FN-DA02AH41 - Pro-face America HMI Store
Contents
1. Model 3380701 02 lt Notes gt E Only use the unit installed with other equipment E If the unit is installed in an area with no air conditioning system be sure to install it in a vertical panel using a DIN rail or mounting holes Also be sure the unit is installed so it is at least 100 mm away from any adjacent structures or devices If these requirements are not met the heat gener ated by the unit s internal components may cause the unit to fail to meet UL standards requirements E The power supply unit connected to the Flex Network unit must be a UL c UL approved Class 2 power supply unit or Class 2 transformer When the GLC LT GP3000 or mul tiple Flex Network units under load are operated with a single power supply the amount of current consumption and full load current of the units must be within the rated load of the Class 2 power supply unit or Class 2 power supply transformer Be aware that the number of points which can be turned ON simultaneously may be limited depending on the amount of load and load current value CE Marking Notes The FN DA02AH41 is a CE Marked unit that conforms to EMC EN55011 Class A and EN61000 6 2 directives lt Caution gt While this unit is officially marked as conforming to the relevant EMC directives it is the user s final application of this unit in a larger system i e the machinery wiring control panel installation method etc that will determine if this unit maintains or lo2. DC20 4 to DC28 8V Al D V egies E age 5ms or less Power supply DC24V Interruption In rush Current 15A or less 2 4W or less AC1 000V 10mA 1minute between power Input and Output and FG terminals AC500V 10mA 1minute between primary and secondary power supplies Maor more at DUSU0V between charging and FG terminals AX CAUTION Voltage Endurance Insulation Resistance E Environmental 30 RH to 90 RH non condensing Wet bulb temperature less than 39 C 30 RH to 90 RH non condensing Wet bulb temperature less than 39 C E Output TI Number of 2ch Output Channels up to milliseconds 0 to 10V Impedance min 10KO A 0 to 20mA Impedance 10 to 5009 4 to 20mA Impedance 10 to 5000 Set via terminal connection location Operating Humidity Storage Humidity Output Range urrent Voltage Switchover Accuracy 4 1 FS 0 C to 55 C F Photocoupler Insulation Insulation Method F ree output terminals between internal circuits Conversion Timing No of Exclusive 1 Use Nodes 1 Converted via software 2 This accuracy may not be possible if there is a large amount of noise Ch 1 output voltage terminals 0 0 0 0 A DANGERS e An emergency stop circuit and an interlock circuit should be constructed outside of this unit Constructing these circuits inside this unit may cause a runaway situation system failure or an accident due to unit failure System
3. Flex Network 2 Channel Digital Analog Conversion Unit Installation Guide Thank you for purchasing Pro face s Flex Network 2 Chan nel Digital Analog Conversion Unit FN DA02AH41 To ensure correct use of this unit s functions and features be sure to carefully read both this installation guide and the Flex Net work 2 Channel Analog Unit User Manual The Flex Network 2 Channel Digital Analog Conversion Unit FN DA02AH41 is a CE marked UL c UL listed product Safety Precautions This guide contains a variety of safety markings for safe and correct operation of this unit Please read this installation guide and any related manuals carefully to fully understand how to correctly use this unit s functions E Safety Symbols This guide uses the following symbols for important informa tion related to the safe and correct operation of this unit Please pay attention to these symbols and follow all instructions given Safety symbols and their meanings A hazardous situation that could result in serious injury or even death if instructions are not followed A DANGER A potentially hazardous situation that Z NWARNING could result in serious injury or even death if instructions are not followed A potentially hazardous situation that could result in minor injury or equipment damage if instructions are not followed 2 Specifications E Electrical control section Rated Voltage DC24V Rated Voltage Range
