OWNER`S MANUAL
Contents
1. installation of Soffit Brackets Drill 1 4 Holes 2 Places c o 3 8 x 4 Lag Screws 2 Places ROOF MOUNT Please contact Awntech at 800 203 7049 regarding this type of installation ATTACHING AWNING BRACKETS THE AWNING MUST BE COMPLETELY CLOSED AND SECURED FOR INSTALLATION CAUTION Secure the awning closed by wrapping several layers of masking or duct tape around cassette including the front of bar and valance You will then remove it once the awning is installed This will prevent the unit from inadvertently opening while being lifted into the brackets When removing the tape from the awning take care not to damage the fabric or scratch the metal With the help of an assistant lift the awning to the brackets on the wall and slip the torsion bar back bar into the brackets Make sure the torsion bar slides all the way to the back of the bracket Then slide the retaining screws into the brackets Center the unit as needed then secure the retaining screws with nuts and tighten If the torsion bar does not easily slip into the brackets lift slightly on the front bar while supporting the torsion bar You may need to loosen the brackets slightly to accomplish this fit CAUTION Never attempt to repair or disassemble the lateral extension arms The lateral arms that support your awning are under great tension and can cause injury The arms also have extremely heavy tension Heavy2. Orporarion OWNER S MANUAL BEAUTY MARK Retractable Awnings DESTIN MAUI GALVESTON Manual and Motorized ASSEMBLY amp INSTALLATION INSTRUCTIONS STEP BY STEP ASSEMBLY AND INSTALLATION INSTRUCTIONS VERY IMPORTANT Choose a wall area that attracts marginal wind force and has at least three layers of brick above where the awning will be installed or at least 12 from the top beam of the wall frame for weatherboard or concrete walls Please read instructions completely prior to attempting installation Damage to awning during the installation is not covered by the warranty After reading should you feel further assistance is necessary please contact the dealer or retailer you purchased the awning from or a local contractor for professional installation INCLUDED PARTS Beauty Mark Awning completely assembled Mounting Brackets with Lag Screws e Hand Crank Remote Control with motorized units Screws nuts and washers for securing the awning to the bracket User s Manual Il REQUIRED ITEMS Drill 1 4 masonry bit for drilling through stucco brick or concrete or 1 4 Wood bit for pilot hole for 3 8 masonry anchor 2 Ladders e Stud Finder e Ratchet with 9 16 socket amp V2 socket e Level or 4 would be best or string level Tape Measure Allen Wrench 3 8 Roll of duct or masking tape Pencil Marker or Chalk Phillip s Head Screwdriver e Anchors f
3. arms This means rain will puddle on the awning and make the awning much heavier However if you think you will enjoy sitting under your awning in the rain you may request we install front panel grommets so rain has a place to run off If you do not put grommets in the front panels do not use retractable awnings in the rain SELLING POINTS WHY BUY High quality low cost easy to install energy cost savings 5 year warranty enhances the value of the property appearance designer appeal weather protection family skin protection interior furniture protection meets UBC requirements easy to remove and store can purchase replacement covers in various colors WHO BUYS Homeowners home renters business owners property developers builders property renovators interior designers remodelers architects federal state local government departments customers desiring energy savings etc BENEFITS Weather protection energy savings and protection of furniture from sun s harmful rays visual appearance enhancement COST JUSTIFICATION Many customers have asked why our awnings are so much less expensive than the others on the market The answer is that it has been our main objective since we started business in 1983 to make awnings affordable without lowering quality so people can buy them Our awnings cost 1 3 to 1 2 of the cost of other awnings available on the market Our patented frame systems are responsible for this The frame q
