Model 69254-006 Master Control Unit PCBA - GAI
Contents
1. connection Reserved for use by authorized factory personnel The Ethernet port is located on the rear connector panel directly behind the MCU slot in the card rack Connection to this port is made through a standard RJ 45 8 pin connector s_eng gtcproddocs standard ioms current release 42004 instr manuals 42004 64912a doc 10 02 Pub 42004 649L2A 69254 006 MCU PCBA PAGE 3 OF 10 Installation Warnings Please observe the following warnings or damage to the equipment may result N WARNING Ax Disconnect power to the card rack before performing any maintenance ie Warning Observe precautions for handling electrostatic sensitive devices General Installation Notes Refer to Figure 1 for component location and installation details 1 Remove the MCU from its carton 2 Verify that power is disconnected to the card rack prior to installation 3 Verify the MODE switch settings S2 1 S3 0 4 Connect battery connector to J13 5 Find the slot located on the farthest left side of the card rack 6 Align the MCU into the upper and lower tracks for the slot 7 Connect the RJ45 connector cable inside the card rack to the mating connector on the Ethernet PCBA 8 Slide the MCU toward the rear of the card rack until it comes in contact with the connector on the backplane Use caution to avoid pinching the Ethernet cable 9 Firmly press on the front bezel until the MCU is seated in the backplane connector and tighten t2. copyright treaties as well as other intellectual property laws and treaties The SOFTWARE is licensed not sold 1 GRANT OF LICENSE This EULA grants you the following rights e Software You may use the SOFTWARE as installed on the SYSTEM e Application Sharing The SOFTWARE may contain technology that enables applications to be shared between two or more SYSTEMS even if an application is installed on only one of the SYSTEMS You should consult your application license agreement or contact the application licensor to determine whether sharing the application is permitted by its licensor e Storage Network Use If the SOFTWARE PRODUCT is installed on the SYSTEM over an internal network from a server you must acquire and dedicate a license for the SOFTWARE PRODUCT for each SYSTEM on which the SOFTWARE PRODUCT is used or to which it is distributed A license for the SOFTWARE PRODUCT may not be shared or used concurrently on different SYSTEMS e Back up Copy If Manufacturer has not included a copy of the SOFTWARE on a separate media with the SYSTEM you may make a single copy of the SOFTWARE for use solely for archival purposes with the SYSTEM 2 DESCRIPTION OF OTHER RIGHTS AND LIMITATIONS e Limitations on Reverse Engineering Decompilation and Disassembly You may not reverse engineer decompile or disassemble the SOFTWARE except and only to the extent that such activity is expressly permitted by applicable law notwithstanding this lim
3. 30 REF 261 6 9 19 REF 233 4 BATTERY TIE WRAP COM 2 __ CLIT E COPE E TET A gig J PCBA O RS J 9 DISKONCHIP BATTERY CONNECTOR 1 58 REF Figure 1 Model 69254 006 Master Control Unit PCBA Description of Major Components Serial Port 2 COM2 is located on the front of the MCU bezel COM2 allows connection to an external PC for transferring the system configuration software Parallel port support is provided on the MCU The parallel port is located on the rear of the card rack assembly directly behind the MCU slot and provides printer output from the MCU to a logging printer Keyboard support is provided by the MCU The keyboard interface is located on the rear of the card rack assembly control panel directly behind the MCU slot Connection to this port is made through a standard keyboard connector A CAUTION J Keyboard is not a user
