Invacare Mobile Recliners
Contents
1. Owner s Operation and Maintenance Manual Invacare Mobile Recliners Three Position Recliner Model 1H6074A Deluxe Three Position Recliner Model H6065 series Clinical Recliner Model 1H6077A DEALER This manual MUST be given to the user of the product USER BEFORE using this product read this manual and save for future reference Yes you can A WARNING A QUALIFIED TECHNICIAN MUST PERFORM THE INITIAL SET UP OF THIS RECLINER ALSO A QUALIFIED TECHNICIAN MUST PERFORM ALL PROCEDURES IN THE SERVICE MANUAL RECLINER USERS DO NOT SERVICE OR OPERATE THIS EQUIPMENT WITHOUT FIRST READING AND UNDERSTANDING 1 THE OWNER S OPERATOR AND MAINTENANCE MANUAL AND 2 THE SEATING SYSTEM S MANUAL IF APPLICABLE IF YOU ARE UNABLE TO UNDERSTAND THE WARNINGS CAUTIONS AND INSTRUCTIONS CONTACT INVACARE TECHNICAL SUPPORT BEFORE ATTEMPTING TO SERVICE OR OPERATE THIS EQUIPMENT OTHERWISE INJURY OR DAMAGE MAY RESULT DEALERS AND QUALIFIED TECHNICIANS DO NOT SERVICE OR OPERATE THIS EQUIPMENT WITHOUT FIRST READING AND UNDERSTANDING 1 THE OWNER S OPERATOR AND MAINTENANCE MANUAL 2 THE SERVICE MANUAL IF APPLICABLE AND 3 THE SEATING SYSTEM S MANUAL IF APPLICABLE IF YOU ARE UNABLE TO UNDERSTAND THE WARNINGS CAUTIONS AND INSTRUCTIONS CONTACT INVACARE TECHNICAL SUPPORT BEFORE ATTEMPTING TO SERVICE OR OPERATE THIS EQUIPMENT OTHERWISE INJURY OR DAMAGE MAY RESULT NOTE Updated versions of this man2. tq daa 3l LIMITED WARRANTY 000000000000000000000000000000000000000000000000000000000000000000000 32 REGISTER YOUR PRODUCT The benefits of registering MN Safeguard your investment Ensure long term maintenance and servicing of your purchase Receive updates with product information maintenance tips and industry news Invacare can contact you or your provider if servicing is needed on your product It will enable Invacare to improve product designs based on your input and needs Register ONLINE at www invacare com Or Complete and mail the form on the next page Any registration information you submit will be used by Invacare Corporation only and protected as required by applicable laws and regulations Part No 1141494 4 Invacare Mobile Recliners Cut Along Line PRODUCT REGISTRATION FORM Register ONLINE at www invacare com or Complete and mail this form Name Address City State Province Zip Postal Code Email Phone No Fold ME S 2 I LOIALLLInLII here Invacare Model No Serial No Purchased From Date of Purchase Method of purchase check all that apply L Medicare Insurance M Medicaid Other 2 This product was purchased for use by check one Self Parent Spouse Other 3 Product was purchased for use at L Home Facility Other 4 purchased an Invacare product because Price Features list features
3. NOTE The footrest assembly will elevate automatically as the chair is reclined NOTE The occupant should not be required to exert excessive force to change recline positions If the recliner exhibits difficulty in reclining an attendant should be called for assistance DETAIL A RECLINE DETAIL B RECLINE POSITION I DIALYSIS POSITION 2 SHOCK e FIGURE 4 3 Reclining the Chair Model IH6077A User Recline Invacare Mobile Recliners 18 Part No 1141494 SECTION 4 OPERATION Assisted Recline NOTE For this procedure refer to FIGURE 4 4 1 Grasp the push bar with one hand 2 Squeeze on the gas spring release handle with the other hand 3 Lower the chair back slowly down into either recline position 1 Dialysis or recline position 2 Shock position 4 Release the gas spring handle NOTE If the cylinder does not unlock when the lever is actuated or remains permanently unlocked when the lever is not actuated cable tension must be adjusted Refer to Adjusting Gas Spring Recline Cylinder Assembly Model IH6077A Only on page 26 DETAIL RECLINE POSITION I DIALYSIS Push Bar Gas Spring DETAIL A Release Handle RECLINER DADA Mut l te te DETAIL RECLINE POSITION 2 SHOCK FIGURE 4 4 Reclining the Chair Model IH6077A Assisted Recline Positioning the Articulating Headrest NOTE For this procedure refer to FIGURE 4 5
4. 5 Who referred you to Invacare products check all that apply Doctor Therapist Friend Relative Dealer Provider Other L Advertisement circle TV Radio Magazine Newspaper LI No Referral 6 What additional features if any would you like to see on this product Fold 7 Would you like information sent to you about Invacare products that may be available for here particular medical condition L1 Yes No If yes please list any condition s here and we will send you information by email and or mail about any available Invacare products that may help treat care for or manage such condition s 8 Would you like to receive updated information via email or regular mail about the Invacare home medical products sold by Invacare s dealers L1 Yes No 9 What would you like to see on the Invacare website 10 Would you like to be part of future online surveys for Invacare products Yes LI No User s Year of birth If at any time you wish not to receive future mailings from us please contact us at Invacare Corporation CRM Department 39400 Taylor Parkway Elyria OH 44035 or fax to 877 619 7996 and we will remove you from our mailing list To find more information about our products visit www invacare com Fold here Fold here BUSINESS REPLY MAIL FIRST CLASS MAIL PERMIT NO 196 ELYRIA OH POSTAGE WILL BE PAID BY ADDRESSEE INVACARE CORPORATION CRM DEPARTMENT 39400 TAYLOR
