Starter Kit - LED Indoor/Outdoor Lighting Strips
Contents
1. a IMPORTANT There is only one way to connect the Power Supply Connector to the Power Supply Make certain the icons match before connecting Step 6 Mount 6 1 Mount Channeling Strategically mount your 6 x 4 channeling strips using the 3M 2 way tape provided To obtain optimum adhesion the bonding surfaces must be clean dry and well unified 6 2 Install LED Strip Install LED strip by pressing it firmly into each channeling strip Working from Power Supply Connector to End Cap make certain strip lies flat 6 3 Mount Power Supply Position Power Supply near power outlet and secure to your desired surface For outdoor applications position Power Supply 1 foot above the ground IMPORTANT Do not plug into outlet until Power Supply is secured Power Supply should only be plugged into a weatherproof covered Class A GFCI receptacle Do not install or use within 10 feet of a pool Do not use in a bathroom 6 4 Mount Dimmer Position dimmer near power outlet and secure to your desired surface The Inline on off Dimmer Switch fits between the Power Supply Connector and Power Supply Unplug the Power Supply from the AC outlet before connecting Match the icons on the Power Supply Connector with the icons on the Inline Dimmer IMPORTANT Do not plug into outlet until dimmer is secured le2. CORRECT INCORRECT Step 7 Connect to Power Connect the other end of the Inline Dimmer to the Power Supply and plug the Power Supply into the wall outlet NOTE The Inline Dimmer is optional and not required for a complete install If the Inline Dimmer is not included in your installation connect the other end of the Power Supply Connector to the Power Supply and plug the Power Supply into the wall outlet f je 2 N Ana CORRECT INCORREC gt a IMPORTANT There is only one way to connect the Power Supply Connector to the Power Supply Make certain the icons match before connecting TROUBLESHOOTING Most of the problems you may encounter will be caused by improper assembly If you have any questions or need additional parts please contact our customer service or visit us at CabLEDLighting com Go Through the Solutions None of the LED Make sure Power Supply is plugged in and the AC power outlet is getting power strip is lit P Check connection from Power Supply Connector to Power Supply Check the connection on the Power Supply Connector to the LED strip Pull the strip If it comes out of the connector you will need a new connector Go Through the Solutions Only part of the LED Check all connectors attached to the part of the strip that is not lit Pull the s
3. connectors 19 OPTILED Technology LLC Raritan Center Business Park 30 Campus Drive Bldg CP 2 Edison 08837 1 855 533 6268 customerservicehd optiled com CabLEDLighting com
4. 1 x Power Supply Connector Connects 2 CabLED strips Used in all installations with a 61cm 24inch flexible cable Connects CabLED strips to power supply 2 x End Caps 1 x Dimmable on off Switch 1 x 18W Indoor Outdoor Power Supply Used in all installations Protects end of CabLED strip that is not 9 DJ connected to a connector 6 x 4 Channeling Strips 1 x Cutting Jig 1x6 of 3M 2 Way Adhesive Tape 2 Required Tools A Zu lt r Pencil Pliers Scissors ser 5 Safety Glasses Tape Measure Level CabLED Strip Specification The CabLED strip uses CREE High Brightness LED lights set every inch and can be cut every 7 inches 18cm Warm White 3500K Input Voltage 24V Input Current 154mA Power 3 7W m Weight 3 50z m Lifetime 35 000h Beam Angle 120 Lumen Meter 170lm CRI 80 No of LED Segment 6pcs LED Pitch 30mm IP Rating IP65 Operating Temperature 20 50 Storage Temperature 25 60 Min Bending Radius 3 9in Max Connection Length 15ft with an 18W Power Supply Max Connection Length 25 with a 30W Power Supply Max Connection Length soft With 70 lumen maintenance with a 60W Power Supply 30 amp 60 watt power supplies can be purchased at homedepot com 3 or through CabLEDLighting com IMPORTANT WARNINGS AND CAUTIONS CAUTION Create layout plan before installation Locate power supply determine suitable mounting method
5. Starter Kit User s Manual CONTENTS Unpackza 2 2 Required an 3 StrIP SPECHCatlon lt 3 Warnings and 4 5 Plan Your 6 Measure and Mark Surface nsnenneneeseenseeensnnnnssennnnennsnnnnnsnnnnnnunnnnenr 6 7 Mark aiid CUELED SUIp ee 8 9 Installation ses ee 10 14 Connect tO POWER eiia 17 Troubleshooting sesssessessesseessessessssssessessessscsscsacsseesscsaceaessseseceseeseessesaeeaes 17 18 BEFORE YOU BEGIN MAKE SURE YOU CAREFULLY READ AND UNDERSTAND THE INSTRUCTIONS IN THIS MANUAL This CabLED kit includes an assortment of components to cover a variety of indoor or outdoor applications Our goal is to make this installation easy for you Please follow the instructions in the order presented in this manual and be sure to observe all warnings and cautions IMPORTANT Each connector consists of two parts a top and bottom which are partially assembled at the factory Do not push the connectors together BEFORE installation Do not cut the LED strip before planning your installation Make certain the following components are included in the package If any of the parts are missing or damaged please contact OptiLED Customer Service Parts are not shown in actual size Package Contains S 1x6 LED Indoor Outdoor Lighting Strip 2x24 Jumper Cables
