Home

Christie LWU420 User Manual

1. 25 LWU420 User Manual Network Guide 020 000263 01 Rev 1 06 2010 CHAISTIE 3 1 Configuring and controlling the projector via a web browser continued 3 1 10 Projector Control The items shown in the table below can be performed using the Projector Control menu Select an item using the up and down arrow keys on the PC Most of the items have a submenu Refer to the table below for details o ze Ss S 3 NOTE The setting value may not match with the actual value if the user changes the value manually In that case please refresh the page by clicking Refresh button Controls the projector Description Main Power Turns the power on off Input Source Selects the input source Picture Mode Selects the picture mode setting Blank On Off Turns Blank on off Mute Turns Mute on off Freeze Turns Freeze on off Magnify Controls the magnify setting In some input signal sources it might stop Magnify even though it does not reach to maximum setting value Template Turns template on off P by P Turns the P by P on off P by P Left Source Selects the P by P Left Source setting P by P Right Source Selects the P by P Right Source setting P by P Main Area Selects the P by P Main Area Source setting MY Image Select MY IMAGE data MY Image Delete LWU420 User Manual Network Guide Delet
2. Fig 3 1 1 a Logon Menu Below are the factory default settings for Administrator ID User ID and passwords Item ID Password Administrator Administrator lt blank gt User User lt blank gt If the logon is successful either the Fig 3 1 1 b or Fig 3 1 1 c screen will be displayed Main menu Main menu 2 ne ee nd ge ZE gas SE Fig 3 1 1 b Logon with Administrator ID Fig 3 1 1 c Logon with User ID 3 Click the desired operation or configuration item on the main menu located on the left hand side of the screen LWU420 User Manual Network Guide 13 020 000263 01 Rev 1 06 2010 CHAISTIE 3 1 Configuring and controlling the projector via a web browser continued 3 1 2 Network Information _ All screen drawings in this manual are shown when you logon with the Administrator ID Any functions that are available only for the Administrator will not be shown when you logon with the User ID Refer to the table 412 13 Displays the projector s current network configuration settings Item Description Projector Name Displays the projector name settings DHCP Displays the DHCP configuration settings IP Address Displays the current IP address Subnet Mask Displays the subnet mask Default Gateway Displays the default gateway MAC Address Displays the ethernet MAC address Displays the network firmware time stamp This information is only disp
3. 1 byte lt Projector busy reply gt Connection ID 2 bytes 1 byte Status code lt Authentication error reply gt Authentication Connection Error code ID 1 byte 43 LWU420 User Manual Network Guide 020 000263 01 Rev 1 06 2010 CHAISTIE 3 6 Command Control via the Network continued Automatic Connection Break The TCP connection will be automatically disconnected after there is no communication for 30 seconds after being established Authentication The projector does not accept commands without authentication success when authentication is enabled The projector uses a challenge response type authentication with an MD5 Message Digest 5 algorithm When the projector is using a LAN a random 8 bytes will be returned if authentication is enabled Bind this received 8 bytes and the Authentication Password and digest this data with the MD5 algorithm and add this in front of the commands to send Following is a sample if the Authentication Password is set to password and the random 8 bytes are a572f60c 1 Select the projector 2 Receive the random 8 bytes a572f60c from the projector 3 Bind the random 8 bytes a572f60c and the Authentication Password password and it becomes a572f60cpassword 4 Digest this bind a572f60cpassword with MD5 algorithm It will be e3d97429adffa11bce1f7275813d4bde 5 Add this e3d97429adff
4. Cycle information from the SNTP server hour minute Click Apply button to save the settings NOTE The new configuration settings are activated after restarting the network connection When the configuration settings are changed you must restart the network connection You can restart the network connection by clicking Network Restart on the main menu e If you connect the projector to an existing network consult a network administrator before setting server addresses e To enable the SNTP function the time difference must be set e The projector will retrieve Date and Time information from the time server and override time settings when SNTP is enabled e The internal clock s time may not remain accurate Using SNTP is recommended to maintain accurate time 23 LWU420 User Manual Network Guide 020 000263 01 Rev 1 06 2010 CHAISTIE 3 1 Configuring and controlling the projector via a web browser continued 3 1 9 Security Settings Pr 221 E A aa Pi 4 R Displays and configures passwords and other security settings Item Description Administrator authority Configures the Administrator ID and password Configures the Administrator ID Administrator ID The length of the text can be up to 32 alphanumeric characters Configures the Administrator password The length of the text can be up to 255 alphanumeric characters Administrator Password Re enter Administ
5. LAN or High Speed Internet ina Loza rea Connection cable unplugged Netvor ANMA PCI E Ap IntelR PRO 1000 NT Mobile Netwark Connections System Folder Fig 2 2 2 b Network Connections window LWU420 User Manual Network Guide 5 020 000263 01 Rev 1 06 2010 CHAISTIE 2 2 Manual network connection setting continued 5 Open Local Area Connection Properties window you use for network device Fig 2 2 2 c Local Area Connection Properties General Authentication Advanced Connect using E9 Intel R PRO 1000 MT Mobile Connection This connection uses the following items A Network Monitor Driver Install Uninstall Description Transmission Control Protocol Intemet Protocol The default wide area network protocol that provides communication across diverse interconnected networks Show icon in notification area when connected Cers Fig 2 2 2 c Local Area Connection Properties window 6 Set used protocol as TCP IP and open Internet Protocol TCP IP Properties window Internet Protocol TCP IP Properties General You can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for the appropriate IP settings Obtain a address automaticall Uze the following IP address IP address Subnet mask Default gateway Alternat