5. Headrest 1 Grasp the headrest and push or pull it into the desired position FIGURE 4 5 Positioning the Articulating Headrest Part No 1141494 19 Invacare Mobile Recliners SECTION 4 OPERATION Locking Unlocking the Rear Wheels NOTE For this procedure refer to FIGURE 4 6 1 Push down on the wheel lock mechanism to engage the wheel locks 2 Release the wheel locks by pushing the other side of the lock mechanism downward Locking Unlocking Wheel Lock Wheel Lock Mechanism Mechanism FIGURE 4 6 Locking Unlocking the Rear Wheels Installing Storing the Tray Model IH6074A NOTE For this procedure refer to FIGURE 4 7 NOTE Reverse this procedure to remove the tray 1 Pull down on the plunger release knobs on both arms and twist them to lock them in the open position 2 Pull the tray forward and clear from the hanger located on the side of the recliner 3 Align the alignment rods with the mounting brackets under the armrests of the recliner 4 Insert the alignment rods into the mounting brackets 5 Slide the tray to the desired position until an audbile click is heard DETAIL FRONT VIEW DETAIL SIDE VIEW Mounting Bracket Hidden from View Tray Armrest Alignment Rod Plunger Release Knob Alignment Rods Mounting Bracket Alignment Rod FIGURE 4 7 Installing Storing the Tray Model IH6074A Invacare Mobile Recliners 20 Part No 1141494 Model IH6
6. SECTION 4 OPERATION 0000000000000000000000000000000000000000000000000000000000000000 17 Reclining the 17 Models IH6074A and IH6065 series eee estes ee eeeteeeettn teta tete ta tentato nta tonnene 17 1 6077 Cem er 18 Positioning the Articulating Headrest eee eee eene tenerent ron tntn statu tnta tonta nis 19 Locking Unlocking the Rear Wheels eee eese esee tete teat ttetn tate tntnttnute 20 l stalling Storing the T Tay baden vies nien 20 Model 196074 E M 20 Model Ig 1057 TRE 21 Model lH6077 Aza detiene o A a E 21 Adjusting the Tray Position estis datant o e Lo ERA Ren De EE Hep D RA 22 Part No 1141494 3 Invacare Mobile Recliners TABLE OF CONTENTS TABLE OF CONTENTS SECTION 5 MAINTENANCE 0000000000000000000000000000000000000000000000000000000000 23 Replacing the dice deo topic ia eive eae dei tod etus 23 Model IH6074A and IH6065 series no do 23 Model 607 f MA 24 Replacing the Footrest ertet dede ded debe esa dde 24 Replacing the Recline Mechanism Guard eee 25 Replacing the Elbow Pads Model IH6
7. C and D Securely tighten 9 Install the side panel Refer to Removing Installing the Side Panel on page 30 10 Place chair in the upright position NOTE If binding or pinching of recline mechanism guard occurs contact Invacare 11 Carefully tip recliner onto the left side Ensure there are no obstructions on or around the floor before doing this 12 Repeat STEPS 3 10 to install remaining recline mechanism guard Part No 1141494 25 Invacare Mobile Recliners SECTION 5 MAINTENANCE Side View Rear of Chair Front of Chair Seat Cushion Side Frame Footrest DO NOT Remove This Bolt Recline Mechanism Guard FIGURE 5 4 Replacing the Recline Mechanism Guard BotA BoltD Replacing the Elbow Pads Model 1H6077A Only NOTE For this procedure refer to FIGURE 5 5 1 Elbow Remove two hex head screws that Pad secure the existing elbow pad to the elbow pad bracket Elbow Pad Remove existing elbow pad and Bracket discard J Hex Head Screws FIGURE 5 5 Replacing the Elbow Pads Model IH6077A Only Using the existing hex head screws secure the new elbow pad to the elbow pad bracket Adjusting Gas Spring Recline Cylinder Assembly Model 1H6077A Only NOTE For this procedure refer to FIGURE 5 6 on page 27 1 2 3 a 6 7 Remove the mounting screw which secures the cable to the back assembly Remove the retaining ri
8. PARKWAY ELYRIA OH 44035 9836 Invacare Product Registration Form Please Seal with Tape Before Mailing NO POSTAGE NECESSARY IF MAILED IN THE UNITED STATES Cut Along Line LABEL LOCATION LABEL LOCATION Models 1H6074A IH6065 series and 1H6077A DO NOT allow children to play on or operate the DO NOT press recliner The legrest falls down upon closing so down stand that a child could possibly be injured on the footrest Keep hands and feet clear of mechanism 1143178 Rev A 4 25 06 When unoccupied ensure the legrest is down 1143177 Rev A 4 25 06 NOTE Model IH6074A shown IH6065 series and IH60774A labels are in the same locations Part No 1141494 7 Invacare Mobile Recliners SPECIAL NOTES SPECIAL NOTES Signal words are used in this manual and apply to hazards or unsafe practices which could result in personal injury or property damage Refer to the following table for definitions of the signal words SIGNAL WORD MEANING Danger indicates an imminently hazardous situation which if not avoided DANGER will result in death or serious injury Warning indicates a potentially hazardous situation which if not avoided WARNING could result in death or serious injury Caution indicates a potentially hazardous situation which if not avoided CAUTION may result in property damage NOTICE THE INFORMATION CONTAINED IN THIS DOCUMENT IS SUBJEC
