RF users guide - AV
Contents
1. Troubleshooting I m pressing the advance button but the slides are not advancing 1 Check the cable connections 2 Verify that the LED on the remote comes on solid when the advance or reverse button is pushed and that the laser pointer is at full brightness when the laser button is pushed If not replace the battery 3 Verify that the transmitter has been trained to the receiver Follow the instructions under Training the Remote to the Receiver 4 If using USB verify that the correct operating system driver is loaded on your computer Try reloading the driver or try unplugging the receiver waiting 10 seconds and then plugging it back in 5 If using PS 2 try restarting the computer with the receiver plugged into the PS 2 port The LED on the remote flashes or does not turn on when push the advance or reverse button or the laser pointer is dim or does not work when the laser button is pushed 1 The battery is dead Replace the battery LASER RADIATION AVOID DIRECT EYE EXPOSURE DIODE LASER 5mW MAX OUTPUT AT 650NM CLASS IIIA LASER PRODUCT Limited Warranty Honeywell International Inc Seller 12800 Brook Printer Place Poway California 92064 warrants its prod specifications and to be free from defects in material and workmanship under normal use and service for 12 mon Seller s obligation shall be limited to repairing or replacing at its option free of charge for materials or labor wit2. with the manufacturer s instructions may cause interference to radio and television reception It has been type tested and found to comply with the limits for a Class B computing device in accordance with the specifications in Part 15 of FCC Rules which are designed to provide reasonable protection against such interference in a residential installation However there is no guarantee that interference will not occur in a particular installation If this equipment does cause interferences to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e lf using an indoor antenna have a quality ou door antenna installed e Reorient the receiving antenna until interference is reduced or eliminated e Move the receiver away from the control communicator e Move the antenna leads away from any wire runs to the control communicator e Plug the control communicator into a different outlet so that it and the If necessary the user should consult the dealer following booklets prepared by the Federal Communications Commission helpful Interference Handbook This booklet is available from the U S Governm receiver are on different branch circuits or an experienced radio television technician for additional suggestions The user or installer may find the ent Printing Office Wa
3. D USB Port 4 The computer should automatically recognize the receiver as a new hardware after about 5 to 15 seconds depending on the computer Follow the instructions for installing new hardware you may need to load the necessary USB driver from your operating system disk Once your computer has installed the receiver as new hardware it will not need to run through the same steps again Next time you plug the receiver into the same computer it will take about 5 to 10 seconds to recognize the receiver During the 5 to 10 seconds there may be little or no indication that the computer is communicating with the receiver Using a PS 2 connection Windows 95 98 NT 2000 XP or higher 1 Turn on your computer and let it fully boot up 2 Plug one end of the PS 2 cable into the PS 2 port on the receiver 3 Plug the other end of the PS 2 cable into the PS 2 keyboard port on your computer you may need to disconnect your keyboard first on desktop computers The computer should take about 5 to 15 seconds to recognize the receiver However depending on your system you may need to reboot o allow the computer to recognize the receiver Training the Remote to the Receiver The remote has been trained into the receiver at the factory The receiver can support up to 7 total remotes To train a new remote or re train an existing remote into the receiver 1 Press and release the program button on the receive
4. Honeywell POWER PRESENTER RF Part PPRF Instruction Manual The POWER PRESENTER RF remote is a handy compact presentation tool It allows you to control slides in any presentation or slide show software The POWER PRESENTER FF remote includes a built in laser pointer The kit includes a remote with laser pointer battery included a receiver a USB cable a PS 2 cable and a nylon carrying case The POWER PRESENTER RF uses radio frequency technology so there is no need to point the remote at the receiver to control your slides The maximum operating distance between the remote and the receiver is 150 feet depending upon operating environment System Requirements The only system requirements are USB or PS 2 compatibility The POWER PRESENTER RF is plug and play compatible with MAC OS 8 or higher and Windows 95 PS 2 only 98 NT 2000 XP or higher Connecting the Receiver to the Computer For maximum range the receiver should be placed as far away as possible from any electronic devices First determine if you will be using a USB connection or a PS 2 connection Do not try to connect both cables at the same time Using a USB connection MAC OS 8 or higher and Windows 98 NT 2000 or higher 1 Turn on your computer and let it fully boot up Program Button PS 2 Port 2 Plug one end of the USB cable into the USB port on the receiver 3 Plug the other end of the USB cable into the USB port ono on your computer LE
