ECO Spot™ LED B40E User Manual
Contents
1. max image size and brightness use D Size gobos The recommended gobo image diameter is 32mm An Image Diameter of up to 40mm is possible with some loss in focusing quality for optimal focus stay within 28mm image size Unscrew the thumbscrews to remove the front cover with the projection lens Push the two pins of the gobo retaining ring together and pull out the retaining ring Carefully remove the old gobo and replace it with the new gobo Tip Tilt the projector forward while placing the palm of your hand inside the old gobo will fall into your hand If you have a glass gobo place the more reflective side towards the light bulb Replace the retaining ring and make sure it evenly pushes the gobo all the way back Replace the front cover and adjust the focus by threading the projection lens in or out Copyright 2015Globus New Media LLC Page 3 ECO Spot LED B40E User Manual Line Voltage 100 240V 50 60Hz 0 6A 48W Ambient Operating Temperature 13 to 104 F 25 to 40 C Dimensions Weight Body without yoke 10 5 x 6 x 3 75in Lx W x H 267 x 153 x 95mm The projection lens adds 0 5 to 2in 12 to 50mm to the length Height with yoke 7 75in 197mm Weight 7lbs 3kg Gobo Dimensions D Size Metal or Glass Gobos and Dichroic filters The projector takes D Size gobos Outer Diameter OD 53mm Image Diameter ID 32mm Max Thickness 4mm Larger ID up to 40mm is possible with some loss2. ECO Spot LED B40E User Manual ECO Spot LED B40E User Manual The ECO Spot LED40DE is intended for exterior applications but is also suitable for interior use Thank you for choosing an ECO Spot Gobo projector This unit is equipped with a fan cooled heat pipe to keep the 40W High Power LED running cool It is also available as interior version ES B40 Please read this manual before installing or operating this fixture follow the safety precautions listed below and observe all warnings WARNING To prevent damage to the LED always connect the driver cable to the projector FIRST before plugging it into the power outlet Package Contents v Projector External LED Driver Test Gobo Spare gobo retaining ring and spare drive belt Gobo adapter ring for E Size Gobos Safety Information Place your fixture at a suitable place with good air flow Keep flammable materials away from the fixture Minimum distance to flammable material 1 ft 0 3m Provide a minimum clearance of 4 in 10cm around air vents Use only genuine spare parts for part replacement Do not look directly into the lamp it can result in eye damage Always unplug the unit from the power mains before any service is done Light fixtures should be installed and maintained only by qualified personnel with experience in lighting equipment and general electrical experience Electrical Safety Disconnect the fixture from AC power before handling
3. in focusing quality for optimal focus stay within 28mm image size An adapter for the smaller E Size gobos is available ECO spot pho Maciel _PRotometrics _ _ B Color Baam Eftective co Gobo ire Temp Mult bent 5 7 140mm Image Dimm FC Hroar pita HEJJA F5 LED Ba0E B000n ihararvaticr Fe j SOG image Diam 0 oe Tarr 00 s0000 Merce ree o gt oo a 2 i Iharanation He Page 4 LLC Extremely high light density for ultra efficient projection Power 40W 6 Bulb life 50 000h Color Temperature 6 000k 500k Rated Luminous flux 3 000lm Effective luminous flux 2 400Im The projector can be equipped with standard ECO Spot projection lenses A larger focal length f makes a smaller projection angle and therefore a smaller but brighter image Currently these lenses are available e Wide f 50mm 35 25 for D E Size gobos Medium f 70mm 28 20 for D E Size gobos Semi Narrow f 100mm 21 15 for D E Size gobos Narrow f 140mm 14 10 for D Size gobos IP Ratings LED Driver IP65 Fixture equivalent to IP62 Copyright 2015 Globus New Media Page 4
4. ng brightness at varying distances The more narrow the lens the smaller and brighter the image will be at a given distance For example cutting the projection size in half will quadruple its brightness Gobo Rotator If the fixture is equipped with a gobo rotator it can be turned on off with the silver push button on the front plate underneath the lens There are no controls for rotating speed or direction Power up the projector If the fixture is equipped with a gobo rotator turn it on once the gobo projects in the desired position turn it off Loosen the outer ring around the lens that acts as a water seal Focus the projection by twisting the lens in and out until the image is well focused When used for the first time the lens will often need to be twisted outwards many rotations to reach the focusing point When in doubt keep going Re tighten the outer ring to ensure a tight seal of the lens Page 2 Copyright 2015 Globus New Media LLC Page 2 ECO Spot LED B40E User Manual Multi functional Yoke The yoke can slide over the whole length of the fixture body to accommodate a wide range of pointing directions The yoke can also serve as stand The yoke can be screwed to a wall or ceiling or fastened with a C clamp Gobo Placement see Specifications for Gobo Dimensions The ES LED40DE uses D Size gobos or E Size gobos with an adapter ring See the Specifications for exact dimensions For
5. the fixture Always ground earth the fixture electrically Use only a power source that complies with local building and electrical codes and has both overload and ground fault protection Do not use the fixture if the power cable or power plug is in any way damaged defective or wet or if they show signs of overheating Copyright 2015Globus New Media LLC Page 1 ECO Spot LED B40E User Manual Handling Instructions There is a weatherproof connector between the driver power supply and projector which can be opened for easier handling Always make this connection first before powering up the driver otherwise the LED can be damaged by the power surge Before the initial start up please unpack and carefully check for damage caused during transportation Place your fixture at a suitable place with good air flow Make sure there are no flammable materials close to the lamp When suspending the fixture above ground level verify that the structure can hold at least 10 times the weight of all installed devices Verify that all external covers and rigging hardware are securely fastened and use an approved means of secondary attachment such as a safety cable Warranty One Year from Date of Purchase Keep your receipt for reference and contact your dealer in case of warranty issues Projection Lenses The projector accommodates interchangeable projection lenses to allow optimizing the projection size and resulti
Download Pdf Manuals
Related Search