9. Recliners SECTION 2 SAFETY INSPECTION SECTION 2 SAFETY INSPECTION NOTE Every six months or as necessary take your recliner to a qualified dealer for a thorough inspection and servicing Regular cleaning will reveal loose or worn parts and enhance the smooth operation of your recliner To operate properly and safely your recliner must be cared for appropriately as any other vehicle Routine maintenance will extend the life and efficiency of your recliner Safety Inspection Checklists CAUTION As with any transport device casters should be checked periodically for cracks and wear and should be replaced as necessary Initial adjustments should be made to suit your personal body structure needs and preference Thereafter follow these maintenance procedures Inspect Adjust Initially Q Ensure that the recliner rolls straight no excessive drag or pull to one side Q Ensure seat back and or armrest upholstery have no rips and do not sag Replace if necessary Ensure that the seat upholstery is fastened to the seat frame Clean seat upholstery armrests Inspect caster assembly to ensure it has proper tension when caster is spun Caster should come to a gradual stop Loosen tighten caster locknut if wheel wobbles noticeably or binds to a stop Ensure that the caster assembly is free from debris Inspect for any loose hardware on the recliner Check that all labels are present and legible Repl
10. SOLELY DETERMINED BY INVACARE THE WARRANTY SHALL NOT APPLY TO PROBLEMS ARISING FROM NORMAL WEAR OR FAILURE TO ADHERE TO THE INSTRUCTIONS IN THIS MANUAL THE FOREGOING WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS WARRANTIES IMPLIED WARRANTIES IF ANY INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE SHALL NOT EXTEND BEYOND THE DURATION OF THE EXPRESSED WARRANTY PROVIDED HEREIN AND THE REMEDY FOR VIOLATIONS OF ANY IMPLIED WARRANTY SHALL BE LIMITED TO REPAIR OR REPLACEMENT OF THE DEFECTIVE PRODUCT PURSUANT TO THE TERMS CONTAINED HEREIN INVACARE SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES WHATSOEVER SOME STATES DO NOT ALLOW EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGE OR LIMITATION ON HOW LONG AN IMPLIED WARRANTY LASTS SO THE ABOVE EXCLUSIONS AND LIMITATIONS MAY NOT APPLY TO YOU THIS WARRANTY SHALL BE EXTENDED TO COMPLY WITH STATE OR PROVINCIAL LAWS AND REQUIREMENTS Invacare Corporation www invacare com USA Canada One Invacare Way 570 Matheson Blvd E Unit8 Invacare Yes You Can and the Medallion Elyria Ohio USA Mississauga Ontario Design are registered trademarks of 44036 2125 L4Z 4G4 Canada Invacare Corporation 800 333 6900 800 668 5324 9 2006 Invacare Corporation e PRODUCT Part No 1141494 Yes you can MADE IN CHINA Rev A 4 25 06
11. and 2 for the other side panel Installing Side Panel 1 Slip the top of the right side panel into the mounting tab Side 2 Push the side panel upward until the Panel side panel fit into the side frame 3 Pop the side panel into position when the push buttons are visible through Push Buttons the push pin holes near the bottom of the side frame FIGURE 5 11 Removing Installing the Side Panel Invacare Mobile Recliners 30 Part No 1141494 SECTION 5 MAINTENANCE Replacing the Armrest Cushion NOTE For this procedure refer to FIGURE 5 12 Removing Armrest Cushion 1 Remove four screws securing the armrest cushion to the recliner frame M Remove the armrest cushion from the recliner frame Installing Armrest Cushion 1 Align the armrest cushion with the Screws recliner frame 2 Secure the armrest cushion to the FIGURE 5 12 Replacing the Armrest recliner frame with the four screws Cushion Cleaning the Upholstery A DANGER When kerosene or naptha is being used care should be exercised Keep away from fire and flame and use only in a well ventilated area A WARNING Carefully follow cleaning instructions provided with cleaning product DO NOT use paint remover or any liquid brush cleaner NOTE A variety of solvents may be used to clean the upholstery on the recliner dependant upon the severity of the stain The following list should be helpful Ordinary dirt stains Clean upholstery w
12. in the recliner grip the armrests and simultaneously lean body weight back and push forward with your arms until a recline position reached NOTE The footrest will lift automatically when the chair back reclines NOTE The occupant should not be required to exert excessive force to change recline positions If the recliner exhibits difficulty in reclining an attendant should be called for assistance FIGURE 4 1 Reclining the Chair Models 1H6074A and IH6065 series User Recline Part No 1141494 17 Invacare Mobile Recliners SECTION 4 OPERATION Assisted Recline NOTE For this procedure refer to FIGURE 4 2 Position Lock Lever Back Assembly 1 Swing recline lock bar up to chair back and lock into position 2 Grasp the armrest with one hand and the push bar with the other hand 3 Push the back of the chair down slowly Position until a desired position is reached NOTE The caregiver can set recline lock barat FIGURE 4 2 Reclining the Chair Models one of the three locking positions IH6074A and 1H6065 series Assisted Recline Model IH6077A NOTE The position lock lever is not available on model IH6077A NOTE Model No IH6077A has two standard recline positions User Recline NOTE For this procedure refer to FIGURE 4 3 1 While seated in the recliner grip the armrests and simultaneously lean body weight back and push forward with your arms until recline position 1 or 2 is reached
