2400VS-DL-VA, 192 Video Segment Instant Access System for
Contents
1. Point press DEL IN OUT 2400VS DL VA Video Segment DoReMi Protocol Video Assist Option e LEARN A SEGMENT INTO A CUE POINT 1 2 3 4 5 6 7 Select VTR 1 2 3 or 4 to establish a Cue Point MARK or ENTER an IN and OUT point on currently selected VTR If Gang mode is desired repeat steps 1 2 until all the VTRs have IN and OUT points Select the desired Cue Point by pressing NEXT CUE LAST CUE or by manually entering the Cue Point using the numeric keypad The selected Cue Point number is shown on the bottom line of the display Press SHIFT MARK to start the LEARN Select VTR If the VTRs are ganged select one VTR that is part of the Gang The rest of the Gang will LEARN automatically Press MARK to complete the LEARN OR Press ESC to exit without LEARNing The ST300 will LEARN save the VTR Number 1 2 3 4 the current gang configuration and the current IN time into the selected Cue Point NOTE If you already have segments defined on the V1 the LEARN command from the ST300 will overwrite them f VIEW THE CONTENTS OF A CUE POINT 1 2 Press SHIFT NEXT CUE OR Press SHIFT LAST CUE The display shows the current cue number and its contents for the current VTR Release the keys to exit the view mode g PLAY A SEGMENT ON THE ST300 1 2 3 Select a video segment by pressing LAST CUE or NEXT CUE OR Enter the desi2. fast wind is initiated and maintained with momentary key press Select fast wind speed 3 9 to 23 7 by pressing Softkey below SPD SLOMO ST300 display shows SLOMO with WHEEL TBAR Speed Prset Press Softkey TBAR or WHEEL to toggle between them NOTE The T BAR has a fixed speed range of 0 gt 200 with a detent at 100 play speed For Wheel only Press Softkey SPEED to select SLOMO speed ranges Press Softkey to select 0 gt 200 OR 100 gt 200 Press Softkey BACK to return to SLOMO MENU Press ESC to exit MENU OR turn the Wheel to select another item Continued on next page 17 2400VS DL VA Video Segment DoReMi Protocol Video Assist Option For Wheel only Press Softkey PRSET to select the SLOMO Preset Speed Mode Press Softkey UPDATE When exiting SLOMO mode the last used speed is saved in the Preset Speed register Press Softkey STATIC The Preset Speed register is NOT updated when exiting SLOMO mode It is only changed by SHIFT SLOMO PRESET SLOMO ST300 SETUP Press Softkey beneath ClearCues to clear all Cue Points to 00 00 00 00 Press Softkey YES when asked Are You Sure Press Softkey beneath SetDefault to set ST300 to default settings Press Softkey YES when asked Are You Sure DISPLAY The version number for the currently installed software is displayed SOFTWARE VERSION DROP FRAME Press Softkey to select DROP FRAM
3. row of the display shows the current Cue Point number and its contents 6 2400VS DL VA Video Segment DoReMi Protocol Video Assist Option 7 DOREMI MENU NOTE Refer to the DoReMi Labs Manual for more information These Options for 2 Channel V1 only Other models may have a different MENU Turn the wheel to move between menu options a Press Softkey CHG to change specific menu option Available menu options 00 Control remote local 01 Time mode A Time absolute time A Time as LTC VITC Time Time Code 02 Sync from Internal Auto Sync In Input 03 Chase on off 04 Mount 05 Input from Composite S VHS 06 Compress 07 Initialize 08 Format 09 Drop Frame Drop No Drop 10 Time Left If you press CHG in option 04 07 08 the second line of the display shows Are you sure Press Softkey YES or NO b Press ESC to exit the Menu Mode 2400VS DL VA Video Segment DoReMi Protocol Video Assist Option 5 DOREMI OPTION MENU NOTE The 1 Channel V1 has only options 0 19 a Turn the wheel to move between menu options b Press or Softkeys to change specific menu option or MENU to enter the submenu if It exists for the specific menu option Available menu options 00 Auto Play Not supported by DNF 01 Disk Copy Press MENU to toggle between options Source is Not Supported by DNF Full Disk Not Supported by DNF Segment Not Supported by DNF Target 1 Not Supported by DNF Target
