User manual V01_Rev04_EN
Contents
1. 1 Use the included screws to fasten the holder to the ceiling at a suitable location typically in the centre of the room Subsequently insert the smoke sensor in the holder wd Route the cable to the controller and connect it to a free port 4 Youcan now check the sensor function by blowing some smoke into the sensor or by pressing the test button located on the side of the smoke detector Information The smoke detector cannot be used under adverse conditions e g extremely cold or hot or hazy ambient conditions The smoke detector should be checked once per month Please clean the sensor once per six months with a soft brush or similar cleaning implements Subsequently verify the functioning of the sensor 6 2 Switchable multi socket outlet The switchable multi socket outlet is not a sensor capable to trigger an alarm However there is the possibility to switch any load on and off which can be connected to a standard socket outlet The switchable multi socket outlet provides two connecting cables There is one standard 230 V cable which can be plugged into a wall outlet The second cable is fitted with a controller sensor plug for connection to a controller port Up to ten switchable multi socket outlets can be connected and operated at the same time Please read the instructions in section 5 5 switchable multi socket outlets for information how to switch the multi socket outlet on or off by sending SMS commands Impo2. Temperature RH monitoring Magnetic contacts for windows doors etc Power failure GSE over temperature timer box External alarm system Automatic sensor detection at each of the ten ports Data transmission security adjustable from normal to encoded SMS control of up to ten 230 V multi socket outlets Minimum and maximum temperature and air humidity adjustable via SMS Storage for up to two phone numbers Retrievable controller status Language selection German English Adjustable delay time 0 180 seconds before alarm is armed Use of external key switch is possible 2 Technical data Power adapter 100 240 V 50 60 Hz Supply voltage 12 VDC 10 Supply current Min 500 mA Temperature range 10 C to 50 C Humidity range 0 to 95 GSM frequencies 900 1800 1900 MHz Dimensions L x W x H 80 x 140 x 78 mm 3 Initial operation Before operating the system for the first time the following check points must be observed in order to guarantee a trouble free function SIM card configuration o Insert the SIM card that you want to use in any mobile phone and set the PIN code to 0000 o Please delete all SMS messages or else they will be deleted by the SMS controller After completing the SIM card configuration you can unscrew the lid of the controller and remove the lid Insert the configured SIM card in the SIM card holder Its chamfered edge must face the edge of the
3. You may personalise the controller as needed to match your application by means of SMS configuration commands These commands are described in detail in section 5 SMS commands 4 SMS alarm controller 4 1 Port1 port10 The SMS alarm controller provides ten independent input output ports Any sensor can be connected to any port The controller detects and installs the sensors automatically when they are connected to a port 4 2 LEDs The controller provides ten port LEDs one power LED and one error LED in order to indicate the operating mode errors and sensor data Power status LED This LED indicates the controller status o Ifthe LED lights continuously the controller is ready for operation o A slowly blinking LED indicates that the controller is starting up upon connection to the mains supply After pressing the programming key the same blinking pattern indicates that the controller waits for an incoming call to store the number Error LED The error LED indicates an error condition The various errors are explained in section 7 error messages Port 1 to port 10 LEDs Each port has its own LED It indicates the port status If the LED is not lit no sensor is connected to the respective port If the LED lights continuously a sensor is connected and has been detected by the controller A fast blinking LED indicates that the controller is armed and the sensor connected to this port has triggered an alarm The LED st
