QUAD SCAN PRO
Contents
1. DJ VY QUAD SCAN PRO a 9 ITS User Instructions Rev 3 14 2013 ADJ Products LLC all rights reserved Information specifications diagrams images and instructions herein are subject to change without notice ADJ Products LLC logo and identifying product names and numbers herein are trademarks of ADJ Products LLC Copyright protection claimed includes all forms and matters of copyrightable materials and information now allowed by statutory or judicial law or hereinafter granted Product names used in this document may be trademarks or registered trademarks of their respective companies and are hereby acknowledged All non ADJ Products LLC brands and product names are trademarks or registered trademarks of their respective companies ADJ Products LLC and all affiliated companies hereby dis claim any and all liabilities for property equipment building and electrical damages injuries to any persons and direct or indirect economic loss associated with the use or reliance of any information contained within this document and or as a result of the improper unsafe unsufficient and negligent as sembly installation rigging and operation of this product Europe Energy Saving Notice Energy Saving Matters EuP 2009 125 EC Saving electric energy is a key to help protecting the enviroment Please turn off all electrical products when they are not in use To avoid power consumption in idle mode disconnect all e2. 4 Remove and replace the gobo with your desired replacement Reinsert the retainer ring and make sure the ring rests firmly against the gobo 5 Slide the gobo houseing back into place and secure the housing by tighting the thumb screw e TTF Yo ESTY TLI ad Ko Power Cord Daisy Chain With this feature you can connect the fixtures to one another using the IEC input and output sockets The quantity that can be connected is 4 fixtures maximum After 4 fixtures you will need to use a new power outlet They must be the same fixtures DO NOT mix fixtures ADJ Products LLC www adj com Quad Scan Pro Instruction Manual Page 22 e TTE Co Sor TaM tae Fuse Replacement Disconnect the unit from its power source Remove the power cord from the unit Once the cord has been removed you will find that the fuse holder is located inside the power socket Insert a flat head screw driver into the power socket and gently pry out the fuse holder Remove the bad fuse and replace with a new one The fuse holder also has a holder for a spare fuse e TTET EIT LL ad ae Cleaning Fixture Cleaning Due to fog residue smoke and dust cleaning the internal and external optical lenses and mirror should be carried out periodically to optimize light output Cleaning frequency depends on the environment in which the fixture operates l e smoke fog residue dust dew In heavy club use we recommend cleaning on a monthly basis Periodic cleaning will e
3. 7 Amp Duty Cycle None DMX 1 5 amp 32 DMX Channel Modes Sound Active Yes Working Position Any Safe Secure Position Warranty 2 Year 730 days Auto Sensing Voltage This fixture contains a automatic volt age switch which will auto sense the voltage when it is plugged into the power source Please Note Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice ADJ Products LLC www adj com Quad Scan Pro Instruction Manual Page 26 ADJ Products LLC 6122 S Eastern Ave Los Angeles CA 90040 USA Tel 323 582 2650 Fax 323 725 6100 Web www adj com E mail info americandj com A D J Supply Europe B V Junostraat 2 6468 EW Kerkrade Netherlands E PEE AEE service adjgroup eu www adj eu youtube com adjlighting Tel 31 45 546 85 00 Fax 31 45 546 85 99 Follow Us On HOM facebook com americandj
4. cable for data input and data output Figure 1 We recommend Accu Cable DMX cables If you are making your own cables be sure to use standard 110 120 Ohm shielded cable This cable may be purchased at almost all professional sound and lighting stores Your cables should be made with a male and female XLR connector on either end of Figure 1 ADJ Products LLC www adj com Quad Scan Pro Instruction Manual Page 6 e TTET EIT LLI ad Ko Set Up the cable Also remember that DMX cable must be daisy chained and cannot be split Notice Be sure to follow figures two and three when making your own cables Do not use the ground lug on the XLR connector Do not con nect the cable s shield conductor to the ground lug or allow the shield conductor to come in contact with the XLR s outer casing Grounding the shield could cause a short circuit and erratic behavior COMMON DMX512 OUT DMX512 IN 3 PIN XLR DMX 3 PIN XLR Figure 2 XLR Male Socket XLR Female Socket 1 oe 2 yn Figure 3 XLR Pin Configuration Pin 1 Ground Pin 2 Data Compliment negative cea aa loan aati See eee ee eel Pin 3 Data True positive Special Note Line Termination When longer runs of cable are used you may need to use a terminator on the last unit to avoid erratic behavior A terminator is a 110 120 ohm 1 4 watt resistor which is con nected between pins 2 and 3 of a male XLR connector DATA and DATA Th