6. You can adjust or control the projector via a network from a web browser on a PC that is connected to the same network NOTE Internet Explorer 5 5 or later is required e If JavaScript is disabled in your web browser configuration you must enable JavaScript in order to use the projector web pages properly See the Help files for your web browser for details on how to enable JavaScript e You can communicate using SSL Secure Socket Layer if you are using Windows XP Service Pack 2 or earlier versions of Microsoft Windows Please specify https when you enter the IP address of the projector on the web browser You can t communicate the projector using SSL on Windows Vista e It is recommended that all web browser updates are installed It is especially recommended that all users running Internet Explorer on a Microsoft Windows version prior to Windows XP Service Pack 2 install security update Q832894 MS04 004 or the web browser interface may not be displayed correctly And when using an earlier version of Internet Explorer during operations the browser will log out after 50 seconds 11 LWU420 User Manual Network Guide 020 000263 01 Rev 1 06 2010 CHAISTIE 3 1 Configuring and controlling the projector via a web browser continued When configuring or controlling the projector via a web browser an ID and password are required There are two types of IDs Administrator ID and User ID The following chart describes the
7. name if the valid DNS server is setup in the Network Settings The maximum length of host or domain name is up to 255 characters Configures the sender e mail address Sender E mail address The length of the sender e mail address can be up to 255 alphanumeric characters Configures the e mail address of up to five recipients You can also specify TO or CC for each address The length of the recipient e mail address can be up to 255 alphanumeric characters Recipient E mail address Click Apply button to save the settings NOTE You can confirm whether the mail settings work correctly using Send Test Mail button Please enable Send mail setting before clicking Send Test Mail e If you connect the projector to an existing network consult a network administrator before setting server addresses 17 LWU420 User Manual Network Guide 020 000263 01 Rev 1 06 2010 CHAISTIE 3 1 Configuring and controlling the projector via a web browser continued 3 1 6 Alert Setting i Alert Settings Cover Error Displays and configures failure amp alert settings Item Description Cover Error The lamp cover has not been properly fixed Fan Error The cooling fan is not operating The lamp does not light and there is a possibility that interior portion has become heated There is a possibility that the interior portion has become heated Air Flow Error The internal temperature is rising
8. 100 alphanumeric characters Except Cold Start and Authentication Failure Configures the text of the e mail to be sent The length of the text can be up to 1024 alphanumeric characters Except Cold Start and Authentication Failure Alarm Time Send Mail Mail Subject Mail Text Click Apply button to save the settings NOTE The trigger of Filter Error e mail is depending on the FILTER MESSAGE setting in the SERVICE item of the OPTION Menu which defines the period until the filter message is displayed on the projector screen The e mail will be sent when the filter timer exceeds 500 1000 1500 or 2000 hours based on the configuration No notification e mail will be sent if the FILTER MESSAGE is set to TURN OFF EQOPTION Menu in the User s Manual detailed Operating Guide e Lamp Time Alarm is defined as a threshold for e mail notification reminder of the lamp timer When the lamp hour exceeds this threshold that is configured through the Web page the e mail will be sent out e Filter Time Alarm is defined as a threshold for e mail notification reminder of the filter timer When the filter hour exceeds this threshold the e mail will be sent out LWU420 User Manual Network Guide 020 000263 01 Rev 1 06 2010 CHAISTIE 3 1 Configuring and controlling the projector via a web browser continued 3 1 7 Schedule Settings B EEN a le Settings Daily Displ
9. 4 appears it succeeds Fig 2 2 4 Logon Menu LWU420 User Manual Network Guide 020 000263 01 Rev 1 06 2010 CHAISTIE a MEMEC OMEN UTEN IONNS SNES This projector is equipped with the following network functions by using a web browser software Configuring and Controlling the Projector via a Web Browser You can change the settings of or control the projector via a network by using a web browser from a PC that is connected to the same network 11 E mail Alerts The projector can automatically send an alert to specified e mail addresses when the projector requires maintenance or has encountered an error 032 Projector Management using SNMP This projector is SNMP Simple Network Management Protocol compliant allowing you to monitor it from a remote location using SNMP software In addition the projector is able to send failure amp warning alerts to a specified PC 034 Event Scheduling You can schedule the projector to perform various functions according to the date and time G35 MY IMAGE Still Image Transfer Display The projector can display still images that are transferred via the network 20138 Command Control via the Network The projector can be controlled using RS 232C commands over a network 40 LWU420 User Manual Network Guide 020 000263 01 Rev 1 06 2010 CHAISTIE 3 1 Configuring and controlling the projector via a web browser
10. gateway can be blank e When the projector and PC exist in different networks default gateway setting is necessary Contact the network administrator in detail Setting automatically When DHCP server exists in network it is possible to assign IP address to the projector and PC automatically DHCP is abbreviation for Dynamic Host Configuration Protocol and has the function to provide necessary setting for network like IP address from server to client A server that has DHCP function is called DHCP server LWU420 User Manual Network Guide 020 000263 01 Rev 1 06 2010 CHAISTIE 2 Equipment connection and network setting 2 2 Manual network connection setting continued 2 2 3 Internet Option setting 1 Click Internet Options in Network and Internet Connections window Fig 2 2 3 a to open Internet Properties window Fig 2 2 3 b E Network and Intern ctions File gdt Wew Favorites Tools Help ORIEN o Address D Network and Internet Connections Pick a task or pick a Control Panel icon EI internet options Network Connections D Click Fig 2 2 3 a Network and Internet Connections window Internet Properties P x L n a EE 4 General Securty Privacy Conte Connections Soifa Click i To set up an Internet connection click Setup Dial up and Virtual Private Network zeigen AT amp T Global Network Client 4 IRypnEnty cr nn N
