INSTRUCTION MANUAL REMOTE CONTROL SYSTEM 4
Contents
1. 3 Precautions for Safe 4 1 5 15 05 6 4 beste a E ee de eed ecw ead 5 PRECAUTIONS 2 toa eth Eve eet ete ote de abe Avett 6 Nomenclature and 5 8 Remote Controller RC 4R 2 teen eee 8 Remote Controller Handle Unit RC 4H 0 000002 eee 10 ween Arete E RAAE we awe eee eye we 11 Battery Installation and Replacement 11 Installing RC 4R onto the Prism Unit 7 4 12 Communication between the RC 4R and a Data 13 Mounting Remote Controller Handle Unit RC 4H onto the TS IS QS 13 Basic Operation lt i sist kidea Se Sore ead wes 14 Power Switch ON eie 90h Ss Se bans eh ae eae Pace eae ee eae ee de es 14 Battery Remaining Display 14 Battery Warning Display for RC 4R 1 eens 14 Battery Warning for TS IS QS 14 Auto Power Off ee re ae Sete Pa aie eee 14 Error Display a eee ee BPEL ees teed 14 Setting for Communications with 5 15 Light Emitting Angle soi eee tebe eae eye Peed bb De et 16 Light Detecting Range2. When using with the prism unit A7R4 A7PR4 The operating distance may be shorter than normal in such the condition is not good by the heat simmer or strong direct sun shine to the detector Approximately 10 seconds 2 3 Sight haze with visibility about 20km 12 5 miles moderate sunlight with light shimmer Under normal weather conditions with the telescope turned 90 relative to the prism and turn round performed with the prism roughly aligned vertical Refer to Refer ence Turn round motions on page 19 6 20 DC 7 4V from TS IS QS Horizontal 360 Vertical 30 0 3 kg 58 D x 166 W x 71 H mm 0 4 kg with battery 126 D x 124 W x 67 H mm with antenna folded down Bluetooth Specification v1 2 Generic Access Profile Service Discovery Application Profile Serial Port Profile IEEE std802 48bit LAN MAC Address 010518 Output Class2 About 5m The range will be different by a condition 28 SS Wireless Unit Communication distance Transmission output Transmission method Emitting Laser Angle of Laser Laser class Detecting Laser Detecting range Interface Connector with 6 pins Rechargeable Battery BT 66Q Output voltage Capacity Maximum operating time 1 Normal use Input voltage Frequency Recharging time at 20 C 68 F Battery BT 66Q Operating temperature Charging signal Finishing signal Weight with AC DC converter Specifications A
3. Setting Mode Communication Baud Rate Setting can be done with the dip switch on the battery section 1 Remove battery cover and battery 2 Set the dip switch with a pin Battery cover lug Battery cover Dip switch Dip switch Setting Contents OFF default 38400 bps ___ Serial signal RS 232C 1 O baud rate setting ON 9600 bps NN Unused fixed to OFF Unused fixed to OFF s unused fixed to OFF Unused fixed to OFF A unused fixed to OFF Unused fixed to OFF Dip switch No 2 4 must be fixed to OFF position The RC 4R does not work correctly when the switch No 2 4 are set to ON position 21 Power Source and Charging Power Source and Charging AD 14 AC cable To charge 1 Connect the AC DC converter AD 14 and AC Cable to the charger 1 2 Plug the AC Plug into the outlet The POWER LED will light 3 Attach the battery the charger Charging will start The CHARGE LED will light up orange Charging will take approximately 3 hours per battery The CHARGE LED will light up in green If two batteries are attached to the charger it will take approximately 6 hours to charge them completely If battery power is at a very low level when beginning charging such as after the instrument has been in storage over an extended period of time in a discharge state a full charge may not be possible with a sin
4. snes e pa E A a DEE eee eee 17 Turn round Function e aeeiio erne e E E DE e E a e e ae 18 Stopping Turn round operations 19 Low Power Mode of Laser 19 Reference Turn round motions 0 00 cece eee 19 Setting Mode iia si a eee a ae bt 20 Setting MEMS henee anie lhcb Basi aa ata DAG AD wae Saas 20 How to Channel Sets cg ven a ee tee ua a De eae 20 Communication Baud Rate 0 EA 21 Power Source and Charging 22 cna ieee Ge eG eee iets 24 Regulations ecseri wie want aa EN 25 vecsi eena ede ke led we we ee ee bw Be ae ae 28 Foreword Standard Package Components The numerical value in parentheses shows the quantity RC 4H 1 RC AR 1 1 1 Moy Battery BT 66Q 1 Battery charger BC 30D 1 AC DC Converter AD 14 1 AC Cable 1 Silicon cloth 1 Make sure that all of the above items are with the instrument when purchased Precautions for Safe Operation Precautions for Safe Operation For the safe use of the product and prevention of injury to