4. ANY DAMAGES SUFFERED OR INCURRED BY THE END USER INCLUDING BUT NOT LIMITED TO GENERAL SPECIAL CONSEQUENTIAL OR INCIDENTAL DAMAGES INCLUDING DAMAGES FOR LOSS OF BUSINESS PROFITS BUSINESS INTERRUPTION LOSS OF BUSINESS INFORMATION AND THE LIKE ARISING FROM OR IN CONNECTION WITH THE DELIVERY USE OR PERFORMANCE OF THE SOFTWARE NOTE ON JAVA SUPPORT THE SOFTWARE PRODUCT MAY CONTAIN SUPPORT FOR PROGRAMS WRITTEN IN JAVA JAVA TECHNOLOGY IS NOT FAULT TOLERANT AND IS NOT DESIGNED MANUFACTURED OR INTENDED FOR USE OR RESALE AS ON LINE CONTROL EQUIPMENT IN HAZARDOUS ENVIRONMENTS REQUIRING FAIL SAFE PERFORMANCE SUCH AS IN THE OPERATION OF NUCLEAR FACILITIES AIRCRAFT NAVIGATION OR COMMUNICATIONS SYSTEMS AIR TRAFFIC CONTROL DIRECT LIFE SUPPORT MACHINES OR WEAPONS SYSTEMS IN WHICH THE FAILURE OF JAVA TECHNOLOGY COULD LEAD DIRECTLY TO DEATH PERSONAL INJURY OR SEVERE PHYSICAL OR ENVIRONMENTAL DAMAGE Page 4 of 4 U S GOVERNMENT RESTRICTED RIGHTS The SOFTWARE and documentation are provided with RESTRICTED RIGHTS Use duplication or disclosure by the Government is subject to restrictions as set forth in subparagraph c 1 ii of the Rights in Technical Data and Computer Software clause at DFARS 252 227 7013 or subparagraphs c 1 and 2 of the Commercial Computer Software Restricted Rights at 48 CFR 52 227 19 as applicable Manufacturer is Microsoft Corporation One Microsoft Way Redmond WA 98052 6399 If you acquired this EULA in the
5. Pub 42004 649L2A A GAI TRONICS CORPORATION A HUBBELL COMPANY Model 69254 006 Master Control Unit PCBA Confidentiality Notice This manual is provided solely as an operational installation and maintenance guide and contains sensitive business and technical information that is confidential and proprietary to GAI Tronics GAI Tronics retains all intellectual property and other rights in or to the information contained herein and such information may only be used in connection with the operation of your GAI Tronics product or system This manual may not be disclosed in any form in whole or in part directly or indirectly to any third party NOTE A copy of End User s License Agreement for Microsoft Software is attached to this manual and must be strictly observed General Information Product Overview The Model 69254 006 Master Control Unit MCU printed circuit board assembly PCBA is the central component of system operations processing all operations through its associated system software It is installed in the 10457 Card Rack Assembly and maintains constant communication with all other PCBAs in the card rack and the system The MCU constantly supervises operations to ensure proper working condition Application The MCU PCBA 69254 006 is the main control point and communicates with all interface plug in PCBA cards used in your SmartSeries system Each system may include some or all of the following interfac
6. United States this EULA is governed by the laws of the State of Washington If you acquired this EULA in Canada this EULA is governed by the laws of the Province of Ontario Canada Each of the parties hereto irrevocably attorns to the jurisdiction of the courts of the Province of Ontario and further agrees to commence any litigation which may arise hereunder in the courts located in the Judicial District of York Province of Ontario If this EULA was acquired outside the United States then local law may apply Should you have any questions concerning this EULA please contact the Manufacturer
7. barnlenebesdlapebupetabebes siveubenstanubenwenthetey 1 4 Ibs max BACEN e ree Ee eS Dee Drees Dr Prenton ore Der ee 2 42 L x 0 72 W x 0 70 H inches Replacement Part 40005 004 Battery Memory Backup s_eng gtcproddocs standard ioms current release 42004 instr manuals 42004 64912a doc 10 02 ATTACHMENT 1 TO OEM CUSTOMER SUBLICENSE AGREEMENT FOR DEDICATED SYSTEMS END USER LICENSE AGREEMENT FOR MICROSOFT SOFTWARE IMPORTANT READ CAREFULLY This End User License Agreement EULA is a legal agreement between you either an individual or a single entity and the manufacturer Manufacturer of the special purpose computing device SYSTEM you acquired which includes certain Microsoft software product s installed on the SYSTEM SOFTWARE PRODUCT or SOFTWARE The SOFTWARE includes computer software the associated media any printed materials and any online or electronic documentation By installing copying or otherwise using the SOFTWARE you agree to be bound by the terms of this EULA If you do not agree to the terms of this EULA Manufacturer Microsoft Corporation Microsoft and Microsoft Licensing Inc MSLD are unwilling to license the SOFTWARE to you In such event you may not use or copy the SOFTWARE and you should promptly contact Manufacturer for Instructions on return of the unused product s for a refund SOFTWARE LICENSE The SOFTWARE is protected by copyright laws and international