13. injury may occur NOTE For this procedure refer to FIGURE 5 3 on page 25 Invacare Mobile Recliners 24 Part No 1141494 SECTION 5 MAINTENANCE 1 Recline the recliner to raise the footrest Regist Cushion assembly Refer to Reclining the Chair on page 17 Footrest 2 Remove the four hex screws that secure lj 1 Assembly the existing footrest cushion to the recline mechanism 3 Align the four mounting holes of the recline mechanism with the four mounting holes of the new footrest cushion Recline Hex Screws Mechanism FIGURE 5 3 Replacing the Footrest Cushion 4 Using four hex screws secure the footrest cushion to the recline mechanism Replacing the Recline Mechanism Guard NOTE For this procedure refer to FIGURE 5 4 on page 26 NOTE Right and left sides are determined from the user s seated position 1 Engage wheel locks 2 Carefully tip recliner onto the right side Be sure there are no obstructions on or around the floor before doing this 3 Remove the side panel Refer to Removing Installing the Side Panel on page 30 4 Remove four existing bolts A B C and D from side frame as shown in FIGURE 5 4 on page 26 5 Remove existing recline mechanism guard 6 Position new recline mechanism guard against the side frame with the folded edge down 7 Align holes of new recline mechanism guard with holes on side frame 8 Secure new recline mechanism guard to side frame with bolts A B
14. products are specifically designed and manufactured for use in conjunction with Invacare accessories Accessories designed by other manufacturers have not been tested by Invacare and are not recommended for use with Invacare products Weight Limitation The weight limitation for Invacare Mobile Recliners is 250 165 113 6 kg The weight limitation for model IH6065WD Wide Recliner is 400 Ibs 181 44 kg The tray for models IH6074A IH6065A and IH6077A has a weight limitation of 40 Ibs 18 2 kg Recline Option Operated by an Attendant Test the recline feature of the recliner first without an occupant to ensure the gas cylinder is operational DO NOT operate the recline option if the gas cylinder is not operational ALWAYS make sure that the recliner is stable before using the recline option Make sure the patient is properly positioned in the recliner before reclining or inclining to maintain maximum stability and safety When returning the occupant of the recliner to the full upright position more body strength will be required for approximately the last twenty degrees of incline sitting up Make sure to use proper body mechanics use your legs or seek assistance to avoid injury Physical limitations of a user and larger occupants of the recliner can present conditions that can injure the assistant When in doubt assure that additional assistants are present before operating the recline feature Part No 1141494 Invacare Mobile
15. 065A NOTE For this procedure refer to FIGURE 4 8 NOTE Reverse this procedure to remove the tray SECTION 4 OPERATION 1 Pull down on the plunger release knobs on both arms and twist them 4 turn to lock them in the open position 2 Pull the tray up and clear from the hangers located on the side of the recliner 3 Align the alignment rods with the mounting brackets under the armrests of the recliner 4 Insert the alignment rods into the mounting brackets 5 Slide the tray to the desired position until an audbile click is heard DETAIL FRONT VIEW Tray Mounting Bracket Hidden from View iral Ali Mounting Release ignment Knob Rods Plunger Brackets Release Knob Armrest DETAIL SIDE VIEW Tray aa FIGURE 4 8 Installing Storing the Tray Model IH6065A Model IH6077A A WARNING The tray has a weight limitation of 40 Ibs 18 2 kg NOTE For this procedure refer to FIGURE 4 9 1 To lower tray pull out the tray and lower Part No 1141494 21 Eol Oh T wu s FIGURE 4 9 Installing Storing the Tray Model IH6077A Invacare Mobile Recliners SECTION 4 OPERATION Adjusting the Tray Position NOTE For this procedure refer to FIGURE 4 10 NOTE This procedure applies to models IH6074A and IH6065A only NOTE There are seven tray positions on the Invacare Mobile Recliner They range from 9 inche
16. 077A Only ou ceccseeseesessessessesseesessessessssssssssssessessessssseesess 26 Adjusting Gas Spring Recline Cylinder Assembly Model IH6077A 26 Replacing the Release Handle and Cable Assembly Model IH6077A Only 27 Replacing Position Lock Lever Models H6074A and 1H6065 Series 28 Removing Position Lock Level a E 28 Installing Position Lock Lever tton eterne eerte ra oae bane 28 Replacilg Castel da disiuncta tela i educ duda Rd tna preti toda pitur 29 Replacing Caster Asser dedu aodio 29 Replacing Caster ad C t 29 Replacing Plunger Release Knob eerie tentes ta tentat tn 30 Removing Installing the Side Panel re 30 Removing Side PARES doter lei 30 Installing Side Panelin sinansa pera aaia ere 30 Replacing the Armrest Cushion cosensynscnesnivevburyestcanvouspnsevbeteowonstevcensasvnctusotynisnsands 3l Removing Armrest Cushion siajssssssssnsssasssvcssenssconessedestesssvsanoossniavonbonsnienouvodondestusovedosdoseesousskaiv eabeasses 3l Installing Armrest Cushlon eset de 3l Cleaning the ete oot beo toe
17. 7 inches TYPICAL PRODUCT PARAMETERS TYPICAL PRODUCT PARAMETERS MODEL NO IH6065 SERIES 46 inches MODEL NO IH8077A 49 inches OVERALL WIDTH 24 inches 27 inches 3034 inches OVERALL DEPTH UPRIGHT 40 inches 4 inches 38 inches OVERALL DEPTH RECLINE 76 inches 78 inches 74 inches SEAT WIDTH 19 inches Petite 1634 inches Adult 18 inches Wide 22 inches Drop Arm 18 inches inches SEAT DEPTH 19 inches 1934 inches 19 inches SEAT TO BACK HEIGHT 32 inches 32 inches 32 inches SEAT TO FLOOR HEIGHT 21 1 2 inches 21 inches 22 inches SEAT ANGLE RANGE 13 38 11 38 14 35 BACK ANGLE RANGE 28 54 29 55 29 77 OVERALL TRAY LENGTH AND WIDTH 25 15 inches 25 x 15 inches 10 x 19 inches WEIGHT LIMITATION 250 Ibs Petite Adult and Drop Arm 250 Ibs Wide 400 Ibs 250 Ibs PRODUCT WEIGHT 73 Ibs 86 Ibs 89 Ibs SHIPPING WEIGHT Part No 1141494 86 Ibs 105 Ibs 105 Ibs Invacare Mobile Recliners SECTION GENERAL GUIDELINES SECTION I GENERAL GUIDELINES A WARNING SECTION GENERAL GUIDELINES contains important information for the safe operation and use of this product DO NOT use this product or any available optional equipment without first completely reading and understanding these inst