5. does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help This transmitter must not be co located or operated in conjunction with any other antenna or transmitter This equipment complies with FCC radiation exposure limits set forth for uncontrolled equipment and meets the FCC radio frequency RF Exposure Guidelines in Supplement C to OET65 This equipment has very low levels of RF energy that is deemed to comply without maximum permissive exposure evaluation MPE But it is desirable that it should be installed and operated with at least 20cm and more between the radiator and person s body excluding extremities hands wrists feet and ankles Declaration of Conformity Model Number RC 4R Trade Name TOPCON CORPORATION Manufacturer Name TOPCON CORPORATION Address 75 1 Hasunuma cho Itabashi ku Tokyo 174 8580 JAPAN Country JAPAN U S A Representative Responsible party TOPCON POSITIONING SYSTEMS INC Address 7400 National Drive Livermore CA94551 U S A Telephone numbe
6. operators and other persons as well as prevention of property damage items which should be observed are indicated by an exclamation point within a triangle used with WARNING and CAUTION statements in this instruction manual The definitions of the indications are listed below Be sure you understand them before reading the manual s main text Definition of Indication A Ignoring this indication and making an operation error could possibly result in WARNING death or serious injury to the operator Ignoring this indication and making an operation error could possibly result in A CAUTION personal injury or property damage A General This symbol indicates items for which caution hazard warnings inclusive is urged Specific details are printed in or near the symbol This symbol indicates items which are prohibited Specific details are printed in or near the symbol This symbol indicates items which must always be performed Specific details are printed in or near the symbol A Warning S Do not perform disassembly or rebuilding Fire electric shock or burns could result Do not use the unit in areas exposed to high amounts of dust or ash in areas where there is inadequate ventilation or near combustible materials An explosion could occur Risk of injury by falling down the instrument or case Do not use a carrying case with a damaged which belts grips or latches It could be dangerous if the instrument
7. to EU members states only Following information is only for EU member states The use of the symbol indicates that this product may not be treated as household waste By ensuring this product is disposed of correctly you EU WEEE will help prevent potential negative consequences for the environment Directive and human health which could otherwise be caused by inappropriate waste handling of this product For more detailed information about the take back and recycling of this product please contact your supplier where you purchased the product or consult TOPCON CORPORATION EU EU Battery Directive EU EU Battery This symbol is applicable to EU members states only Directive Battery users must not dispose of batteries as unsorted general waste but treat properly 25 Regulations Region Country Directives Regulations Labels Declarations U S A FCC Class B NOTE This equipment has been tested and found to comply with limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment
8. 4S TOPCON INSTRUCTION MANUAL REMOTE CONTROL SYSTEM 4 RC 4 22210 90081 Foreword Foreword Thank you for purchasing the TOPCON RC 4 Remote control system 4 For the best performance of the instrument please read these brief instructions carefully and keep them in a convenient location for future reference This system has the following features Enables wireless communications between a built in wireless total station TS 9 series imaging station IS Quick station QS hereafter referred as TS IS QS and an RC 4R on the prism side which allows one man survey with the use of a data collector Has the turn round function with which more efficient one man survey is possible Turn round motions Refer to Light Emitting Angle on page 16 and Light Detecting Range on page 17 RC 4R should be kept aiming so that the TS IS QS always stays within the above range of laser beam emission until the turn round motions are completed If the aiming is out of above range while RC 4R is in turn round motions the turn round could not be completed gt Trademark Bluetooth Bluetooth is a registered trademark of Bluetooth SIG Inc U S A Foreword Contents Foreword ata te fae Sete hase enters 1 GONMTENIS acl ae fe Race Stal Sith E Meee 2 Standard Package Components