4. 0VS DL VA Video Segment DoReMi Protocol Video Assist Option Bottom left Top Left Top Center Top Right 10 Audio In Press to toggle between Analog Digital 11 SCSI Speed Press MENU to toggle between Clock press to select 10 20 MHz Width press to select 8 16 bit 12 VI Type Press to toggle between Player Only Rec Player 13 Video Type Press to toggle between NTSC PAL 14 Nb pixels Press to toggle between Full Limited 15 Decimation Press to toggle between On Off 16 Nb Fields Press to toggle between One Two 17 SCSI ID Press to select 00 07 18 Clks frame 19 Emulate Press to toggle between VI BVW 75 20 Audio Ch Press to toggle between 0 2 21 Jog On Not Supported by DNF 22 Loop mode Press to toggle between On Off 23 Edit Time Press MENU to select Edit IN press to select 04 10 Edit Out press to select 04 10 24 Stripe TC Press Softkey CHG to save The display will prompt Are you sure Press Softkey YES to stripe NO to not stripe 25 Odd Fields Press to select Under 00 under 100 26 Stop Chase Press to select Nb frames 00 10 27 Fast mode Press to toggle between Normal Enhanced 28 Jog speed Press to toggle between No Limit Limit to 100 29 Stop Mode Press to toggle between Still Mode EE Mode 30 Version Number Press MENU to see informa
5. 12843 Foothill Bivd Suite D Sylmar CA 91342 818 898 3380 voice L aa 818 898 3360 fax www dnfcontrols com Model 2400VS DL VA amp 2400VS DL VA T 192 Video Segment Instant Access System DoReMi Labs Protocol Video Assist Option USER MANUAL 2400VS DL VA Video Segment DoReMi Protocol Video Assist Option 1 2 Table of Contents REVISION HISTORY DESCRIPTION DEFINITIONS GETTING STARTED SYSTEM INSTALLATION a SHOTBOX b ST300 S SM VTR DDR Controller c LCDDISPLAY DOREMI MENU DOREMI OPTION MENU THE ST300 a MARKTHEIN OUT POINT b VIEW THE IN OUT POINT c ENTERANIN OUT POINT d DELETE IN OUT POINT e LEARN A SEGMENT INTO A CUE POINT f VIEW THE CONTENTS OF A CUE POINT g PLAY A SEGMENT ON THE ST300 h LOOP PLAY A SEGMENT RECALL a RECALL ON THE ST300 b RECALL ON THE SHOTBOX THE SHOTBOX a LEARN ON THE SHOTBOX b VIEW CONTENTS OF CUE POINTS SHOTBOX BANK and SWITCH INDICATORS SHOTBOX CONTROL SWITCHES SHOTBOX SWITCH MAPPING TO CUE POINT LOCATIONS TRANSFERRING CUELIST TRANSMIT CUE LIST FUNCTION b RECEIVE CUE LIST FUNCTION c d e a REFERENCE 10 11 12 13 14 SETUP MENU FUNCTION TABLE SPECIFICATIONS ST300 ST320 SHOTBOX KEY LAYOUTS DNF CONTROLS LIMITED WARRANTY Manual Version ccccceeeeeeeeeeeeeeeeeeneeeeeeeeeeees 2 3 012904 Document NO nsise 2400VS DL VA_User_Manual doc 2400VS DL VA Video Segment DoReMi Protocol Video Ass
6. E ON or OFF Used in conjunction with Timecode Generator preset RECORD Press Softkey to select single button or 2 button record RECORD REC Only OR REC PLAY FRAMES PER Select number of frames per second for Video Assist Normal play 24 or 30 fps Default is 24 TRANSMIT CUE Allows the user to transfer the cuelist to another ST300 or to a PC POINT LIST RECEIVE CUE Allows the user to receive the cuelist from another ST300 or a PC POINT LIST 18 2400VS DL VA Video Segment DoReMi Protocol Video Assist Option 11 FUNCTION TABLE Function Key Press Description EE On Off EE Toggle EE mode on off Status indicator is on when EE is on ENTER TIME ENTER TIME To manually entered timecode numbers into the currently displayed Cue Point Enter the desired timecode number using the numeric