18. AIL A PLASTIC SKIRT Back Cushion Plastic Rear Seat Skirt Frame Hex Screw Crossbrace Mounting Hole Hele Guide Tube Tube Mounting Hole Cw Mounting Hex Head Screws Seat Frame Hole Hex Head Screws Crossbrace Plastic Skirt FIGURE 3 1 Assembling the Recliner Assembling Models 6074 and IH6065 series Assembling Model IH6077A NOTE For this procedure refer to FIGURE 3 2 on page 16 1 Remove back assembly from its carton NOTE Ensure that footrest is in the closed position before installing back assembly 2 B 4 9 Lock the rear wheels Refer to Locking Unlocking the Rear Wheels on page 20 Remove the side panels Refer to Removing Installing the Side Panel on page 30 Position the back assembly over the seat frame as shown in Detail A in FIGURE 32 on page 16 Align the holes in the back assembly brackets with the holes in the seat frame as shown in Detail A in FIGURE 3 2 on page 16 Insert a clevis pin through back assembly bracket and seat frame and secure with a retaining ring as shown in Detail A in FIGURE 3 2 on page 16 Repeat for opposite side Align the gas spring bracket with the holes of the mounting bracket on the center of the seat frame Insert a clevis pin through the gas spring bracket and through the mounting bracket on the seat frame and secure with a retaining ring Lift the plastic skirt mounted on the bottom of the seat 10 A
19. T TO CHANGE WITHOUT NOTICE A WARNING INVACARE MOBILE RECLINER TIE DOWN RESTRAINTS Invacare recommends that Mobile Recliner users NOT be transported in vehicles of any kind while in recliners As of this date the Department of Transportation has not approved any tie down systems for transportation of a user while in a Mobile Recliner in a moving vehicle of any type Invacare Mobile Recliners have not been designed and or tested for seating surfaces or vehicle chairs for occupant use within any type of vehicle It is Invacare s position that users of Mobile Recliners should be transferred into appropriate seating in vehicles for transportation and use be made of the restraints made available by the auto industry To date Invacare does not have nor do we have any say in the recommendation of the manufacture of Mobile Recliner transportation systems MAINTENANCE Maintenance MUST be performed only by qualified personnel Invacare Mobile Recliners should be regularly inspected for worn damaged mechanism guards Chairs with damaged guards MUST be removed from service and repaired Invacare products are specifically designed and manufactured for use in conjunction with Invacare accessories Accessories designed by other manufacturers have not been tested by Invacare and are not recommended for use with Invacare products Invacare Mobile Recliners 8 Part No 1141494 PHYSICAL DIMENSIONS OVERALL HEIGHT MODEL NO IH6074A 4
20. ace if necessary FORIH6077A ONLY Ensure that the trigger release cables completely release and the handles return when released FOR IH6077A ONLY Inspect the gas cylinders for leaking oil LL Inspect Adjust Weekly Q Ensure that the seat upholstery is fastened to the seat frame Q Ensure seat back and or armrest upholstery have no rips and do not sag Replace if necessary Q Ensure that the caster assembly is free of debris Invacare Mobile Recliners 12 Part No 1141494 SECTION 2 SAFETY INSPECTION Q FORIH6077A ONLY Ensure that the trigger release cables completely release and the handles return when released Inspect Adjust Monthly Q Ensure that the recliner rolls straight no excessive drag or pull to one side Q Ensure that the seat upholstery is fastened to the seat frame Inspect caster assembly to ensure it has proper tension when caster is spun Caster should come to a gradual stop Q Loosen tighten caster locknut if wheel wobbles noticeably or binds to a stop Inspect for any loose hardware the recliner Q FORIH6077A ONLY Ensure that the trigger releae cables completely release and the handles return when released Inspect Adjust Periodically Q Ensure recliner rolls straight no excessive drag or pull to one side Q Ensure seat back and or armrest upholstery have no rips and do not sag Replace if necessary Q Clean upholstery and armrests Che
21. charges incurred in replacement part installation or repair of any such product Invacare s sole obligation and your exclusive remedy under this warranty shall be limited to such repair and or replacement For warranty service please contact the dealer from whom you purchased your Invacare product In the event you do not receive satisfactory warranty service please write directly to Invacare at the address on the back cover provide dealer s name address date of purchase indicate nature of the defect Invacare Corporation will issue a serialized return authorization The defective unit or parts MUST be returned for warranty inspection using the serial number when applicable as identification within 30 days of return authorization date Do not return products to our factory without our prior consent C O D shipments will be refused please prepay shipping charges LIMITATIONS AND EXCLUSIONS THE FOREGOING WARRANTY SHALL NOT APPLY TO SERIAL NUMBERED PRODUCTS IF THE SERIAL NUMBER HAS BEEN REMOVED OR DEFACED PRODUCTS SUBJECTED TO NEGLIGENCE ACCIDENT IMPROPER OPERATION MAINTENANCE OR STORAGE PRODUCTS MODIFIED WITHOUT INVACARE S EXPRESS WRITTEN CONSENT INCLUDING BUT NOT LIMITED TO MODIFICATION THROUGH THE USE OF UNAUTHORIZED PARTS OR ATTACHMENTS PRODUCTS DAMAGED BY REASON OF REPAIRS MADE TO ANY COMPONENT WITHOUT THE SPECIFIC CONSENT OF INVACARE OR TO A PRODUCT DAMAGED BY CIRCUMSTANCES BEYOND INVACARE S CONTROL AND SUCH EVALUATION WILL BE
