TS240 User Manual
Contents
1. Cleaning Scan Head Steps Note This is only performed when document images are unclear distorted or have a dark line laterally through every image Use the cleaning swab or a clean cloth to wipe the camera faceplate the two white strips and both sides of the camera faceplate section of the scanner The covers lift off vertically Unscrew the nylon screw and gently open the scanner camera faceplates Reassemble the scanner components by replacing the nylon screw and the covers Note The swabs are typically used to clean off the four main drive rollers but can also be used on the scanheads if you have a tough buildup on the glass 18 Oo DIGITAL CA CHECK Common Error Codes From The Scanner There are three common error codes that can typically show up depending upon the type of documents being scanned Periodic and scheduled cleanings should be performed before determining if any further problem determination is needed See the scanner cleaning document Helpful Hints 1 Always hand jog the documents to align the leading and bottom edges for the auto feed models Visually check the leading edges for bent or curled or curled corners and straighten them as needed 2 Place the stack of documents half way into the entry slot then slide the stack forward until the LED light comes on turns orange 3 Be sure that the entry tray is fully seated and that the exit wire stop is extended2. continued Insert a new TellerScan cleaning card in the entry pocket Open the imaging application and initiate feeding while holding the card firmly to prevent the card from actually feeding through the scanner You will want to cancel the transaction after running several scan cycles Note You may use the remote deposit application to run the scanner during the cleaning cycle or the ScanLite demo program available from the Digital Check web site Important Run a scan cycle and hold onto the card but allow it to move into the path so that the second set of rollers is scrubbing on the cleaning card Flip the card over and run the same procedure again This ensures that the main entry drive roller and the double feed rollers are being properly cleaned Getting the rollers to scrub on the cleaning cards is the most important part of the cleaning procedure Rollers with a severe buildup of ink and dirt will require use of the swabs to be used to manually scrub all four of the main drive rollers 17 Flip the card top to bottom and scan the card again this time letting it move through the scanner into the exit pocket Turn the card around and repeat the same process of scanning the card several times on the reverse side Result The TellerScan cleaning card should have been run through the scanner three to four times periodically flipping the card or swapping it end for end DIGITAL CHECK _
3. DIGITAL LN Q CHECK TellerScane 240 Countertop Check Scanner User Manual June 2010 Rev 061110 g DIGI TAL i oo P i gt gt r lt CUoOECK TellerScan 240 Operator Maintenance Cleaning the TellerScan 240 Over time ink dirt and dust particles will collect on the scanner rollers and document track Therefore it is necessary to clean these areas on a regular basis to assure reliable performance Tips for performing preventative maintenance by the user on the TellerScan TS240 include see the TS240 Routine Maintenance amp Troubleshooting video at www digitalcheck com for additional info e A Periodic inspection of the entire document track area The use of flashlight will enhance the visual inspection between the scanheads and throughout the document track e Remove any staples paper clips and rubber bands that may have accumulated during use e Have a can of compressed air available to blow out the document track on a regular basis e Purchase the TellerScan cleaning cards available at digitalcheck com to have on hand for regular cleaning maintenance Run several scan cycles flipping the card between cycles while holding the card to scrub the first drive or entry rollers Once the entry rollers no longer deposit dirt onto the card allow the card to scan through the entire path Run this through several times while flipping the card end to
4. e debris paper or a staple in the path Check if the document s leading edge looks OK or is catching on something All of the main drive rollers may need to be cleaned 20 No Checks There are no checks indicated in the entry pocket A scan cycle has been initiated but the LED is not on indicating that documents are present Restack the batch of documents and insert them back into the entry pocket Slide them forward until the LED comes on This typically can happen when a scan cycle is initiated and the LED is not on No Print Head The ink jet cartridge is not being sensed by the scanner When endorsing characters using the ink jet option the print string is the first function sent down to the scanner at the start of a scan cycle This error will come up immediately if no cartridge is present Open the center cover by lifting vertically Remove and reseat the ink jet cartridge being sure it snaps into place If that fails try using a new cartridge No Scanner The scanner was not found during the application to scanner initialization The right LED must be on and Red for the application to acquire the unit Check the USB cable connections or try a different cable Try a different USB port Verify that the PC has the proper drivers and the scanner firmware file is installed i D IGITAL Additional Scanner Information There are other helpful documents available in PDF format on
