Home
LED Crystal Magic Ball Light
Contents
1. Instruction Manual LED Crystal Magic Ball Light LED Crystal Magic Ball Light Instruction Manual LED Crystal Magic Ball Light is advanced LED Technology with compact plastic shell delivering 34 razor sharp powerful beams Project light beams on the wall just like a mirror ball effect 2 DMX channels speed control Three control mode DMX Master slave and sound active Stand alone and rotating via dip switch Advanced LED technology creating powerful beams similar to a 150W discharge lamp Extremely long lift rated 100 000 hrs no need to change lamp Very low power consumption no duty cycle runs all light Very compact shell perfect using for discos clubs pubs parties WARNING FOR YOUR OWN SAFETY PLEASE READ THIS USER MANUAL CAREFULLY BEFORE YOUR INITIAL START UP The manufacturer will not accept liability for any resulting damages caused by the non observance of this manual or any unauthorized modification to the eguipment e Never let the power cable come into contact with other cables Handle the power cable and all mains voltage connections with particular caution e Never remove warning or informative labels from the equipment Do not open the equipment and do not modify the equipment e Do not connect this equipment to a dimmer pack e Do not switch the equipment on and off in short intervals as this will reduce the system s life e Only use the equipment indoors Do not expose to flammable sources liguids o
2. 22 454480 e 20 72 104 196 168 200 202 204 200 328 360 392 424 456 ass ra e 73 105 137 169 201 1203 205 207 320 261 300 425 457 409 efas 0 112 144 176 208 240 272 204 336 308 400 432 404 406 122 54 86 118 180 102 214 246 270 310 34 374 406 438 470 502 125 57 60 121 159 85 217 240 281 919 345 377 200 421 473 505 126 56 00 122 154 188 218 260 262 14 346 370 410 442 474508 2a 60 2 124 150 188 220 252 264 310 348 380 412 444 476 500 Dip Switch position DMX Address 06
3. ating fuse gt 2MO Channels 6channel Beam angle 150 degree Size 210x210x179mm Packing Size 280x260x240mm N W 1 8kg G W 2 5kg Operations There are 4 operating modes to choose from 1 DMX mode 2 Auto Run mode 3 Sound active mode 4 Slave mode DMX Mode To select DMX mode set dipswitch 1 to ON You can now set the reguired DMX address using dipswitches 2 to 10 The start address for this fixture is O Please refer to the chart below for DMX functions Auto Run Function Mode To select auto pattern mode set all dipswitches to the OFF position The unit will now cycle through all it s built in patterns In this mode the LEDs will remain constantly chasing until the power is turned OFF or the mode is changed Sound Active Mode To select sound active mode set dipswitch 10 to ON You can now use the sensitivity control on the back panel to set the required sound input level With no music present the LEDs will turn OFF and will come back ON as soon as the music starts again Slave Mode To select the slave mode set dipswitch 1 to OFF and others to ON The slave units will now follow in conjunction with the master unit Note The master unit can be run in any mode for the slave units to follow 02 LED Crystal Magic Ball Light Instruction Manual Overview Front Identification 1 DMX In 4 Power Diswitches 2 DMX Out 5 Fuse 8 LED Power light 3 Soun
4. d sensitivity control 6 MIC 9 Lens FUCTION INTRODUTION It can be controlled by internationally DMX512 signal also control with single light via dip switch and Master salve control lt is extremely easy to use DMX 512 control first connect from consoleto the signal input of first light with XRL and then connect from signal output of first light to the signal input of the second light as the same step to the last one for example DMX512 gt Controller line Controlled line x N Controlled line First Lights Second Lights N Lights 3 Before using of DMX512 control please turn power on the light Note Please keep in mind that the signal output of final lamp should be connected to the circuit plug circuit plug has a 120 ohm resistance between 2 feet and 3 feet the circuit plus can avoiding signal reflecting phenomenon during DMX 512 transmission 03 LED Crystal Magic Ball Light Instruction Manual Console channel instruction mamma e Oi O TE EEE E BEE DIP switch control by DMX 512 take the console of CH16 and CH20 for example J eonsolerofehannei 16 consoler of channel 20 men fs tas _ mew fs DMX 512 DMX Digital Multiplex is a universal protocol used as a form of communication between intelligent fixtures and controllers A DMX controller sends DMX data inst
