MA DMX MERGER
Contents
1. 931 4979429 www malighting de2. ArtNo 130418 LIGHTING MA DMX MERGER MA DMX MERGERS enable you to mix two DMX signals into one DMX line This is necessary if only one DMX line is available or if you need to improvise using several DMX components The DMX MERGER puts together two DMX lines by using the Highest Takes Precedence mode 0 or the Lowest Takes Precedence mode 1 principle Input B line can be set to a start address offset Mode 3 9 are corresponding to mode 0 but with following additional function A failing DMX signal will not been held on its last value but will be set to 0 Mode 3 switsches off after 3 sec mode 9 after 9 sec first channel line B optically isolated DMX power switch mode inputs A and B DMX output QO O oO Q KAKA SA signal LEDs FEATURES DMX IN Two each optically isolated DMX inputs overvoltage protected DMX OUT Links to other DMX equipment after merging line A and line B INPUT A OFFSET First channel start address input B setting via rotary switches SIGNAL IN A LED indicates valid data receipt on line A SIGNAL IN B LED indicates valid data receipt on line B MODE Optionally different modes currently HTP and LTP TECHNICAL DATA Mains supply 230 VAC 50 Hz or 110 VAC 60 Hz factory setting Signal input output USITT DMX 512 1990 via 5POL XLR Pin layout Pin 1 ground Pin 2 data Pin 3 data Unit dimensions 19 inch 483mm 1U 44 5mm W x H x D mm 435 x 42 x 170 Weight 6 5
3. lbs 3 0 Kg Made in Germany eMail info malighting de Tel 49 931 497940 User s Manual MA DMX Merger 1 MA DMX Merger Safety Instructions NO oF WBN 9 10 11 12 13 14 15 Read all the instructions in the user manual Keep the user manual for later use Follow all the instructions on the unit Pull the plug before cleaning the unit do not use any liquid or spray cleanser Clean with a damp cloth Do not use the unit near water Do not put the unit on unstable tables etc It might fall down and get damaged There are slots in the case for ventilation do not cover these slots up because they guarantee the reliable use of the unit and protect it against overheating Do not install the unit into a frame unless sufficient ventilation is guaranteed The unit is provided with a safety plug This plug can only be used with safety sockets These safety measures should by all means be followed In case the plug does not fit into the socket e g with old sockets the socket should be replaced by an electrician Do not put any objects on the wire and make sure nobody steps on it In case you use an extension wire make sure the sum of the power consumption of the connected units does not exceed the maximum power of the wire The sum of the units plugged in the socket should not exceed 10 Ampere Do not spill any liquid over the unit Do not put any objects through the slots of the u
4. nit as these might get in contact with parts that are live or might cause short circuits This may cause fires and shocks Do not service the unit yourself as parts that are live might be exposed when you open the case you run the risk of getting shocked All services should only be carried out by a specialist If one of the following conditions occurs please pull the plug out and call the service A Wire or plug is damaged or worn B Liquid got into the unit C The unit was exposed to rain or got damp D The unit does not work properly even if you follow the instructions of the user manual E The unit fell down and the case was damaged Only use wires which are marked safety proof Do not use any high power walkie talkies near the unit DECLARATION OF CONFORMITY according to guide lines 89 336 EWG and 92 31 EWG Name of producer MA Lighting Technology GmbH Address of producer Dachdeckerstr 16 D 97297 Waldb ttelbrunn declares that the product Name of product MA Merger Type MA Merger answers the following product specifications Safety EN60065 VDE0860 IEC65 EMV EMC EN55103 1 E1 EN50081 1 EN55103 2 E2 EN50082 1 Additional information All DMX512 inputs and outputs must be shielded and the shielding must be connected to the ground of the corresponding plug Waldbittelbrunn 17 01 1995 M 1 fin Dipl Ing Michael Adenau 2 MA Lighting Technology GmbH Dachdeckerstr 16 97297 Waldbuttelbrunn Fax 49
Download Pdf Manuals
Related Search