MOBILE SERIES - sinclair air conditioners
Contents
1. When the unit is running in SLEEP mode press Hr key to set timer on the interval is 1 7 hours When the unit is running in SLEEP mode according to the time changes it could adjust the original set temp automatically to save energy and make a comfortable sleeping NOTE When using Fahrenheit remote controller the sign C or C will be corresponding changeed to or 14 1 After inserting the batteries press ON OFF key to start the unit 2 Press MODE key select AUTO mode according to the room temp the microcomputer will adjust the turn on or turn off of the compressor and fan motor automatically to offer comfortable effect 3 Press SEND key to transmit the operation to the unit AUTO MODE According to the room temp the microcomputer will adjust the turn on or turn off of the compressor automatically to offer comfortable effect NOTE When using Fahrenheit remote controller the sign C C or C will be corresponding changed to F F or 15 1 When the unit is running press TIMER key to set the TIMER operation 2 Press Hr Min key to set the TIMER ON it can be selected in the range of 1 18 hours 3 Press SEND key to transmit the operation to the unit 4 Press SLEEP key then press the Hr Min key to set the TIMER OFF it could be selected in the range of 1 7 hours After the SET TI2. Window kit Window Es Rear ClipB Plastic Pipe End Hole 132mm Window Or wall 18 If the exhaust duct requires bend please refer to the following installation dimensions CAUTION The wrong mounting diagram if the exhaust duct is bent too great it could cause malfunction easily The mobile There are castors at the bottom conditioner of the unit according to the demand it can be moved in the room very conveniently Air inlet grille WARNING Ts Before maintenance please pull out the power plug and cut off power supplyto avoid electric shock Clean the air filter If the usage environment of the unit has lots of dust the cleaning of Recommended once air filter should be more frequently every three weeks Disassembly and Cleaning Press two hooks of the grille take off the cover of air inlet grille then take out the air filter Wash the filter solely to spray like the spray in bath and to shake the filter or to immerse filter into the gentle soap water then dry it in shade WARNING NOTE Never use water above 45 to wash the filters or it could cause deformation or discoloration 20 Clean the air Please use a cloth that slightly moistened with water whose temperature is conditioner below 40 the soap water or the water with cleans
3. USER S MANUAL SINCLAIR AIR CONDITIONING Summary Nias sete es cies eh th anata ce Weekes REA D MEAE MEE E eese ee 1 Working principle 1 Models amp specifications Cerea a Cor 2 SEFUGEUFG geiter idara eue sh et hs 3 Operating 5 4 8 3X Names and Functions of the Remote Controller 9 10 COOL mode Operation es e due quw V Og aute me owe a O 11 DRY 13 SLEEP mode operation 14 AUTO mode operation 15 TIMER mode ca MAK Be SS CARS rd 16 3X Installation guide for castor drainage pipe and air exhaust accessory 17 19 Care and Maintenance oem bhy aaun ot e a e es 20 21 Trouble Shooting a 22 User NOTICES sse fees Oe ae eRe Gre E 23 After Servi CES Yep VO ea f gi So P Gute det ae E Oh On e 24 Circuit diagram 25 This MOBILE AIR CONDITIONER is a small moveable air conditioner It possessed the functions of COOL HEAT DRY and the Separate Ventilation and depends on different places it can be moved as will It is fit for home and office use especially fit for the house with many rooms With the compact configuration excellent workmanship elegant appea
4. due to the thunder please pull out the power plug and reinsert it then press the SEND key NOTE When using Fahrenheit remote controller the sign C C or C will be corresponding changed to F F or F 1 0 MODE key Press the MODE key step by step the LCD will display the COOL FAN HEAT AUTO mode circularly TEMP key PressWonce the SET TEMP will decrease 1 C Press gonce the SET TEMP will increase 1 C The SET TEMP canbe selected from 16 C 30 C 61 F 86 F FAN key The switchover of FAN mode are HIGH MD LOW TIMER key Press the key to select the SET TIMER mode or the TIME mode Whenselect the SET TIMER mode the LCD willdisplay the time ofthe SET TIMER mode while select the TIME mode the LCD will display the current time Hr Min key When the unit is running inthe TIME mode press once the number willincrease 1 press Min once the number will increase 1 When the unit is running inthe SET TIMER mode press the key once between0 7 the number of time willincrease0 5 press the key once above 8 the number of time will increase 1 When the unit is running in SLEEP mode press the Hr key once the time interval will increase hour and will circulate from 1 to 7 hour s 1 Afterinserting the batteries press ON OFF key to start the unit 2 Press MODE key to choose COOL mode 3 Press FAN key to set fan speed 4 Press TEMP