5. end and top to bottom see the TS240 Routine Maintenance amp Troubleshooting video at www digitalcheck com for additional info e Use the special cleaning swabs which come with the TellerScan cleaning kit to scrub the four drive rollers under the center cover e Inspect the quality of the captured images on a regular basis If the image quality drops off inspect and clean the scanheads following the procedure described later in this manual If the quality does not appear to be related to dirt or debris contact your service provider to determine if the scanheads can be recalibrated 14 gg DIGITAL Cleaning your Scanner s Rollers Magnetic Head and Camera Faceplates In severe environments where ink and dirt build up rapidly it may be necessary to clean the scanner rollers magnetic read head scan head faceplates and document track every 3 000 to 5 000 documents This simple maintenance will dramatically improve the reliability of your scanner over its useful life Scanner Cleaning Supplies to order visit www digitalcheck com or call 847 446 2285 1 Compressed Air acquired from a local office supply provider 2 Cleaning Cards Consisting of one box of 25 cleaning cards IS0028 3 Cleaning Kit Consisting of box of 25 cleaning cards amp 6 cleaning swabs 130007 03 Cleaning The TellerScan 240 using ScanLite Software The ScanLite program which is available from the Digital Check web site
6. enough to allow for approximately 72 more than the longest document 19 Mis Feed The documents failed to leave the entry pocket on time Remove the documents and re align the leading edges Check for bent or excessively curled leading edges and straighten as needed Verify that documents are not stuck together Insert and rescan the documents If they continue to get 216 errors this might indicate that o The entry drive rollers may be dirty o Something may also be lodged in the path Double Document Feed More than one document is detected amp passed into the exit pocket Check the exit pocket for a double document feed If the document is still in the path grab the upper edges with both hands and wiggle the document back and forth vertically to remove it If they continue to get 217 errors this might indicate o The entry drive rollers may need to be cleaned o Check the condition of the documents for bent edges Replace the inside double feed roller and retest Document Stopped in the path A document stopped in the path or was slow in exiting Eject the documents To clear the error condition If the document will not eject grab the upper edges with both hands and wiggle the document back and forth vertically to remove it from the path Check the leading edges and corners of the document and straighten as needed A 220 error code where the document is stopping in the path repeatedly could indicat
7. is an excellent utility to run while performing the cleaning procedures recommended below ScanLite provides an easy way to initiate the scan cycles in order to feed the cleaning cards properly through the scanner ScanLite also includes an Eject button that operates the scanner at half its normal speed making it easy to scrub off the four main drive rollers when using the cleaning swabs Visit the following site to download ScanLite nttp www digitaleheck com integration_support drivers_and_demo_ programs 15 DIGITAL CHECK _ i Cleaning Steps i Helpful Hints 1 Do not use stickers to cover up previously sprayed numbers on documents The Use compressed air to clean the document backing from the stickers can rub off onto track as illustrated below the rollers and cause documents to jam 2 Do not use White Out on scanned documents the White Out can rub off the documents onto the scanner camera faceplate and distort the images 3 Watch for loose debris falling into the scanner such as staples and rubber bands 4 Carefully turn the scanner upside down You may need to remove the center or outer and shake it to remove any loose debris covers to check for other debris that may have entered the scanner Using two hands pull straight up on the center and left side covers to remove See the section below for removing the rear right cover 16 DIGITAL CHECK e _ Cleaning Steps
8. nnections If the LED is Red but will not turn Green contact customer support for assistance with checking firmware and reloading the drivers What is a safe distance to keep the power supply from the TS240 check scanner to prevent electromagnetic interference with the MICR read head in the scanner Keep power supplies and other electromagnetic devices 12 18 inches away from the scanner to keep them from interfering with the Magnetic read head How often should the TS240 check scanner be cleaned The recommended cleaning cycle is every 3 000 to 5 000 items in severe environments where ink and dirt may build up quickly Please reference the cleaning instructions section for specific instructions on how to properly clean the TS240 How long will the inside double feed roller last From 200 000 300 000 items depending on the condition of the documents How many characters does the HP C6602A inkjet cartridge yield Once opened the practical life of the inkjet cartridge is six months However the rated character yield on the inkjet cartridge is between 5 7 million characters Do not shake or drop the cartridge which can cause the printing to fail Keep a spare cartridge on hand in case the current cartridge cannot be used What are the minimum and maximum document dimensions for the TS240 See the able below 21
9. the Digital Check web site Go to http www digitalcheck com The ink jet cartridge used in the TS240 is the standard HP C6602A cartridge Typical yield is from 5 to 7 million characters The TS240 scanner is recommended to use a USB 2 0 port for optimum performance and application timing For support contact your dealer or Digital Check Corporation at 847 446 2285 The Service request form to send scanners into the plant for repair can be filled out on line by going to the web site at www digitalcheck com clientarea NOTE Periodic and scheduled cleanings should be performed before determining if any further problem determination is needed See the scanner cleaning section N f I a d gt k n_ lt l Xv D Frequently Asked Questions How many checks per minute should my TS240 scan The TS240 has a rated throughput speed of up to 50 75 or 100 documents per minute DPM depending on the specific model TS240 50 TS240 75 TS240 100 Actual throughput will vary depending on the PC configuration physical size of the items scanned simple or complex endorsement and the speed of the application What is the proper sequence of the LED lights when the scanner is powered on The proper LED sequence is for the LED to come on Red followed by the LED turning green once the application has been launched If the LED does not come on Red check the power and USB cable co
Download Pdf Manuals
Related Search