6. l the LED strip to make sure you have installed it properly CORRECT INCORRECT INCORRECT INCORRECT a 11 Turn the cable over and make sure the LED strip is pushed completely to the back ofthe cable 4 2 Install Inline Dimmer Optional If included in your installation the Inline on off Dimmer Switch will fit between the Power Supply Connector and the Power Supply Unplug the Power Supply from the AC outlet before connecting Match the icons on the Power Supply Connector with the icons on the Inline Dimmer NOTE The Inline Dimmer is optional and not required for a complete install Using pliers apply even pressure to the bottom and top halves of the connector to push connector together securing LED strip inside After compressing the center of the connector check to make sure the left and right side of the connector have clicked into place and are secure E gt Y lf Ball 4 3 Install Jumper Cable IMPORTANT When using pliers that do not cover the surface of the connector apply pressure to one side of the connector to push the connector together Without moving the strip or the With the LED side of each strip facing up insert one strip into one side of the Jumper Cable 5 Pap connector carefully rotate the pliers to apply pressure to the other side of the connector and push
7. o ensure a straight and even cut TIP You can use the jig included in kit to ensure a straight and even cut o Rotate the strip along the surface you marked locate nearest cut line and mark Rotate and mark again for three sided area Adjust your layout if necessary EI Step 4 Install Connectors 4 1 Install Power Supply Connector Find the end of the LED strip that will be installed nearest to the power With LED side facing up slide the strip into the opening in bottom half of the Power Supply Connector until it reaches the end TIP To make this installation process easier apply petroleum jelly to the end of the CabLED lightly coated to make it easier to insert This will not hurt the product Using pliers apply even pressure to the bottom and top halves of the connector to push connector together securing LED strip inside After compressing the center of the connector check to make sure the left and right side of the connector have clicked into place and are secure a IMPORTANT When using pliers that do not cover the surface of the connector apply pressure to one side of the connector to push the connector together Without moving the strip or the connector carefully rotate the pliers to apply pressure to the other side of the connector Make sure both sides of the bottom half of the connector snap into the top half Gently pul
8. s and connectors measure and calculate the length of CabLED LED required LED strip can only be cut at every 7 inches 18cm and must be cut exactly on the indicated mark a WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions a CAUTION A CAUTION alerts you to the possibility of damage to or destruction of the equipment if you do not follow the corresponding instructions Use only CabLED connectors channeling inline dimmer and power supply WARNING Do not open dismantle or attempt to repair the LED strip bottom half of the connectors inline Do not use acid or alkaline liquid to clean dimmer or power supply There are no user serviceable parts Products should be installed in accordance with the owner s manual current electrical codes and or the current National Electric Suitable for indoor and outdoor use Code NEC Improper installation may present a possible shock or fire hazard Always make sure f the LED strip is disconnected from the power source before cutting connecting mounting or Risk of electric shock Do not use with extension cord near water or where water may modifying in any way accumulate For use only on GFCI proctected circuits The LED strip is water resistant not water proof Do not submerge Mount power supply at Material may become brittle when cold Do not install where it may be stepped on or least one foot above the ground Do not s