8. eck that the battery connection of the MCU is connected to J13 MCU stay current after a period of battery may need to be replaced Refer to the Battery Replacement system power interruption section Specifications Electrical Power Requirements ceeceeesssecesssseeeeessseeeeesseeeeeesaes 5 V de 12 V dc 12 V dc from backplane CURFENU Dra Wsha a a a a a E Pe Madees babehioe ae 1 75 A 5 V dc 10 mA 12 V dc 10 mA 12 V dc Connections 5525 05 5 4 sco sctocesssetosesosstssesssetraenssisrasnssisipreesti PrE EE oE O Er meee 2 x 64 pin DIN connectors INpUtS OULPUTS cerirrsrnesiiiieiiie niiae E ECEE EE One serial port RS232 DB 9P Support for eee One parallel port Centronics bi directional keyboard AT compatible and one 10BaseT Ethernet RJ 45 connection LED Indicators Green a cave cate teva cada tude cede tidnsedl sd dude cucvcu cues duenccetecerdces AERE 5 V 12 V 12 V CONTO LS enin apa owed emai EE E ENE wean EENE EE ENE E NE OEE CPU Reset Batte teener aee che ced Bhs ceo Boe eie ie cove EE cbse race Sede OEA EO E AR Lithium 1 9 A H 3 6 V Environmental Temperature Range Operating Storage seesesseseererssssssesrresssssssee 32 F to 120 F 0 C to 49 C HU d YEE E E TEE O A N 5 85 non condensing relative humidity Mechanical Unit Dimensions aeresereseseicciccie 10 30 H x 1 625 W x 9 07 D inches 262 x 41 3 x 230 4 mm Unit We1ght c si scctitasetebitateds Mas eaeatnaehenntasesentenpebatnbena
9. elcro to seat 9 Secure the battery pack using a similar type of tie wrap 10 Route the battery cable under the printed circuit board Refer to Figure 1 11 Connect the battery cable to J13 The connector is polarized to ensure the correct polarity 12 Find the MCU s original slot located on the farthest left side of the card rack Align the MCU into the upper and lower tracks for the slot 13 Reconnect the RJ 45 connector to the Ethernet PCBA Refer to Figure 1 Slide the MCU card toward the rear of the card rack until it comes in contact with the connector on the backplane Use caution to avoid pinching the Ethernet cable 14 Firmly press on the front bezel until the MCU is seated in the connectors and tighten the 2 screws located on the front bezel to secure it to the card rack 15 Reapply power to card rack Update the time and date settings using the Talk2MCU application Refer to GAI Tronics Pub 42004 625L2 Talk2MCU User s Manual for instructions s_eng gtcproddocs standard ioms current release 42004 instr manuals 42004 64912a doc 10 02 Pub 42004 649L2A 69254 006 MCU PCBA PAGE 6 OF 10 Troubleshooting The LEDs on the front bezel Check to insure that the MCU is inserted correctly into the card rack do not illuminate Check that power is applied to the associated card rack Call for service of the MCU and or card rack System does not boot up Call for service of the MCU Date and time settings do not Ch
10. er an interruption of system power occurs Refer to the Battery Pack Replacement section s_eng gtcproddocs standard ioms current release 42004 instr manuals 42004 64912a doc 10 02 Pub 42004 649L2A 69254 006 MCU PCBA PAGE 5 OF 10 Maintenance Warnings Please observe the following warnings or damage to the equipment may result N WARNING aS Disconnect power to the card rack before performing any maintenance A Warning Observe precautions for handling electrostatic sensitive devices Battery Pack Replacement A CAUTION A Proper replacement of the battery pack when needed is critical to the operation of the system therefore only skilled technicians should perform this task A screw driver is required to replace the battery pack when necessary 1 Verify that power to the card rack is disconnected 2 Identify the correct location in the card rack The bezel is labeled MCU The PCBA card is located on the left side of the card rack 3 Remove the 2 screws that secure the MCU to the card rack located at the top and bottom of the bezel 4 Remove the MCU from the card rack slowly using the ejection tabs on the bezel and remove the RJ 45 connector from the Ethernet PCBA 5 Cut the tie wrap that secures the battery to the board during shipment Refer to Figure 1 6 Remove the battery connector at J13 7 Remove the battery pack that is held in place by Velcro 8 Install the new pack Press firmly to allow the V