5. Service Hours are Monday through Friday 8 00 a m to 4 30 p m Pacific Standard Time Voice 800 322 6337 Fax 823 582 2941 E mail support americandj com Warning To prevent or reduce the risk of electrical shock or fire do not expose this unit to rain or moisture Warning This may cause severe eye damage Avoid looking directly into the light source at all times ADJ Products LLC www adj com Quad Scan Pro Instruction Manual Page 2 e TTE Vo Ee La od xe General Instructions To optimize the performance of this product please read these operating instructions carefully to familiarize yourself with the basic operations of this unit These instructions contain important safety information regarding the use and maintenance of this unit Please keep this manual with the unit for future reference Quad Scan Pro Features DMX 512 Protocol Compatible 1 5 or 32 DMX Channels e X Y Mirror Control 3 Operating Modes Sound Active Show Mode and DMX Control Internal Microphone Digital Display for Address and Function Setting UC3 Controller Not Included Power Cord Daisy Chaining See page 22 Quad Scan Pro Warranty Registration The Quad Scan Pro carries a 2 year 730 days limited warranty Please fill out the enclosed warranty card to validate your purchase and warranty You may also register your product online at www americandj com All returned service items whether under warranty or not must be freight pre p
6. TER to confirm 4 The slave units will now follow the Master unit NOTE In a Master Slave configuration you can set one fixture to Master or Slave 1 SL 1 and then set the next fixture to Slave 2 SL 2 in doing this the fixtures will now have contrast movement to each other ADJ Products LLC www adj com Quad Scan Pro Instruction Manual Page 15 Quad Scan Pro 1 Channel Mode DMX Traits Quad Scan Pro UC3 Control Blackout Blackout the unit Function SHOWS BLACKOUT SHOW 1 SHOW 2 SHOW 3 SHOW 4 SHOW 5 SHOW 6 SHOW 7 SHOW 8 SHOW 9 SHOW 10 SHOW 11 SHOW 12 SHOW 13 SHOW 14 SHOW 15 SHOW 16 SOUND ACTIVE SHOWS 1 16 Function 1 White LED Strobe 2 White LED Strobe by sound 3 Multicolor Strobe by sound Select Show Show 1 16 Mode ADJ Products LLC www adj com Quad Scan Pro Instruction Manual Page 16 Sound Strobe LED ON Show LED Blinking e TTE Vo IoT La od xe 5 Channel Mode DMX Traits 1 Function PAN TILT MOVEMENTS NO MOVEMENT MOVEMENT 1 MOVEMENT 2 MOVEMENT 3 MOVEMENT 4 MOVEMENT 5 MOVEMENT 6 MOVEMENT 7 MOVEMENT 8 MOVEMENT 9 MOVEMENT 10 MOVEMENT 11 MOVEMENT 12 MOVEMENT 13 MOVEMENT 14 MOVEMENT 15 MOVEMENT 16 SOUND ACTIVE PAN TILT SPEED MOVEMENT SLOW FAST MASTER DIMMER 0 100 STROBING OPEN STROBING SLOW FAST OPEN SLOW OPEN FAST CLOSE OPEN FAST OPEN SLOW CLOSE OPEN SOUND ACTIVE STROBING OPEN ADJ Products LLC www a
7. aid and accompany a return authorization R A number If the unit is under warranty you must provide a copy of your proof of purchase invoice Please contact ADJ customer sup port for a R A number e TTE To ESTY TL dae Handling Precautions Caution There are no user serviceable parts inside this unit Do not attempt any repairs yourself doing so will void your manufactures warranty In the unlikely event your unit may require service please contact ADJ ADJ Products LLC will not accept any liability for any resulting dam ages caused by the non observance of this manual or any unauthor ized modification to this unit ADJ Products LLC www adj com Quad Scan Pro Instruction Manual Page 3 e TTET Meter lal ad ae Safety Precautions For Your Own Personal Safety Please Read and Understand This Manual Completely Before You Attempt To Install Or Operate This Unit To reduce the risk of electrical shock or fire do not expose this unit rain or moisture Do not spill water or other liquids into or on to your unit Do not attempt to operate this unit if the power cord has been frayed or broken Do not attempt to remove or break off the ground prong from the electrical cord This prong is used to reduce the risk of electrical shock and fire in case of an internal short Disconnect from main power before making any type of connection Do not remove the cover under any conditions There are no user serviceable parts inside N