5. key to set the desired temp 5 Press SEND key send the operation totheunit When temperature ofroomsensoris higher than the set temp compressor runs the unit starts cooling operation Whentemperature sensor is lower than the set temp compressor stops the unit runs in FAN mode Thesettemp shouldbe inrange of 16 C 30 C 61 F 86 F NOTE When using Fahrenheit remote controller the sign C or C will be corresponding changed to F F or F 11 1 After inserting the batteries press ON OFF key to start the unit 2 Press DRY key to set DRY mode when repress the key it will run in original operation 3 Press TEMP key to set desired temp 4 Press FAN key to set fan speed 5 Press SEND key to transmit the operation tothe unit DRY When the unit is in DRY mode the compressor is protected the fan motor runs at low fan speed NOTE When using Fahrenheit remote controller the sign C or C will be corresponding changed to F F or F 13 After inserting the batteries press ON OFF key to start the unit Press MODE key to select the operation mode Press TEMP key to set desired temp Press FAN key to set fan speed Press SEND key to transmit the operation to the unit Press SLEEP key to set SLEEP operation when press once more it will stop
6. or brass wire to replace fuse the capability of fuse must be appropriate In order to avoid damage to power cord and electrical leakage do not fix the power supply on the knife edge or sharp object The wiring must be operated by the professional and according to the national regulations In fixed circuit there must be electricity leakage protection switch of enough power capacity and 16A thermal magnetic breaker air switch with enough space the earth wire can t be connected to water pipe or gas pipe When the air conditioner is not used please pull out the power plug or cut off power supply There must be reliable ground wire in the power supply Earthing Gas pipe LCD instruction dynamic display TIMER display COOL mode DRY mode se Zi DISPLAY TEMPmod AUTOmaode NOTE When using Fahrenheit SET TIMERON OFF controller the sign of temperature FAN display changes C to Names and Functions Remote Controller Remote Control window FAN SPEED SET SLEEP ON OFF LCDscreen MODE SET TIMER MODE FAN SLEEP TEMP TIME Control panel and the function 1 ON OFF key Press once to start and press once more to stop the unit 2 MODE key Press this button to change operation mode in order of FAN COOL DRY AUTO FAN 3 FAN SPEED key When the unit is running in FAN COOL and HEAT mode there are 3 kinds of fan speeds to be selected pr
7. MER ON the unit turns off at once when the set time arrived the unit will run in original mode Press TIMER key to select TIME the screen will display the current time press Hr Min key to adjust the number of current hour or minute When pressing the SLEEP key to set the SLEEP mode the SET TIMER mode will be canceled when selecting the SET TIMER mode the SET SLEEP mode will be canceled NOTE When using Fahrenheit remote controller the sign C or C will be corresponding changed to F F or F 16 THE AIR EXHAUST 1 Install the adjutable window silder kit or drill a hole at the DUCT MOUNTING nearest window METHOD 2 Fix the square end of the exhaust duct to the exhaust terminal of the unit as depicted in Fig 4 3 Put the other end discharge to the window as depicted in Fig 5 or Fig 6 Attention The length of the air exhaust must be between 500mm 2000mm Front Plastic Pipe End Middle Plastic Pipe End Rear Clip B UIT Witt Plastic Pipe End Fig 4 17 CAUTION 1 In order to correctly installing the air exhaust duct please contact your local dealer for the service 2 When mounting try to keep the square end of the exhaust duct horizonal 3 Don t add or connect other pipes to it otherwise it will cause mechanical malfunction
