2.4GHz WIRELESS A/V/ALARM RECEIVER USER MANUAL
Contents
1. ANT SMA connector for connected to 2 4 GHz antenna REMARK When the frequency channels have the interference adjust antenna or change the channel of transmitter and don t close to 802 11 a b g AP router and other 2 4GHz devices Note Please keep 3 5 meter awav 2 Caution for Installation 2 1 Be careful never let any water in this equipment 2 2 f necessary use a soft cloth moistened with alcohol to wipe off the dust 2 3 Be extra careful not to shake the unit 2 4 Avoid places where temperatures exceed 50 C or higher 2 5 Avoid places where there are frequent vibrations or shocks 2 6 When any abnormalities occur make sure to unplug the unit and contact your local dealer 3 Packing 3 1 Receiver x 3 2 Antenna x 3 3 User manual x 3 4 Screws x4 3 5 Plastic Conical Anchor x4 3 6 Power Adaptor x1 Option 4 Specification 2468 MHz POWER SUPPLY DC12V 500mA Adaptor CURRENT CONSUMPTION 250mA Typical VIDEO OUTPUT 1 Vp p Composite 75Q AUDIO OUTPUT ALARM OUTPUT NC NO COM Dry Contact Contact Rating AC 125V 0 5A DC 24V 1A DIMENSIONS without Antenna L 86 mm H 30mm JD 110 mm FCC Part 15 Notice This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate2. 2 4GHz WIRELESS A V ALARM RECEIVER USER MANUAL MODEL 1 Panel View 2 4G RX VIDED SCRAMBLE amp 1D LOGRES SING DC id i See j alan i F S a a z F 2i Geen EF hml e wach Pon POWER CISARM AUCO ANT EHHE api denkratiec STATE CH SELECT D ALARM a aut OUT OUT DC 12V IN Power input DC 12V 500mA 2 ALARM OUT Once triggered the built in buzzer and alarm remains on for a 20 sec time This port could be connected to alarm devices e g Siren Flashing Unit AUDIO RCA female for audio signal output VIDEO BNC female for video signal output POWER STATE LED Indicated to power on or ARM and RF link status l 0O Ae Power State LED High speed Flashing RF Loss Waiting TX Link Low Speed Flashing 6 DISARM DISARM at receiver side only 7 CH SELECT 1 2 3 4 2 4GHz receiver has two receiving modes one is single channel receiving and the other is scan mode for multi channel receiving In scan mode receiver shift to next channel per 3 seconds Note Alarm signal output is disabled when the receiver is operating in scan mode CHASMEL CH SE E27 SCAR KODE CH SELEST 7 EHR ae 8 ID AND ALARM MUTE ID address setting is use for paring with transmitters It must be make the same code setting to link transmitter and receiver each other The alarm mute function is use for muting built in buzzer and disables the alarm output at side only 1 9
3. radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help 1 This Transmitter must not be co located or operating in conjunction with any other antenna or transmitter 2 This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body 3 Any changes or modifications including the antennas made to this device that are not expressly approved by the manufacturer may void the user s authority to operate the equipment Q2009 12 04
Download Pdf Manuals
Related Search