11. stored in the projector and displayed on screen one by one 138 LWU420 User Manual Network Guide 020 000263 01 Rev 1 06 2010 CHAISTIE 2 Eq ipment connection and metWwonk setting 2 1 Required equipment preparation The following equipments are required to connect the projector to your PC through the network PC 1 equipped with the network feature 2 installed a web browser software 411 LAN cable CAT 5 or greater LWU420 User Manual Network Guide 4 020 000263 01 Rev 1 06 2010 CHAISTIE 2 2 Manual network connection setting 2 2 1 Equipments connection Connect the projector and PC with a LAN cable Before connecting with an existing network contact the network administrator Next please check the PC setting as explained below 2 2 2 Network settings This is the explanation of network connection settings for Windows XP and Internet Explorer 1 Log on to Windows XP as administrator authority 2 Open Control Panel from Start menu 3 Open Network and Internet Connections in Control Panel Fig 2 2 2 a Administrator authority is the account which can access to all functions k a Control PaneLicon 2 rtemet Exolrer FA Network agnostics EI wech options ws Network Connections Fig 2 2 2 a Network and Internet Connections window 4 Open Network Connections Fig 2 2 2 b EI Advanced Hep O pl Oen Bowe P DE e ioc
12. the frame lock RGB1 function on off Frame Lock RGB2 Turns the frame lock RGB2 function on off Frame Lock HDMI Turns the frame lock HDMI function on off RGB in 1 Selects the RGB1 input signal type RGB in 2 LWU420 User Manual Network Guide Selects the RGB2 input signal type 27 020 000263 01 Rev 1 06 2010 CHAISTIE 3 1 Configuring and controlling the projector via a web browser continued Item Description Setup Auto Keystone Execute Performs the automatic keystone distortion setting Keystone V Adjusts the vertical keystone distortion setting Keystone H Adjusts the horizontal keystone distortion setting Perfect Fit Adjusts the shape of the projected image in each of the corners Whisper Selects the whisper mode Mirror Selects the mirror status Monitor Out RGB1 Assigns the MONITOR OUT when the RGB1 input port is selected Monitor Out RGB2 Assigns the MONITOR OUT when the RGB2 input port is selected Monitor Out HDMI Assigns the MONITOR OUT when the HDMI input port is selected Monitor Out Component Assigns the MONITOR OUT when the COMPONENT input port is selected Monitor Out S Video Assigns the MONITOR OUT when the S VIDEO input port is selected Monitor Out Video Assigns the MONITOR OUT when the VIDEO input port is selected Monitor Out Standby Assigns the MONITOR OUT
13. 2010 CHAISTIE 3 4 Event Scheduling continued Schedule Settings 120 Schedule settings can be configured from a web browser Example If the IP address of the projector is set to 192 168 1 10 1 Enter http 192 168 1 10 into the address bar of the web browser 2 Enter the Administrator ID and password and click Logon 3 Click Schedule Settings on the main menu and select the required schedule item For example if you want to perform the command every Sunday please select Sunday Click Enable check box to enable scheduling Enter the date month day for specific date scheduling Click Apply button to save the settings After configure the time command and parameters click Register to add the new event 8 Click Delete button when you want to delete a schedule 4 5 6 7 There are three types of scheduling 1 Daily Perform the specified operation at a specified time every day 2 Sunday Saturday Perform the specified operation at the specified time on a specified day of the week 3 Specific date Perform the specified operation on the specified date and time NOTE In Standby mode the power indicator will flash green for approx 3 seconds when at least 1 Power ON schedule is saved e When the schedule function is used the power cord must be connected to the projector and the outlet and the power switch must be turned on The schedule function does not work when t
14. 7 Schedule Selg wi ccsdecssates vests a ennai 20 3 1 8 Date Time Settings 0 0 0 eee eter ee eitieee eee eeneeeeeeetieeeeeeennieeeeree 22 31 9 Security Settings EE 24 3 1 10 Projector Control 26 321 41 Projector Status vsinccccvevsndaenveiieasivnsnendvevtieaveeriidneindea inn 30 3 1 12 Network Restart 31 31213 Wee EE 31 3 2 E mail Alerte ea ceeeeee erence eee eeeeneeeeeeseeeeeeeeeeeneaeeeeteeeeeeeeeseeeaaeeeseeenanes 32 3 3 Projector Management using SNMP cc ceeceeeeeeeeeeeeeeeeeeeeeeeeeeeeeenaeeees 34 3 4 Event SCMECUINAG EE 35 3 5 MY IMAGE Still Image Transfer Display 38 3 6 Command Control via the Network eeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeteeeaeees 40 LWU420 User Manual Network Guide 020 000263 01 Rev 1 06 2010 CHAISTIE dle METI Une tons 1 1 Configuring and controlling via a web browser You can adjust or control the projector via a network from a web browser on a PC that is connected to the same network Logon the network from the web browser and it offers the menus to configure the network settings monitor the projector and so on Information Network Settings Port Settings Mail Settings SC Alert Settings schedule servings E Date Time Settings Security Settings Projector Control Projector Status Network Restart one ji EE Rie gt 1 2 MY IMAGE Still image Transfer Display Image files can be sent via the network and up to 4 image data can be
15. B B Fig 3 5 Still Image Transfer MY IMAGE transmission requires an exclusive application for your PC You can download it from the web site http www christiedigital com Refer to the manual for the application for instructions To display the transferred image select the MY IMAGE item in the NETWORK Menu For more information please see the description of the MY IMAGE item of the NETWORK Menu LQ NETWORK Menu in User s Manual detailed Operating Guide NOTE It is possible to allocate the image file up to 4 in the maximum e The image file also can be displayed by using schedule function from the web browser Refer to the item 3 4 Event Scheduling 135 in detail 38 LWU420 User Manual Network Guide 020 000263 01 Rev 1 06 2010 CHAISTIE 3 5 MY IMAGE Still Image Transfer Display continued Configure the following items from a web browser when MY IMAGE is used Example If the IP address of the projector is set to 192 168 1 10 1 Enter http 192 168 1 10 into the address bar Si the web browser 2 Enter the Administrator ID and password and 5 click Logon 3 Click Port Settings on the main menu 4 Click the Enable check box to open the Image Transfer Port Port 9716 Click the Enable check box for the Authentication setting when authentication is required otherwise clear the check box 5 Click the Apply button to save the settings When the authentication setting i