4. es and the power line Otherwise a malfunction may occur due 0 noise This unit must be properly installed according to directions in the Installation Guide and User Manual Improper installation may cause the unit to malfunc tion or fail This unit must be properly wired according to directions in the Installation Guide and User Manual Improper wiring may cause a malfunction failure or electric shock Do not allow foreign substances including chips wire pieces water or liq uids to enter inside this unit s case Otherwise a malfunction failure elec ric shock or fire may occur When disposing of this unit handle it as industrial waste This section explains the Flex Network 2 Channel Digital Analog Conversion Unit Connection and Circuit Drawings TR SLD 24V Vi T V2 12 TR OV FG Voltage Current Input Input Device Device V14 AG1 FG Ch output current terminals Il AG1 FG Ch 2 output voltage terminals 00 V2 AG2 FG Ch 2 output current terminals 12 AG2 FG Output Circuit Drawing Voltage Output DIA NE Tan i foltage Conversion E I N Tae Amplifer Current Output AG Unit De I Ci Conversion h anent OP J Tnpat Amplifer I FG 7 e The unit s power
5. hts reserved
6. m rover zvoc O B NG z UOT ih FN DA02AH41 Ne 7 goeeegeg c ZOMGICIIGIIelaie Sant ST D lt Front View gt lt Side View gt 50 1 97 Factory Default settings Communication speed 6 Mbps S No station No 0 Output Hold Non Hold g g g m g g g g 50 1 97 6 0 24 lt Bottom View gt A Terminal Switch TERM Changes termination ON OFF Turns ON only the unit connected at the end of the communica tion cable B Dip Switches S No Sets the output hold settings communication speeds and station no first digit C Rotary Switch S No Sets S No station no last digit D Status LED ERR PWR Indicates the unit s current operation status Switch Settings Examples of S No station no settings orem OFF Termination OFF g No PiP Switch Rotary oN ema J swa _ Smtr N6 sw OFFO ONG o RARR 10h 16 uio H12 SWw2 1234 H12 208 Arrow tip Setting values AS 0 to F e When rotating the Rotary Switch be sure to use a standard flat blade screwdriver that is small enough to fit easily into the switch s slot Also using exces sive force to turn the
7. ngs area you will need to update the driver file You can download the latest driver from Pro face s Home Page For GP3000 Series You can select the Flex Network Driver via GP Pro EX as an T O driver Also you can download the driver and the Flex Network 2 Channel Analog Unit User Manual from Pro face s web site http www pro face com 3 2 Channel Analog Unit Wiring a Unit Installtion E Installing on a DIN rail This procedure installs the unit on a 35mm DIN rail Installation Removal Hook the unit s top face groove Use a screwdriver to push the over the top edge of the DIN attachment hook down and re rail Next push the bottom of lease the unit Then pull the unit the unit forward until the at forward and off the rail tachment hook clicks into place on the DIN rail DIN rail o Unit Flathead screwdriver Push down p Be sure that the top and bottom faces of the unit important are facing the correct direction and the unit is installed in a vertical position Incorrect installation may prevent heat from dissipating UL c UL Application Notes The FN DA02AH41 is a UL c UL listed product UL File No E220851 The FN DA02AH41 unit conforms to the following standards m UL508 Electrical Control System for Industry E CAN CSA C22 2 No 1010 1 92 c UL recognition Safety requirements for electrical equipment for measure ment control and laboratory use FN DA02AH41 UL Registration
8. s using this unit should be designed so that output signals which could cause a serious accident are monitored from outside the unit This unitis designed to be a general purpose device for general industries and is neither designed nor produced to be used with equipment or systems in potentially life threatening conditions If you are considering using this unit for special uses including nuclear power control devices electric power devices aerospace equipment medical life support equipment or trans por tation vehicles please contact your local Flex Network distributor A WARNINGS e Whenever installing dismantling wiring and conducting maintenance or in spections be sure to disconnect power to this unit to prevent the possibility of electric shock or fire Do not disassemble or remodel this unit since it may lead to an electric shock or fire Do not use this unit in an environment that contains flammable gases since an explosion may occur Do not use this unit in an environment that is not specified in either the Installation Guide or User Manual Otherwise an electric shock fire mal function or other failure may occur Because of the possibility of an electric shock or malfunction do not touch any power terminals while the unit is operating A CAUTIONS e Communication cables or I O signal lines must be wired separately from the main circuit high voltage large current line high frequency lines such as inverter lin