keypad Press ENTER to save your entry OR ESC to exit without saving To enter a GOTO location without altering the contents of the Cue Point enter the desired timecode number using the numeric keypad Press GOTO to search to the entered time Press ESC to exit without searching GOTO IN RECUE Search the VTR to the current IN Point GOTO GOTO To enter a GOTO location without altering the contents of the ENTERED Cue Point Press ENTER TIME Enter the desired TIME timecode number using the numeric keypad Press GOTO to search to the entered time Press ESC to exit without searching GANG SHIFT VTR 1 Select V
7. Power 90 VAC to 265 VAC adapter supplied with IEC connector Size L x W x H 10 5 x 7 25 x 1 75 front 3 0 rear Weight 4 lbs Rear Panel Connectors Power DB9M OUTPUT DB9F Display Easy to read 2 line backlit LCD display User adjustable contrast RS422 SERIAL CONNECTOR 9 Pin D Type Female DB9F Pin 1 Frame Ground 6 Transmit Common 2 Transmit A gt 7 Transmit B gt 3 Receive B 8 Receive A 4 Receive Common 9 Frame Ground 5 Spare POWER CONNECTOR 9 Pin D Type Male DB9M Pin 1 5v DC 6 No Connection 2 5v DC 7 Ground 3 Ground 8 Ground 4 No Connection 9 Ground 5 No Connection 22 2400VS DL VA Video Segment DoReMi Protocol Video Assist Option 13 KEY LAYOUTS SI 300 KEY CONFIGURATION 2400V5 D O O O O 2ueosPur LINE DISPLAY K BAVK SHECT S720 E SHOIBOX E 5 S JS S ES ny 23 2400VS DL VA Video Segment DoReMi Protocol Video Assist Option 14 DNF CONTROLS LIMITED WARRANTY DNF Controls warrants its product to be free from defects in material and workmanship for a period of one 1 year from the date of sale to the original purchaser from DNF Controls In order to enforce the rights under this warranty the customer must first contact DNF s Customer Support Department to afford the opportunity of identifying and fixing the problem without sending the unit in for repair If DNF s Cu
8. TRs to gang together The ganged VTR s LEDs will SHIFT VTR 2 turn on Press ESC to exit SHIFT VTR 3 SHIFT VTR 4 FFWD FFWD Press and HOLD to shuttle Release key to stop Set WIND Speed in MENU JOG Select JOG mode and enable the Wheel LAST CUE LAST CUE Step to the previous Cue Point Location NEXT CUE NEXT CUE Step to the next Cue Point Location RECORD REC Places VTR in the Record mode selected by RECORD MODE in the SETUP MENU One button record REWIND RWD Press and HOLD to shuttle Release key to stop Set WIND Speed in MENU SHUTTLE SHUTTLE Select SHUTTLE mode and enable the Wheel STOP STOP Press once to STILL frame VTR Press again to put VTR into STOP mode TIME MODE TIME MODE Press to toggle between Timecode TC VITC VT or Tape SELECT Timer TM display modes 19 2400VS DL VA Video Segment DoReMi Protocol Video Assist Option LOOP PLAY LOOP PLAY Video segment plays from first frame of video to last frame then plays again from first frame Function is continuous PLAY SHIFT Plays Video Segment from In Point to OUT Point SEGMENT TIME PRESET SHIFT Press to enter Time Preset Press ENTER to load Time Generator Preset TIME MODE Generator OR press ESC to exit without saving Video Assist SPEED SELECT Turn the wheel to select desired speed 0001 2500 frames per Speed Select second Video Assist SHIFT FFWD Plays the video forward at the pre se