16. LWU420 a User Manual Network Guide 020 000263 01 CHRISTIE CHAISTIE Projector LWU420 User Manual Network Guide User s Manual detailed Network Guide Thank you for purchasing this projector This projector has the network function that brings you the following main features v Web control The projector can be controlled and monitored by a web browser software on your PC which can help you to setup and maintain the projector v MY IMAGE Still Image Transfer Display The projector can display still images that are transferred via the network This manual is only intended to explain Network function only For safety operations or any other issues refer to the Safety Guide and User s Manual concise and detailed NOTE The information in this manual is subject to change without notice e The manufacturer assumes no responsibility for any errors that may appear in this manual e The reproduction transfer or copy of all or any part of this document is not permitted without express written consent Trademark acknowledgment e Microsoft and Internet Explorer Windows Windows NT Windows Me Windows Vista are registered trademark of Microsoft Corporation e PowerPC is a registered trademark of International Business Machines Corporation e VESA and DDC are trademarks of the Video Electronics Standard Association e Apple and Macintosh Mac Mac OS are registered trademarks of Apple Inc e Pentium is a
17. There is a possibility that the interior portion has become overcooled Filter Error Filter time over Lamp Error Temp Error Cold Error Other error Other Error If displaying this error please contact your dealer Schedule Execution Error Lamp Time Alarm Lamp time over Alarm Time setting Filter Time Alarm Filter time over Alarm Time setting Transition Detector Transition Detector Alarm U2OPTION Menu in the User s Alarm Manual detailed Operating Guide The Power switch is turned on Off standby mode The SNMP access is detected from the invalid SNMP community Schedule Execution error 120 Cold Start Authentication Failure Refer to Troubleshooting in the User s Manual detailed Operating Guide for further detailed explanation of Error except Other Error and Schedule Execution Error 18 LWU420 User Manual Network Guide 020 000263 01 Rev 1 06 2010 CHAISTIE 3 1 Configuring and controlling the projector via a web browser continued The Alert Items are shown below Item Description Configures the time to alert Only Lamp Time Alarm and Filter Time Alarm SNMP Trap Click Enable check box to enable SNMP Trap alerts Click Enable check box to enable e mail alerts Except Cold Start and Authentication Failure Configures the subject line of the e mail to be sent The length of the subject line can be up to
18. a11bce1f7275813d4bde in front of the commands and send the data Send e3d97429adffa11bce1f7275813d4bde command 6 When the sending data is correct the command will be performed and the reply data will be returned Otherwise an authentication error will be returned NOTE As for the transmission of the second or subsequent commands the authentication data can be omitted when the same connection 44 LWU420 User Manual Network Guide 020 000263 01 Rev 1 06 2010
19. ays and configures schedule settings Description Daily Configures the daily schedule Sunday Configures the Sunday schedule Monday Configures the Monday schedule Tuesday Configures the Tuesday schedule Wednesday Configures the Wednesday schedule Thursday Configures the Thursday schedule Friday Configures the Friday schedule Saturday Configures the Saturday schedule Specific date No 1 Configures the specific date No 1 schedule Specific date No 2 Configures the specific date No 2 schedule Specific date No 3 Configures the specific date No 3 schedule Specific date No 4 Configures the specific date No 4 schedule Specific date No 5 Configures the specific date No 5 schedule 20 LWU420 User Manual Network Guide 020 000263 01 Rev 1 06 2010 CHAISTIE 3 1 Configuring and controlling the projector via a web browser continued The schedule settings are shown below Item Description Schedule Click Enable check box to enable the schedule Configures the month and date Date Month Day This item appears only when Specific date No 1 5 is selected Click Apply button to save the settings The current event settings are displayed on the schedule list To add additional functions and events set the following items Item Description Time Configures the time to execute commands Command Parameter Power Configures the param
20. differences between Administrator and User IDs Item Description Administrator Displays the projector s current y Network Information network configuration settings Displays and configures network d Network Settings settings Displays and configures Port Settings communication port settings Displays and configures e mail Mail Settings addressing settings Displays and configures failure amp Alert Settings warning alerts Displays and configures schedule Schedule Settings settings Displays and configures the date and Date Time Settings time settings Displays and configures passwords and other security settings Security Settings Projector Control Controls the projector Projector Status Displays the current projector status Restarts the projector s network Network Restart Sonnecton 12 LWU420 User Manual Network Guide 020 000263 01 Rev 1 06 2010 CHAISTIE 3 1 Configuring and controlling the projector via a web browser continued 3 1 1 Logon Refer to the following for configuring or controlling the projector via a web browser Example If the IP address of the projector is set to 192 168 1 10 1 Enter http 192 168 1 10 into the address EEE rd bar of the web browser and press Enter key or click 2 button The screen in Fig 3 1 1a will be displayed 2 Enter your ID and password and click Logon