9. ses this conformance marking Therefore it is strongly advised that the user investigate and confirm whether their overall system i e all related machinery and equipment also conforms with these EMC direc tives 1 The National Electrical Code states that Class 2 power supplies and Class 2 transformers should not exceed an output of 30V and 8A and should not exceed 100VA E Installing in a panel Drill attachment holes for installing the unit using the dimen sions given below Secure the I O unit in place with M4 size screws The torque should be 1 0 to 1 3 Nem Unit mm in 2 4 2 0 17 41 0 1 61 75 0 1 5 2 95 0 06 5 Wiring This section describes both the cables and crimp terminals used for wiring each type of cable The fastening torque for the ter minal screws should be 0 6 to 1 0 Nem lor 2 terminals can be connected to a single terminal screw E Flex Network Communication Cable The Flex Network interface and the Conversion unit or all distributed I O units are connected using a cross wiring system T type systems cannot be used Use the following types of communication cables Distributor Digital Electronics Corporation Order Code FN CABLE2010 31 MS FN CABLE2050 31 MS FN CABLE2200 31 MS a External Dimensions Part Names This section shows the external dimensions of the unit part names and part settings Unit mmf in 85 3 35 Am SE cer op
10. supply should be separated from NS the sensor s power supply to prevent the unit from being affected by external noise e All FG terminals are grounded internally E To Prevent Unit Damage e Avoid storing or operating this unit in either direct sunlight or excessively dusty or dirty environments e Because this unit is a precision instrument do not store or use it in locations where excessive shocks or vibration may occur e Avoid covering this unit s ventilation holes or operating it in an environment that may cause it to overheat e Avoid operating this unit in locations where sudden tempera ture changes can cause condensation to form inside the unit e Do not use paint thinner or organic solvents to clean this unit Package Contents E Flex Network 2 Channel Digital Analog Conversion Unit FN DA02AH41 E Flex Network 2 Channel Digital Analog Conversion Unit Installation Guide this guide GaP coe crm ron eee O gaeeaace O P e e eee e Driver amp Manual The driver for the Flex Network Unit is required in order to use the unit For GLC2000 Series and LT Series You can select the Flex Network Driver via GP PRO PBIII C Package Pro Control Editor or LT Editor If the selection of the appropriate unit s name does not appear in the I O Configuration I O Unit Setti
11. switch can damage the switch Dore D When preparing the cable wire ends Cover shielded wires with shield tape or with an insulation tube Use insulated crimp terminals If you use a crimp type terminal without insulation cover it with a shield tape or an insulation tube Cover uninsulated crimp terminals with shield tape or tube type insulation Blue TR 3 8 0 15 Unit mm in 5 2 0 20 or more Shield wire SLD 63 2 0 13 or larger E Power Cable e Use as large a cable as possible up to 1 25 mm and be sure to twist all wire ends before attaching crimp terminals e Use the same type crimp terminals as used for the commu nication cable E Analog Output Cable e Cable diameter can be up to 0 9mm CPEV S f up to 0 9mm co axial shielded e Use the same type crimp terminals as used for the communication cable e Confirm that all unit terminal screws are securely J _ tightened even if they are not used Important Do not allow pieces of wire to fall inside the unit Note Please be aware that Digital Electronics Corporation shall not be held liable by the user for any damages losses or third party claims arising from the uses of this product Head Office Digital Electronics Corporation 8 2 52 Nanko higashi Suminoe ku Osaka 559 0031 JAPAN Tel 81 0 6 6613 1101 Fax 81 0 6 6613 5888 URL http www pro face com Copyright 2004 Digital Electronics Corporation All rig
Download Pdf Manuals
Related Search