5. emote that you wish to match to that keystroke a For Power Point the normal commands are e Page Down Top Button e Page Up Middle Button e b blank screen Top and Middle Buttons pressed together b For Media Shout the normal commands are e F10 Top Button e F9 Middle Button e F6 blank screen Top and Middle Buttons pressed together 8 When a command is recognized the LED on the Base Receiver will flash and the scrolling text will pause The scrolling will continue until all three button command options top middle both are programmed 9 If you do not wish to use all three keystroke commands simply unplug your Base Receiver from the cable to stop the process 10 Close your text editing software application 11 Test your remote to confirm the commands you have selected Changing the Battery in the Remote 1 There are two alignment dots on the back of the remote case and one alignment dot on the battery cover Insert a quarter into the slot on the battery cover and turn counter clockwise until a aa the dot on the battery cover is lined up with the LEFT dot on the remote case The battery cover will release 2 Pull the battery out of the holder Dispose of the battery in an environmentally proper manner 3 Insert the new battery with the positive side facing you The 3 0 volt lithium battery number is CR2032 4 Make sure that the alignment dot on the battery cover is lined up
6. h Seller s specifications or proves defective in materials or workmanship under normal use and service Se Warranty or otherwise if the product is altered or improperly repaired or serviced by anyone other than Honeywel le uct to be in conformance with its own plans and ths from the date of original purchase any product that is proved not in compliance shall have no obligation under this Limited International Inc When returning a product a Return Material Authorization number RMA is required and must be obtained from Honeywell International Inc The RMA must be clearly displayed on the outside of the shipping carton and the product must be accompanied by doc provides proof of date of purchase FCC Statement um entation that explains the problem and This device complies with Part 15 of the FCC rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interferences that may cause undesired operation FCC ID Transmitter KFR LSRT Receiver KFR LSRR Federal Communications Commission FCC Part 15 Statement This equipment has been tested to FCC requirements and has been found acceptable for use The FCC requires the following statement for your informa y lon This equipment generates and uses radio frequency energy and if not installed and used properly that is in strict accordance
7. r The LED lights solid 2 Press the advance button the largest button on the remote three times On the third press the LED will turn off indicating the remote has been successfully trained Training the Remote to the Receiver Continued To delete all of the remotes from the receiver 1 Press and hold the program button on the receiver The LED will light for 3 seconds then go out 2 Release the program button Using the Remote EMITTED FROM THIS APERATURES After connecting the receiver properly simply start your presentation or slide show software put it in slide show mode and press the remote s larger advance button to advance the slides and the smaller reverse button to go back to the previous slide Press the smallest button to activate the laser pointer ADVANCE BUTTON REVERSE BUTTON LASER ACTIVATION BUTTON Changing the Remote Keystrokes 1 Turn on your computer and let it fully boot up 2 Plug the USB or PS 2 cable into the back of your computer 3 Plug the other end of the USB or PS 2 cable into the PS 2 port on the receiver 4 Launch a text editing software application i e MS Word 5 Open a blank document and display it on the front window of your monitor 6 On the back of the Base Receiver press the Program Button three 3 times 7 Keyboard commands will begin appearing on your open text window When the command required for your software appears press the button on your r
8. shington DC 20402 The user shall not make any changes or modifications to the equipment unless authorized by the installation instructions or User s Manual Unauthorized changes or modifications could void the user s authority to operate the equipment PPRFV1 10 04 Honeywell 12800 Brook Printer Place Poway California 92064 Copyright 2004 Honeywell International Inc 858 513 6391 Www powerremote com
9. with the LEFT alignment dot on the remote case as you replace the battery cover Then turn clockwise until the dot on the battery cover is lined up with the RIGHT dot on the remote case Battery Replacement It is recommended that you always carry a spare battery Product Specifications Transmitter e Range Up to 150 feet depending upon operating environment Dimensions 2 6 66mm L x 1 5 38mm W x 0 5 13mm H Weight 1 oz 24 g with batteries Radio Frequency 433 MHz Laser Diode Laser 5mW max output at 650NM Class Illa Power One 3 0 V CR2032 lithium battery Battery life 1 year under normal operation Receiver nterface PS 2 or USB port Dimensions 2 6 66mm L x 3 4 86mm W x 1 2 31mm H e Weight 2 oz 59g excluding cable Cables e 3ft USB cable A B e 3ft PS 2 cable male male General e Warranty 1 year limited e Compliance FCC part 15 Class B for U S Industry Canada RSS 210 FDA 21 CFR 1040 Laser Pointer Information Due to the potential of radiation exposure from the laser the Food and Drug Administration FDA requires that any user of this product report and return a defective unit to the manufacturer DO NOT point the laser light directly into the eye area or attempt to open or disassemble this product for any reason Tampering with the laser product may be hazardous and will automatically VOID the manufacturers warranty This product fully complies with FDA 21 CFR 1040 10 and 1040 11
Download Pdf Manuals
Related Search