22. ck that all labels are present and legible Replace if necessary Q FORIH6077A ONLY Inspect the gas cylinders for leaking oil Part No 1141494 13 Invacare Mobile Recliners SECTION 3 ASSEMBLY SECTION 3 ASSEMBLY A WARNING After ANY adjustments repair or service and before use make sure that all attach ing hardware is tightened securely otherwise injury or damage may result Assembling the Recliner A WARNING Tighten mounting screws securely Failure to do so may result in bodily injury or damage to the recliner Assembling Models IH6074A and 1H6065 series NOTE For this procedure refer to FIGURE 3 1 on page 15 1 Remove back frame with back cushion from its carton 2 Lock the rear casters Work from the rear of the recliner base NOTE Ensure that footrest is in closed position before installing the back frame with cushion 9 Lift the chair back in an upright position behind the rear seat cross brace m Slide the back tubes into the open tube ends of the rear seat cross brace gi Lift the plastic skirt mounted on the bottom of the seat and align behind the rear seat frame crossbrace Detail A 6 Align the holes in the skirt to the holes in the chair back by fastening the hardware N Securely tighten the two hex screws to secure the back cushion to the back frame Invacare Mobile Recliners 14 Part No 1141494 Rear Seat Frame SECTION 3 ASSEMBLY Back Frame with DET
23. e position lock lever to the seat frame with the two screws nylon washers and locknuts FIGURE 5 8 Replacing Position Lock Lever Models H6074A and 1H6065 Series Only Invacare Mobile Recliners 28 Part No 1141494 SECTION 5 MAINTENANCE Replacing Casters Replacing Caster Assembly NOTE For this procedure refer to Detail A of FIGURE 5 9 1 Place the recliner on its side to gain access to the existing caster assemblies 2 Remove the hex screw and locknut that secures the caster assembly to the recliner frame 3 Align hole in caster insert with hole in recliner frame and install new caster assembly 4 Reinsert and tighten the hex head screw and nut 5 Return the recliner to its upright position NOTE Periodic inspection of the hex head screws and nuts is recommended to ensure that they are tight Time and usage may allow them to become loose and could cause breakage of the caster assemblies Replacing Caster Wheels NOTE For this procedure refer to Detail B of FIGURE 5 9 NOTE When replacing the rear locking caster wheel note the orientation of the locking actuator and axle bolt for proper reinstallation 1 Remove axle bolt and locknut that secure the existing caster wheel to the fork 2 Remove existing caster wheel from fork 3 Install the new caster wheel into the fork 4 Install the axle bolt and locknut and tighten securely NOTE On Models IH6074A and IH6065 series the rear casters are locking swivel cas
24. ill tip and bodily injury may occur DO NOT push or pull footrest to position the recliner DO NOT place hands or feet into any openings when adjusting the recliner Attendant or care provider should always verify placement of user s hands and feet prior to adjusting the recliner Failure to do so may result in serious bodily injury Invacare Mobile Recliners 10 Part No 1141494 SECTION GENERAL GUIDELINES Operation of recliner with missing or broken footrest or recline mechanism guards may result in bodily injury Periodic inspection of the footrest guard and recline mechanism guard MUST be made four times a year Torn cracked or otherwise damaged guards MUST be replaced prior to use Recliner MUST be removed from service until replacement guards are installed DO NOT lift the recliner by the footrest Lifting by means of the footrest may result in injury to the user and or damage to the recliner DO NOT attempt to stop the recliner with the wheel locks while in motion Wheel locks are not brakes Before attempting to transfer in or out of the recliner every precaution should be taken to reduce the gap distance Turn the recliner toward the object you are transferring onto When transferring to and from the recliner ALWAYS engage both wheel locks Special care MUST BE taken with people that have physical limitations which may require an assistant DO NOT traverse climb or go down ramps or slopes greater than 9 Invacare
25. ith warm water and mild detergent to remove superficial soil e Ground in dirt stains Use soft bristle brush and powdered cleanser or similar detergent Tar asphalt or creosote These will stain and should be removed as soon as possible Area can be cleaned with kerosene or naptha Chewing gum Scrape off carefully Remove remainder with kerosene or naptha e Paint or shoe polish Remove immediately Use a white cloth dampened with kerosene naptha or turpentine e Excrement Remove immediately Clean with 1 10 mix of bleach and water NOTE The wearability of your chair can be improved by using a quality paste wax periodically Part No 1141494 3l Invacare Mobile Recliners LIMITED WARRANTY PLEASE NOTE THE WARRANTY BELOW HAS BEEN DRAFTED TO COMPLY WITH FEDERAL LAW APPLICABLE TO PRODUCTS MANUFACTURED AFTER JULY 4 1975 This warranty is extended only to the original purchaser user of our products This warranty gives you specific legal rights and you may also have other legal rights which vary from state to state Invacare warrants the products manufactured to be free from defects in materials and workmanship for a period of three years and one year on the upholstery and Gas Spring Recline Cylinder from the date of purchase If within such warranty period any such product shall be proven to be defective such product shall be repaired or replaced at Invacare s option This warranty does not include any labor or shipping