21. e DNS server 192 168 1 50 Use the folowing DNS server addresses Prefered DNS server 255 255 255 0 L Advanced Fig 2 2 2 d Internet Protocol TCP IP Properties window 7 Set IP address subnet mask and default gateway for PC LWU420 User Manual Network Guide 020 000263 01 Rev 1 06 2010 CHAISTIE 2 2 Manual network connection setting continued About IP address Setting manually The Network address portion included in the IP address set into your PC should be common with projector s one And the entire IP address in the PC should not be overlapped with other equipments in the same network including the projector For example The projector s initial settings are as follows IP address 192 168 1 10 Subnet mask 255 255 255 0 Network address 192 168 1 in this case Therefore specify PC s IP address as follows IP address 192 168 1 xxx xxx shows decimal number Subnet mask 255 255 255 0 Network address 192 168 1 in this case Select from 1 to 254 for xxx not duplicating with any other equipments In this case projector has 192 168 1 10 IP address specify from 1 to 254 except 10 for PC NOTE 0 0 0 0 cannot be set to the IP address e The projector s IP address can be changed by using the configuration utility via a web browser 411 e If the projector and PC exist in the same network i e network address is common default
22. e MY IMAGE data 26 020 000263 01 Rev 1 06 2010 CHAISTIE 3 1 Configuring and controlling the projector via a web browser continued Item Description Picture Brightness Adjusts the brightness setting Contrast Adjusts the contrast setting Gamma Selects the gamma setting Color Temp Selects the color temperature setting Color Adjusts the color setting Tint Adjusts the tint setting Sharpness Adjusts the sharpness setting Active Iris Selects the active iris setting MyMemory Save Saves the MyMemory data MyMemory Recall Recalls the MyMemory data Image Aspect Selects the aspect setting Over Scan Adjusts the over scan setting V Position Adjusts the vertical position H Position Adjusts the horizontal position H Phase Adjusts the horizontal phase H Size Adjusts the horizontal size Auto Adjust Execute Performs the automatic adjustment Input Progressive Selects the progressive setting Video NR Selects the video noise reduction setting 3D YCS Selects the 3D YCS setting Color Space Selects the color space Component Selects the COMPONENT port setting C Video Format Selects the video format setting S Video Format Selects the s video format setting HDMI Selects the HDMI setting Frame Lock RGB1 Turns
23. er Example If the IP address of the projector is set to 192 168 1 10 1 Enter http 192 168 1 10 into the address bar of the web browser 2 Enter the Administrator ID and password and click Logon 3 Click Port Settings on the main menu 4 Click Enable check box to open the SMTP Port 5 Click Apply button to save the settings NOTE A Network Restart is required after the SMTP Port configuration settings have changed Click Network Restart and configure the following items 6 Click Mail Settings and configure each item Refer to the item 3 1 5 Mail Settings 417 for further information 7 Click Apply button to save the settings NOTE Click Send Test Mail button in Mail Settings to confirm that the e mail settings are correct The following mail will be delivered to the specified addresses Subject line Test Mail lt Projector name gt Text Send Test Mail IP Address lt Projector IP address gt MAC Address lt Projector MAC address gt 32 LWU420 User Manual Network Guide 020 000263 01 Rev 1 06 2010 CHAISTIE 3 2 E mail Alerts continued 8 Click Alert Settings on the main menu to configure the E mail Alerts settings 9 Select and configure each alert item Refer to the item 3 1 6 Alert Settings 418 for further information 10 Click Apply button to save the settings Failure Warning e mails are formatted as follows Subject line lt Mail title gt l
24. eters for power control Input Source Configures the parameters for input switching Configures the parameters for display of transfered image Display Image data 0438 Configures the commands to be executed Click Register button to add new commands to the schedule list Click Delete button to delete commands from the schedule list Click Reset button to delete all commands and reset the schedule settings from the schedule list NOTE After the projector is moved check the date and time set for the projector before configuring the schedules Strong shock may make the date and time settings 422 get out of tune 21 LWU420 User Manual Network Guide 020 000263 01 Rev 1 06 2010 CHAISTIE 3 1 Configuring and controlling the projector via a web browser continued 3 1 8 Date Time Settings Displays and configures the date and time settings Item Description Current Date Configures the current date in year month day format Current Time Configures the current time in hour minute second format Click ON check box to enable daylight savings time and set the following items Start Configures the date and time daylight savings time begins Month Configures the month daylight savings time begins 1 12 Configures the week of the month daylight savings time begins First 2 3 4 Last Configures the day of the week daylight savings time begins Sun Mon Tue Wed Th
25. ever dial a connection Dial whenever a network connection is not present O Always dial my default connection Current None Set Defaut J Local Area Network LAN settings LAN Settings do not apply to dial up connections Choose Settings above for dial up settings Fig 2 2 3 b Internet Properties window 2 Click Connections tab and then click LAN Settings button to open Local Area Network LAN settings Fig 2 2 3 c LWU420 User Manual Network Guide 8 020 000263 01 Rev 1 06 2010 CHAISTIE 2 2 Manual network connection setting continued Local Area Network LAN Settings Automatic configuration Automatic configuration may override manual settings To ensure the ise of manual settings disable automatic configuration le a proxy server for your LAN These settings will not apply to dp or YPN connections Addre Fig 2 2 3 c Local Area Network LAN Settings window 3 Uncheck all boxes in Local Area Network LAN Settings window Fig 2 2 3 c 2 2 4 Check connection Check PC and projector are connected properly here If it is not connected check cable connections and settings are properly or not 1 Start browser in PC and specify following URL then click 2 button URL http Projector IP address For example if projector IP address is 192 168 1 10 specify URL http 192 168 1 10 2 If Fig 2 2