9. A BRH 21 CFR 1040 or Radiation Safety of Laser Products Equipment Classification Requirements and User s Guide IEC Publication 60825 1 provided on the safety standards for laser beam As per the said standard this product is classified as Class 1 1 Laser Products This is simple a product to operating that is not required to training from a Laser safety officer In case of any failure do not disassemble the instrument Contact TOPCON or your TOPCON dealer Class 1 Laser Product Invisible Laser Beam TS IS QS series The software must be of the correct version for your version of the TS IS QS series otherwise the RC 4 will not function properly Contact TOPCON or your TOPCON dealer for version information 5 Precautions Precautions Before starting work or operation be sure to check that the instrument is functioning correctly with normal performance Battery level check Confirm battery remaining level before operating Direct sunlight Do not leave the instrument under strong sunlight for a long time It may cause the instrument to malfunction Guarding the instrument against shocks When transporting the instrument provide some protection to minimize the risk of shocks Heavy shocks may cause the measurement to be faulty Waterproof property The instrument can not be submerged underwater RC 4 is designed based on the International Standard IP65 and RC 4H is designed based on the Internation
10. Functions Turn round key Channel key Escape key Key Function Power switch ON OFF of power of the RC 4R Turn round key TS IS QS will be in turn round motion Cancels the emitting laser for turn round motion The TS IS QS will stop the Escape key turn round operation after continuing the motion for a while Channalke Changes the transmission channels Emitting laser for turn round motion SS Wireless LEDs LED Status Contents Power On solid The power of RC 4R is ON LED Flash The battery remaining of RC 4R is low The battery should be recharged or replaced with a fully charged battery Off The power is OFF Receiving On solid LED RC 4R is in the middle of data reception Sending On solid LED RC AR is in the middle of data transmission Flash RC AR is in the middle of turn round command transmission Nomenclature and Functions Remote Controller Handle Unit RC 4H Attaching the RC 4H to the TS IS QS it enables the TS IS QS to do turn round motions Detectors at five points Connection points Sa N Do not damage or shock connection points It may cause malfunction 10 Preparation Preparation Battery Installation and Replacement 1 Push down the battery cover lug to unhook it and remove the cover 2 Insert Battery BT 66Q in the direction matching connection points as shown the illust
11. LED Power switch Battery Remaining Display Push ESC key and the battery remaining capacity will be displayed for approximately 5 seconds Battery remaining display OPOWER Battery Warning Display for RC 4R When the battery of the RC 4R is low the power LED will flash with beep sound Audio sound Two pitches frequent beep synchronized with power LED Confirm the battery remaining when turning on the instrument When the power LED is flashed with beep sound replace or recharge the battery Battery Warning for TS IS QS series When the battery power of TS IS QS in communication with RC 4R is low the beep will sound from the RC 4R Audio sound Three pitches frequent beep When the beep sounds replace or recharge the batteries of TS IS QS Auto Power Off If no key operation is given or no communication is performed for more than 30 minutes the power turns off automatically Error Display The RC 4R unit does not display errors Refer to the operation manual for the data collector and other software for details 14 Basic Operation Setting for Communications with TS IS QS The following settings is prerequisites for the communications to take place between the TS IS QS or an application program and RC 4R The same RC channel SS Wireless channel must be assigned to both RC 4R the TS IS QS With RC and SS Wireless channels for the RC 4R the parameters of t