9. ack to the IN Point Pressing LOOP puts the VTR into Loop Segment Mode The CONTROL Switch indicators show the real time status of the VTR 13 2400VS DL VA Video Segment DoReMi Protocol Video Assist Option e SHOTBOX SWITCH MAPPING TO CUE POINT LOCATIONS The SWITCHES on the SHOTBOX access the ST300 s Cue Point locations as follows BANK 1 SWITCHES 1 gt 48 access Cue Point locations 101 gt 148 BANK 2 SWITCHES 1 gt 48 access Cue Point locations 201 gt 248 BANK 3 SWITCHES 1 gt 48 access Cue Point locations 301 gt 348 BANK 4 SWITCHES 1 gt 48 access Cue Point locations 401 gt 448 14 2400VS DL VA Video Segment DoReMi Protocol Video Assist Option 15 TRANSFERRING CUELIST The TRANSMIT CUELIST function allows you to transmit your list of Cue Points to a PC using the provided utility software on the PC or to another ST300 Transfer to a PC requires OpSuite 3 0 software which runs on a Windows based computer Contact DNF Controls for more information a TRANSMIT CUE LIST FUNCTION 1 To Transmit Cue Points to the ST300 a Connect the VTR4 connector on the rear of the ST300 to the VTR4 connector of the receiving ST300 using an RS422 9 pin cable with TX and RX lines crossed A turnaround cable b Press MENU and scroll the Wheel to Transmit CUE List YES Enter Exit ESC c Press ENTER to start transmitting The Display shows Waiting to transmit on the first line d When th
10. e Receiver is ready transfer starts automatically The Display now shows Transmitting cuelist e After the transfer is over the display shows Transfer is over for one second and then shows Waiting to transmit again f Connect another ST300 to transmit the list again OR Press ESC twice to exit the MENU mode 2 To Transmit Cue Points to the PC a Connect the VTR4 connector on the back of the ST300 to one of the COM ports on the PC using a RS422 to RS232 adapter b Repeat steps b f of the TRANSMIT CUE POINTS to the ST300 section 2400VS DL VA Video Segment DoReMi Protocol Video Assist Option 16 b RECEIVE CUE LIST FUNCTION The RECEIVE CUELIST function allows you to receive your list of Cue Points from a PC or from another ST300 Transfer to a PC requires OpSuite 3 0 software which runs on a Windows based computer Contact DNF Controls for more information 1 To Receive Cue Points from the ST300 a Connect the VTR4 connector on the back of the ST300 from the VTR4 connector of the transmitting ST300 using RS422 9 pin cable with TX and RX lines crossed A Turnaround Cable b Press MENU and scroll the Wheel to Receive CUE List YES Enter Exit ESC c Press ENTER from start receiving The Display shows Waiting to receive on the first line d When the Transmitter is ready transfer starts automatically The Display now shows Receiving cuelist e After the transfer is
11. e of the display shows the IN point of the Segment that was selected by the SHOTBOX or ST300 The bottom line also shows the currently selected VTR on the ST300 This is the VTR that is currently being controlled 1 Press and hold VIEW 2 Select the desired BANK 1 2 3 or 4 The indicator on the selected bank will turn on 3 Press the desired SWITCH The contents of the Cue Point IN and OUT Points assigned to this BANK and SWITCH will be shown on the display The indicator on the pressed SWITCH will turn on For example 1 IN 00 00 01 00 OUT 00 00 02 00 On VTR 1 IN is 00 00 01 00 On VTR 1 OUT is 00 00 02 00 If no time is assigned to the switch the NO ASSIGNMENT message will be displayed 4 Press the same switch 4 times to see all 4 VTRs Cue Point assignments 5 Release VIEW at anytime when done c SHOTBOX BANK and SWITCH INDICATORS The BANK key indicators show the currently selected bank The SWITCH key indicator shows the last selected or viewed Cue Point Only one BANK and SWITCH indicator are on at a time Sometimes one BANK indicator will be on and all the SWITCH indicators will be off The BANK and SWITCH indicators that are currently on show the location of the selected Cue Point OR the location of the last viewed Cue Point d SHOTBOX CONTROL SWITCHES Pressing PLAY puts the VTR into PLAY Segment mode Pressing STOP puts the VTR into STOP mode Pressing RECUE stops the VTR and cues b