5. he last unit to avoid erratic behaviour Termination reduces signal transmission problems and interferance itis always advisable to connect a a DMX terminal resistance 120 Ohm 1 4 W between pin 2 DMX and pin 3 DMX of the last fixture Using a cable terminator part number CABL90 will decrease the possibilities of erratic behaviour 5 Pin XLR DMX Connectors Some manufactures use 5 pin XLR connectors for data transmission in place of 3 pin 5 Pin XLR fixtures may be implemented in a 3 pin XLR DMX line When inserting standard 5 pin XLR connectors in to a 3 pin line a cable adaptor must be used The Chart below details the correct cable conversion 3 Pin XLR to 5 PIN XLR Conversion Conductor 3 Pin XLR out 5 Pin XLR in Ground shield Pin 1 Pin 1 Negative Pin 2 Pin 2 Positive Pin 3 Pin 3 05 LED Crystal Magic Ball Light Instruction Manual DMX Dip Switch Quick Reference Chart Dip Switch Position pmxoipswirch 8 o o o o o o o o 1 1 1111111 ez oa se 1201100 192 224 256 288 320 352 364 410 48 180 72 54 66 oe 190 162 194 226 208 200 322 354 386 418 450 402 ra a5 67 oo 131 169 105 227 250 201 223 255 387 419 451 ass ra 36 60 100 132 164 196 226 200 202 324 356 988 420 452 484 s 8760 101 139 165 197 200 261 208 325 307 300 421 ass ass e 06 70 102 134 165 198 200 262 204 326 358 990 4
6. r gases e Always disconnect the power from the mains when eguipmentis not in use or before cleaning Only handle the power cable by the plug Never pull out the plug by pulling the power cable e Make sure that the available voltage is between 110v 240v e Make sure that the power cable is never crimped or damaged Check the equipment and the power cable periodically elf the equipment is dropped or damaged disconnect the mains power supply immediately Have a qualified engineer inspect the equipment before operating again e f the equipment has been exposed to drastic temperature fluctuation e g after transportation do not switch it on immediately The arising condensation might damage the equipment Leave the equipment switched off until it has reached room temperature elf your product fails to function correctly discontinue use immediately Pack the unit securely preferably in the original packing material and return it to your Prolight dealer for service Only use fuses of same type and rating e Repairs servicing and power connection must only be carried out by a qualified technician THIS UNIT CONTAINS NO USER SERVICEABLE PARTS e WARRANTY One year from date of purchase CAUTION TAKE CARE USING THIS EQUIPMENT HIGH VOLTAGE RISK OF ELECTRIC SHOCK 01 LED Crystal Magic Ball Light Instruction Manual Technical Specifications Voltage ACV90 240V 50 60Hz Lamp 1 pcs of 3W LED Multi color RGB Power 10W Insul
7. ructions form the controller to the fixture DMX data is sent as serial data that travels from fixture to fixture via the DATA IN and DATA OUT XLR terminals located on all DMX fixtures most controllers only have a data out terminal DATA Cable DMX cable requirements for DMX operation e The Equinox Triclops can be controlled via DMX 512 protocol The DMX address is set on the back of the unit Your unit and your DMX controller require a standard 3 pin XLR connector for data input output figure 1 Figure 1 Further DMX cables can be purchased from all good sound and lighting suppliers or Prolight dealers Please quote CABL10 2M CABL11 5M CABL12 10M Also remember that DMX cable must be daisy chained and cannot be split 04 LED Crystal Magic Ball Light Instruction Manual Notice Be sure to follow figures 2 amp 3 when making your own cables Do not connect the cable s shield conductor to the ground lug or allow the shield conductor to come in contact with the XLR s outer casing Grounding the shield could cause a short circuit and erratic behaviour common DMX 512 out 3 pin XLR DMX 512 in 3 pin XLR XLR MALE SOCKET XLR FEMALE SOCKET XLR Pin Configuration 2 cold 1 ground 1 ground scold Pin 1 Ground Pin 2 Negative 3Hot 3Hot Pin 3 Postive FIGURE 3 FIGURE 2 Special Note Line termination e When longer runs of cable are used you may need to use a terminator on t
Download Pdf Manuals
Related Search
Related Contents
HDR-AS30 / AS30V html .pi: A Simple HTML Package for Prolog and CLP Systems Manual de montaje Business Terms and Conditions for Homebanking 1_01-04 Titel…Ausbau STR6100 QLogic PathScale™ Compiler Suite User Guide Manuale d`installazione DINION 7000 Camera Kit Guía del usuario Skil 4900 AG Add-On DST Adapter Model DST6501 Quick Start Guide Copyright © All rights reserved.
Failed to retrieve file