9. to consider when measuring for your installation Determine where your Power Supply will be mounted and plan your installation so the Power Supply Connector will be near the wall outlet 2 2 For Use in a Corner Area Measure and mark the surface where the LED strip will be installed The connectors add about 1 2 inch 1 27cm of length to the end of the LED strip and Use the Power Supply Power Supply Connector 24 Jumper Cable and End Cap for installation the LED strip may ONLY be cut along the cut line marked at every 7 inches 17 78cm on the top of the strip It may be useful to lay out the strip and connectors to visualize how the components fit together in your space before you begin DO NOT PUSH CONNECTORS TOGETHER I X IMPORTANT Place Power Supply Measure and mark the surface where the LED strip will be installed near outlet and off the ground IMPORTANT The LED strip may ONLY be cut every 7 inches 17 78cm indicated by a cut line on the LED side of the strip When you are measuring for your installation if the total length is not a multiple of 7 then adjust the plan of your layout to be cut on the nearest mark Step 3 Mark and Cut LED Strip 3 1 Mark LED Strip 3 2 Cut LED Strip Hold the LED strip up to the surface you just marked locate nearest cut line and mark Use a pair of sharp scissors to cut the LED strip EXACTLY on the cut lines you have marked TIP You can use the jig included in kit t
10. to the end Insert the other strip into the other side and push it to the end TIP To make this installation process easier apply petroleum jelly to the end of the CabLED lightly coated to make it easier to insert This will not hurt the product Make sure both sides of the bottom half of the connector snap into the top half Gently pull the LED strip to make sure you have installed it properly CORRECT INCORRECT INCORRECT INCORRECT 12 13 4 4 Install End Cap Slide End Cap onto LED strip that will have no connector The End protects the strip End Cap does not have to be compressed TIP To make this installation process easier apply petroleum jelly to the end of the CabLED lightly coated to make it easier to insert This will not hurt the product a Step 5 Test The 18W Power Supply included in this kit will support up to 15 of product 30W and 60W Power Supplies can be purchased at HomeDepot com or through CabLEDLighting com Connect the other end of the Inline Dimmer to the Power Supply and plug the Power Supply into the wall outlet to test your assembly If it works properly unplug and continue If not see the Troubleshooting section NOTE The Inline Dimmer is optional and not required for a complete install If the Inline Dimmer is not included in your installa tion connect the other end of the Power Supply Connector to the Power Supply and test your assembly v of CORRECT INCORRECT
11. trip is lit LED strip If it comes out of the connector you will need a new connector LED strip is flashing Make sure you are using the Power Supply shipped with the Starter Kit If you ON and OFF bought another kit or additional LED strip check the Power Supply specifications to make sure it supports the additional length LED strip not cut Depending on how you cut the strip you may still be able to save that section exactly on cut line The cutting tolerance is about 3 mm 1 8 inch on either side of the cut line Cutting in a straight line is crucial and the two wires inside the strip must be pushed to the very end inside the connector to make contact with the pins Go to the cut line before the cut line you incorrectly cut and make the section shorter You may be able to adjust your layout by moving the sections around Visit HomeDepot com or CabLEDLighting com to purchase additional LED strips or Straight Connectors Connectors pushed e If you pushed the connector top into the bottom before installation or if the LED together before strip was not pushed completely to the end of the connector and did not secure installation the strip you may be able to save the part Use a flat screw driver to gently widen the sides of the top connector and push the bottom connector apart NOTE This may not fix the connector and you may need to use a new connector Visit HomeDepot com or CabLEDLighting com to purchase additional
12. ubmerge in water subject to physical damage Safety measures must be observed at all times during the installation of this product Do not install near flammable liquids Use proper safety gear and tools during the installation process to prevent physical injury Do not look directly at the LED lights in the CabLED strip when lit Do not mount or support flexible light in a manner that can damage the outer jacket or cord insulation Risk of fire and electric shock Uncoil flexible light prior to plugging in Step 1 Plan Your Installation 2 1 For Use in a Straight Area Measure and mark the surface where the LED strip will be installed IMPORTANT The connectors consist of two parts a top and bottom which are partially Use the Power Supply Power Supply Connector 24 Jumper Cable and End Cap for installation IMPORTANT Place Power Supply near outlet and off the ground assembled at the factory Do not push the connectors together or cut the LED strip BEFORE you have planned your installation We have included an assortment of components to cover a variety of indoor or outdoor applications Plan your installation carefully to decide exactly which components your installation requires All installations require the Power Supply Connector which connects the LED strip to the Power Supply and the End Cap which is used to protect the other end of the LED strip Step 2 Measure and Mark Surface There are a few things
Download Pdf Manuals
Related Search