Operating manual 3B
Contents
1. 5000phone_id Program Intercom Station ID phone_id 0 9999 Factory setting empty 5001 telephone number Program memory M1 for direct dialing button 1 Factory setting empty Note This memory must be programmed as empty memory if automatic dialing is not required M1 is cleared with 5001 5002 telephone number Program memory M2 for direct dialing button 2 Factory setting empty Note Only M1 is dialled if this memory is empty M2 is cleared with 5002 5003 telephone number Program memory M3 for direct dialing button 3 Factory setting empty Note Number chaining ends with memory M2 if memory M3 is empty M3 is cleared with 5003 980factory_settings_ option Return to factory settings Erase Memories factory_settings_option 0 Factory Settings factory_settings_option 1 Factory Settings accesscode and relaycode unchanged factory_settings_option 2 Erase memories M1 M3 amp M100 11 16 5100 pstn_prefix Program memory M100 PSTN_PREFIX Factory setting empty The deletion of M100 is done by 5100 9900 Disconnect 9901 Reactivate loudspeaker Defining Call Procedures Determine the call chosen from the storage places Determine the call chosen from the storage places You determine this setting by programming at least one of the three direct dialing storage places M1 M3 After touching the switch on button and the direct dialing button2. 1100 Set ring signal counter to the value 00 to define automatic call acceptance after the first signal To Define Automatic Call Acceptance after n Rings You can define this call acceptance scenario by setting the programmed ring signal counter 11xx 3 to the desired value within a range of 1 98 Incoming calls will then be acoustically and optically signaled by the station and automatically accepted when the set number of rings signals has been reached Example 1234 Receive programming authorization 1103 Set ring signal counter to the value 3 to set the automatic call acceptance at 3 rings 9 With a programmed ring volume of 1600 the speaker is muted when the call is being signaled To Define Manual Call Acceptance You can define this call acceptance scenario by setting the programmed ring signal counter 11xx 3 to the value 99 Incoming calls will then be acoustically and optically signaled and only accepted when the on off button is pressed Example 1234 Receive programming authorization 1199 Set call counter to the value 99 to shut off automatic call acceptance 9 With a programmed ring volume of 1600 the speaker is muted when the call is being signaled 13 16 Problem handling Unexpected disabling of any communications call call reception You start a call or receive a call and the communication is more or less immediately disabled This prob
3. melody Ringer melody ringer_melody 0 8 Factory setting ringer_melody 7 160ringer_volume Ringer volume ringer_volume 0 7 0 mute Factory setting ringer_volume 6 17t_button_pressed_ before_offhook Duration for which button must be pressed continuously before the Intercom Station goes offhook t button pressed before offhook 00 Immediate t button pressed before offhook 01 99 0 1 seconds Factory setting t button pressed before offhook 00 20t wait user action Time limit for the user actions touch of direct dialing buttons and call answering t wait user action 00 unlimited t wait user action 01 99 seconds Factory setting t wait user action 515 seconds 25t relay on duration Relay activation time t relay on duration 00 unlimited t relay on duration 01 99 seconds Factory setting t relay on duration 02 seconds 2600 relaycode Relay activation code relaycode 0 9999 except 0600 0990 and actual accesscode Factory setting relaycode 1 10 16 3000accesscode Access Code accesscode 0000 9999 except 0600 0990 and actual relaycode Factory setting accesscode 1234 32t_button_pressed_ before_onhook Duration for which button must be pressed continuously for clear down to take place t button pressed before onhook 05 99 0 1 seconds Factory setting t button pressed before onhook 20 2 seconds
