Quick Install Guide - EZ
Contents
1. TYCON systems EZ Base High Performance 250mW Outdoor Base Station Client with integrated 15 hour battery backup Integrated battery backup for powerline filtering and 24 7 operation Achieve up to 15 Mbit sec speed 25Mbps for 5GHz version Includes TriBand omni antenna for up to 0 3miles range Add external antenna for up to 20 miles Field Proven Wireless Technology Solar Ready _ ic c j STOP DANGER Avoid Powerlines ARA You Can Be Killed When following the instructions in this guide to install the device take extreme care to avoid contact with overhead power lines lights and power circuits Contact with power lines lights or power circuits may be fatal We recommend to install device no closer than 20 feet to any power lines Safety For your own protection follow these safety rules Perform as many functions as possible on the ground 2 Do not attempt to install the device on a rainy windy or snowy day or if there is ice or snow accumulation at the install site or if the site is wet 2 Make sure there are no people pets etc below when you are working on a roof or ladder Watch out for any power lines which may be overhead under ground or behind walls keeping safely clear of them with the antenna ladders or any tools See appendix for FCC RF exposure guidelines Recommended Tools Phillips Screwdriver 3mm Allen Wrench 14mm Open End Wrench Screws and screwdriver if mounting to a w2. This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be deter mined by turning the equipment off and on the user is encouraged to try to correct the interference by one of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help e FCC Caution Any changes or modifications not expressly ap proved by the party responsible for compliance could void the user s authority to operate this equipment This device complies with Part 15 of the FCC Rules Operation is sub ject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including inte
3. about 35 clients per access point The EZ Base can handle up to 50 but perfor mance will be degraded with too many concurrent clients 8 POWER CYCLING THE RADIO BOARD Because this is a bat tery backup system the only way to cycle power on the Radio Board is to open the enclosure and disconnect one of the battery wires from the controller The other way is to unplug the POE Power supply from the AC source and waiting 15 hours for the controller to turn off power to the radio board The Radio board can be rebooted through the web interface either through the wireless side or Ethernet side You can also reboot the unit from the Discovery Tool 9 COMMON MICROWAVE BARRIERS Tinted windows are made by applying a metalized film to the window If a window has tinting it will 9 usually block the microwaves and cause reduced performance of the EZ Base Concrete walls are also a significant barrier to microwave signals Aluminum siding on houses is also a barrier to microwave sig nals Wood frame houses covered with brick or stucco are pretty trans parent to microwave signals and they will reduce the signal strength but the signal will still pass thru the structure We are bringing this up to you so you can better understand possible causes of performance issues 10 VOICE OVER IP VOIP The EZ Base supports all VOIP stand ards making it possible to use VOIP phones across any EZ Base link We recommend setting the Data Rate t
4. please retrieve the documentation online at http ez bridge com support support htm TECH CORNER Additional Information you may find useful 1 RAIN SNOW ICE The frequencies being used by the EZ Base will not be affected by heavy rain or falling snow You should not see any performance degradation due to inclement weather 2 LIGHTNING Lightning is the single worst enemy of outdoor elec tronics equipment No electronics will survive a direct strike but there are close proximity strikes that can cause huge electrical fields to be generated which can damage electronic equipment We have taken special care in the design of the EZ Base unit to ensure proper grounding of the electronics inside the enclosure to prevent damage from electrical storms Always use DC grounded antennas Make sure that the POE Power Supply is plugged into a surge protected outlet such as a surge protected power strip or UPS inside the house Shield ed CAT5 cable is also recommended between the POE Inserter and the 8 EZ Base 5 INTERFERENCE The most common cause of poor performance is due to interference from other wireless devices in the area Interference can cause poor throughput and in the worse case a lockup It s always good to do a site survey using the EZ Base control panel to see what other wireless devices are in the area and then choose a wireless chan nel that is at least 2 channels away from any strong offending signal Ke