12. ing Started 3 SYSTEM INSTALLATION a SHOTBOX 1 Plug one end of a standard 9 pin RS422 serial cable into the OUTPUT connector 9 pin female on the rear of the SHOTBOX Plug the other end of the cable into the AUX connector on the rear of the ST300 2 Connect the 5 VDC 1Amp POWER SUPPLY into the POWER connector on the rear of the SHOTBOX Plug the Power Supply into an outlet 90 VAC 240 VAC b ST300 S SM VTR DDR Controller 1 Plug one end of a 9 conductor RS422 serial cable into the 9 pin connector VTR 1 VTR 2 VTR 3 or VTR 4 on the rear of the ST300 Plug the other end of the cable into the 9 pin REMOTE connector on the Video Server 2 Connect the 5 12 12 VDC POWER SUPPLY into the POWER connector on the rear of the ST300 Plug the Power Supply into an outlet 90 VAC 240 VAC 3 Select REMOTE mode on the VTR s front panel 4 Check the SETUP MENU prior to using ST300 to confirm proper Record mode SLO MO speed range and other User settable modes Installation is complete CONNECTION DIAGRAM 5T300 5 5M fey i POWER SUPPLY 5 2400VS DL VA Video Segment DoReMi Protocol Video Assist Option c LCD DISPLAY During normal operation the top row of the display shows the selected time mode and current time location of the VTR For example TM 01 12 09 23 Time Modes TM Tape Timer TC LTC VT VITC The currently selected SLO MO speed is displayed on the far right side of the top row The bottom
13. ist Option PN 1 REVISION HISTORY 100703 Rev 2 2 Company header information revised 012904 Rev 2 3 Reformatted Updated Transmit Cue List and Receive Cue List function description Added DNF Controls Limited Warranty 3 2400VS DL VA Video Segment DoReMi Protocol Video Assist Option 4 DESCRIPTION NOW Load and Play video segments on the DoReMi DDR The 2400VS DL VA System consists of an ST300 with Video Segment software and the Video Assist software option and an ST320 SHOTBOX TBAR or detented Wheel for Fast and Easy slomo ing 0 200 or 100 to 200 of Play speed The Video Segment option for the ST300 in combination with a Video Server provides a Quick and Easy way to access and play up to 192 video segments Each ST300 Cue Point consists of an IN point and an OUT point IN OUT points can be manually entered OR marked with the current tape time from the Video Server All Cue Points are retained when power is off DEFINITIONS Q Throughout this document VTR DDR VDR amp Video Server will be referred to collectively as Video Server Q The ST300 S SM as the ST300 a The ST320 SHOTBOX is referred to as SHOTBOX SHOTKEY refers to the 1 50 switches on the SHOTBOX Q Words surrounded by brackets for example ENTER are keys on the ST300 or the SHOTBOX XXX XXX means hold the two keys down simultaneously 2400VS DL VA Video Segment DoReMi Protocol Video Assist Option Gett
14. lected speed Turn the FFWD wheel to change the speed Press any transport key to exit Video Assist SHIFT REWIND Plays the video backward at the pre selected speed Turn the Rewind wheel to change the speed Press any transport key to exit 20 2400VS DL VA Video Segment DoReMi Protocol Video Assist Option 12 SPECIFICATIONS ST300 Power Size Weight Rear Panel Connectors Display Jog Shuttle Wheel Optional T bar 90 VAC to 265 VAC adapter supplied with IEC connector L x W x H 12 x 6 x 1 5 front 3 0 rear 4 lbs VTRI VTR2 VTR3 VTR4 All DB9F GPI DBF15F Power DB9M Aux DB9F Fasy to read 2 line back lit LCD display User adjustable contrast With mechanical detents Slo mo 0 200 of Play Speed RS422 SERIAL CONNECTOR 9 Pin D Type Female DB9F Pin 1 Frame Ground 6 Receive Common 2 Receive A 7 Receive B 3 Transmit B gt 8 Transmit A gt 4 Transmit Common 9 Frame Ground 5 Spare POWER CONNECTOR 9 Pin D Type Male DB9M Pin 1 5v DC 6 5 VDC 2 5v DC 7 Ground 3 Ground 8 Ground 4 12 VDC 9 Ground 5 12 VDC GPI IN OUT CONNECTOR 15 Pin D Type Female DB15F Pin 1 GPI 1 Out 9 GPI 1 In 2 GPI 2 Out 10 GPI 2 In 3 GPI 3 Out 11 GPI 3 In 4 GPI 4 Out 12 GPI 4 In 5 GPI 5 Out 13 GPI 5 In 6 GPI 6 Out 14 GPI 6 In F GPI 7 Out 15 GPI 7 In 8 Ground 21 2400VS DL VA Video Segment DoReMi Protocol Video Assist Option ST320 SHOTBOX