4. at a suitable location and connect it to any controller port Technical data Operating range temperature 0 to 50 C Temperature tolerance 1 5 C Operating range humidity 10 to 90 not condensing Humidity tolerance 6 Limits Temperature 20 to 70 C Humidity below 95 relative humidity not condensing 17 7 Error messages The table below lists all error messages which the controller is able to display When an error occurs the error LED starts blinking for four seconds before it continues blinking in one second intervals in accordance with the error number Error LED off Error LED is lit Each dot stands for one second on or off In order to obtain the error number one has to count how many times during one cycle the error LED is oft Error no Error LED blinking pattern Description 2 0000000000000000 There is no phone number available Please refer to section Storing a phone number 3 0000000000000000 0000 No SIM card available Check whether SIM card has been correctly inserted 4 0000000000000000 00000000 Pin code has not been set to 0000 Please set pin code to 0000 5 000000000000000 KEES yor Jer st wt No network found Relocate the controller to a place with better reception 6 KESL RL SL St SREL SL St stet ett Startup failure Restart the controller 7 Xx xox Jor Jer Jeox Jor Xer yer XX XX X yor Jer yor yer y
5. is triggered until the controller is disarmed key switch to OFF position Both times are equal and can be configured as described below Due to this delay time it is possible to leave the controlled area after arming the system and to enter the room without causing an immediate alarm The disarming delay is restricted to the motion sensor and magnetic contacts An SMS message will be sent immediately in the case of all other alarms This function can be deactivated by setting a time of 0 seconds Syntax to set the delay time Delay time time in seconds o Example Time delay 30 Time delay 30 Time delay 30 Range 0 to 180 seconds Factory setting 15 seconds 5 6 Additional security configuration This function allows to set the security index Syntax to set the additional security index Security security index Example Security 2 Security 2 Security 2 Range 0 to 3 Factory setting 0 12 6 Sensors This section gives a brief overview of all sensors and their use The controller is only compatible with G Systems sensors Only these sensors must be used The function is no longer guaranteed if sensors are modified or if other sensors are used 6 1 Smoke sensor The smoke sensor is a photoelectric smoke detector The sensor sends a silent alarm to the controller It does not provide a siren Technical data Functional area 20 m Temperature range 0 C to 50 C Humidity range 0 to 95 Installation
6. S 1 1 Status enquiry This SMS command allows to retrieve the controller status at any time and recall the most important pieces of information Syntax for retrieving the current status State Simply send the word State to the controller If the message is correctly received you will get a reply with following data Alarm status On or off o This value shows whether the controller is armed on or disarmed off Reception 0 100 o This value indicates the reception quality at the device Battery voltage Value in volts o Indicates the current battery voltage Sent alarms 0 20 o Indicates the number of alarms sent since the system was last armed If a temperature and humidity sensor is used the following additional values are indicated Temperature Temperature in degrees Celsius o Indicates the current room temperature Humidity Relative humidity in percent o Indicates the current humidity in the room air 5 1 Change system language The system language can be changed by sending an SMS command The controller can be operated in German and English language SMS syntax Deutsch To change the system language to German English To change the system language to English If no error occurred the controller will send back an acknowledgement after a short while Factory setting English 5 2 Storing an additional phone number A secondary phone number can be stored in addition to the
7. SMS alarm controller User manual Version 01 Rev 03 Date 05 10 2010 Released for Official Created by CD Electronics GmbH Table of contents RE ee 2 E KT lee EE 3 1 1 PUNICEIONS sccers assotes vysncee tenses ve ssecB cats ssocd E cavsaed ed ysnce ov stood en T ot stood esasbotenvaencecena s 3 2 TOChnical data issenensis a a a EN EG a NEEAEE e EEEE ENEE 3 3 ERT le d EE A DC OESCH ue ge EE 5 4 1 ele T port JO WEE 5 4 2 LEDS iss cavesadecvasusccevscedtcaisetvaadvsntnedatuentsd caves deddde sanecs dagcdestabaieesstustecoaseasceesvebadedvoatidcevenehicesasagtedenes 5 4 3 Intenmal key SWITCI 2ssccccesceissc desiecesbudesedtetensweceesedesdedel ee owtebeve Ee EENS 5 4 4 BACKUP Battery erreien roge eeaeee aeee eiea sce tes zesnaceautansug seavantaeseeseeeenavegemeesoeesecees 5 4 5 HOUSING PrOteCtlO EE 6 4 6 Reset to factory SEtUIN GS veciiscicccceededeceeewesscdaedcescee vanccedesudicns cadncueetauuieddesalaceacdeenensevarccddeceueeeetdane 6 4 7 Storing PHONE numbers edireitera eitinn ie enie aa eaae aaa Eaha EEE esa A E Nan E aO Ea Eiaa 6 4 8 Additional Ee TEE H 4 8 1 NUME RiCal COdES niiina a E ns Goescend Gidtgeneveecces IS 8 4 8 2 E 8 5 SIMS COMMAS ect si sep cece s sess cde cc trade cuca Phen hee hai tee oy dnt decd daaa aaa aa apaa aaa ae eea dride aei 9 1 1 en EN UE 9 5 1 Change System language ccccccsessssccccecessesesneaecececesesnaeseceesessscseeaeseceseacusseaaeaeeeesenseeseasess 10 5 2 Storing an additional phone
8. additional number please refer to section 5 2 storing an additional phone number 4 8 Additional security This setting allows to increase the security level of the communication between the user and the controller It offers two options On the one hand one can select that the controller connects to the mobile phone network only when a messages needs to be sent Subsequently the connection is ended As a result the controller remains connected to the network for not more than 45 seconds and in most instances the device cannot be located The second option allows to send numerical codes in place of alarm texts via SMS This has the advantage that only the user knows what has been sent and which alarm was triggered The security status can assume the following values Security status 0 This is the standard security status The additional security features are deactivated Alarms are sent as texts and the controller is permanently connected to the mobile phone network This is the factory setting Security status 1 If the security status is set to 1 the controller connects to the mobile phone network only if required to send an alarm message The alarms are sent as texts Since a connection needs to be established at first the despatch of alarm messages is delayed by approximately 30 seconds Security status 2 If the security status is set to 2 alarms are no longer sent as texts but as numerical codes The controller is permanently c
9. and connecting cable and the bottom side with the sensitive sensor surface A single drop of water on the sensor surface is sufficient to trigger an alarm Important After an alarm the sensor should be dried thoroughly to prevent subsequent false alarms 6 5 External key switch If an external key switch is used the internal key switch will be disabled Up to one external key switch can be connected If an external key switch is connected the internal key switch must be in ON position to ensure the correct functioning of the system To find out whether an external key switch is in ON or OFF position the LED status at the corresponding port can be checked If the LED blinks slowly the switch is in OFF position If the LED lights continuously the switch is in ON position Installation in power off condition o Disconnect mains supply and wait for all LEDs to go off o Set external key switch to OFF position Plug in the switch o Set internal key switch to ON position and remove the key o Restore main power supply and start up the controller External key switch can now be used The internal key switch is now disabled Installation in active condition o Set the internal and external key switches to OFF o Plug in external key switch o Set internal key switch to ON position and remove the key External key switch can now be used The internal key switch is now disabled The external key switch can be removed as follows Removal in pow
10. er off condition o Disconnect mains supply and wait for all LEDs to go off o Set internal and external key switches to OFF position o Disconnect external key switch Restore main power supply and start up the controller The controller can now be operated with the internal key switch Removal in active condition o Set external key switch to OFF position o Set internal key switch to OFF position o Disconnect external key switch The controller can now be operated with the internal key switch 16 6 6 Magnetic contact The sensor is a two piece magnetic switch This sensor is especially suited for monitoring windows doors gates hatches etc Mode of operation The magnetic switch must be installed in a manner which ensures that the two parts separate when for instance the door opens No alarm is triggered when the two parts touch one another or when they are separated by a very small gap An alarm will be triggered however as soon as the two parts separate Ensure that the sensor is well fastened to avoid unnecessary false alarms 6 7 Temperature and humidity sensor The temperature and humidity sensor is a digital sensor which measures the current temperature and humidity If the temperature or humidity exceeds or falls below the preset alarm values an alarm will be triggered These alarm values for temperature and humidity can be configured as described in section 5 4 temperature and humidity sensor Please place the sensor
11. er yer yer X There is more than one external key switch connected Up to one external key switch can be connected 8 KESL Jor Jer St Jor Jer St Jor XX XX X yer yor Jer yor Jerk Jer yer SE An error occurred during the configuration of the GSM module Please restart the controller 18
12. f the housing is opened an alarm is triggered immediately and you will be notified with an SMS In order to prevent unwanted false alarms ensure that the controller is disarmed before opening the housing 4 6 Reset to factory settings Follow the steps below to reset the controller to the factory settings Connect the controller to the power adapter Set key switch to OFF position Wait for the controller to start up Keep programming key pressed until the error LED red starts flashing quickly Release the programming key and press it again briefly once within the next five seconds If the reset sequence has been correctly performed the controller will restart twice and all values will be restored to the factory settings 4 7 Storing phone numbers Follow the steps below to store your phone number in the controller Connect the controller to the power adapter Set key switch to OFF position Unscrew the lid of the controller Press the programming key once briefly press key only when the controller has started up and the power status LED lights continuously The status LED should now blink slowly If this is the case call the number of the SIM card inserted in the controller Wait until the controller ends the connection The status LED will now light continuously and an SMS is sent to the stored number as an acknowledgement Upon completion of this sequence the number is stored in the controller If you want to store an
13. housing Insert a 9 V block battery in the corresponding battery compartment Important Verify the battery is connected with the correct polarity Set the internal key switch to OFF Plug the power adapter supplied with the system into a wall outlet and connect the other end with the controller Wait for the controller to start up This can be seen from the status LED which stops blinking and lights up continuously Should in addition the error LED light up refer to section 7 error messages Now press the programming key top right once briefly so that the status LED resumes blinking Now you have two minutes while the status LED continues blinking to use your mobile phone to call the SIM card inserted in the controller Let the phone ring until the controller ends the connection If this step is completed successfully the power status LED will again light continuously After a short while you will receive an acknowledgement via SMS Disconnect the controller from the power supply and wait until it has shut down Now fit back the housing lid and tighten its screws Place the controller at a location with good GSM reception o The controller sends an SMS if the reception quality falls below 20 o Ifthe controller is unable to find a network the error LED will light up and indicate the error number 5 see section 7 error messages Now plug in all sensors to be used at the controller The controller is now ready for operation and can be used
14. main telephone number This can also be carried out by sending a configuration SMS When a second number is used all messages are always sent to both numbers Both numbers can be used to carry out configuration changes SMS activation syntax 2nd no phone number of additional mobile phone o Example 2 nr 4123456789 2 nr 4123456789 2 nr 4123456789 Choose one of the three variants to store and activate an additional telephone number SMS deactivation syntax 2nd no enter a 0 zero as phone number o Example 2 nr 0 2 nr 0 2 nr 0 Choose one of the three variants to deactivate an additional telephone number Factory setting 0 deactivated Both commands will be acknowledged after successful completion 10 5 3 Temperature and humidity sensor Following parameters of the temperature and humidity sensor can be configured by sending SMS messages In order to use the sensor for temperature measurements only the humidity function can be disabled by setting the maximum value to 100 and the minimum value to 0 The temperature and humidity ranges are as follows 50 C to 150 C 10 to 95 not condensing Temperature Humidity SMS syntax for the maximum temperature value to trigger an alarm Temp Max maximum temperature in degrees Temp Max 30 Temp Max 30 Temp Max 30 50 C to 150 C o Example Range SMS syntax for the minimum temperature value to trigger an alarm Temp Min mi
15. nimum temperature in degrees o Example Temp Min 2 Temp Min 2 Temp Min 2 Range 50 C to 150 C SMS syntax for the maximum humidity value to trigger an alarm RH Max maximum humidity in percent RH Max 80 RH Max 80 RH Max 80 0 to 100 o Example Range SMS syntax for the minimum humidity value to trigger an alarm RH Min minimum humidity in percent RH Min 30 RH Min 30 RH Min 30 0 to 100 o Example Range Factory settings Maximum temperature Minimum temperature Maximum humidity Minimum humidity 35 C 16 C 100 i e deactivated 0 i e deactivated 11 5 4 Switchable multi socket outlets The following commands can be used to control the switchable multi socket outlets via SMS messages SMS syntax for the multi socket outlets Port port number 1 10 to which the multi socket outlet is connected followed by 1 for on and 0 for off o Example for switching on a multi socket outlet connected to port 3 Port3 1 Port3 1 Port3 1 o Example to switch off a multi socket outlet connected to port 3 Port3 0 Port3 0 Port 3 0 The controller sends back an acknowledgement upon successful completion of the command 5 5 Alarm delay This option is used to set two parameters On the one hand the time between the arming command key switch to ON position and the actual arming of the controller On the other hand the time after an alarm
16. number 10 5 3 Temperature and humidity sensor ie anin ea a aaao aka aa E aaea 11 5 4 Switchable multi socket outlets ssesssesssesssssssssssssssssssssnsssnsssnnssrnssnnssrssesnsssnnesnnesnnesnnesenees 12 5 5 Alarm Ke UE 12 5 6 Additional security configuration c cccssccesscecssscessessseecseseecseeessaecsesecscoeeessaesssaeesensesses 12 Ee 13 6 1 SIMOKE SEN DE 13 6 2 Switchable multi socket outlert ee eee ceseseceeseeceeeeeeaecesaeceeaeeceeeeeesaeeeeaaeeeeeeeecsaeeeeaaeeeeaeeeneees 13 6 3 dl ee TEE 14 6 3 1 Additional settings on the motion Sensor ssssssssessssssssenresssssserernrssssesrnesrnesnssesreenn 15 6 4 VUE ET 16 6 5 External key Wite hea iaai DEENEN cess 16 6 6 Magnetic Contact icsccscciin cand wciten asin idieee eae oth ieee evade EEEE iE aE EAEE da eia 17 6 7 Temperature and humidity sensor 17 Z IESSEN ANEN 18 1 Description Thank you very much for purchasing the G Systems SMS alarm controller The controller is an easy to use standalone alarm system with alarm output via SMS The device provides ten independent input output ports By virtue of its many sensors and its individual terminal assignment the controller meets all requirements The controller offers additional functions such as the option to store a second phone number and to switch any standard 230 V device on or off via SMS 1 1 Functions Alarm via SMS O Ov O O O 0 Er E Smoke detector Motion detector Water sensor
17. onnected to the mobile phone network Security status 3 This is a combination of the settings 1 and 2 Alarms are sent as numerical codes and the controller connects to the mobile phone network only when required to send an alarm Replies during the configuration process continue to be sent in text format Since a connection needs to be made at first the despatch of alarm messages is delayed by approximately 30 seconds Section 5 7 additional security configuration describes in detail the syntax to be followed for sending the configuration to the controller Important If the security status is 1 or 3 the controller will not be able to receive or process any messages This means that no further settings can be made In order to re establish the communication with the controller the key switch must be operated as described below Key switch sequence to connect to the mobile phone network from OFF position ON OFF ON OFF and from ON position OFF ON OFF This sequence must be completed within two seconds The controller connects to the network as soon as this command is entered the connection will be established within approximately 20 s and the controller can now be configured As soon as the alarm is armed ON the controller will disconnect from the network 4 8 1 Numerical codes Numerical Numerical code Description alarm code Description alarm 10 Smoke sensor 34 Lamp over tem
18. ops blinking only when the controller is disarmed and the key switch is set to OFF o A slowly blinking LED indicates that an external key switch is connected to the port and set to OFF position 4 3 Internal key switch The controller can be armed on or disarmed off by means of the internal key switch When the switch is set to ON the controller will be armed after the specified delay time This delay time allows the user to leave the room without generating an immediate alarm The delay time can be configured through an SMS command See section 5 6 alarm delay Once the delay time has expired the controller changes to armed mode When the switch is set to OFF the controller is disarmed immediately All alarms are reset and the control system changes over to the disarmed mode 4 4 Backup battery A 9 V block battery must be inserted in the housing in order to prevent the armed controller from shutting down in the event of a power failure or when the power supply is disconnected If the power supply is no longer available while the controller is armed and with a backup battery inserted in the controller an alarm message will be sent via SMS Subsequently the controller shuts down until the power supply is restored It should be noted that without mains supply the sensors are no longer operative and the power supply to the controller needs to be checked on site 4 5 Housing protection When the controller is armed and the lid o
19. ortant At first verify that the sensor has been disconnected and is no longer energised When the housing is open take care not to touch the printed circuit board Three jumper sockets 1 2 3 see figure below allow to change the following settings 1 LED jumper This jumper is used to define whether the internal LED should light up during an alarm o Jumper connecting 1 amp 2 LED lights up during alarm and calibration o Jumper connecting 2 amp 3 LED always off 2 Relay jumper This jumper must connect 2 amp 3 or be set to N C Otherwise a correct functioning with the controller cannot be guaranteed 3 Pulse jumper This jumper can be used to define how sensitive the controller is when reacting to movements o Jumper connecting 1 amp 2 The motion sensor is set to maximum sensitivity o Jumper connecting 2 amp 3 The sensitivity is set to a medium level In addition the high frequency suppression is set to high o Jumper open shut off The sensitivity is low and the High frequency suppression is set to high OOOO OO LED JUMPER x ir Lo bes Les Ke jo T Ka 1 Q RELAY JUMPER en eo N bo w PULSE JUMPER N go wo 15 6 4 Water sensor The water sensor triggers an alarm upon the contact with water It can for instance be placed on the floor to trigger an alarm in the case of the room being flooded with water The water sensor has two sides The top side with markings
20. perature sensor removed 11 Water sensor 35 Temperature and humidity sensor removed 12 Reed switch 36 External key switch has been removed 13 Motion sensor 37 Switchable multi socket outlets removed 14 Lamp over temperature 50 Controller opened 15 Over temperature 51 Power failure controller to standby 16 Under temperature 52 Low battery voltage 17 Humidity too high 53 No battery connected 18 Humidity too low 54 Poor SMS reception 30 Smoke sensor removed 55 Programming key activated 31 Water sensor removed 56 Key switch inserted 32 Reed switch removed 57 Wrong key position See user manual 33 Motion detector removed 4 8 2 Overview Security index Description 0 1 2 3 X X Alarms will be sent as text messages X X Alarm will be sent as numerical codes X X The controller is permanently connected to the mobile phone network X X Controller connects to the mobile phone network for alarms only 5 SMS commands Almost all controller settings can be made via SMS As regards the SMS communication between user and controller one should keep in mind that each SMS must not comprise more than 160 characters The controller does not support multi part SMS Most of the samples listed below show three variants These three variants show examples how to apply the command You may opt for one variant there is no need to send all three SMS variants As an alternative you may send multiple SMS commands within one SM
21. rtant The maximum permitted current is 10 A at cos 1 13 6 3 Motion sensor The motion sensor is a passive infrared motion detector The sensor detects the movement of a human or animal in the controlled zone The sensor provides a thermal compensation as well as a white light and high frequency suppression Technical data Detection angle 110 Detection range 12m HF suppression 10 MHz 1 GHz at 20 V m Sensor Dual element infrared sensor Installation height 1 7 m to 2 5 m recommended height 2 2 m Temperature range 0 C to 50 C Humidity range 0 to 95 Installation 1 Use the included screws to fasten the holder to the wall at a suitable location The sensor should not be mounted near to doors leading to the outside or near to pets direct sun radiation or moving objects 2 Fit the motion detector to the holder 3 Route the cable to the controller and connect it to a free port 4 After connecting to the controller the sensor requires approx 60 seconds to start up and perform a self calibration 5 Subsequently its functioning can be tested Information Never touch the sensor element inside the housing Clean the sensor every few months with a soft brush Operating range 14 6 3 1 Additional settings on the motion sensor The sensitivity and the internal LED can be adjusted at the motion detector In order to carry out these adjustments the housing of the motion detector has to be opened Imp
Download Pdf Manuals
Related Search