8. er after wiping the dirt Do not use gasoline diesel oil or the congeneric substance to clean the unit Before cleaning please pull out the power plug Us Be 21 If malfunction occur please check the following before maintenance The air conditioner doesn t start The power supply is not connected well 1 Insert the power plug tightly The power plug is not inserted tightly 2 Replace the power plug or socket There is the malfunction of power plug 3 Ask for the maintenance man to or socket replace the fuse The fuse is broken The LCD displays the number of Is the TIMER ON in operation Cancel the SET TIMER operation time but it doesn t work or to wait the auto running Although it was set to COOL 1 The room temp is lower than 1 This is the normal phenomenon mode there is no cool wind the set temp 2 Unit is running in defrosting operation 2 The evaporator frosts it will resume running in original operation after defrosting Although it was set the DRY 1 The evaporator frosts 1 Unit is running in defrosting operation mode there is no cool wind it will resume running in original operation after defrosting The LCD displays E1 1 Power supply is unstable Cut off power supply after 10 2 Malfunction occurs minutes turn on the unit if E1 still be displays please inform the maintenance man to maintain The LCD displays H8 The water tank gets full 1 Pour out water in the tank p
9. ess FAN SPEED key to choose between LOW HIGH 4 SET TEMP key When turn on the air conditioner in the COOL HEAT mode the control panel will display the set temp Press A V to increment or to decrement the set temperature 5 SET TIMER key Press A Y key to set the time for timer on or timer off When the unit is running you could set the timer off the unit will stop running When the unit is stop running not power off set timer on and the time interval that being set will be 0 5 24 hour s press V key to adjust 6 SET SLEEP key When the unitis running press once to set SLEEP operation repress it the unit will stop the SLEEP operation There is no SLEEP operation in AUTO mode COOL mode 1 Selectaplacethatnear doorand window install the exhaust duct the installation method please refer to P19 put the exhaust duct out of the door do not close the door and window tightly leave enough space for air flow for example open the window or door to keep a good ventilation 2 Press MODE key to select COOL mode 3 Press TEMP key to set the suitable temp 16 C 30 C 61 F 86 F 4 Press FAN key toselectthe suitable fan speed HIGH MD LOW CAUTION When the unit is running in COOL mode in order to keep a good cooling effect please pay more attention to 1 If there is the direct sunlight at the window please use the curtain to shield 2 Do not use other hea
10. f the appliance is placed in a position admitting to drain water you also can connect the drain hose to the drain port to drain water As figurre shown below Fig 2 Fig 3 Rubber Plug Fig 2 Fig 3 8 LCDscreen Itshows all set contents SEND key Press this key to transmit the operation the screen will show the operation SLEEP key Press this key toset SLEEP operation and press the Hr key to adjust the time oftimer off itcan be choose from 1 7 hours whenrepressthiskey the operation will stop DRY key Press this key the air conditioner will run in DRYmode ON OFF key Press once to start and press once more to stop the unit Makesuretoaimthe signal portofremote controller at the signal receiver indicator of front panel Only the AUTO ON OFF SLEEP SEND keys could be used to send the current display operation the otherkeys could be used to change the mode The other functions please refer to the cooling only type air conditioner NOTE When using Fahrenheit remote controller the sign C C or C will be corresponding changed to F F or NAMESANDFUNCTIONSOFTHEREMOTE CONTROLLER POWER OFF Incase of the power off during the operation all options will be ceased Ifneed to resume the operation please repress the SEND key If there is malfunction in the operation procedure or wrong operation
11. lease see the fig in P8 2 If the malfunction still exists please inform the maintenance man to maintain 22 Location Others Do not install the unit in the hermetic place and keep well ventilation to avoid malfunction occurs Do not install the unit at where it will be exposed to direct sunlight in order to avoid fading and efficiency reducing Do not install the unit in the moist place it can cause electrical leakage Please do not install the unit to the following places The places with gas fire oil or where it will cause malfunction Please pay attention to the people of following 1 Young children patient 2 The people who are hard to express themselves 3 The people who is very tired drunk or the one who had taken soporifics Do not step on or put anything on the top of the unit it will slop and can cause malfunction Do not apply the cold wind to the body for a long time it can cause health problems The unit should be placed about lm or more away from TV or it will be effected by the electromagnetic wave The air inlet outlet can t be blocked by obstruction or it will cause malfunction Do not insert hands or stick into the air inlet or outlet especially pay more attention to young children or it can cause the accident easily 23 Do not incline or overturn If the abnormal phenomenon occurred please pull out the power plug at once and inform the dealer t