26. he power switch is turned off O or the breaker in a room is tripped The power indicator will lights orange or green when the projector gets is receiving the power 36 LWU420 User Manual Network Guide 020 000263 01 Rev 1 06 2010 CHAISTIE 3 4 Event Scheduling continued Date Time Settings 122 The Date Time setting can be adjusted via a web browser Example If the IP address of the projector is set to 192 168 1 10 1 Enter http 192 168 1 10 into the address bar of the web browser Enter the Administrator ID and Password and click Logon 2 Click Date Time Settings on the main menu and configure each item Refer to the item 3 1 8 Data Time Settings for further information 3 Click Apply button to save the settings NOTE A Network Restart is required after the Daylight Savings Time or SNTP configuration settings have been changed e The battery for the built in clock may be dead if the clock loses time even when the date and time have been set correctly Replace the battery by following Internal clock battery section of the User s Manual concise e The internal clock s time may not remain accurate Using SNTP is recommended to maintain accurate time 37 LWU420 User Manual Network Guide 020 000263 01 Rev 1 06 2010 CHAISTIE 3 5 MY IMAGE Still Image Transfer Display The projector can display still images that are transferred via the network Display image data
27. in the standby mode dio Volume Adjusts the volume setting Treble Adjust the Treble setting Bass Adjusts the Bass setting Speaker Turns the built in speaker on off Audio RGB1 Assigns the AUDIO RGB1 input port Audio RGB2 Assigns the AUDIO RGB2 input port Audio HDMI Assigns the AUDIO HDMI input port Audio Component Assigns the AUDIO COMPONENT input port Audio S Video Assigns the AUDIO S VIDEO input port Audio Video Assigns the AUDIO VIDEO input port Audio Out Standby Assigns the AUDIO OUT in the standby mode HDMI Audio LWU420 User Manual Network Guide Selects the HDMI audio setting 28 020 000263 01 Rev 1 06 2010 CHAISTIE 3 1 Configuring and controlling the projector via a web browser continued Item Description Screen Language Menu Position V Menu Position H Blank Startup MyScreen Lock Message Template Option Auto Search Selects the language for the OSD Adjusts the vertical Menu position Adjusts the horizontal Menu position Selects the Blank mode Selects the startup screen mode Turns MyScreen lock function on off Turns the message function on off Selects the template setting Turns the automatic signal search function on off Turns the automatic keystone distortion correction function on off Turns the auto on function on off Configures the
28. is required for this port SNMP Port Configures the SNMP port Port open Click Enable check box to use SNMP Configures the destination of the SNMP Trap in IP format e The address allows not only IP address but also domain Trap address name if the valid DNS server is setup in the Network Settings The maximum length of host or domain name is up to 255 characters SMTP Port Configures the SMTP port Port open Click Enable check box to use the e mail function Click Apply button to save the settings NOTE The new configuration settings are activated after restarting the network connection When the configuration settings are changed you must Configures the image transfer port Port 9716 Authentication restart the network connection You can restart the network connection by clicking Network Restart on the main menu 16 LWU420 User Manual Network Guide 020 000263 01 Rev 1 06 2010 CHAISTIE 3 1 Configuring and controlling the projector via a web browser continued 3 1 5 Mail Settings Displays and configures e mail addressing settings Item Description Click Enable check box to use the e mail function Send mail Configure the conditions for sending e mail under the Alert Settings Configures the address of the mail server in IP format e The address allows not only IP address but also domain SMTP Server IP Address
29. layed when logged on using an Administrator ID Displays the network firmware version number This Firmware Version information is only displayed when logged on using an Administrator ID Firmware Date 14 LWU420 User Manual Network Guide 020 000263 01 Rev 1 06 2010 CHAISTIE 3 1 Configuring and controlling the projector via a web browser continued 3 1 3 Network Settings Displays and configures network settings Item Description IP Configuration Configures network settings DHCP ON Enables DHCP DHCP OFF Disables DHCP IP Address Configures the IP address when DHCP is disabled Subnet Mask Configures the subnet mask when DHCP is disabled Default Gateway Configures the default gateway when DHCP is disabled Configures the name of the projector The length of the Projector Name can be up to 64 Projector Name alphanumeric characters Only alphabets numbers and following symbols can be used amp lt gt A and space Configures the location to be referred to when using SNMP The length of the sysLocation can be up to 255 alphanumeric characters Only numbers 0 9 and alphabet az A Z can be used Configures the contact information to be referred to when using SNMP sysContact SNMP The length of the sysContact can be up to 255 alphanumeric characters Only numbers 0 9 and alphabet a z A Z can be
30. nity name on the screen that is displayed 7 Configure the settings for Trap transmission of Failures Warnings Click Alert Settings on the main menu and select the Failure Warning item to be configured 8 Click Enable check box to send out the SNMP trap for Failures Warnings Clear Enable check box when SNMP trap transmission is not required 9 Click Apply button to save the settings 34 LWU420 User Manual Network Guide 020 000263 01 Rev 1 06 2010 CHAISTIE 3 4 Event Scheduling The scheduling function enables to setup scheduled events including power on power off It enables to be self management projector NOTE You can schedule the following control events Power ON OFF Input Source and Transferred Image Display e The power on off event has the lowest priority among the all events that are defined at the same time e There are 3 types of Scheduling 1 daily 2 weekly 3 specific date 220 e The priority for scheduled events is as follows 1 specific date 2 weekly 3 daily e Up to five specific dates are available for scheduled events Priority is given to those with the lower numbers when more than one event has been scheduled for the same date and time e g Specific date No 1 has priority over Specific date No 2 and so on e Be sure to set the date and time before enabling scheduled events 22 LWU420 User Manual Network Guide 35 020 000263 01 Rev 1 06