12. al Standard IP54 therefore it is protected from the normal rainfall Storing the instrument for long period Remove the battery from the instrument when you would not use it for long period Maintenance Always clean the instrument after use If the instrument becomes wet from rain dry moisture clean the instrument dust off well and then wipe clean with a soft cloth Remove the dust using a brush then wipe off with a soft cloth For cleaning the lens surface of the receiving window use a cleaning brush then use a clean lintless cotton cloth Moisten it with alcohol or mixture with ether to wipe gently in a rotational motion from the center out To remove the dust the surface of emitting window or the parts made by plastic never use thinner benzine Use a clean cloth moistened with neutral detergent User e This product is for professional use only The user is required to be a qualified surveyor or have a good knowledge of surveying in order to understand the user and safety instructions before operating inspecting or adjusting Wear the required protectors safety shoes helmet etc when operating Exceptions from Responsibility The user of this product is expected to follow all operating instructions and make periodic checks of the product s performance The manufacturer or its representatives assumes no responsibility for results of a faulty or intentional usage or misu
13. bout 1000m The range will be different by a condition 100mW or less DS FH hybrid SS method Each direction 10 At greater distances the laser light at the edge of the emit ting range angle will be weaker by laser emitting charac teristic 100m 328ft Approximately 10 400m 1310ft Approximately 4 The range and angle will be different by a condition Class 1 Class Horizontal 35 Vertical 35 RS 232C Baudrate 38400 9600 Default 38400 Bit length 8 bits Parity bit None Stop bit 1 bit DC7 4V 2500mAh 9 hours 1 Under normal temperature at 20 C Measuring two points Including communicating and recording data every 1 minute and using turn round function once every 10 min utes In low temperature operating time will decrease rapidly due to the characteristic of battery Battery Charger BC 30D with AC DC converter AD 14 and AC cable AC 100 240V 50 60Hz 3 hours 1 battery 10 C to 40 C 50 F to 104 F Orange charge lamp should glow Green charge lamp should glow 0 4kg 0 8 Ibs 29 This is the mark of the Japan Surveying Instruments JSIMA Manufacturers Association 2010 TOPCON CORPORATION ALL RIGHTS RESERVED TOPCON CORPORATION 75 1 Hasunuma cho Tokyo 174 8580 Japan http www topcon co jp Please see the attached address list or the following website for contact addresses GLOBAL GATEWAY hitp global topcon com
14. cally track RC 4R prism Turn round function is useful for auto tracking when you start working or when the auto tracking is interrupted by any reason For increasing efficiency keep the auto tracking status when you move to another measurement point The settings and conditions of communication are prerequisites for the communications to take place between the TS IS QS and RC 4R 1 Turn on the TS IS QS and execute the External Link 2 the RC 4R by pressing the power switch 3 Collimate the TS IS QS by using the sighting collimator on the RC 4R 4 Press the turn round on the RC 4R TS IS QS starts searching and ends in the tracking mode TS IS QS must be kept apart from reflecting planes such as glass and white walls Reflected light may prevent it from correct prism searching and from auto tracking In this case change the power mode of RC 4R to the low power mode to decrease the output of laser beam To change the power mode refer to Low Power Mode of Laser Beam on page 19 18 Basic Operation Turn round operation status display With the RC 4R turn round operation will be displayed as shown below Searching Ready for communication Low Power mode OPOWER Stopping Turn round operations Press the ESC key to terminate turn round operation After the key is pressed turn round operation will continue for a short time bef
15. d IEC non industrial type configuration Do not use batteries or the battery charger if wet Resultant shorting could lead to fire or burns Do not connect or disconnect power supply plugs with wet hands Electric shock could result Do not use batteries other than those designated An explosion could occur or abnormal heat generated leading to fire Caution Do not touch liquid leaking from batteries Harmful chemicals could cause burns or blisters OOO Bluetooth wireless technology Warning Do not use within the vicinity of hospitals Malfunction of medical equipment could result Use the instrument at a distance of at least 22 cm from anyone with a cardiac pacemaker Otherwise the pacemaker may be adversely affected by the electromagnetic waves produced and cease to operate as normal Do not use onboard aircraft The aircraft instrumentation may malfunction as a result Do not use within the vicinity of automatic doors fire alarms and other devices with automatic controls as the electromagnetic waves produced may adversely affect operation resulting in an accident OO SOP Laser safety A Warning Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure This product uses the invisible laser beam to communicate This product is manufactured and sold in accordance with Performance Standards for Light Emitting Products FD