5. router the firewall is on the wireless side so inbound wireless traffic is routed thru the firewall To access the device you need to be connected thru the Ethernet port 5 SECURITY Security is not configured by default After you get the system working the way you want we recommend assigning adminis trator user name and password and also setting wireless security by changing the encryption settings WPA AES is the most advanced security type and is recommended for most WDS or Point to Point ap plications Because most WiFi clients don t support WPA encryption use WEP if setting up a WiFi AP hotspot 6 SITE SURVEY The site survey is a very useful tool to determine what wireless devices are within range of your EZ Base and could be a source of interference that could cause degraded performance Go to WIRELESS and then click on SITE SURVEY then REFRESH The list will show all wireless devices including channel MAC Address and relative signal strength of all the devices within the range of the EZ Base Te chn ica Specifica tions Note Subject to Change Without Notice 2 4GHz 5GHz Standards 802 11b g 802 11a Certifications FCC CE Operating Frequency 2400 to 2497MHz 5100 to 5875MHz 00 5100 to 5875MHz 5875MHz Available Transmit Power 802 11b 100 to 250mW 10 to 250mW software selectable 802 11g 50 to 100mW 73 54Mbps 74dBm 54 Mbps 84 11Mbps 94dBm 6 Mbps 64 1280 WEP WPA WPA2 Remote Configurati
6. all NOTE You should be familiar with using tools such as these before attempting installation of the device You should be comfortable with working on a ladder So Getting Started Y It is recommended that you setup the EZ Base system in your office or lab to get acquainted with the operation of the unit before installing outdoors It s always best to start with a fully charged battery Controller won t power the wireless card unless the battery voltage is gt 12V Recharging a dead battery with the controller and power supply may take 4 hours You can charge faster with a standard auto charger to get started X Please help preserve the environment and return used batteries to an authorized depot x 2 STEP 1 Install The Battery Remove any screws attaching holding plate to enclosure Connect bat tery wires from controller to battery terminals Observe proper polari ty Gently lift holding plate and insert battery into enclosure with termi nals toward right hand side Secure holding plate with 7 screws STEP 2 Mount the EZ Base Choose a mounting location with good line of sight to the remote loca tions Install two bracket pieces to back of enclosure using 4 screws The bracket can be mounted to a wall or to an existing pole up to 2 diameter The EZ Base can also be mounted indoors if desired TECH TIP Microwaves travel in straight lines and they lose strength quickly when going thru buildings and trees If
7. ep in mind that even though alls well today somebody could setup a new system and create interference with your system at any time If you suspect interference change channels There is also a Watchdog Tim er built into the EZ Base which you can set to ping a remote device If connection is lost the unit will automatically reboot This is useful if you experience frequent lockups Lowering the Beacon Interval on the Wire less Advanced Settings page can help improve performance in areas of intense interference 6 RANGE Useable distance with the included omnidirectional an tenna is about 500yds at 5GHz and up to about 1 mile at 2 4GHz To get more distance from the EZ Base you will need to use an external antenna which you can purchase from any of our distributors A good 24dBi antenna should give about 15 miles distance The practical limit is about 20 miles due to the curvature of the earth unless the equipment is mounted on a tall tower or mountain The ACK timing default in the Wireless Advanced Settings page is 91 When the software sees the default value of 91 it actually switches to auto mode and ACK timing will be set automatically based on the best settings for the actual distance If you over ride the default value the software will use the value that you entered This is also true of other timing settings We highly recom mend leaving these settings at default for best performance 7 ACCESS POINT CAPACITY We recommend a max of
8. ler Notes 1 When a battery is connected to the controller and the battery volt age is gt 12V the LOAd LED should be on 2 When the POE power supply is plugged in and CAT5 cable con nected to POE IN the POE LED should be on 3 If LOAd LED is off because battery voltage is lt 12V it should come back on when battery is charged to gt 12V 4 Controller is attached using Velcro fasteners so it is removable 4 5 There is a secondary 12V output on the controller to power addi tional 12V devices 6 Controller has a optional solar input for a 12V solar panel up to 120W Adding a solar panel can extend the backup time Software Settings 1 There is an HTML management system built into every EZ Base unit which is accessed thru a standard web browser The unit can com municate thru the CAT5 ethernet cable connection or thru the wireless connection so you can manage remote units from a single location NOTE The device will usually go into a 2 minute reboot cycle When clicking on APPLY CHANGES During this time it will be unresponsive 2 IP ADDRESS The first thing you want to do is reset the IP ad dress to match the subnet of your network Be careful not to cre ate any IP address conflicts Default IP address for the EZ Base is 192 168 1 1 To access the EZ Base with your browser your comput er IP address must be on the same subnet ie 192 168 1 xxx The EZ Base ships with DHCP client enabled so if the unit has acce