11. es Page Party Interface Access Panel Interface Amplifier Zone Interface and Audio Generator Interface The MCU contains a high density read write solid state disk SSD DiskOnChip The SSD device operates as a normal bootable hard disk drive and holds the system software as well as the system configuration files The MCU provides a Serial Output Port COM2 The unit also supports a keyboard interface AT compatible one parallel port and a 10BaseT Ethernet LAN port located on the rear of the card rack assembly System Requirements and Limitations The 69254 006 Master Control Unit is exclusively designed for use in a SmartSeries system This assembly is not intended for use with other types of equipment GAI Tronics Corporation P O Box 1060 Reading PA 19607 1060 USA 610 777 1374 800 492 1212 Mm Fax 610 796 5954 VISIT WWW GAI TRONICS COM FOR PRODUCT LITERATURE AND MANUALS Pub 42004 649L2A 69254 006 MCU PCBA PAGE 2 OF 10 f JUMPER JUMPER Faji TSN Pa CONFIGURATION CONFIGURATION a JUMPER CONFIGURATION wi ETHERNET CABLE ETHERNET CONNECTION BOARD MODE SWITCHES S2 amp 3 MODE SELECT uo HI ela L m CRETTI ELTETT 10
12. he two screws located on the front bezel to secure it to the card rack s_eng gtcproddocs standard ioms current release 42004 instr manuals 42004 64912a doc 10 02 Pub 42004 649L2A 69254 006 MCU PCBA PAGE 4 OF 10 Operation After the MCU has been installed into the card rack reconnect the power There are three LEDs on the front bezel that indicate if power is on They are 5 V 12 V and 12 V The green LEDs light when the voltages are present A manual reset button is located on the front bezel of the MCU A slot labeled CPU RESET allows the operator to manually reset the CPU See the system manual prepared for the custom equipment to learn how the MCU operates in your unique system The MCU s behavior for your system is controlled by a unique software configuration The software configuration is transferred from another computer to the MCU by running the Talk2MCU application The Talk2MCU application is also used to set the date and time on the MCU The MCU uses the Microsoft DOS operating system during system startup to allow communication with Talk2MCU The Microsoft license agreement is included at the back of this manual Once the system is started the MCU uses another operating system and MS DOS is no longer in use The internal memory back up battery pack located on the MCU PCBA will require replacement when the wrong date and time are displayed on the logging printer printouts or on the access panels VFD display aft
13. instructions for each unit of Upgrade SOFTWARE you install If the SOFTWARE is provided by Manufacturer on separate media and labeled as Recovery Media you may not make a copy of the SOFTWARE as described in Section 1 for archival purposes Instead you may use the Recovery Media solely to restore or reinstall the same version and language release of the reinstalled in accordance with Section 1 of this EULA A single unit of Recovery Media may be used by you to restore or reinstall the SOFTWARE on ADDITIONAL SYSTEMS COPYRIGHT All title and copyrights in and to the SOFTWARE including but not limited to any images photographs animations video audio music text and applets incorporated into the SOFTWARE the accompanying printed materials and any copies of the SOFTWARE are owned by Microsoft MSLI or their suppliers You may not copy the printed materials accompanying the SOFTWARE All rights not specifically granted under this EULA are reserved by Microsoft and MSLI Page 3 of 4 PRODUCT SUPPORT Product support for the SOFTWARE is not provided by Microsoft or its subsidiaries For product support please refer to Manufacturer s support number provided in the documentation for the SYSTEM Should you have any questions concerning this EULA or if you desire to contact Manufacturer for any other reason please refer to the address provided in the documentation for the SYSTEM LIMITED WARRANTY Limited Warranty Manufacture