15. over the display shows Done Success Press any key f Press any key The display shows Receive cuelist message g Press ESC to exit the MENU mode 2 To Receive Cue Points from the PC a Connect the VTR4 connector on the back of the ST300 to one of the COM ports on the PC using RS422 to RS232 adapter b Repeat steps b g of the RECEIVE CUE POINTS from the ST300 section 2400VS DL VA Video Segment DoReMi Protocol Video Assist Option Reference 10 SETUP MENU Press MENU The MENU indicator will turn on The display will show ST300 Setup Menu The second line on the display shows YES gt Press or gt to select DOREMI Menu or DOREMI Options Menu Press Softkey YES to select the SETUP MENU For the ST300 MENU Turn the Wheel to select item to change Press MENU OR use the Softkeys to change the desired mode for that option Turn the Wheel at anytime to select another item Press ESC at anytime to exit SETUP MENU The MENU indicator will turn off MENU MODES Turning Wheel Clockwise RECORD Press MENU to select the desired record mode Lockout Assemble Crash Full or Insert Only in INSERT mode Press the associated Softkey located below the display to toggle Video V Audiol A1 Audio2 A2 Audio3 A3 Audio4 A4 on off WIND MODE Press Softkey to select HOLD fast wind is maintained only while key is depressed OR LATCH
16. red cue number on the numeric keypad Press GOTO Press and hold SHIFT then press and release PLAY h LOOP PLAY A SEGMENT Press LOOP PLAY to continuously loop playback the segment 11 2400VS DL VA Video Segment DoReMi Protocol Video Assist Option 12 RECALL a RECALL ON THE ST300 1 Select the desired Cue Point by pressing NEXT CUE or LAST CUE or by manually entering the Cue Point using the numeric keypad The selected Cue Point number is shown on the bottom line of the display 2 Press GOTO on the ST300 The In and Out of the Cue Point becomes the current IN and OUT points The ST300 parks the learned VTRs at the In point b RECALL ON THE SHOTBOX Select the desired Cue Point by pressing the bank and the switch key THE SHOTBOX a LEARN ON THE SHOTBOX NOTE All the Cue Points are stored in the V1 1 Press LEARN The LEARN indicator will turn on The display will show the prompt Select Bank amp Switch STOP Abort 2 Select the desired BANK and ShotKey 3 Press STOP to exit at any time The SHOTBOX will LEARN save the current time and gang configuration of the active VTR s 2400VS DL VA Video Segment DoReMi Protocol Video Assist Option b VIEW CONTENTS OF CUE POINTS The top line of the display shows the BANK and SWITCH location for the selected Cue Point If a Cue Point was selected from the ST300 and not the SHOTBOX the BANK and SWITCH will be set to 0 The bottom lin
17. rices listed in the DNF Controls Price List DNF Controls reserves the right to refuse repair of any unit outside the warranty period that is deemed non repairable DNF Controls shall not be liable for direct indirect incidental consequential or other types of damage resulting from the use of the product HHH 24 2400VS DL VA Video Segment DoReMi Protocol Video Assist Option