16. falls over please check that you fix the handle to the instrument Power Supply OOO OOP Warning Do not short circuit Heat or ignition could result Do not use voltage other than the specified power supply voltage Fire or electrical shock could result Do not use damaged power cords plugs or loose outlets Fire or electric shock could result Do not use power cords other than those designated Fire could result Do not place articles such as clothing on the battery charger while charging batteries Sparks could be induced leading to fire Use only the specified battery charger to recharge batteries Other chargers may be of different voltage rating or polarity causing sparking which could lead to fire or burns Do not heat or throw batteries into fire An explosion could occur resulting in injury Precautions for Safe Operation Do not use the battery or charger for any other equipment or purpose Fire or burns caused by ignition could result To prevent shorting of the battery in storage apply insulating tape or equivalent to the terminals Otherwise shorting could occur resulting in fire or burns To reduce the risk of hazards use only CSA UL certified power supply cord set cord is Type SPT 2 or heavier minimum No 18 AWG copper one end is provided with a moulded on male attachment plug cap with a specified NEMA configuration and the other end is provided with a moulded on female connector body with a specifie
17. gle charging In such a case recharge a second time 4 After charging remove the battery from the charger Remove the AC Plug from the outlet The POWER LED Red ON Power is on The CHARGE LED will indicate charging status OFF Wait for charging Orange ON Charging Green ON Charging completed Orange Flashing Charging error CHARGE LED will flash when the battery life is over or the battery is broken down Replace the battery to new one 1 Always use the AC DC converter provided with the product 22 Power Source and Charging Do not charge continuously otherwise the battery and the charger may be deteriorated If charging is necessary use the charger after stopping charge for approximately 30 minutes Do not charge the battery in right after the battery is charged it causes deterioration of the battery in rare cases The charger may develop heat while charging there is no problem of it Note Recharging should take place a room with an ambient temperature range of 10 to 40 C 50 F to 104 F If charging is done at high temperature charging time of the battery may take longer Exceeding the specified charging time may shorten the life of the battery and should be avoided if possible The battery will self discharge when stored and should be checked before using with instrument If the battery is not used over an extended period of time store in place at 30 C or bel
18. he application software used for the FC 250 or PC may be prioritized For further details please refer to the instruction manual for your application software Setting Parameters in TS IS QS Refer to the TS IS QS instruction manual for the TS IS QS setup procedures Setting Parameters in RC 4R Set the parameters in Setting Mode Refer to Table of item to be set in Setting Mode Setting Parameters of Bluetooth Communication port in Data Collector When connecting the RC 4R and data collector using Bluetooth there are no settings for the RC 4R Details about procedures for connecting the data collector and RC 4R by Bluetooth refer to the instruction manual for the application software used on the data collector Setting Parameters of Communication port in Data Collector Connect a data collector to be used to the serial RS 232C connector of the RC 4R and set the items as follows B Rate 38400 Data L 8 Parity none Stop Bit 1 Refer to the instruction manual for the application software used on the data collector for the setup procedures 15 Basic Operation Light Emitting Angle Laser beams are emitted from the emitting window of the RC 4R The angle of emitting laser beams is as follows Light emitting angle Top view At greater distances the laser light at the edge of the beam field angle will be weaker RC 4R should be kept aiming s