4. the communication terminal immediately tries to build up a connection to the partner The action is terminated by the successful realization of the connection or the deactivation of the communication terminal if the programmed time limit 20xx 15 s runs out Example 1234 Getting the permission to program 5001 101 Direct dialing button 1 programm the linked storage button and determine the partner number e g 101 5002 102 Direct dialing button 2 programm the linked storage button and determine the partner number e g 102 5003 103 Direct dialing button 3 programm the linked storage button and determine the partner number e g 103 2015 set time limit e g 15 s to determine how long IntellyCom 3T shall wait if the user touches a direct dialing button and that the called partner accepts the call If the no direct dialing or call acceptance is realised the IntellyCom 3T deactivates itself after the expiry of the chosen time limit Defining Call Acceptance Procedures To Define Automatic Mute Call Acceptance with the First Ring Signal You can define this call acceptance scenario by setting the programmed ring signal counter 11xx 3 at the value 00 Incoming calls to the station will then be signaled optically and accepted automatically with the first signal In contrast to the other call acceptance scenarios the speaker and the microphone are muted 12 16 Example 1234 Receive programming authorization
5. 0 C to 70 C Other features Call volume 7 levels and silent Maximum approx 80 dB A at a distance of 1 m at 50 VAC 50Hz Call melodies 9 melodies Minimum call duration until automatically engaged 2 800 ms without interruption call diversion not permitted Call pause duration for call pause bypass 2 6s Speaker Maximum volume approx 68 dB A at a distance of 1m Volume 7 levels Directives and regulations Conformity with the following directives and regulations R amp TTE directive 1999 5 EC Low voltage directive 73 23 EEC EMC directive 89 336 EEC for residential and industrial zones 15 16 Subject to alterations Or errors Ig 71 37 FUNKE HUSTER FERNSIG 1 FHF Funke Huster Fernsig GmbH Gewerbeallee 15 19 D 45478 M lheim an der Ruhr Phone 49 208 82 68 0 Fax 49 208 82 68 286 http www fhf de e mail info fhf de
6. Weatherproof Intercom Station Intelly om 3T la Lil ID FUNKE HUSTER FERNSIG FHF BA5228 3 02 12 Operating Manual IntellyCom 3T Notes Please read the operating manual carefully before installing the device Texts and illustrations have been compiled and software created with the utmost care however errors cannot be completely ruled out This documentation is therefore supplied under exclusion of any liability or warranty of suitability for specific purposes FHF reserves the right to improve or modify this documentation without prior notice Before opening or dismounting the device it has to be separated from all voltage supply General Description The IntellyCom 3T is a weatherproof Intercom Station which can be operated in the analogue public telephone network or can be connected to analogue terminals of branch exchanges The IntellyCom 3T is available in different designs e With casing it is made for wall mounting or it can be fixed on pylons and joists e Without casing it is meant as built in unit This manual describes below the construction with casing The connection of the built in unit is made correspondingly but without considering the cable entries The Intercom Station comprises a loudspeaker and a microphone for voice communication a hookswitch key as operating element three key buttons for direct dialing and a LED part of the hookswitch key as loop current indica
7. h on button and successively one of the direct dialing buttons to release a connection to the chosen partner The loop current indicator light blinks to indicate that a connection is being made and changes to the continuous on state when the receiving party answers the call To converse with your respondent speak in the direction of the Intercom station from a distance of about 30 cm To disconnect press the on off button and release when a signal tone announces the expiration of the programmed minimum press duration 32xx 2 s The loop current indicator light will go out and the intercom station will go back to standby Receiving a Call When the intercom station rings press the on off button The loop current indicator light goes on glowing continuously Conduct your conversation To disconnect press the on off button as above under Making a Call The loop current indicator light will go out and the intercom station will go back to standby 7 16 Programming The Intercom Station IntellyCom 3T is designed to be programmed remotely over the telephone line Programming is carried out using sequences keyed from a telephone when connected to the IntellyCom 3T to be programmed Remote programming codes are split into two classes Class 0 and Class 1 which are distinguished by different enclosing characters for Class 0 and for Class 1 The IntellyCom 3T accepts Class 1 programming codes only if the user ha