14. itation e Single SYSTEM The SOFTWARE is licensed with the SYSTEM as a single integrated product The SOFTWARE may only be used with the SYSTEM e Rental You may not rent or lease the SOFTWARE Page 2 of 4 Software Transfer You may permanently transfer all your rights under this EULA only as part of a sale or transfer of the SYSTEM provided you retain no copies you transfer all the SOFTWARE including all component parts the media any upgrades or backup copies and this EULA and if applicable the Certificate s of Authenticity and the recipient agrees to the terms of this EULA If the SOFTWARE is an upgrade any transfer must include all prior versions of the SOFTWARE Termination Without prejudice to any other rights Manufacturer Microsoft or MSLI may terminate this EULA if you fail to comply with the terms and conditions of this EULA In such event you must destroy all copies of the SOFTWARE and all of its components parts Single EULA The package for the SOFTWARE may contain multiple versions of this EULA such as multiple translations and or multiple media versions e g in the user documentation and in the software In this case you are only licensed to use one 1 copy of the SOFTWARE PRODUCT Export Restrictions You agree that you will not export or re export the SOFTWARE to any country person entity or end user subject to U S export restrictions You specifically agree not to export or re export the SOFTWARE i t
15. o any country to which the U S has embargoed or restricted the export of goods or services which currently include but are not necessarily limited to Cuba Iran Iraq Libya North Korea Sudan and Syria or to any national of any such country wherever located who intends to transmit or transport the products back to such country ii to an end user you know or have reason to know will utilize the SOFTWARE in the design development or production of nuclear chemical or biological weapons or iii to any end user who has been prohibited from participating in U S export transactions by any federal agency of the U S government UPGRADES AND RECOVERY MEDIA If the SOFTWARE is provided by Manufacturer on media separate from the SYSTEM and is labeled For Upgrade Purposes Only Upgrade SOFTWARE you may install one copy of the Upgrade SOFTWARE onto the SYSTEM as a replacement copy for the SOFTWARE originally installed on the SYSTEM and use it in accordance with Section 1 of this EULA You may also install additional copies of the Upgrade SOFTWARE as replacement copies onto additional SYSTEMS which are the same brand and model as the SYSTEM and contain a duly licensed copy of the same version and language release of the SOFTWARE ADDITIONAL SYSTEMS provided that 1 Manufacturer has supplied a corresponding serialized sticker for each additional copy of the Upgrade SOFTWARE and 2 you affix a serialized sticker per Manufacturer s
16. r warrants that the SOFTWARE will perform substantially in accordance with the accompanying written materials for a period of ninety 90 days from the date of receipt Any implied warranties on the SOFTWARE are limited to ninety 90 days Some states jurisdictions do not allow limitations on durations of an implied warranty so the above limitation may not apply to you Customer Remedies Manufacturer s and its suppliers entire liability and your exclusive remedy shall be at Manufacturer s option either a return of the price paid or b repair or replacement of the SOFTWARE that does not meet the above Limited Warranty and which is returned to Manufacturer with a copy of your receipt This Limited Warranty is void if failure of the SOFTWARE has resulted from accident abuse or misapplication Any replacement SOFTWARE will be warranted for the remainder of the original warranty period of thirty 30 days whichever is longer No Other Warranties EXCEPT AS EXPRESSLY PROVIDED IN THE LIMITED WARRANTY SECTION ABOVE THE SOFTWARE IS PROVIDED TO THE END USER AS IS WITHOUT WARRANTY OF ANY KIND EITHER EXPRESSED OR IMPLIED INCLUDING BUT NOT LIMITED TO WARRANTIES OF NON INFRINGEMENT MERCHANTABILITY AND OR FITNESS FOR A PARTICULAR PURPOSE THE ENTIRE RISK OF THE QUALITY AND PERFORMANCE OF THE SOFTWARE IS WITH YOU No Liability for Consequential Damages MANUFACTURER OR MANUFACTURER S SUPPLIERS SHALL NOT BE HELD TO ANY LIABILITY FOR
Download Pdf Manuals
Related Search