19. he metal terminals on the individual batteries must be covered with tape to prevent short circuiting and heat buildup or batteries can be placed in individual plastic bag Battery packs should not be dissembled prior to return Topcon customers are responsible for complying with all federal state and local regulations pertaining to packing labeling and shipping of batteries Packages must include a completed return address be prepaid by the shipper and travel by surface mode Under no circumstance should used recyclable batteries by shipped by air Failure to comply with the above requirements will result in the rejection of the package at the shipper s expense Please remit packages to Topcon Positioning Systems Inc C O Battery Return Dept 150 7400 National Dr Livermore CA 94551 DON T THROW AWAY RECHARGEABLE BATTERIES RECYCLE THEM Canada ICES Class B This class B digital apparatus meets all requirements of the Canadian interference Causing Equipment Regulations Cet appareil num rique de la class B respecte toutes les exigences du R glement sur le mat rique brouilleur du Canada This Class B digital apparatus complies with Canadian ICES 003 Cet appareil numerique de la Class B est conforme a la norme NMB 003 du Canada Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause u
20. ndesired operation of this device This equipment complies with IC radiation exposure limits set forth for uncontrolled equipment and meets RSS 102 of the IC radio frequency RF Exposure rules This equipment has very low levels of RF energy that is deemed to comply without maximum permissive exposure evaluation MPE But it is desirable that it should be installed and operated with at least 20cm and more between the radiator and person s body excluding extremities hands wrists feet and ankles Australia C Tick The compliance label indicates that the product complies with the applicable standard and establishes a traceable link between the equipment and the manufacturer importer or their agent responsible for compliance and for placing it on the Australian market 27 Specifications Operating temperature Storing temperature Protection against water and dust Turn round operating distance 1 1 Turn round operating time Number of RC channels Number of SS WIRELES channels Remote Controller Handle Unit RC 4H Power source Detective range Weight Dimensions Remote Controller RC 4R Weight Dimensions Bluetooth Unit Bluetooth Standard Bluetooth profiles BD Address QDID Bluetooth Transmitting Bluetooth Communication distance Specifications 20 C to 50 C 30 C to 60 C RC 4R IP65 RC 4H IP54 Based on the standard IEC60529 5m 400 m 16ft 1310 ft
21. nditions the time required for communications can increase to the point that turn round operations require a long time to complete and under certain circumstances such operations might not even be completed properly The following conditions can adversely affect operation When units are used for communication over long distances or under poor atmospheric and weather conditions e g in strong direct sunlight heat refraction such as occurs near road surfaces and building surfaces on hot days rain fog etc When the aim of the RC 4R is set incorrectly refer to Light Emitting Angle on page 16 When communication channel settings or other settings of the TS IS QS and RC 4R are not matched or are set incorrectly refer to Setting Mode on page 20 When the TS IS QS is located in front of or to the side of glass or some other reflective surface When during turn round operations a person car or other object obstructs the light path between the TS IS QS and the RC 4R When the units are used over long distances the RC 4R is set to low power mode refer to Low Power Mode of Laser Beam on page 19 When the dip switch settings on the RC 4R are set incorrectly refer to Communication Baud Rate on page 21 When the battery status display on the TS IS QS is flashing low battery power 19 Setting Mode In this mode following items can be set Setting Items Selecting item Setting Mode Description RC chan