4. winds snow or ice are not considered defects We offer replacements at affordable prices CLEANING amp CARING Beauty Mark Awnings should be cleaned at least once a year in low maintenance areas and twice a year in high maintenance areas see high maintenance areas above Cleaning consists of brushing off debris with a broom brushing on a non detergent cleaning compound such as Y vinegar 2 water letting it sit for 20 minutes and rinsing Regular maintenance generally means a once a year cleaning with additional care if stains or soil appear Also remember that your awning is an exterior product In the same way you wouldn t leave your automobile outside without washing it for very long you ll also need to clean your Beauty Mark awning to preserve and extend its beauty and life Please refer to the Cleaning and Care chart below if you acquire a stain from one of the ingredients on the list CLEANING amp CARE CHART BERRIES BLOOD DRIED BUTTER CHARCOAL PENCIL MARKS CATSUP OR MUSTARD CHEWING GUM CHOCOLATE COFFEE COLA CRAYON EGG RAW GRAPE J UI CE GRAVY GREASE CAR INK PERMANENT I NDIA BALLPOI NT IRON RUST LIPSTICK MASCARA MILDEW MILK NAIL POLISH OIL ORANGE DRI NK PAINT LATEX WET PAINT LATEX DRIED PAI NT OI L OR LACQUER SHOE POLI SH LI QUI D SHOE POLI SH WAX SUNTAN LOTI ON TEA TOMATO JUI CE TREE SAP TER COLOR WAX CANDLE WINE Liquid detergent ammoni
5. Pow er n a 230 Current Intensity n a 2 441 24 Normal Speed n a 13 r min Rated Torque n a 3 nm Intermittent Running ana ep tite Time Ingress Protection n a IP44 Insulation Class n a 1 Work Temperature n a 15c to 85c AC Pow er Rated Load ie More than 600 Remote Control Voltage n a AC 110V 120y Frequency His Output Pow er n a 315MHZ Distance n a 50 meters Work Temperature n a 15c to 85c AC Power ao nis No More than 600 Shipping LTL LTL thod Light TruckCurbside Light Truck Curbside Installation Time Within 30 Minutes Within 30 Minutes Persons Required 2 2 Electric Hamner Shock Drill Level Wrenches Tools Power socket near position of installation for motorized Diagram Remote Control Note Open amp Close Positions are Reversed far Left Matar Applications Diagram 3 Motor Crank View WIND SENSOR ACCESSORIES 2 BRACKETS HOOD ADJUSTABLE PITCH CRANKS LEG SUPPORTS SCREEN ROOM ROOF BRACKETS SOFFIT BRACKETS ADJUSTABLE PITCH CRANK HOOD 42 OTHER DRAWINGS Diagram Exploded View of Awning Diagram H Installed View of Awning Frequently Asked Questions 1 What is the difference between Maui Manual and Maui Motorized Retractable Awnings The Maui Manual Awning is manually operated They open easily in less than a minute using a hand cranked gear mechanism no electricity required One person can operate it wit
6. a 3 6 water Detergent ammonia 3 696 water Acetone Vacuum then liquid detergent Liquid detergent Acetone Liquid detergent ammonia water Detergent white vinegar Acetone Liquid detergent Paint oil or grease remover Liquid detergent Liquid detergent Liquid detergent Acetone Paint remover Acetone detergent Oxalic or citrus acids water Paint oil or grease remover Paint remover Acetone detergent water 1 of bleach and 1 4 cup mild soap per gallon water Liquid detergent Acetone Acetone Liquid detergent water Liquid detergent water Paint oil or grease remover Paint oil or grease remover Acetone Apply heated iron over towel Acetone Pine Power or pine oil detergent Liquid detergent Liquid detergent Turpentine liquid detergent Liquid detergent water white vinegar Apply heated iron over towel Acetone Liquid detergent ammonia 3 6 water white vinegar RETURNS DAMAGES RETURN QUALIFICATION You may return the product if it is reported defective upon arrival If you change your mind after purchasing you will be given merchandise credit only DAMAGED MATERIAL Damage to the packaging occasionally occurs during shipping Scrapes dents and rips in the outer packaging that could indicate possible damage should be described to the carrier at the time of delivery If damage to the product seems apparent the shipment should be refused WRONG COLOR You may receive an awnin
7. distance may vary depending on awning width and stud locations Once you have located the first stud drill a series of small holes to determine the outer edges and the center of the stud Repeat this process for finding the stud on the other end Once you have found the center points of the end studs find the center points of the remaining studs Note The holes may be concealed with filler or caulk after brackets are installed Step 2 Using a bracket as a template center each bracket on the centerline at each of the stud center point locations Then mark the center of each bracket hole with a pencil marker or chalk Drill two pilot holes for each bracket at your marked points Using the supplied bolts securely attach the brackets along the centerline INSTALLING ON BRICK Diag ram C1 Installing Brackets on Brick Surface Determining Placement of Brackets on Brick INSTALLING ANCHORS BRICK amp CONCRETE Diag ram C2 Installing on Brick Concrete Surface Washer 2 Places WOOD 8 STUCCO Diag ram Installing on Wood amp Stucco Surfaces Drill va m oles 2 Places Flat Washer 2 Places 3 B x 4 Horizontal Lag Screws 2 Places SIDING amp METAL BUILDINGS The use of a Backer Board Diagram C4 1 or treated timber beam may be required for vinyl or aluminum siding The 2 10 12 board needs to slightly longer than the awning and attached with anchors not included t