18. s Not Supported by DNF 02 Edit Preset Press MENU to toggle between options Al press to toggle On Off Insert press to toggle On Off Assemble press to toggle On Off Video press to toggle On Off TC press to toggle On Off A2 press to toggle On Off 03 Set Video Press MENU to toggle between options Delay press to set 00 310 sec ChromHue press to set 128 127 ChromSat press to set 128 127 Lumacont press to set 128 127 LumaBrit press to set 128 127 PAL switch 0 Black press to toggle between 0 0 7 5 IRE HTRIG press to select desired value HTRIG press to toggle On Off CH PH press to select desired value Pattern press to toggle On Off 04 Save Press Softkey CHG to save The display will prompt Are you sure Press Softkey YES to save VO to not save 05 Disc Access Press to toggle between Play amp Record Play Only 06 Frame Mode Press to toggle between On Off Play Only 07 Step Rec Press to toggle between Disabled Enabled 08 Clip menu Press to scroll the list of available clips 09 TC burn in Press MENU to toggle between Color press to selelct Off White Black White Bkgd Black White Black Bkgd Position press to select Bottom Right Bottom_Center 8 240
19. stomer Support Department cannot fix the problem the customer will be issued a Returned Merchandise Authorization number RMA The customer will then ship the defective product prepaid to DNF Controls with the RMA number clearly indicated on the customer s shipping document The merchandise is to be shipped to DNF Controls 12843 Foothill Blvd Suite D Sylmar CA 91342 USA Failure to obtain a proper RMA number prior to returning the product may result in the return not being accepted or in a charge for the required repair DNF Controls at its option will repair or replace the defective unit DNF Controls will return the unit prepaid to the customer The method of shipment is at the discretion of DNF Controls principally UPS Ground for shipments within the United States of America Shipments to international customers will be sent via air Should a customer require the product to be returned in a more expeditious manner the return shipment will be billed to their freight account This warranty will be considered null and void if accident misuse abuse improper line voltage fire water lightning or other acts of God damaged the product All repair parts are to be supplied by DNF Controls either directly or through its authorized dealer network Similarly any repair work not performed by either DNF Controls or its authorized dealer may void the warranty After the warranty period has expired DNF Controls offers repair services at p
20. tion about version number serial number RAM size etc c Press ESC to exit the Menu Mode 9 2400VS DL VA Video Segment DoReMi Protocol Video Assist Option 10 THE ST300 NOTE All the Cue Points are stored on the V1 The current segment number and its contents are shown on the bottom line of the display Press NEXT CUE or LAST CUE to step through the list of segments one at a time a MARK THE IN OUT POINT 1 The IN OUT indicator is OFF 2 Press IN OUT The IN OUT indicator turns ON the second row of the display shows the currently marked IN OUT time for second The current time is marked into the IN OUT point VIEW THE IN OUT POINT 1 When the IN OUT indicator is ON the content of an IN OUT point can be viewed by pressing and holding IN OUT 2 Press GOTO or RECUE to search to the current IN OUT point ENTER AN IN OUT POINT 1 Press SHIFT IN OUT The first row of the display shows the current IN OUT time The second row of the display shows ENTER IN OUT If there is no IN OUT point currently selected on that VTR the first row of the display shows 27 27 7 2 Enter the desired IN OUT time using the numeric keypad 3 Press ENTER to save entered time as an IN OUT time OR Press GOTO or RECUE to save entered time as an IN OUT time amp search to it OR Press ESC to exit without saving DELETE IN OUT POINT To Delete an IN OUT
Download Pdf Manuals
Related Search