TITAN 7600 STRINGING MACHINE USER`S MANUAL
Contents
1. 5 illustration A height adjustment knob es l Step 3 Unlock the turntable by loosening the brake illustration B brake 01 Step 4 Step 5 Insert two string clamps into the string Unlock the tension head by pushing clamp bases and four side supports the tension head by pushing the in the holes of the side support arms tension head locking lever back into catch Rotate the crank handle counter clockwise to slide the tension head to get closed to the racquet mount MOUNTING THE RACQUET FRAME 1 Loosen both mounting stocks by turning the mounting stock knobs counterclockwise Place the racquet properly on both mounting stocks Adjust the distance between the mounting stocks to accommodate the size of the racquet frame Turn both mounting stock knobs clockwise to lock both mounting stocks in place Do not apply excessive force or over tighten the mounting stock knobs this will damage the parts Check that the two swivel clamps can reach all the stringing area of the racquet frame 2 Lightly tighten center supports by turning the knobs on the outside of the center support clockwise 3 1 The side supports are adjustable to provide support to the racquet frame Open side support arms by turning four side support arm adjustment knobs counterclockwise Insert the four side supports onto the proper holes of the side support arms 3 2 Rotate the side support arm adjustment knobs cloc2. round adjustment of the string clamp counterclockwise to the correct tension by needle nose pliers or fingers adjusting directly 2 If gripper of the string clamp doesn t hold string well turn the round adjustment of the string clamp clockwise to the correct tension by needle nose pliers or fingers adjusting directly Needle Nose Pliers Adjustment Fingers Adjustment APPENDIX Adjust the Base of the Swivel Clamp to the Correct Holding Pressure Lift up the base handle and turn it counterclockwise Lower the handle and turn it clockwise Repeat the process until the base is locked in place The handle position could be at any desired position To adjust it lift up the base handle turn it to the desired position then lower the handle 9 4 11
3. TITAN 7600 STRINGING MACHINE USER S MANUAL Se gt Ff 2 fe 5 a 5 2 2 BPW Nel NON N N e e e Machine Body along Tension Head Assembly Floor Stand Swivel Clamp Swivel Clamp Holder K Shaped Side Support Side Support Arm Adjustment Knob Center Support Adjustment Knob Mounting Stock Turntable Mounting Stock Locking Knob Rubber Cover Shoulder of Mounting Stock Side Support Arm Turntable Rail Tension Head Rail Height Adjustment Knob Brake Tool Tray Reel Holder Column Base Foot String Gripper Tension Locking Lever Tension Head Cover Housing Tension Setting Knob Tension Head Handle Crank Stopper Display Power Button ASSEMBLY Step 1 Secure column to foot using 4 long bolts washers and nuts by a 6 mm and a 12 mm wrenches Mount the tool tray on the column with 4 small bolts by a 10 mm wrench Screw the string reel holder into the column Screw the height adjustment knob onto the column but not too deep Step 2 Insert the machine body into the 1 1 oa is column top and allow to set Adjust the machine body to the desired height and lock in place with the height adjustment knob 2
4. clockwise to decrease the tension until the desired tension appears on the display Step 2 Pulling the Strings To pull the string continue rotating the tension head crank handle backward until the tension locking lever clicks out This locks the tension head to the tension rail Step 3 Releasing the Strings To release the string after clamping hold on to tension head and push tension locking lever back up into the catch on the tension head Lift the string out of the string gripper for the next hole TENSION CALIBRATION Step 1 Set the tension scale on 60 Ibs Place a string attached to a tension calibrator in string gripper Tension calibrator will indicate the pounds of tension on tension head under actual stringing conditions Pull string until the locking lever releases If it releases before 60 165 or after 60 lbs the following adjustment is needed CAUTITION Be sure to release string holding tension calibrator You are now ready for adjustment Step 2 Loosen the safety screw A If the locking lever release before 60 lbs turn the adjustment screw B counterclockwise until the scale reading matches the calibrator s if the locking lever release after 60 lbs turn the adjustment screw B clockwise WARNING Be sure to tighten the safety screw A after the adjustment has been made APPENDIX Adjust String Clamp to the Correct Holding Pressure 1 If gripper of the string clamp is over tension turn the
5. kwise until the firm contact is made between the side supports and the racquet frame If the side supports can t contact the frame squarely when the arms are closed against the racquet please insert the side supports onto the other holes of the side support arms Apply a final adjustment to all racquet support points until the racquet is firmly secured in the mounting system KEYPAD OPERATING INSTRUCTIONS Step 1 Battery Setting Set one dry battery 9 volts beneath the tension head Caution position and correctly Step 2 Power Button To turn the machine on press the black POWER KG LB button for 1 second until a tension appears on the display NOTE the power save function has been set for 1 minute at factory before shipping so the display will shut down automatically after 1 minute To motivate the display repeat the procedure step 2 again To turn power off press the black POWER KG LB button for 2 seconds until OFF appears on the display Or wait for 1 minute till the power save function 1s motivated and display will shut down automatically as well Step 3 KG LB Button Press the black POWER KG LB button for 0 5 second to change tension display from KG to LB To set tension unit from LB to KG press the black POWER KG LB button for 0 5 second again TENSIONING Step 1 Setting Tension Set the tension by rotating the tension setting knob counter clockwise to increase the tension or
Download Pdf Manuals
Related Search