8. duty springs are located inside both left and right arms Serious bodily injury or property damage may occur if you attempt to install without restraining the awning Diag ram Attaching Awning to Brackets ADJUSTING THE PITCH The correct pitch is 1 to 2 per foot of extension projection For an awning with a 10 projection this would 10 to 20 When the awning is fully extended the front bar will be 10 lower than the back bar When lowering the awning pitch fully extend the awning and loosen the Allen screws on one side Get an assistant to hold the front bar at the correct height and then retighten the Allen screws Repeat on the opposite side When raising the awning pitch you will need to retract the unit leaving 1 to 2 extended Loosen all hardware the same way would to lower the unit Slightly lift up on front bar to set your desired pitch then retighten Allen screws Repeat on the opposite side Diagram Pitch Adjustment Mechanism ACCESSORIES 1 MOTOR RECEIVER REMOTE CONTROL WIND SENSOR Powder Costed Steel Pow der Costed Steel Frame Materials amp Aluminum amp Aluminum Fabric Weight 300 gramz meter 300 grams meter Wind Speed Allow ance 46 mph 46 mph Running Time From Full Charge non LE Motor Location n a Left Side Adjustable Pitch Yes Yes i 80 100 lbs 80 100 lbs ht ug Depending size Depending on size Motor Yoltage 14 Frequency n a Input
9. e of home cooler Yes it will keep your deck or patio up to 20 degrees cooler and block harmful UV rays that fade furniture and discolor carpets and flooring By placing an awning on the western side of your home you may save up to 30 on air conditioning bills during the summer months By keeping the awning retracted during winter months you allow the sun to warm your home and save on heating costs 15 What are the frame and cover made of FRAME Powder coated structural steel amp anodized structural aluminum frame PARTS CONNECTORS amp HARDWARE Structural weather resistant UV treated nylon amp aluminum connectors Structural anodized aluminum and powder coated steel parts Stainless steel hardware COVER MATERIALS 5 Year Warranty Fabric weight 300 grams sq meter 600 Denier X 600 Denier 100 Solution Dyed Acrylic or Polyester Full dye sublimation both sides of fabric with UV and polyurethane coatings Life expectancy is 5 10 years 16 What tools are required to install and how many installers are needed TOOLS REQUIRED Drill Impact Drill for Masonry or Concrete Walls e Mallet Level e Tape Measure e Two Ladders Pencil or Chalk e Two people 17 What is the life expectancy of my awning LIFE EXPECTANCY Awntech s Warranty is for 5 years and with proper care and maintenance it can last up to 10 years 18 What is the maximum wind speed that the awning can sustain when extended Is there an aut
10. f you have questions about this please contact us at 800 203 7049 DAMAGE DUE TO IMPROPER ANCHORING STRONG WINDS SNOW OR ICE Awntech Corporation does not guarantee its retractable awnings against damage that is weather related such as strong winds snow and ice under any circumstances These awnings are designed to protect the customer from the sun and UV rays They are not designed to hold snow loads ice loads water pooling loads or loads from debris such as leaves and falling branches If your awning is not anchored securely it will lift Retractable awnings make excellent kites If your awning starts to lift we are not responsible and will not send free replacements Anchoring is your responsibility We only offer fasteners for brick mortar or concrete mounting It is the best to be safe rather than sorry This means that the best maintenance practice is to keep your awning retracted until you are ready to use it Then retract it when you are finished If you know that a strong weather front is coming retract the awning CLEANING amp CARING NORMAL WEAR amp TEAR Certain regions of the country are extremely hard on awnings of any kind If you live in these areas High Maintenance Areas Florida Texas New Mexico Arizona Nevada or high altitude areas you probably already know how the sun can take a toll Normal wear and tear is not covered in our warranty and should be expected Damages caused by improper anchoring strong
11. g fabric cover that may be a slightly different shade than the colors seen on the Web We warn customers ahead of time that actual fabric colors may appear slightly different than web graphics We do not replace covers in this case You may purchase a new cover for 50 of the price of the awning at the going market rate WRONG SIZE Advise the customer to measure the area where they intend to install the awnings Please make sure that you have at least 1 2 extra wide area available to install the awning and also make sure that you have enough open space for the projection The customer should measure the minimum height requirement of 8 from the ground for any retractable awning before they place the order RETURNS ORDER EXCEPTION CONTACT Customer Service Awntech Corporation 10701 Tube Drive Hurst TX 76053 Phone 817 857 9532 fax 817 857 9535 email CUSTOMERSQAWNTECH COM Authorized returns should be shipped to Customer Service Awntech Corporation 10701 Tube Drive Hurst TX 76053