31. on setting when authentication is required otherwise clear the check box 5 Click Enable check box to open Network Control Port2 Port 9715 to use TCP 9715 Click Enable check box for Authentication setting when authentication is required otherwise clear the check box 6 Click Apply button to save the settings 40 LWU420 User Manual Network Guide 020 000263 01 Rev 1 06 2010 CHAISTIE 3 6 Command Control via the Network continued When the authentication setting is enabled the following settings are required 024 7 Click Security Settings on the main menu 8 Click Network Control and enter the desired authentication password See NOTE 9 Click Apply button to save the settings NOTE The Authentication Password will be the same for Network Control Port Port 23 Network Control Port Port 9715 and Image Transfer Port Port 9716 e The new configuration settings are activated after restarting the network connection When the configuration settings are changed you must restart the network connection You can restart the network connection by clicking Network Restart on the main menu 41 LWU420 User Manual Network Guide 020 000263 01 Rev 1 06 2010 3 6 Command Control via the Network continued Command Format CHAISTIE Command formats differ among the different communication ports e TCP 23 You can use the RS 232C commands without any changes The reply data fo
32. rator Reenter the above password for verification Password er authority Configures the User ID and password Configures the User ID User ID The length of the text can be up to 32 alphanumeric characters Configures the User password User Password The length of the text can be up to 255 alphanumeric characters Re enter User Password Reenter the above password for verification 24 LWU420 User Manual Network Guide 020 000263 01 Rev 1 06 2010 CHAISTIE 3 1 Configuring and controlling the projector via a web browser continued Item Description Configures the Authentication password for the command control Authentication Configures the Authentication password The length of the Password text can be up to 32 alphanumeric characters Re enter Authentication Reenter the above password for verification Password SNMP Configures the community name if SNMP is used Configures the community name The length of the text can be up to 64 alphanumeric characters Network Control Community name Click Apply button to save the settings NOTE The new configuration settings are activated after restarting the network connection When the configuration settings are changed you must restart the network connection You can restart the network connection by clicking Network Restart on the main menu e Only numbers 0 9 and alphabet a z A Z can be used
33. registered trademark of Intel Corporation e JavaScript is a registered trademark of Sun Microsystems Inc e DVI is a trademark of Digital Display Working Group e HDMI the HDMI logo and High Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries All other trademarks are the properties of their respective owners 1 LWU420 User Manual Network Guide 020 000263 01 Rev 1 06 2010 CHAISTIE ae Content ccccceeeeeeeeeeeenseeeeeeeeeeeeeeeeneneseeeneeeeeeseseneneeeeeeeeseseeeeeeeeeeeeeen 2 1 Main functions sssessssnsonosossssnusennosnuononunennnunsononosonsnansnnososononnsansnunss 3 1 1 Configuring and controlling via a Web browse 3 1 2 MY IMAGE Still image Transfer Display 3 2 Equipment connection and network setting c0sssssssssseess 4 2 1 Required equipment preparation s sssri tsioan aaa aaa 4 2 2 Manual network Connection Setting 5 2 2 1 EQGuipmentS CONMECHON D 5 2 2 2 Ee le EE 5 2 2 9 Internet Ed BEE 8 2 2 4 Gieck COMME CUON 3 ig sna cevsdscedsevasvende OA 9 3 Management with Web browser software EE ERERER KE KREE REN 10 3 1 Configuring and controlling the projector via a web browser ee 11 JLI e LTE 13 3 1 2 Network Information 0 eee teeter een eee eeecneeeeeetineeeeeeetieeeeereea 14 31 3 Network SONGS erorcen A R R 15 3 1 4 El EE 16 3 51 25 Mail Settings iiccidsssetdeecestictes caves E EEE 17 Kl e EE 18 321
34. rmat is the same as the RS 232C commands However the following reply will be sent back in the event of authentication failure when authentication is enabled lt Reply in the event of an authentication error gt Reply Error code Ox1F 0x04 0x00 e TCP 9715 Send Data format The following formatting is added to the header 0x02 Data length 0x0D Checksum 1byte and Connection ID 1 byte of the RS 232C commands Header Data length RS 232C command Connection Check Sum ID 0x02 0x0D Header Data length RS 232C commands Check Sum Connection ID LWU420 User Manual Network Guide 13 bytes 0x02 Fixed 1 byte 1 byte RS 232C commands byte length 0x0D Fixed RS 232C commands that start with OxBE OxEF 13 bytes This is the value to make zero on the addition of the lower 8 bits from the header to the checksum Random value from 0 to 255 This value is attached to the reply data 42 020 000263 01 Rev 1 06 2010 CHAISTIE 3 6 Command Control via the Network continued Reply Data format The connection ID the data is same as the connection ID data on the sending data format is attached to the RS 232C commands reply data lt ACK reply gt Connection ID 1 byte lt NAK reply gt Connection 1 byte lt Error reply gt Connection ID 2 bytes 1 byte Error code lt Data reply gt Connection ID
35. s enabled the following settings are required 6 Click Security Settings on the main menu 7 Select Network Control and enter the desired authentication password 8 Click the Apply button to save the settings NOTE The Authentication Password will be the same for Network Control Port1 Port 23 Network Control Port Port 9715 and Image Transfer Port Port 9716 e The new configuration settings are activated after restarting the network connection When the configuration settings are changed you must restart the network connection You can restart the network connection by clicking Network Restart on the main menu 39 LWU420 User Manual Network Guide 020 000263 01 Rev 1 06 2010 CHRISTIE 3 6 Command Control via the Network You can configure and control the projector via the network using RS 232C commands Communication Port The following two ports are assigned for the command control TCP 23 TCP 9715 Command Control Settings 16 Configure the following items from a web browser when command control is used Example If the IP address of the projector is set to 192 168 1 10 1 Enter http 192 168 1 10 into the address bar of the web browser 2 Enter the Administrator ID and password and click Logon 3 Click Port Settings on the main menu 4 Click Enable check box to open Network Control Port1 Port 23 to use TCP 23 Click Enable check box for Authenticati