26. lign the holes in the skirt to the holes in the chair back by fastening the hardware 11 Install the side panels Refer to Removing Installing the Side Panel on page 30 Part No 1141494 15 Invacare Mobile Recliners SECTION 3 ASSEMBLY 12 Repeat STEPS 14 16 for the other side panel DETAIL DETAIL REAR VIEW POSITIONING Retaining Ring Bracket Bolt C Clevis Pin Seat Frame DETAIL SIDE PANEL See Detail A Gas Spring a Bracket Panel Side View Push Buttons FIGURE 3 2 Assembling the Recliner Assembling Model IH6077A Invacare Mobile Recliners 16 Part No 1141494 SECTION 4 OPERATION SECTION 4 OPERATION A WARNING After ANY adjustments repair or service and BEFORE use make sure that all attaching hardware is tightened securely otherwise injury or damage may result CAUTION Ensure that there is adequate room to operate the Invacare Mobile Recliner There must be at least three feet clearance between the top of the recliner back and the surrounding objects otherwise damage to the recliner and or surrounding property may occur Reclining the Chair Models IH6074A and 1H6065 series User Recline NOTE For this procedure refer to FIGURE 4 1 NOTE The chair cannot recline if the recline lock bar is engaged An assistant must first swing recline lock bar up to the chair back and lock into position 1 While seated
27. ng bracket use care to pull straight out of V notch DO NOT remove by bending the cable Damage to the cable may occur 2 Remove cable assembly from V notch of the mounting bracket Detail B 3 Remove the mounting screw that secures the cable to the back frame 4 Remove the mounting screw which secures the release handle to the push handle Detail A 5 Secure new release handle to the push handle with the existing mounting screw Securely tighten Detail A Part No 1141494 27 Invacare Mobile Recliners SECTION 5 MAINTENANCE 6 Insert new cable assembly into V notch of the mounting bracket Detail B 7 Squeeze release lever up toward the mounting bracket and insert anchor end of new cable assembly into slot of release lever Detail B 8 Secure the cable assembly to the back frame with mounting screw Securely tighten DETAIL A HANDLE DETAIL CABLE ASSEMBLY Cable Mounting Screw Actuator Push Handle Mounting Bracket Release Handle Edif Release Lever Cable Assembly FIGURE 5 7 Replacing the Release Handle and Cable Assembly Model IH6077A Only Replacing Position Lock Lever Models H6074A and 1H6065 Series Only NOTE For this procedure refer to FIGURE 5 8 Removing Position Lock Lever Seat Frame 1 Remove two screws nylon washers and locknuts securing the position lock lever to the seat frame Installing Position Lock Lever 1 Secureth
28. ng from the clevis pin Remove mounting bolt and locknut securing the gas spring recline cylinder to the back frame Recline the back until cylinder can be removed from mounting bracket easily approximately a 45 angle Remove gas spring recline cylinder Loosen the locknut on the bottom of the cylinder Detail A Hold the bottom bracket and turn the cylinder until cable becomes taut NOTE If the cylinder was not locking when the lever was actuated turn cylinder clockwise If the cylinder was not locking when the lever was released turn cylinder counterclockwise Invacare Mobile Recliners 26 Part No 1141494 SECTION 5 MAINTENANCE 8 Turn cylinder 1 2 turn in the opposite direction of STEP 7 9 Reassemble by reversing STEPS 1 6 Cable DETAIL A ounting LOOSENING THE Screw fec LOCKNUT Recline Cylinder Back Frame Mounting Bolt Locknut Gas Spring Recline Cylinder DETAIL TIGHTENING THE Frame CABLE Clevis Pin Clevis Pin Bottom Bracket FIGURE 5 6 Adjusting Gas Spring Recline Cylinder Assembly Model IH6077A Only Replacing the Release Handle and Cable Assembly Model 1H6077A Only NOTE For this procedure refer to FIGURE 5 7 on page 28 1 With one hand squeeze release lever up toward mounting bracket and remove anchor end of cable assembly from slot in release lever Detail B CAUTION When removing the cable from the mounti
29. ructions and any additional instructional material such as Owner s Manuals Service Manuals or Instruction Sheets supplied with this product or optional equipment If you are unable to understand the Warnings Cautions or Instructions contact a healthcare professional dealer or technical personnel before attempting to use this equipment otherwise injury or damage may occur Service Information After the first six months of operation inspect all pivot points and fasteners for wear If the metal is worn the parts MUST be replaced Make this inspection every six months thereafter Regular maintenance of the mobile recliner and accessories is necessary to assure proper operation Operation Information Check all parts for shipping damage In case of damage DO NOT use Contact Carrier Dealer for further instructions ALWAYS keep hands and fingers clear of moving parts to avoid injury DO NOT use near an open flame or heat source as all upholstery materials even though treated with flame retardant can ignite when exposed to open flame Rear caster wheels MUST be locked during user transfer to or from recliner and while tilting and or reclining or inclining sitting up Ensure that casters are free of debris Casters and axle bolts require inspection every six months to check for tightness and wear DO NOT enter or exit the recliner when footrest is elevated DO NOT sit on the footrest when recliner is extended The recliner w
