Screen display at the front panel of the Inspire External Control Box The features of the Touch Screen Display are Ps Model Name Chroma Q P DMX Indicator INSPIRE External Control S me AC Power Indicator j Emergency Power Indicator DMX Start Address Mode Setun Menu waw cnroma q com er Port DMX Add 1 Port2 DMX Add 1_ Port3 DMX Add 1 select control functions and options Command Buttons can be tapped to Control Menu Main Menu Displays the model name DMX information AC and Emergency power input and Command buttons Address sets the DMX start address for each output Output 1 Output 2 Output 3 Inspire Terminal Strip Quick Start Guide V1 01 Mode select from the control mode options RGBW single 4 channels x RGBW for each fixture in each output up to 512 channels per output RGBW output 4 channels x RGBW for all fixtures in each output 1 channel x W for all fixtures in each output Lookstore Save and Load a Look setup Menu set the internal settings of the Inspire External Control DMX Data Displays DMX values RotateDisp Change the display orientation Frequency To change the LED scan rate frequency select from
Download Pdf Manuals
Related Search