12. h ease The Maui Motorized Retractable Awning has a manual override motor and an inside remote control that opens and closes the awning with the touch of a button You plug it into a grounded electrical outlet The motor is hidden in the roller bar 2 Which of the Beauty Mark retractable awning models is right for me The width of your patio area dictates the size of the awning A motorized awning provides the convenience of easy operation with a touch of a button A manually operated crank Is easy to use and 15 less expensive than a motorized model If you choose a motorized awning you will need to determine where your outlet is before ordering You may purchase your awning with the motor on either the left or right side Left or right side is determined by knowing which side you want your cord plug to be on left or right if facing the awning from the front 3 How easy is it to install the awning You don t have to be a handyman or a person with a lot of experience using tools You will need to have an electric drill and the proper drill bits for your particular wall surface and hardware There are 2 steps involved 1 Install the brackets 2 Slide awning into brackets and secure This job will require 1 person to install the brackets and 2 people to lift the awning into the brackets and secure them Your awning comes with a Step by step instruction manual If you need further assistance you can reach the Awntech Customer Service Depart
13. ing the bottom of the valance Keep in mind that your awning has an adjustable pitch mechanism to block the sun at different angles So if your awning placement is not limited by low eaves you may want to mount the top of your awning as high as 10 from the ground to allow for various pitches Diagram A4 The front bar height of your awning will determine the location of the rear mounting brackets The ideal mount height top of awning is 8 for low eaves applications and 9 10 for all other applications Diagram 1 Diagram A1 Determining Mount Height HOW TO MEASURE RETRACTABLE AWNINGS AWNING WIDTH v i N Diagram A2 Determining Mount Height A Minimum 76 Minimum Mounting Height 9 Projection Example of 9 Mounting Height DETERMINING BRACKET PLACEMENT The recommended pitch for awnings is between 1 to 2 inches per foot of projection Diagram A4 Example for 10 ft projection your optimum installation height of brackets on center should be between 8 and 9 A minimum of 6 6 is the lowest mounting height recommended Less than this could cause head injury due to low height of front bar In standard applications please allow a 2 clearance between the top of the awning and the roof overhang Also allow 1 additional on either side of the awning if you are mounting it under an overhang Note If you pati
14. k Fabrics are sealed with polyurethane coatings in the manufacturing process and seams are sealed before they leave the factory Awntech retractable awnings have grommet holes near the front bar as an additional feature to allow water to drain from areas that tend to puddle 11 Can install the awning on vinyl or aluminum siding stucco or on masonry Yes The easiest way is to mount a 1 x 4 treated painted timber beam the same length as your awning width through the siding into the studs Then you mount the awning to the timber beam You will need to paint the beam the same color as your house or trim so it will blend in nicely with your siding or trim 12 Do have to take down my awning and store it over the winter No Just close the awning and leave it up all year long Our fabric has been designed to withstand the elements year round You may also purchase additional accessories such as a hood stops birds from nesting on your awning weather cover for winter storage wind support legs and screen room for your awning by calling 800 200 5997 or visiting us online at www awntech com 13 Is the awning fabric easy to clean Yes Just follow the guidelines listed in our cleaning chart above if you want to clean the awning cover while it is attached to the awning frame Awning covers can also be removed and cleaned Please call us at 800 203 7049 for step by step instructions on this process 14 Will this awning help keep the insid