12. o check and maintain Do not use the insecticide or other sprays it can cause deformation or crack If any quality problems or any other problems exist please contact with the local dealer 24 SA Q TRANSFORMER BN 1 1 moo 22 w OUR a MP v 7 BLW BK a BL pu N 0 2 V XT ome Gy WATER MOTOR sn CNT t TR IN TR QUT BL lt RLY7 ROOM RD CONP ROOM SENSOR CN3 aT CN2 n 9 NS E 16 TUBE CNI PIPE TEM SENSOR amr Y AP2 BK DOWN FAN MOTOR RD E 63616042 2 AMC 09C The circuit diagrams of all above are for reference they are subject to be changed without notice 25
13. rance it looks like a standing Benz car It is convenient for moving energy saving and with low noise Note Please read this manual carefully before operating the unit the manual is used for reference and the technical parameters are subject to change without notice With the help of upper motor the airflow of indoor pass through the evaporator becomes the cooled wind but with the help of lower motor the airflow of indoor pass through the condenser becomes the heated wind There is two duct systems designed in its structure The heated wind is discharged by the rear outlet the cooled wind is discharged by the front outlet flow guided by the louver and it brings the gentle cooling airflow and the low temperature environment is maintained The Working Principle Cooled wind t Evaporator Upper motor lt gt Airflow 1 Lower moror Capillary gt Heated wind Airflow 2 Condenser Model AMC 09C Cooling Capacity W 2600W Power Source 220 240V 50Hz Rated Input Current A 5 3 Rated Power Input W 1200 Flow Volume m h 430 Sound Press Level dB A 55 Refrigerant R407C Net Weight Kg 31 Dimension Body H X W x DO Cnm 840X 450 X 370 Dimension Package H X WXDO mm 880 X 685 X 425 Note 1 The noise was tested when the unit is running in cooling wind mode 1 meter away from the front outlet dehumidifying capacity 2 The technical parameter
14. s are subject to be changed without notice Please refer to those listed on nameplate of the unit 3 Device is not intended for continuous running Q m working range of COOL mode and DRY mode Location conditions Power supply The working range of COOL mode is 16 C 35 C the working range of DRY mode is 16 C 35 C When operating the unit should be placed on the horizontal place and more than 50cm away from the wall or other obstructions m TA Before the unit is power on please check the following The power supply voltage 6 The lead wire is suitable for the start up current of more than 20A to avoid the voltage decline when the unit starts suddenly The power plugs and the sockets can be supported by the current that is more than 16A The thread section of the lead wires and any continued use lead wire is no less than 2 5mm If the power supply cord is damaged replace it by the special power supply cord If the power supply is needed to replace or maintain please contact with the dealer and ask for the professional personnel to do the repairing work The air conditioner must be safety earthed Earth wire must be connected to the special device of the building That is for providing good earthing for the air conditioner Water pipe Can not use steel wire
15. t sources in the air conditioning room DRY mode Please close the door and window to obtain a better dehumidifying effect Press MODE key select DRY mode the unit willruninthe DRY mode atthe same time the upper motor is running at the low speed it is not adjustable CAUTION When the air conditioner is used as dehumidifier it is no need to install the exhaust duct FAN mode 1 Press MODE key to select FAN mode 2 Press FAN SPEED key to choose from the HIGH MD LOW fan speed options AUTO mode Press MODE key to select AUTO mode the microcomputer process will automatically choose COOL DRY HEAT mode for ensuring the indoor constant temperature efficiency HEAT mode Press MODE keyto choose HEAT mode at the same time compressor and lower motor stop running only PTC is running the upper motor is running at the set fan speed WATER When in cooling or dehumidifying mode the dew water will be drained into the tank DRAINAGE When the tank gets full the indicator will flash and the buzzer will sound eight times LCD window shows errorcode H8 atthe same time the unit stops running METHOD OF Cut off power supply move the appliance to a suitable place to pull out the plug and DRAINAGE pour out the water in tank When water is drained out completely re insert the plug back into the drainage pipe to avoid dew water leakage As figurre shown below Fig 1 When restarting the appliance it must be set again I
Download Pdf Manuals
Related Search