9. o a fixed value when using VOIP if clicking is heard in the VOIP You can set data rate to a fixed value on the Wireless Advanced Settings page 11 TYPICAL APPLICATIONS a WiFi Hotspot create a Wifi hotspot for patios campuses caf s yards hotels etc b Repeater Extend your network c Community Wireless Provide internet access to multiple hous es or commercial buildings d Marina Wireless Provide internet access to a marina e Campground Access Provide internet access for a seasonal campground or recreation area f Internet access sharing share internet access with a friend or family member g Link a Home Office to a Main Office you can access shared files and folders as well as print to the main office printers and use other shared network devices remotely Link networks in multiple buildings together Add a high speed link between your home network and a PC in your remote studio or office which is located in an outbuilding on your property j Create a secure link for remote video and network based security cameras The EZ Base works with all network based security cameras Create a streaming video conference link between buildings Be cause of the high bandwidth available with the EZ Base it easily supports streaming video technologies used for remote conferencing like church meetings business meetings etc a x Appendix Federal Communication Commission Interference Statement
10. on By IP Address thru Wireless or Ethernet Antenna Beamwidth H V 360 90 deg 360 90 deg Receive Sensitivity Recharge Time 4 Hours Typical Power Over Ethernet INPUT 100 240VAC 50 60Hz Power Supply OUTPUT 24VDC 2 5A Mount gt Pole up to 2 dia or Wall Operating Temperature 31 to 140Deg F 35 to 60 Deg C Humidity 0 to 100 RH Auer aie NEB 100MPH 23lbs 125MPH 35lbs 7 FACTORY DEFAULTS If at any time the system stops working be cause of changes made to the settings you can get back to the original settings by resetting to factory defaults Go to ADMIN Reset Settings to Defaults Any customized settings will be lost once this process is initiated If you cannot access the web page on the unit you can do a manual reset Open the cover of unit Power up the unit wait 2 mins press and hold the black reset button for 15secs release and wait 2 mins for re boot 8 UPGRADE FIRMWARE For the latest firmware point your browser to http http ez bridge com sup bridge com support support htm Download the latest firm ware to your PC Select UPGRADE from the menu and then browse for the new file Advanced Features The EZ Base has many advanced features if more functionality is desired To access the advanced features click on Advanced Web at the top of the menu tree This will activate the advanced menu options Since documentation for these advanced modes is too extensive to cover here
11. rference that may cause undesired operation IMPORTANT NOTE FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment This equipment should be installed and operated with minimum distance 20cm between the radiator amp your body The antenna s used for this transmitter must not be co located or operating in conjunction with any other antenna or transmitter Limited Warranty All Tycon Systems wireless products are supplied with a limited 12 month warranty which covers material and workmanship defects This warranty does not cover the following a Parts requiring replacement due to improper installation misuse poor site conditions faulty power etc 11 a Lightning damage a Physical damage to the external amp internal parts 2a Products that have been opened altered or defaced a Water damage for units that were not sealed or mounted according to user manual a Units that were not properly grounded a Usage other than in accordance with instructions and the normal intended use Do not return any products until you receive a Return Material Authori zation RMA number Products received without a valid RMA number will be rejected and returned to sender Warranty Repairs All returns must have a valid RMA number written clearly on the outside of the box Without an RMA number the shipment will be refused For customers located in United State