15. ment from 8 00am to 5 00pm CST by calling 800 203 7049 An installation expert will be able to guide you through installation process if you have questions 4 Can install a retractable awning on a house with low eaves Yes you can install all Beauty Mark retractable awnings on homes with available mounting height ground to eaves as low as 7 ft under eaves overhangs and gutters You will need 10 inches of horizontal area above your patio door The ideal installation height however is 9 10 ft from the ground floor 5 Can this awning be installed on a mobile home or a garage Yes however we do not provide anchors for all types of wall surfaces We provide anchors for brick concrete and stone Anchors for other surfaces may be purchased at your nearest hardware store Please make sure you mention the wall surface and weight of the unit to the hardware representative before purchasing your anchors If you are installing an awning on a home with siding a treated timber beam makes a nice level surface for the installation 6 Why do Beauty Mark awnings cost so much less than other suppliers We sell a large number of awnings with low profit margins Our objective is to provide the highest quality awnings for the lowest possible price so that more people can afford them Please do not conclude that we compromise quality Our awnings have a structural steel torsion bar main structural bar and stainless steel twin arm cables Our fabric
16. o door swings out a minimum of 12 inches of clearance is required above the door This way your door will clear the awning when it has a pitch After the height is determined use your level and draw a straight and level line with your pencil marker or chalk where the awning is to be mounted Draw a line equal to the width of the awning torsion bar back bar This will help you determine the height and placement of the mounting brackets It is IMPORTANT that this line is level It may mean the line might not be parallel with the exterior wall Diagram Determining Bracket Locations Overhang 9 Min Unobstructed wn Mounting Wall Height Brackets TE Mele medoes represent the actual number o brackets required your ay Mini WALL BRACKET INSTALLATION CAUTION Improper installation of mounting brackets may cause awning damage or personal injury The bracket bolts must be secured to a structural stud see Diagram D above The brackets should be secured with lag screws as close to the center of the stud as possible When fully extended the weight of the awning exerts significant torque on torsion bars Failure to center bolts in structural studs will cause premature failure and result in awning collapse and possible injury Step 1 Use a stud finder to locate studs near the ends of the awning along the centerline you have drawn approximately 10 from the ends of the awning This
17. o studs in the wall Then the awning brackets need to be attached directly to the beam It is recommended that the board be treated painted and dried prior to installation Caution should be taken that sufficient size and number of bolts be used to secure the board to your structure Locate the bracket centerlines on the board like earlier steps Secure brackets to the board Then mount board to previously marked studs Make sure it is secured to multiple studs Secure the board along the centerline determined in previous steps Make sure board is secured tightly Continue installation steps as outlined for mounting unit in normal wall mount Another method for installing on siding is to use a shim See Diagram C4 2 below for additional instructions VINYL amp METAL SIDING Diagram C4 1 installing on Vinyl or Metal Siding Mounting to siding Traled beu fixed securely onto sbuds Used kir vir and valle Method 1 Diagram C4 2 installing on Vinyl amp Metal Siding Method 2 amp ROOF MOUNT APPLICATIONS Determine which of the three bracket types you need or your particular application wall soffit or roof Example Not enough wall mount space Use soffit brackets LOCATION AND CENTERING BRACKET ANCHORS ON THE STUDS IS AGAIN THE MOST IMPORTANT PART OF THE INSTALLATION PROCESS EAVES MOUNT Diagram D1 Installation of Soffit Brackets 10 Closed Position Diag ram D2
18. omatic retract for high winds 35mph 19 The catalog specifies either a right or left side motor mount Is this based on looking at the awning as it is mounted on the house e g An awning with right side motor mounted on the South side of the house would have the motor on the East side of the awning If you are facing the awning 20 what is the power source for the motor Is it a regular plug or is hardwired connection What is the amperage required How long is the cord Regular plug 110v 10 ft Cord 21 1 10 clearance needed directly below the awning mount The awning 15 9 high but in certain cases customers are able to have less than 9 clearance You may want to call us at 800 200 5997 if you have a very low roof line 22 is any clearance needed above or to the sides of the awning mount Side clearance above clearance see q 44 above 23 if two 10 awnings were mounted in line to get 20 how much of a gap would there be in the middle About 6 or you can buy 20 awning 24 the awning be partially extended Yes 25 if the motor fails or power drops out perhaps power goes out before wind storm is there a manual retract mechanism Yes our motor very powerful and has a manual override 26 is the motorized awning suitable for a high humidity environment Retractable awnings are primarily sun shade products Retractable awnings have large spans of fabric supported by minimal projection