22. nel 1 to 6 CH Sets a channel to be used for turn round The same communication channel 1to 6 must be assigned to both RC 4R and the TS IS QS Prevents interference of communication when several systems consisting of a TS IS QS and a RC 4 are used at one site SS Wireless channel 01 to 20 CH Sets a channel to be used for communications The same communication channel 01 to 20 must be assigned to both RC 4R and the TS IS QS Prevents interference of communication when several systems consisting of a TS IS QS and a RC 4 are used at one site Communication baud rate 38400 9600 bps How to Channel Set The communication baud rate can be selected RC channel SS Wireless channel 1 With the power ON push the channel change key on the panel once Current RC channel will be displayed Default setting 1 CH 2 While the RC channel is displayed approx 3 seconds push the key once again It will switch to the next RC channel 3 Repeat step 2 until the RC channel you wish to set is displayed After approx 3 seconds the current SS Wireless channel will be displayed in 2 digits Default setting 01 CH 4 While the SS Wireless channel is displayed approx 3 seconds push the key once again It will switch to the next SS Wireless channel 5 Repeat step 4 until the SS Wireless channel you wish to set is displayed The communication channel setting cannot be changed during turn round 20
23. o that the TS IS QS always stays within the above range of laser beam emission until the turn round motions are Important completed If the aiming is out of above range while RC 4R is in turn round motions the turn round could not be completed 16 Basic Operation Light Detecting Range The detecting angles of RC 4R and RC 4H TS IS QS are shown below TS IS QS can only be turned round with the turn round key under the condition that RC 4R remains confined within the range as shown below where RC 4H can detect light Top view Detecting range 00000000 Maintain the angle toward the TS IS QS within the range shown above until Important the turn round function is completed Detecting range RC 4H can detect the laser in all horizontal direction Turn round function can be done within above range 17 Basic Operation Turn round Function Do not change the RC 4R direction during turn round motions When the direction is changed the detecting signal for TS IS QS moves and the prism search cannot be performed correctly causing a delay in the time required to complete the search or preventing the search from being completed At greater distances the laser light at the edge of the emitting range angle will be weaker therefore the RC 4R must be aimed correctly Important The turn round key on RC 4R is used to have the TS IS QS search or automati
24. ore the TS IS QS comes to a stop Low Power Mode of Laser Beam When the TS IS QS performs a turn round function at a distance of approximately 30 m from the RC 4R strong reflections of the pulsed laser diode PLD emission can prevent the TS IS QS from searching the prism correctly In this case switch the laser to low power mode to reduce the intensity of such reflections In low power mode the range of the turn round function is shorter than in normal power mode Approx 50m To change the low power mode Turn the power ON while holding down the ESC key A buzzer will sound indicating that the RC 4R is in low power mode To return to normal power mode turn the power OFF wait several seconds and then turn the power ON again Reference Turn round motions When the turn round key on the RC 4R is pressed the pulsed laser diode PLD in the emitter produces a laser beam with a 10 cone pattern refer to Light Emitting Angle on page 16 The RC 4H component of the TS IS QS has photo detectors on all four sides front rear right and left allowing laser beams to be detected in any orientation This detection ability extends to approximately 30 in the vertical direction refer to Light Detecting Range on page 17 Upon detecting laser emissions the TS IS QS aligns toward the RC 4R After horizontal alignment the telescope is scanned vertically in order to target the prism and initiate auto tracking Under certain co
25. ow in a 50 charged state Over discharge will lower performance and a full charge may become impossible Please charge once every few months 23 Special Accessories Special Accessories Data Collector Prism unit A7R4 Suitable for systemization of measuring instrument Measuring data will be automatically stored and transferred to a computer system making measuring operations more efficient and saving time and effort in such operation 24 Regulations Regulations Region Directiv s Labels Declarations Country Regulations Applicable EMC NOTICE instrument C In industrial locations or in proximity to RC 4H industrial power installations this instrument EU RC 4R might be affected by electromagnetic noise Under such conditions please test the instrument performance before use EMC Class B R amp TTE Directive REMOTE CONTROLLER RC 4R Hereby TOPCON CORP declares that the above mentioned equipment is in compliance with the essential requirements and other relevant provisions of Applicable Directive 1999 5 instrument EU RC 4R Please inquire below if you wish to receive a copy of Topcon s Declaration of Conformity R amp TTE Class 1 Topcon Europe Positioning B V Essebaan 11 2908 LJ Capelle a d IJssel The Netherlands Tel 31 10 4585077 Fax 31 10 2844949 http www topcon positioning eu index asp WEEE Directive This symbol is applicable