12. s and Canada customer pays all shipping charges incurred to ship the product to Tycon Systems Tycon Systems pays shipping charges to return the product to the original pur chaser For all other countries the original purchaser shall pay all ship ping broker fees duties and taxes incurred in shipping products to and from Tycon Systems Provided the goods have not been modified or repair attempted by someone other than Tycon Systems at the option of Tycon Systems products may be returned either as repaired or re placed If it is determined that there is no fault found NFF on a unit within warranty the customer will be charged 75 USD for testing time For products out of warranty the standard NFF charge is 200 This charge will be at the discretion of Tycon Systems The RMA number is valid for 14 days from date of issue The product must be received by the repair depot within these 14 days or the shipment may be refused Shipping and Damage Claims All shipping damage claims are the purchaser s responsibility Inspect each shipment upon delivery and IMMEDIATELY report all damage to the carrier There may be time limits and inspections may be required Phone 801 432 0098 support ez bridge com 8000017 Rev 3 EZ Base Qwik Install Guide 12
13. ss to your network it will get its IP address automatically from your network To find the units IP address use the Discovery Tool S TECH TIP Download the EZ Discovery Tool from http ez bridge com support support htm This tool will assist you in finding the EZ Base on the network and allow you to change the IP address or set it as a DHCP client Just select the unit click on IP DETAILS make selections and save changes directly to the device 3 WIRELESS MODE The EZ Base comes in Access Point AP mode by default The EZ Base can be configured as an AP or Client or WDS or AP WDS or Point to Point It also can be configured as a repeater AP Communicates with multiple 802 11 clients in a point to multipoint configuration Typically the AP can service about 30 clients Client Communicates with any 802 11 AP in a point to multipoint con figuration Security must be set to match the AP security before trying to connect WDS Communicates with up to 4 other WDS devices to create trans parent bridging between several points Communicates on MAC layer To setup WDS you need the units to be on the same wireless channel they must have the same WDS security settings Enter unit A s MAC address into Unit B s WDS table and vice versa AP WDS Used to create a bridge that also acts like an AP The de vice communicates with another WDS device thru a WDS bridge and then broadcasts the signal as an AP to allow client de
14. there are objects in the microwave path then useable distance will be reduced 2 4GHz penetrates objects better than 5GHz STEP 3 Install a CAT5 cable between the included POE inserter power supply through the RJ45 Feedthru and to the bottom RJ45 con nector on the controller labeled POE IN CAT5 cable can be up to 300 100m in length NOTE We highly recommend using shielded CAT5 cable for outdoor runs to prevent EM surges from lightning from damaging the Ethernet port on the wireless device 3 To Switch Computer Router 2 etc To Power Supply i To EZ Base STEP 4 Tighten the RJ45 Feedthru onto the Cat5 cable If the cable diameter is too small to make a good seal wrap a couple turns of elec trical tape around the CAT5 cable at the seal area to increase it s diam eter STEP 5 Make sure lid gasket is clean and free from any particles then carefully close the cover making sure that wires are clear of the seam and hinge area STEP 6 Tighten the 4 seal screws evenly to seal the cover STEP 7 Install antenna that came with the unit or a larger gain external antenna The small antenna that is supplied with the EZ Base is good for about 500 yds To cover greater distances you will need to use a larger antenna A 24db antenna should provide over 15 miles of cover age The practical limit is about 12 miles because of the curvature of the earth unless the antennas are mounted at a higher elevation Control
15. vices to connect Security for WDS and AP are set independently AP WDS would be used when there is a single internet source and multiple AP s are need ed to cover a wide area with WiFi coverage For a successful WDS set up see WDS above Point To Point Creates a point to point transparent bridge between two points This is normally used to connect two buildings or to create a backhaul between two points To create a successful Point to Point set up both units must be on the same wireless channel set to same secu rity settings Enter Unit A s MAC address into Unit B s BSSID field and vice versa Repeater The AP picks up a signal from another wireless AP and re broadcasts it to another location This is useful if a signal needs to turn a corner around an impenetrable object or to increase the range To setup the repeater enter the remote AP s SSID into the Repeater SSID field and enter the remote AP s MAC address into the Repeater BSSID Field 4 NETWORK OPERATION MODE The default is for operation mode to be set to BRIDGE A bridge passes all network traffic between the wireless and Ethernet ports of the device This is the most common use The EZ Base can also be set to ROUTER mode In Router Mode there is a built in firewall and NAT that blocks traffic If in AP mode and set to router then inbound Ethernet traffic is firewalled and to access the device you need to access thru the wireless side If in Client Mode and set to
Download Pdf Manuals
Related Search