36. splays the current Blank on off status Mute Displays the current Mute on off status Freeze Displays the current Freeze status 30 LWU420 User Manual Network Guide 020 000263 01 Rev 1 06 2010 CHAISTIE 3 1 Configuring and controlling the projector via a web browser continued 3 1 12 Network Restart Restarts the projector s network connection Description Restarts the projector s network connection in order to activate new configuration settings NOTE Restarting requires you to re log on in order to further control or configure the projector via a web browser Wait 1 minute or more after clicking Restart button to log on again e The Logon menu 113 is displayed after restarting the projector s network connection if the DHCP is set to ON 3 1 13 Logoff When Logoff is clicked the Logon menu is displayed 113 31 LWU420 User Manual Network Guide 020 000263 01 Rev 1 06 2010 CHAISTIE 3 2 E mail Alerts The projector can automatically send an alert message to the specified e mail addresses when the projector detects a certain condition that is requiring maintenance or detected an error NOTE Up to five e mail addresses can be specified e The projector may be not able to send e mail if the projector suddenly loses power Mail Settings 17 To use the projector s e mail alert function please configure the following items through a web brows
37. t Projector name gt Text lt Mail text gt Date lt Failure Warning date gt Time lt Failure Warning time gt IP Address lt Projector IP address gt MAC Address lt Projector MAC address gt 33 LWU420 User Manual Network Guide 020 000263 01 Rev 1 06 2010 CHAISTIE 3 3 Projector Management using SNMP The SNMP Simple Network Management Protocol enables to manage the projector information which is a failure or warning status from the computer on the network The SNMP management software will be required on the computer to use this function NOTE It is recommended that SNMP functions be carried out by a network administrator e SNMP management software must be installed on the computer to monitor the projector via SNMP SNMP Settings 16 Configure the following items via a web browser to use SNMP Example If the IP address of the projector is set to 192 168 1 10 1 Enter http 192 168 1 10 into the address bar of the web browser 2 Enter the Administrator ID and Password and click Logon 3 Click Port Settings on the main menu 4 Click Enable check box to open the SNMP Port Set the IP address to send the SNMP trap to when a Failure Warning occurs NOTE A Network Restart is required after the SNMP Port configuration settings have been changed Click Network Restart and configure the following items 5 Click Security Settings on the main menu 6 Click SNMP and set the commu
38. timer to shut off the projector when no signal is detected Assigns the functions for the MY BUTTON button on the included remote control Assigns the functions for the MY BUTTON2 button on the included remote control Selects the My Source setting Auto Keystone Auto on Auto off My Button 1 My Button 2 My Source Remote Receiv Front Enable Disable remote receiv front Remote Receiv Rear Enable Disable remote receiv rear Remote Receiv Top Enable Disable remote receiv top Remote Freq Normal Enables Disables the remote control signal frequency normal Remote Freq High Enables Disables the remote control signal frequency high Closed Caption Display Selects Closed Caption DISPLAY setting Mode Selects Closed Caption MODE setting Channel LWU420 User Manual Network Guide Selects Closed Caption CHANNEL setting 29 020 000263 01 Rev 1 06 2010 CHAISTIE 3 1 Configuring and controlling the projector via a web browser continued 3 1 11 Projector Status Displays the current projector status Item Description Error Status Displays the current error status Lamp Time Displays the usage time for the current lamp Filter Time Displays the usage time for the current filter Power Status Displays the current power status Input Status Displays the current input signal source Blank On Off Di
39. u Fri Sat hour Configures the hour daylight savings time begins 0 23 minute Configures the minute daylight savings time begins 0 59 d Configures the date and time daylight savings time ends Configures the month daylight savings time ends 1 12 Configures the week of the month daylight savings time ends First 2 3 4 Last Configures the day of the week daylight savings time ends Sun Mon Tue Wed Thu Fri Sat hour Configures the hour daylight savings time ends 0 23 minute Configures the minute daylight savings time ends 0 59 Daylight Savings Time Week Day Time 22 LWU420 User Manual Network Guide 020 000263 01 Rev 1 06 2010 CHAISTIE 3 1 Configuring and controlling the projector via a web browser continued Item Description Configures the time difference Set the same time difference Time difference as the one set on your PC If unsure consult your IT manager Click the ON check box to retrieve Date and Time information from the SNTP server and set the following items SNTP Configures the SNTP server address in IP format e The address allows not only IP address but also domain name if the valid DNS server is setup in the Network Settings The maximum length of host or domain name is up to 255 characters SNTP Server IP Address Configures the interval at which to retrieve Date and Time
40. used DNS Server Address Configures the DNS server address sysLocation SNMP Click Apply button to save the settings NOTE The new configuration settings are activated after restarting the network connection When the configuration settings are changed you must restart the network connection You can restart the network connection by clicking Network Restart on the main menu e If you connect the projector to an existing network consult a network administrator before setting server addresses 15 LWU420 User Manual Network Guide 020 000263 01 Rev 1 06 2010 CHAISTIE 3 1 Configuring and controlling the projector via a web browser continued 3 1 4 Port Setting E Bak P a o 6 Network Restart Displays and configures com munication port settings Item Description Network Control Port1 Port 23 Port open Click Enable check box to use port 23 Configures command control port 1 Port 23 Click Enable check box when authentication is required for Authentication this port Network Control Port2 Port 9715 Port open Click Enable check box to use port 9715 Click Enable check box when authentication is required for this port Configures command control port 2 Port 9715 Authentication Image Transfer Port Port 9716 Port open Click the Enable check box to use port 9716 Click the Enable check box when authentication

Christie LWU420 User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents