User Manual - ADFWeb.com
Contents
1. B Negative wire B 220 ohm A Positive wire ADFweb com Srl IT31010 Mareno Treviso INFO www adfweb com Phone 39 0438 30 91 31 iy User Manual 31939 Modbus Master Document code MN67050_ENG Revision 1 003 Page 11 of 22 Industrial Electronic Devices lt J1939 The connection from CAN socket must be made with a cable with these characteristics DC parameter Impedance 70 Ohm m AC parameters Impedance 120 Ohm m Delay 5 ns m Length Baud Rate bps Length MAX m 10 k 5000 20 k 2500 50 k 1000 100 k 650 125 K 500 250 K 250 500 K 100 800 k 50 1000 k 25 For terminate the CAN line with a 120Q resistor it is necessary to insert the Jumper1 of HD67050 or Jumper3 of HD67050M like in figure Connector2 DeviceNET port Jumper3 Isolated Port Termination DeviceNET Line Open B 120 ohm HO High wire ShlO Shield to Isolated Ground see ohm Lo Low wire HO Shi0 LO Connector4 DeviceNET port Isolated Port THO High wire Shl0 Shield to Isolated Ground Lo shio Ho LO Low wire ADFweb com Srl IT31010 Mareno Treviso INFO www adfweb com Phone 39 0438 30 91 31 iy User Manual 31939 Modbus Master Document code MN67050_ENG Revision 1 003 Page 12 of 22 Industrial Electronic Devices RS232 The connection from RS232 socket to a serial port example one from a personal computer must be made with a Null Modem cable a serial cable wher2. Order Code HD67050 J1939 Modbus Master Converter Order Code HD67050M J1939 Modbus Master Converter Different enclosure ACCESSORIES Order Code AC34107 Null Modem Cable Fem Fem DSub 9 Pin 1 5 m Order Code AC34114 Null Modem Cable Fem Fem DSub 9 Pin 5 m Order Code AC34001 Rail DIN Power Supply 220 240V AC 50 60Hz 12 V AC Order Code AC34002 Rail DIN Power Supply 110V AC 50 60Hz 12 V AC ADFweb com Srl IT31010 Mareno Treviso INFO www adfweb com Phone 39 0438 30 91 31 iy User Manual 31939 Modbus Master Document code MN67050_ENG Revision 1 003 Page 21 of 22 Industrial Electronic Devices DISCLAIMER All technical content within this document can be modified without notice The content of the document content is a recurring audit For losses due to fire earthquake third party access or other accidents or intentional or accidental abuse misuse or use under abnormal conditions repairs are charged to the user ADFweb com S r l will not be liable for accidental loss of use or inability to use this product such as loss of business income ADFweb com S r l shall not be liable for consequences of improper use OTHER REGULATIONS AND STANDARDS WEEE INFORMATION Disposal of old electrical and electronic equipment as in the European Union and other European countries with separate ps collection systems m his symbol on the product or on its packaging indicates that this product may not be tre
3. field Baud Rate the baudrate for the serial line is defined Cyclic Delay ioo O O In the field Parity the parity of the serial line is defined Inthe field Stop Bit the number of Stop Bit is defined In the field TimeOut there is the maximum time that the device attends for the answer from the Slave interrogated Inthe field Cyclic Delay the delay between two requests is defined Figure 4 Set Communication window ADFweb com Srl IT31010 Mareno Treviso INFO www adfweb com Phone 39 0438 30 91 31 AL User Manual 31939 Modbus Master Document code MN67050_ENG Revision 1 003 Page 15 of 22 Industrial Electronic Devices FRAME 31939 By pressing the Frame J1939 button from the main window for SW67050 Fig 3 the window J1939 frame appears Fig 5 The means for the fields are ka Figure 5 J1939 Frame window In the field Priority insert the priority of the frame in the J1939 protocol is a number among 0 1 2 3 4 5 6 7 The number 0O is the highesst and the 7 is the lowest In the field Data Page insert the data page in the J1939 protocol is O or 1 In the field PGN insert the PGN of the data you would to read from modbus to J1939 in the J1939 protocol the PGN is an identifier In the field Group it is possible to select when the frame is sent at J1939 side The groups are defined under the section Setting Group If no
4. is better if the first time you do the update of the Firmware in the HD67050 or HD67050M device Warning A If the Fig 8 appears when you try to do the Update before require assistance try sw67050 AEE these points Ver 1 000 INIT PROTECTION Check if the serial COM port selected is the correct one Check if the serial is connected between the PC and the device FIRMWARE PROTECTION Try to repeat the operations for the updating mene oat E If you are using a dongle try with a native COM port or change the dongle Try with another PC Try to restart the PC If you are using the program inside a Virtual Machine try to use in the main Figure 9 Protection window Operating System A In the case of HD67050 or HD67050M you have to use the software SW67050 www adfweb com download filefold SW67050 zip ADFweb com Srl IT31010 Mareno Treviso INFO www adfweb com Phone 39 0438 30 91 31 User Manual 31939 Modbus Master Document code MN67050_ENG Revision 1 003 Page 20 of 22 AL Industrial Electronic Devices MECHANICAL DIMENSIONS 120 mm GOQOUO6 co E O rd E ES Dei gt ae 3 Bm OFS 6 lt OCO OAO09O 9 fe amp i T 2 79 inch 2 36 inch Housing PVC 23 mm Housing PVC Weight 200g Approx 0 9 inch Weight 200g Approx Figure 11 Mechanical dimensions scheme for HD67050 Figure 12 Mechanical dimensions scheme for HD67050M ORDER CODES
5. to exchange or repair it please do the following 1 Obtain a Product Return Number PRN from our internet support at www adfweb com Together with the request you need to provide detailed information about the problem 2 Send the product to the address provided with the PRN having prepaid the shipping costs shipment costs billed to us will not be accepted If the product is within the warranty of twelve months it will be repaired or exchanged and returned within three weeks If the product is no longer under warranty you will receive a repair estimate PRODUCTS AND RELATED DOCUMENTS Part Description URL HD67216 CAN bus Analyzer www adfweb com product HD67216 HD67121 Gateway CANopen Canopen www adfweb com product HD67121 HD67004 4D67005 Gateway CANopen Modbus Ethernet TCP www adfweb com product HD67004 HD67134 Gateway CANopen DeviceNet www adfweb com product HD67134 HD67117 CAN bus Repeater www adfweb com product HD67117 HD67502 Gateway CANopen Modbus RTU www adfweb com product HD67502 ADFweb com Srl IT31010 Mareno Treviso INFO www adfweb com Phone 39 0438 30 91 31
6. O Shi0 LO S Shield to Ground Boot Mode Blink quickly B Negative wire No Boot Mode RUN A Positive wire Connector4 RS232 Port D SUB9 Male PIN2 RX PIN3 TX PINS GND pI Used for Programmation Port Modbus on R5232 To connect the device to the COM port of a PC in order to set it you have to use the programming cable AC34107 or a cable made Isolated CAN Modbus on amp port RS485 port Hoa aoe HO Shid LO S E _ Boot Mode LEA a i Normal Mode Jumper3 Boot mode Yes Jumper Figure 1 Connection scheme for HD67050 ADFweb com Srl IT31010 Mareno Treviso INFO www adfweb com Phone 39 0438 30 91 31 User Manual 31939 Modbus Master Document code MN67050_ENG Revision 1 003 Page 5 of 22 Industrial Electronic Devices Jumper3 Jumper2 Termination Modbus Line Termination CAN Line Open E 120 ohm S Shield to Isolated Ground 220 ohm B Negative wire A Positive wire lsolated Port SS HO High wire LO Shi0 HO ShiO Shield to Isolated Ground fa Yes Jumper Boot Mode c ABS No Jumper Normal Mode Leda Z Se Connector2 Notused WOWDOeweeVe RS232 Port D SUB9 Male Led3 Not used Programmation Port Modbus on RS232 To connect the device to the COM port of a PC in order to set it you have to use the programming cable AC34107 or a cable made as showed her
7. User Manual 31939 Modbus Master Document code MN67050_ENG Revision 1 003 Page 1 of 22 Industrial Electronic Devices User Manual Revision 1 003 English pae hus NTE ee L WARNE Il e IE Il mt HDS it 31939 Modbus Master Converter Order Code HD67050 HD67050M HD67050 HD67050M for Website information For others Gateways Bridges www adfweb com Product HD67050 J1939 to Modbus See also the following links for T AN a HD67050 bee www adfweb com Product HD67215 Modbus TCP WWW W aula www adfweb com Price HD67050M CANopen to Modbus See also the following links www adfweb com Product HD67001 Modbus RTU Master www adfweb com Product HD67002 Modbus RTU Slave www adfweb com Product HD67004 Modbus TCP Master Benefits and Main Features www adfweb com Product HD67505 Modbus TCP Slave For others Gateways Bridges Very easy to configure For CAN bus 2 0A and or CAN bus 2 0B to Modbus See also the following links Low cost www adfweb com Product HD67011 Modbus RTU Slave www adfweb com Product HD67012 Modbus RTU Master Modbus RTU on Serial RS232 485 Benefit www adfweb com Product HD67014 Modbus TCP Slave www adfweb com Product HD67515 Modbus TCP Master RS232 485 selection Do you have an your customer protocol Galvanic isolation See the following links www adfweb com Product HD67003 Industrial temperature range 40 C 85 C 40 F 185 F Do
8. ated as household rubbish Instead it Should be taken to an applicable collection point for the recycling of electrical and electronic equipment If the product is disposed correctly you will help prevent potential negative environmental factors and human health which could otherwise be caused by inappropriate disposal The recycling of materials will help to conserve natural resources For more information about recycling this product please contact your local city office your household waste disposal service or the shop where you purchased the product RESTRICTION OF HAZARDOUS SUBSTANCES DIRECTIVE 4 The device respects the 2002 95 EC Directive on the restriction of the use of certain hazardous substances in electrical Oo and electronic equipment commonly referred to as Restriction of Hazardous Substances Directive or ROHS 2002 95 EC CE MARKING C The product conforms with the essential requirements of the applicable EC directives ADFweb com Srl IT31010 Mareno Treviso INFO www adfweb com Phone 39 0438 30 91 31 AL User Manual 31939 Modbus Master Document code MN67050_ENG Revision 1 003 Page 22 of 22 Industrial Electronic Devices WARRANTIES AND TECHNICAL SUPPORT For fast and easy technical support for your ADFweb com SRL products consult our internet support at www adfweb com Otherwise contact us at the address support adfweb com RETURN POLICY If while using your product you have any problem and you wish
9. be powered between a wide range of tensions For more details see the two tables below dae ich Consumption at 24V DC owe woa HD67050 4 A Caution Not reverse the polarity power V Positive wire V AC min 8V max 19v V DC min 8v max 35v OV Ground V Positive wire HD67050 HD67050M V AC min 8V max 19v V DC min 8v max 35v ADFweb com Srl IT31010 Mareno Treviso INFO www adfweb com Phone 39 0438 30 91 31 User Manual 31939 Modbus Master Document code MN67050_ENG Revision 1 003 Page 8 of 22 AL Industrial Electronic Devices FUNCTION MODES The device has got two functions mode depending of the position of the Jumper3 of HD67050 or Jumperi of HD67050M The first without any jumper inserted is used for the normal working of the device The second with the jumper inserted is used for upload the Project For the operations to follow for the updating see UPDATE DEVICE section According to the functioning mode the LEDs will have specifics functions see LEDS section Yes Jumper Boot Mode No Jumper Normal Mode Jumperi Boot mode is Yes Jumper Boot Mode J No Jumper Normal Mode ADFweb com Srl IT31010 Mareno Treviso INFO www adfweb com Phone 39 0438 30 91 31 AL User Manual 31939 Modbus Master Document code MN67050_ENG Revision 1 003 Page 9 of 22 Industrial Electronic Devices LEDS The d
10. can be used only by qualified personnel strictly in accordance with the specifications Qualified personnel are persons who are familiar with the installation assembly commissioning and operation of this equipment and who have appropriate qualifications for their job RESIDUAL RISKS The device is state of the art and is safe The instrument can represent a potential hazard if they are inappropriately installed and operated by personnel untrained These instructions refer to residual risks with the following symbol This symbol indicates that non observance of the safety instructions is danger for people to serious injury or death and or the A possibility of damage CE CONFORMITY The declaration is made by us You can send an email to support adfweb com or give us a call if you need it ADFweb com Srl IT31010 Mareno Treviso INFO www adfweb com Phone 39 0438 30 91 31 AL aA User Manual 31939 Modbus Master i i Document code MN67050_ENG Revision 1 003 Page 4 of 22 Industrial Electronic Devices l CONNECTION SCHEME CAN port _ Isolated Port Connector1 Power Supply Jumperi eaa Termination CAN Line HO High wire Jumperz OV Ground Shi0 Shield to Isolated Ground Termination Modbus Line y iti vir l f j V Positive wire LO kow wire Open EME 220 ohm 12 VAC min 8v max 19v 4 VA i 24 VDC min 8v max 35v 4 Watt Connectors iIModbus on RS485 OV V H
11. de and download the updates To obtain the updated documentation for the product that you own note the Document Code Abbreviated written Doc Code on the label on the product and download the updated from our web site www adfweb com download REVISION LIST Revision Date Author Chapter Description 1 000 23 01 2009 Fl All First release version 1 001 21 07 2010 Fl All Revision 1 002 01 02 2012 Fl All Revision 1 003 18 02 2013 Nt All Added new chapters WARNING ADFweb com reserves the right to change information in this manual about our product without warning ADFweb com is not responsible for any error this manual may contain TRADEMARKS All trademarks mentioned in this document belong to their respective owners INFO www adfweb com Phone 39 0438 30 91 31 iy User Manual 31939 Modbus Master Document code MN67050_ENG Revision 1 003 Page 3 of 22 Industrial Electronic Devices SECURITY ALERT GENERAL INFORMATION To ensure safe operation the device must be operated according to the instructions in the manual When using the device are required for each individual application legal and safety regulation The same applies also when using accessories INTENDED USE Machines and systems must be designed so the faulty conditions do not lead to a dangerous situation for the operator i e independent limit switches mechanical interlocks etc QUALIFIED PERSONNEL The device
12. e Positive wire 12 VAC min 8v max 19v 4 VA 24 VDC min 8v max 35v 4 Watt E CABLE Boot Mode Blink quickly Side B No Boot Mode RUN FEM Figure 2 Connection scheme for HD67050M ADFweb com Srl IT31010 Mareno Treviso INFO www adfweb com Phone 39 0438 30 91 31 AL User Manual 31939 Modbus Master Document code MN67050_ENG Industrial Electronic Devices CHARACTERISTICS The configurable J1939 from to Modbus Master gateway allow the following iF Baud rate changeable with software Electrical isolation between two buses It allows to read through J1939 frames the data that the Gateway ask to Modbus devices Power supply of 8 19 VAC 4VA or 8 35 VDC 4W 35mm Rail DIN mounting Temperature range 40 C to 85 C CONFIGURATION The Gateway J1939 into Modbus allows a J1939 network to communicate with a Modbus network You need Compositor SW67050 software on your PC in order to perform the following kai kai kai ADFweb com Srl IT31010 Mareno Treviso INFO www adfweb com Define the communication parameters of two lines Define the J1939 frames Define which Modbus Registers read Update the Firmware and or Project Revision 1 003 Page 6 of 22 Phone 39 0438 30 91 31 AL User Manual 31939 Modbus Master Document code MN67050_ENG Revision 1 003 Page 7 of 22 Industrial Electronic Devices LO POWER SUPPLY The devices can
13. e the HD amp 7050 from RS232 Connect the RS232 Null Modem Cable form your PC to the Gateway 1 Turn OFF the Device Insert the Boot Jumper For more info see Fig 1 or Fig 2 2 Insert the Boot Jumper see the manual Select the COM port and press the Connect button 3 Select the COM port and press the connect button Turn on the device Sou id Check the BOOT Led It must blink quickly see LEDS section Be Tabi Out ane Eayize Press the Next button 5 Check the BOOT led It must blink quickly Select which operations you want to do Press the Execute update firmware button to start the upload When all the operations are OK turn off the device Disconnect the Boot jumper Update Device Options Disconnect the RS232 Cable vi Firmware Turn on the device Wf Read Firmware when finish rl Project Update Firmware from Serial R 232 At this point the configuration firmware on the device is correctly update Nee RST W6 050 Serial Update Execute update firmware a Ver 1 000 INIT Waiting FIRMWORE Waiting PROJECT Waiting Figure 8 Update Device windows ADFweb com Srl IT31010 Mareno Treviso INFO www adfweb com Phone 39 0438 30 91 31 User Manual 31939 Modbus Master Document code MN67050_ENG Revision 1 003 Page 19 of 22 Industrial Electronic Devices J Note Es When you install a new version of the software it
14. e the pins 2 and 3 are crossed It is recommended that the RS232C Cable not exceed 15 meters The serial port is used for programming the device or for Modbus communication NULL MODEM CABLING 98 76 54321 CABLE CABLE Side A Side B FEM FEM ADFweb com Srl IT31010 Mareno Treviso INFO www adfweb com Phone 39 0438 30 91 31 iy User Manual 31939 Modbus Master Document code MN67050_ENG Revision 1 003 Page 13 of 22 Industrial Electronic Devices USE OF COMPOSITOR SW67050 To configure the Gateway use the available software that runs with Windows _ AOFweb com Compositor SW6 7050 31939 TO MODBUS RTU Master Example1 called SW67050 It is downloadable on the site www adfweb com and its operation is described in this document When launching the SW67050 the right window appears Fig 3 g Frame 1939 LI Define 11939 g Setting Group ey Update Device www ADFaeb com Figure 3 Main window for SW67050 NEW PROJECT OPEN PROJECT The New Project button creates the folder which contains the entire device configuration A device configuration can also be imported and exported To clone the configurations of a programmable J1939 from to Modbus Gateway in order to configure another device in the same manner it is necessary to maintain the folder and all its contents To clone a project in order to obtain a different version of the project it is sufficient to duplicate the project fo
15. evice has got three LEDs that are used to give information of the functioning status The various meanings of the LEDs are described in the table below HD67050 HD67050M LED Normal Mode Boot Mode LED Normal Mode Boot Mode 1 Off 1 Blinks slowly 1Hz Blinks quickly 2 Off 2 Off 3 Blinks slowly 1Hz Blinks quickly 3 Off Off Green Boot Mode Blink quickly No Boot Mode RUN Boot Mode Blink quickly No Boot Mode RUN i ADFweb com Srl IT31010 Mareno Treviso INFO www adfweb com Phone 39 0438 30 91 31 User Manual 31939 Modbus Master Document code MN67050_ENG Revision 1 003 Page 10 of 22 AL Industrial Electronic Devices RS485 For terminate theRS485 line with a 220 resistor it is necessary to insert the Jumper like in figure Connector3 Modbus on RS485 The maximum length of the cable should be 1200m 4000 feet S Shield to Ground B Negative wire CEE 220 ohm A Positive wire Here some codes of cables Belden p n 8132 2x 28AWG stranded twisted pairs conductor foil shield braid shield Belden p n 82842 2x 24AWG stranded twisted pairs conductor foil shield braid shield Tasker p n C521 1x 24AWG twisted pair conductor foil shield braid shield Tasker p n C522 2x 24AWG twisted pairs conductor foil shield braid shield Connectors Modbus on R5485 Modbus Line Isolated Port H Open S Shield to Isolated Ground
16. group is selected the default is On request so another J1939 device have to made the request to the gataway and then it sends the frame If the field Erase is checked if the Master Modbus don t receive the reply to his request before the Timeout ms defined in Set Communication puts the value of the J1939 frame at O In the field Mnemonic it is possible to insert a description amp J1939 Frame Sex Priority Data Page Group Mnemonic al 100 tenth of G2 1000 second 63 500 half second G2 1000 second G2 1000 second Fs Engine Speed Copland Temperature Fuel Oil Pressure Coolant Battery Volkage Barometric pressure Intake On Request Fuel Consumption Rate On Request Comulative Fuel Consumption 63 500 half second mm Mm Om mm Mm mom Mm mh oO om A oO A oO oO A Intake Mainfold Pressure 1 2 a 4 a 6 T a g eo ONOOOOOUOUOOO ADFweb com Srl IT31010 Mareno Treviso INFO www adfweb com Phone 39 0438 30 91 31 AL User Manual 31939 Modbus Master Document code MN67050_ENG Revision 1 003 Page 16 of 22 Industrial Electronic Devices DEFINE J1939 3 Define Frames J1939 By pressing the Define J1939 button from the main window for mopeus Correlated SW67050 Fig 3 the window Define Frames J1939 appears Fig 6 PRI DP Device ID Ind MB O 1 Index MODBUS 1 In the field Correlated there are PGN who you insert in the list Fra
17. lder with another name and open the new folder with the button Open Project When a new project is created or an existent project is open it will be possible to access the various configuration section of the software o Set Communication o Define the 31939 frames o Define which Modbus registers read ADFweb com Srl IT31010 Mareno Treviso INFO www adfweb com Phone 39 0438 30 91 31 AL Document code MN67050_ENG Revision 1 003 Industrial Electronic Devices SET COMMUNICATION SET COMMUNICATION 11939 This section defines the fundamental communication parameters of two Buses J1939 and Modbus By pressing the Set communication button from the main window for SW67050 Fig 3 the window Set Communication appears Fig 4 Baud rate Dey ID This window is divided in two sections one for the J1939 and the other for the Modbus ModBus RTU The means of the fields for J1939 are In the field Baud rate it is possible to select the Baud rate of the J1939 line O RS232 Inthe field Ded ID is possible to assign an ID at the J1939 side Baud rate The means of the fields for Modbus are an If the field RS232 is checked the serial line in use is the RS232 otherwise if the field Son BL RS485 is checked the serial line in use is the RS485 Timeout ms User Manual 31939 Modbus Master Page 14 of 22 RS485 115200 NONE 1 Stop Bit Inthe
18. me J1939 In the field MODBUS there are the modbus words taht you have Number of Point created for each PGN 1 om Oo Oo Oh h Oh oh oh ooo Oooo oe For create a Modbus register you have to select the desired PGN then Type of Data Input Register In the field Device ID insert the ID of the slave Modbus device that contain the register In the field Index MODBUS you have to insert the Address of the register In the filed Number of Points you have to select the number of consecutive registers to be read In the field Type of Data you have to select which type of data to read After that selecting the various Ri R2 R3 R4 R5 R6 R7 R8 it is possible to define in the Selected Frame Bytes how the modbus value is put into the J1939 frame If you have selected Number of Point 1 you can use only the R1 if you have selected 3 you can use only the R1 R2 and R3 And so on Then press the New button for add the created reg ister Tanslate in Low MODBUS Byte Tanslate in High MODBLS Byte You can add a new modbus word by pressing the New button modify an existing one by pressing Modify delete by pressing Delete copy and paste Figure 6 Define Frames J1939 window ADFweb com Srl IT31010 Mareno Treviso INFO www adfweb com Phone 39 0438 30 91 31 AL User Manual 31939 Modbus Master Document code MN67050_ENG Revi
19. sion 1 003 Page 17 of 22 Industrial Electronic Devices SETTING GROUP By pressing the Setting Group button from the main window of SW67050 the window Groups Setting appears Fig 7 It is possible to define a maximum of ten groups These groups are used in the J1939 Frame for define when the gateway sends the frames Each group is composed of a Cyclic Time ms and a Mnemonic The means for the fields are In the field Cyclic Time ms insert a time expressed in milliseconds This time is used for send cyclically the J1939 frames with this group defined in the J1939 Frame when the time is expired Inthe field Mnemonic it is possible to insert a description Groups Setting Cyclic Time mS Mnemonic 100 tenth of second 1000 second sog half second 1 2 d 4 5 6 T a g _ Figure 7 Groups Setting window ADFweb com Srl IT31010 Mareno Treviso INFO www adfweb com Phone 39 0438 30 91 31 iy User Manual 31939 Modbus Master Document code MN67050_ENG Revision 1 003 Page 18 of 22 Industrial Electronic Devices UPDATE DEVICE By pressing the Update Device button it is possible to load the created Configuration into the device and also the Firmware if is necessary In order to load the parameters or update the firmware in the device follow these instructions T Firmware from Serial RS232 Turn off the Device Follow this step to updat
20. you need to choose a device do you want help Ask it to the following link www adfweb com Cmd helpme ADFweb com Srl IT31010 Mareno Treviso INFO www adfweb com Phone 39 0438 30 91 31 Industrial Electronic Devices INDEX INDEX UPDATED DOCUMENTATION REVISION LIST WARNING TRADEMARKS SECURITY ALERT CONNECTION SCHEME CHARACTERISTICS CONFIGURATION POWER SUPPLY FUNCTION MODES LEDS RS485 J1939 RS232 USE OF COMPOSITOR SW67050 NEW PROJECT OPEN PROJECT SET COMMUNICATION FRAME J1939 DEFINE J1939 SETTING GROUP UPDATE DEVICE MECHANICAL DIMENSIONS ORDER CODE ACCESSORIES DISCLAIMER OTHER REGULATIONS AND STANDARDS WARRANTIES AND TECHNICAL SUPPORT RETURN POLICY PRODUCTS AND RELATED DOCUMENTS ADFweb com Srl IT31010 Mareno Treviso ODNADAWNNNNNG M NNNNNNNNRFPRPRBPB BBB BBB NNNFFODOOONADAUARAWWNHO User Manual 31939 Modbus Master Document code MN67050_ENG Revision 1 003 Page 2 of 22 UPDATED DOCUMENTATION Dear customer we thank you for your attention and we remind you that you need to check that the following document is gt Updated gt Related to the product you own To obtain the most recently updated document note the document code that appears at the top right hand corner of each page of this document With this Document Code go to web page www adfweb com download and search for the corresponding code on the page Click on the proper Document Co
Download Pdf Manuals
Related Search