19. or your particular wall type Required 2 per bracket Contact Awntech Corporation if you need to place an order for additional brackets An Assistant INSTALLING THE BRACKETS DETERMINING HEIGHT AND PLACEMENT OF BRACKETS IS THE MOST CRITICAL STEP IN THE INSTALLATION PROCESS STANDARD WALL BRACKET VS EAVE amp ROOF BRACKETS First you should determine the type of bracket that best fits your architectural requirements If the standard wall bracket that comes with your awning does not fit your application two other choices are available for an extra charge There are eaves brackets for mounting under eaves and roof brackets You need to hire a professional roofer to install the roof brackets if you do not have enough room to mount the awning to the wall If either of these bracket styles is required you may call our Customer Service Department 800 200 5997 to place an order WALL BRACKET SOFFIT BRACKET ROOF BRACKET DETERMINING AWNING PLACEMENT Determining awning placement requires that you measure your available awning area Example If you have low eaves you will be more limited than if you have an open area above your patio door The minimum height clearance of the wall mount area is 10 when closed the awning height is 10 The minimum front bar height from the ground to the front bar Diagram A3 A4 should be at least 6 6 This allows for a tall person to walk under the front bar without their head touch
20. s have been tested to have a 10 year life 7 What type of fabric do you use and how long does it last Beauty Mark fabrics for retractable awnings have a weight of 300 grams meter and are woven with 100 solution dyed acrylic threads and treated with UV polyurethane and mildew resistant coatings What this means to you is that your awning is resistant to fading UVA UVB rays moisture mildew and soil We manufacture our threads and fabrics to have a 10 year life Our awnings come with a 5 year warranty 8 Can leave my awning open all the time Retractable awnings are not built for rough weather conditions We recommend that you retract your awning when you are not using it or purchase our Breeze wind supports and electronic wind rain sensor On average retractable awnings will withstand up to 35mph wind speeds 9 Can I adjust the pitch of the awning Yes you may adjust the pitch of the awning s front bar by as much as 20 degrees All models have an adjustable pitch mechanism on each side of the awning Some models need to be adjusted in the installation process Other models have an adjustable pitch gear and crank If your model did not come with the gear crank mechanism you may order this accessory by calling 800 200 5997 Please see Assembly and Installation Instructions for pitch adjustment details 10 Will my awning leak water in the rain No Beauty Mark Retractable Awnings will not leak water in the rain because Beauty Mar
21. uality is equivalent to custom awnings both commercial and residential The covers are sewn with Beauty Mark SuperStrength monofilament threads The fabric is Beauty Mark 100 solution dyed acrylic with special treatments to resist moisture fading mildew and soil RISKS WARNINGS WARRANTY Please handle with care when you open the package and during assembly and installation The frame parts are made of metal and some parts may have sharp corners Please keep children away during assembly and installation of awnings Warn children about the risks of damage to the awning in rough weather conditions and excessive handling so they do not randomly extend and retract the awning CAUTION Improper installation of mounting brackets may cause awning damage or personal injury The bracket bolts must be secured to a structural stud The brackets should be secured with lag screws as close to the center of the stud as possible When fully extended the weight of the awning exerts significant torque on torsion bars Failure to center bolts in structural studs will cause premature failure and result in awning collapse and possible injury Never attempt to repair or disassemble the lateral extension arms The lateral arms that support your awning are manufactured with structural grade stainless steel cables and high tension arm springs located inside the arms Serious bodily injury or property damage can occur if attempting to install without restraining I
Download Pdf Manuals
Related Search