RS0103 Rolling shutter controller user manual A0
Contents
1. VIE AR i fat Pam gt Il 7 BAXTER i i Q 7 ig O ro HOG SEFF NE Gje Cs NO W EAR ey gt MRR ER Fa ay wae pt EN o o TZ i key AL 24 VDC Hit NRF I GND a es O Ola JE n O Jo 24VACHIA conn She BR fit FA 4 1 DIP Switch ON DIP 1 DIP 2 DIP 3 DIP 4 Auto close Buzzer beeps Increase the photocell function is on after every sensitivity of 5 OFF protection is when DIP 1 operation when resistance when 1 23 4 on when DIP at ON DIP 2 at ON DIP 3 at ON 4 at off 4 2 Limit switch port J2 External limit switch NC contact otherwise cannot open or close door 4 3 Motor Port J8 J9 direction when connects J8 switch J8 with J9 and motor will run in negative direction They are used for changing the running direction of motor If motor runs in positive 4 4 External switch of control It s single button control the same as port J3 on button board and controls MEIR the motor veering stop reversal stop 4 5 Photocell protection switch G o p gt 24VDC 4 HL It is only available when door is closing if the signal is AT ee eee es LHD IER Blocked during closing door motor stops and door will PU reverse to limit point Q pe OND 1 Photocell protection switch could be point contact O Or two wire type both are NC EOF 2 Photocell protection is off if DIP 4 at ON G tas PG EE ZT Ab IEE CF2. 4 6 Anti theft switch It connects NC switch and J5 port is at 23VDC alarm It will the alarm if the door is forced to open when the door is closed to the limit The port could be short circuit by shorting stub if this function is unused BEER V Setting up process Make sure the connection is correct according to the connection diagram Erasing transmitter Ref 5 2 Learning transmitter ref 5 3 Adjustment Make the resistance into medium position before it hotocell not working Photocell works well Check ref 5 5 closing is not correct Plug the motor wire Direction of opening and closing is correct in another port Limit of opening and closing door is not correct Limit of opening and closing door is correct Check ref 5 4 Resistance adjustment for opening and closing door Adjust potentiometer Direction of opening and PT1 PT2 to change the opening closing resistance Resistance increases when adjust it C W Resistance is not i appropriate Resistance is appropriate Finish the set up 5 1 Single remote button control press open press stop press close press stop 5 2 Erasing transmitter Press the learning button continue pressing for 8s until light turns off Release learning button light will be on about 1s and then off The erasing process is successful ignore this step if transmitter already matches the opener before delivery 5 3 Learning transmitter Pr
3. RS0103 Rolling shutter controller user manual AO I Technical parameters 1 Working voltage 24V AC 2 Temperature range 20 C to 60 C 3 Loading capacity 100W 24VDC 4 Built in fuse motor 10A electric circuit 0 5A please exchange appropriate fuse according to loading capacity 5 Working frequency 433 92MHz 6 Stored transmitters 6pcs II Safety Instruction 1 For security please read instructions carefully before initial operation making sure that the power connection Please clear the memory before initial operation Ref Erasing ALL learned memorized Transmitters 3 Do not learn the remote control when motor is operating in order to avoid mis operation 4 The received signal may be interfered by other communication devices e g the wireless control system frequency range 5 Itis forbidden to control the high risk coefficient equipment system e g cranes 6 It is used only for the manual remote control and wireless control equipment system which must not er property during running failure or its security risks have been eliminated 7 It should be applied in dry indoor place or in the electric appliance place Ill Size gt ES ky m TI IV Connection REG SER HETT See ed Ea 7 TEIE
4. any more
5. ess learning button S2 in the board LED 2 turns on and it enters into the learning memorizing transmitter process press the same button twice in transmitter light blinks for several times then off The learning process is successful ignore this step if transmitter already matches the opener already 5 4 Limit is wrong 1 check if the wires of the limit are connecting well or connect the other way 2 make sure the door can touch the limit switch when open or close the door fully 5 5 Photocell protect switch 1 Only work when closing 2 connects normally close switch of photocell protection 3 If the emitter and receiver module work well If the contact disconnect when the signed is blocked 5 6 Resistance adjustment Adjust potentiometer of opening door to change the opening and closing resistance Adjust potentiometer of closing door to change the closing resistance Make a resistance to door after the adjustment in order to check if it is appropriate VI Operating process Press transmitter button 1 Motor works in the positive direction open Press transmitter Open limit Open button 1 point resistance Press transmitter button 1 Motor works in the negative direction close Press transmitter Photocell Close button 1 resistance VII Note 7 1 Battery life is about 6 12 month User needs to replace with new battery if the indicated light in remote control is not working
Download Pdf Manuals
Related Search