8. k schema 24 ringback 2 Ring back schema 246 Delivery condition ringback 1 Ring back schema 24 11number of rings Number of rings before automatic answer number of rings 00 Automatic answer without ringing Microphone and Speaker muted number of rings 01 98 Automatic answer with ringing number of rings 99 No automatic answer Factory setting number of rings 03 12t max call duration Maximum call duration Length of conversation before automatic clear down t max call duration 00 No limit t max call duration 01 99 minutes Factory setting t max call duration 00 43t duration of silence before cleardown Duration of silence before automatic cleardown t duration of silence before cleardown 00 Does not clear down on duration of silence t duration of silence before cleardown 01 99 seconds Factory setting t duration of silence before cleardown 28 seconds 140speaker volume Loudspeaker volume speaker volume 0 7 0 mute Factory setting speaker volume 7 9 16 142duplex profile Set up duplex profile of voice communication duplex profile 0 4 full duplex semi duplex Delivery condition duplex profile 0 full duplex Remark In case of inappropriate electrical and or acoustic installation conditions co coupling effects whistler may occur In those cases modify the regulation of the profile in to the higher values semi duplex 150ringer
9. lem may occur if the IntellyCom or set of your interlocutor is installed in a noisy environment If those ambient noises hit the busy tone schema of the IntellyCom it considers the connection as disabled by the interlocutor and switches off You can switch off the operation mode disable in case of busy tone by setting the option 101x 0 to the value 1 Please note that in a noisy environment the operation mode Disable in case of continuous silence 13xx 28 s will also be affected To guarantee an automatic disabling of the IntellyCom the maximum call duration which in the delivery condition is adjusted to infinite 12xx 0 infinite should be limited to a convenient value Example 1234 Obtain the programming authorization 1011 Set option disable in case of busy tone to the value 1 to deactivate the disabling in case of identified busy tone 1205 Determine the maximum call duration to e g 5 min to guarantee that the IntellyCom switches off automatically Unexpected muting at the beginning of outgoing communications call You start a call your interlocutor answers the call and does not hear you at the beginning This problem may occur of the IntellyCom does not understand the message of your interlocutor and continues the supervision of the calling phase with muted microphone and flashing loop current display You can manually stop the muting function by a short activation of the activation button and o
10. m communication terminal remains occupied and waits for a new touch of a direct dialing button The intercom station disconnects automatically when you and your speaking partner pause for longer than the programmed pause limit 13xx when your speaking partner hangs up and IntellyCom 3T detects the telephone s busy signal or when the programmed conversation duration limit 12xx has expired The intercom station mutes the microphone or undoes a previous muting if the on off button is pressed briefly during the conversation IntellyCom 3T s loop current indicator light displays a blinking light to indicate that the microphone is switched to mute or a continuous light to indicate the active state Attention To guarantee the protection against contact a voltage equalizing cable has to be connected to the voltage equalizing screw of the casing or in case of the built in unit to the corresponding mounting tab on the inside of the built in unit The IntellyCom 3T complies with the casing design of the casing kind of protection IP66 For the built in version the installer has to take care that the desired protection against water and dust will be achieved by appropriate seals In case of deficient built ins the installer assumes the entire responsibility For the casing construction the distance to other live components has to be constructed safely in built in condition see EN 60950 1 6 16 Operation Making a Call Touch the switc
11. r by selecting that IntellyCom ring back schema which is able to distinguish earliest language and ring back tones A reliable identification of the call begin cannot be guaranteed with none of the ring back schemas schema 2 offers the lowest error rate Example 1234 Obtain the programming authorization 1020 Set option Ring back schema to the value 0 to select schema 2 14 16 Connection information Input terminal voltage 24 Voc to 66 Vpc from the telephone connection Power supply current 28 mApc to 100 mApc Call signal voltage 35 Vac to 90 Vac 23 54 Hz Call signal impedance Larger 5 5 kW at 25 Hz and 30 90 Vac Larger 4 0 kW at 50 Hz and 30 90 Vac Dialling method Dual tone multi frequency signalling DTMF Pip tone dialling pip tone interval ratio 1 5 1 or 2 1 Connecting terminals Max 2 5 mm Max 30Vac Max 60Vpc Relay contact points Max 1 Aer Max 30 W Max 30Vac Tamper contact Max 60Voc Max 30 W Dimensions With casing Built in unit Material VA Front Panel VA Height x Breadth x Depth Approx 205 x 110 x 60 mm Approx 205 x 110 x 55 mm Weight Approx 1 2 kg Approx 0 65 kg Scanner Metal scanner made of VA with integrated red LED Environmental conditions With casing Built in unit Protection type IP 66 as per EN60529 IP 66 frontal Operating temperature 40 C to 60 C Storage temperature 4