26. r 925 245 8300 California U S A Proposition65 WARNING Handling the cord on this product or cords associated with accessories sold with this product will expose you to lead a chemical known to the State of California to cause birth defects or other reproductive harm Wash hands after handling California U S A Perchlorate Material CR Lithium Battery This product contains a CR Lithium Battery which contains Perchlorate Material special handling may apply See http www dtsc ca gov hazardouswaste perchlorate Note This is applicable to California U S A only 26 Regulations Region Country Directives Regulations Labels Declarations California and NY U S A Recycling Batteries DON T THROW AWAY RECHARGEABLE BATTERIES RECYCLE THEM Topcon Positioning Systems Inc United States Return Process for UsedRechargeable Nickel Metal Hydride Nickel Cadmium Small Sealed Lead Acid and Lithium lon Batteries In the United States Topcon Positioning Systems Inc has established a process by which Topcon customers may return used rechargeable Nickel Metal Hydride Ni MH Nickel Cadmium Ni Cd Small Sealed Lead Acid Pb and Lithium lon Li ion batteries to Topcon for proper recycling and disposal Only Topcon batteries will be accepted in this process Proper shipping requires that batteries or battery packs must be intact and show no signs of leaking T
27. ration 3 Mount two lugs on the RC 4R 4 Push the battery cover lug down until the cover is locked Battery cover lug Battery cover w Connection Lug points BT 66Q 11 Preparation Installing RC 4R onto the Prism Unit A7R4 1 Match the receiving window with the front mark and insert the mounting hooks on the Prism Unit A7R4 into the mounting holes of the RC 4R Mounting hole small Mounting hook small Mounting hole Mounting hook Front mark 2 the RC 4R towards the front mark until you hear a click 12 Preparation Communication between the RC 4R and a Data Collector Bluetooth communication The Bluetooth module built in the RC 4R enables wireless communication with B uetooth compatible equipment Serial signal connector By connecting this connector to a PC or a data collector it will provide the date transmission Mounting Remote Controller Handle Unit RC 4H onto the TS IS QS If you wish to do turn round motions attach the remote controller handle unit RC 4H to the TS IS QS 1 Dismount the handle from TS IS QS Handle unit mounting mark 2 Match the handle unit mounting marks for the RC 4H and TS IS QS 3 sure that the fixing knob is tightly fastened Ensure that the power switch of TS IS QS is off when mounting RC 4H 13 Basic Operation Basic Operation Power Switch ON Press the power switch Power LED will light Power
28. se including any direct indirect consequential damage and loss of profits The manufacturer or its representatives assumes no responsibility for consequential damage and loss of profits by any disaster an earthquake storms floods etc A fire accident or an act of a third party and or a usage any other usual conditions Precautions The manufacturer or its representatives assumes no responsibility for any damage and loss of profits due to a change of data loss of data an interruption of business etc caused by using the product or an unusable product The manufacturer or its representatives assumes no responsibility for any damage and loss of profits caused by usage except for explained in the user manual The manufacturer or its representatives assumes no responsibility for damage caused by wrong movement or action due to connecting with other products Nomenclature and Functions Nomenclature and Functions Remote Controller RC 4R Sighting collimator Receiving window Emitting window Laser beam aperture Panel Antenna for SS wireless Prism unit A7R4 Optional accessory Rear side Bottom Battery cover lug Mounting hole small Mounting hole Battery cover Serial signal RS 232C connector Panel Sending LED Receiving LED Channel display Battery remaining display Power LED Power switch Nomenclature and
Download Pdf Manuals
Related Search