30. s to 15 inches in 2 inch increments To Set the Tray to a Locked Position 1 Pull down on the plunger release knob below the armrests of the chair seated and push pull the tray to the desired position 2 Ensure tray locks in place To Set the Tray to Freeflow 1 Pull down on the plunger release knob below the right arm rest of the chair seated and push pull the tray to the desired position 2 Slide the plastic keeper forward and release the plunder knob 3 Slide the tray in or out to desired position Plastic Keeper Plunger Knob FIGURE 4 10 Adjusting the Tray Position Invacare Mobile Recliners 22 Part No 1141494 SECTION 5 MAINTENANCE SECTION 5 MAINTENANCE A WARNING After ANY adjustments repair or service and BEFORE use make sure that all attaching hardware is tightened securely otherwise injury or damage may result Replacing the Back Cushion Model IH6074A and 1H6065 series NOTE For this procedure refer to FIGURE 5 1 Removing 1 Remove the four long hex screws that secure the back cushion to the back frame 2 Remove the four short hex screws that secure headrest bracket to the back cushion Repeat for remaining headrest bracket Installing 1 Align back cushion with the back frame 2 Install four long hex screws to secure the back cushion to the back frame Securely tighten 3 Secure the headrest bracket to the back cushion with four short hex scre
31. ters and the front casters are free wheeling and non pivotal On Model IH60774 the rear casters are locking swivel and the front casters are swivel only ALWAYS replace casters accordingly DETAIL A CASTER ASSEMBLY DETAIL CASTER WHEELS Recliner Frame Hex Head Screw Caster Locknut Insert Locking Acruator Caster Wheel Caster Wheel FIGURE 5 9 Replacing Casters Part No 1141494 29 Invacare Mobile Recliners SECTION 5 MAINTENANCE Replacing Plunger Release Knob NOTE For this procedure refer to FIGURE 5 10 1 Remove glide from end of frame 2 Remove retaining ring from end of plunger pin 3 Slide plunger release knob off the plunger pin 4 Lift plunger pin and spring out of the frame tube Plunger Pin F Frame 5 Insert new plunger pin and spring into Plastic the frame so that grooved end of pin Spring 1 Keeper extends below the frame tube Aid a 6 Place plunger release knob over the ur plunger pin O 7 Snap the retaining ring into groove of Plunger Release Knob Frame Tube the plunger pin etaining Ring at 8 Replace the glide into the end of the _ frame FIGURE 5 10 Replacing Plunger Release Knob Removing Installing the Side Panel NOTE For this procedure refer to FIGURE 5 11 Removing Side Panels 1 Press the push buttons near the bottom of the right side panel 2 Hold the push buttons in while pulling the panel outward 3 Repeat STEPS 1
32. ual are available on www invacare com Invacare Mobile Recliners 2 Part No 1141494 TABLE OF CONTENTS TABLE OF CONTENTS REGISTER YOUR PRODUCT 000000000000000000000000000000000000000000000000000000000000000 4 LABEL LOCATION 0000000000000000000000000000000000000000000000000000000000000000000000000000 7 Models IH6074A IH6065 series and IH6077A 7 SPECIAL NOTES 090900000000000000000000000000000000000000000000000000000000000000000000000000000 8 TYPICAL PRODUCT PARAMETERS 0000000000000000000000000000000000000000000000000000 9 SECTION CGENERAL GUIDELINES 0000000000000000000000000000000000000000000000000 10 Service InforrodtioFb 10 Operat omInforifia Obs ae ote ie 10 E Recline Option Operated by an Attendant eee teeteetentente te ntnntentun E SECTION 2 SAFETY INSPECTION 000000000000000000000000000000000000000000000000000 12 Safety Inspection Checklists 12 SECTION 3 ASSEMBLY 000000000000000000000000000000000000000000000000000000000000000000 14 Assembline the Reelihel neiii a A 14 Assembling Models IH6074A 1H6065 series seen 14 Assembling Model IH6077A eese eene 15
33. ws 4 Securely tighten Repeat for remaining headrest bracket Back Cushion Headrest Bracket Short Hex Screws Long Hex Screws Back Frame FIGURE 5 1 Replacing the Back Cushion Model IH6074A and 1H6065 series Part No 1141494 23 Invacare Mobile Recliners SECTION 5 MAINTENANCE Model IH6077A NOTE For this procedure refer to FIGURE 5 2 Removing 1 Remove the pan head mounting screw that secures the recline cable to the existing back cushion 2 Remove the four long hex head screws that secure the back cushion to the back frame 3 Remove the four short hex head screws from each of the two headrest brackets NOTE Reinstall the pan head mounting screw on the new back cushion assembly in approximately the same location as on the old back assembly Installing 1 Align new back cushion with seat and frame 2 Install four long hex screws to secure the back cushion to the back frame as shown in FIGURE 2 Securely tighten 3 Secure the headrest bracket to the back cushion with four short hex screws Securely tighten Back Cushion Push Handle Headrest Bracket Back Frame Long Hex VA Screws Pan Head D Mounting Screw Sy 8 Long Hex Screws Short Hex Screws FIGURE 5 2 Replacing the Back Cushion Model IH6077A Replacing the Footrest Cushion A WARNING DO NOT stand on the footrest or seat when entering or exiting the recliner The recliner will tip and bodily
Download Pdf Manuals
Related Search