12. s must be screwed in either side diagonally with 1 4 Nm each Connection of the tamper alarm switch Pull the control line through the cable gland of the box and connect the two wires to the insulated screw joints of the tamper alarm switch The voltage and the maximum power in the tamper alarm circuit shall not exceed 60 Vpc or 30 Vac respectively 30 W O O Terminal SE tamper Connection SE alarm Points TCP ols TCP 2 Relay DS contact O19 Connection of the telephone line Pull the telephone line through the cable gland of the box and connect it to the Terminal Connection Points TCP 5 16 Relay contact output The Intercom Station board comprises a relay contact which can be activated from a remote telephone or telephone system This relay can control for example electric door entry mechanism signaling and other electrical devices The voltage at the relay contact terminals shall not exceed 60 Vpc or 30 Vac The maximum power is 30 W The maximum current is 1 A Another cable gland is needed to connect a cable to the relay contacts Exchange it with the sealing plug The operating of the relay is described below In all cases the relay will be deactivated on hanging up Note If the switch on button an the chosen direct dialing button will be touch successively IntellyCom 3T dials the programmed number or sends a short signal that the storage space of the touched button is empty In the last case the Interco
13. s the right to program This is achieved by sending the Class 0 programming code AccessCode The factory setting is AccessCode 1234 Class 0 programming codes are always accepted Programming Codes For each programming sequence below the telephone responds with an acknowledge or an error tone In case of an error tone the programming sequence has to be repeated Class 0 Programming Codes Code Function accesscode Request the programming rights Factory setting accesscode 1234 The corresponding programming function refuses the values 0600 and 0990 and responds with an error tone relaycode Activate relay Factory setting relaycode 1 The corresponding programming function refuses the values 0600 and 0990 and responds with an error tone 0600 Request phone_ID 0990 Cleardown Deactivate relay Class 1 Programming Codes Code Function 100dialmode Select dial mode dialmode 1 Tone dialing DTMF dialmode 2 Pulse dialing 1 5 1 dialmode 3 Pulse dialing 2 1 Factory setting dialmode 1 Tone dialing DTMF 8 16 101disablebusy Set up option Disable in case of busy tone disablebusy 0 Disable in case of busy tone activated disablebusy 1 Disable in case of busy tone deactivated Delivery condition disablebusy 0 Disable in case of busy tone activated 102ringback Set up option Ring back schema ringback 0 Ring back schema 2 ringback 1 Ring bac
14. ting element Utilization and programming is identical in all devices Features Pulse tone dialing Automativ cleardown capability Automatic answering capability or answering after a programmable number of rings Choice of up to three programmable direct dialing numbers Remote programming of e telephone number e ringer volume ringer melody e loudspeaker volume automatic call acceptance e dialing type 2 16 Intercom Station IntellyCom 3T with casing 110 96 IntellyCom 3T N p lle Loudspeaker 205 191 Microphone Loop Current o Oo O Indicator Hook switch FHF Funke Huster Femeig 0 key 60 3 16 Intercom Station IntellyCom 3T built in unit assembly cut out 96 thread M4 or 4 3 mm 4 16 Connection Opening the Intercom Station To gain access to the circuit board or the tamper alarm switch unfasten the four screws in the front panel Attention Before opening or dismounting the device it has to be separated from all voltage supply Concluding notes CE cable entry M20 x 1 5 Protection rating CE IP66 Connection cable 5 to 9 mm Wire and connector diameter 0 14 to 2 5 mm Only appropriate tools may be used for the assembly of the CE The cable connection is suitable for firmly secured conduits only When locking the equipment ensure tight fit and cleanliness of all sealing To retain the protection rating IP 66 cover screw
Download Pdf Manuals
Related Search