8. and this mode is set the unit will automatically go into the last DMX set up 3 Press ENTER to confirm your desired set up LED With this function you can have the LED display turn off after 10 seconds 1 Press the MENU button until LED is displayed press ENTER 2 The display will show either ON or OFF Press the UP or DOWN buttons to select ON to keep the LED display on at all times or OFF to switch to have the LED display switch off after 10 seconds 3 Press the ENTER button to confirm PAN Pan Inversion 1 Tap the MENU button until PAN is displayed press ENTER Either Yes or No will be displayed 2 To activate the Pan inversion tap the UP or DOWN buttons until YES is displayed press ENTER to confim To deactivate Pan inver sion select NO and press Enter TILT Tilt Inversion 1 Tap the MENU button until TILT is displayed press ENTER Either YES or NO will be displayed 2 To activate the Tilt inversion tap the UP or DOWN buttons until YES is displayed press ENTER to confim To deactivate Tilt inver sion select NO and press Enter ADJ Products LLC www adj com Quad Scan Pro Instruction Manual Page 12 Quad Scan Pro System Menu DISP This will flip the LED display 180 1 Press the MENU button until dISP is displayed press ENTER 2 Either dISP or dSIP will now be displayed Press the UP or DOWN buttons to select one or the o
9. can Pro Operation confirm See pages 10 11 for more info 3 The optional UC3 Controller not included may be used to con trol different functions including blackout See page 16 for UC3 controls and functions Master Slave Operation This function will allow you to link up to 16 units together and operate without a controller The units will be sound activated In Master Slave operation one unit will act as the controlling unit and the others will react to the controlling units programs Any unit can act as a Master or as a Slave 1 Using approved DMX data cables daisy chain your units togeth er via the XLR connector on the rear of the units Remember the Male XLR connector is the input and the Female XLR connector is the output The first unit in the chain master will use the female XLR connector only The last unit in the chain will use the male XLR connector only For longer cable runs we suggest a termina tor at the last fixture 2 On the Master unit find your desired show and set that show by pressiing the ENTER button After you have set your desired show press the MENU button until SLND is displayed and Press ENTER Press the UP or DOWN buttons until MAST is dis played and press ENTER to confirm 3 On the slave units press the MENU button until SLND is dis played and press ENTER Press the UP or DOWN buttons until either SL 1 or SL 2 is displayed choose your desired slave mode and press EN
10. d this warranty does not include maintnance cleaning or periodic check up During the period specified above ADJ Products LLC will replace defective parts at its expense with new or refurbished parts and will absorb all expenses for warranty service and repair labor by reason of defects in material or workmanship The sole responsibility of ADJ Products LLC under this warranty shall be limited to the repair of the product or replacement thereof including parts at the sole discretion of ADJ Products LLC All products covered by this warranty were manufactured after August 15 2012 and bear indentifying marks to that effect ADJ Products LLC reserves the right to make changes in design and or improvements upon its products without any obligation to include these changes in any products theretofore manufactured No warranty whether expressed or implied is given or made with respect to any accessory supplied with products described above Except to the extent prohibited by applicable law all implied warranties made by ADJ Products LLC in connection with this product including warranties of merchantability or fitness are limited in duration to the warranty period set forth above And no warranties whether expressed or implied including warranties of merchantability or fitness shall apply to this product after said period has expired The consumer s and or Dealer s sole remedy shall be such repair or replacement as is expressly provided ab
11. dj com Quad Scan Pro Instruction Manual Page 17 e TTE Yo Ee LLIN od Xe 5 Channel Mode DMX Traits e TTE eo IoT La od o 32 Channel Mode DMX Traits Function Function 0 255 MIRROR 1 PAN 0 255 MIRROR 1 TILT on RED MIRROR 1 0 255 0 100 5 STATIC COLOR SEQUENCE COLOR SEQUENCE 1 COLOR SEQUENCE 2 COLOR SEQUENCE 3 COLOR SEQUENCE 4 COLOR SEQUENCE 5 COLOR SEQUENCE 6 COLOR SEQUENCE 7 pA GREEN MIRROR 1 0 255 0 100 E ee BLUE MIRROR 1 0 255 0 100 COLOR SEQUENCE 8 o 2ss WHITE MIRROR 1 COLOR SEQUENCE 9 0 255 0 100 Ae COLOR SEQUENCE 10 MASTER DIMMER MIRROR 1 COLOR SEQUENCE 11 0 100 COLOR SEQUENCE 12 STROBING MIRROR 1 COLOR SEQUENCE 13 OPEN COLOR SEQUENCE 14 STROBING SLOW FAST COLOR SEQUENCE 15 OPEN COLOR SEQUENCE 16 FAST CLOSE SLOW OPEN COLOR SEQUENCE 17 OPEN COLOR SEQUENCE 18 SLOW CLOSE FAST OPEN COLOR SEQUENCE 19 OPEN COLOR SEQUENCE 20 SOUND ACTIVE STROBING COLOR SEQUENCE 21 OPEN COLOR SEQUENCE 22 MIRROR 2 PAN COLOR SEQUENCE 23 COLOR SEQUENCE 24 RED MIRROR 2 COLOR SEQUENCE 25 0 100 COLOR SEQUENCE 26 GREEN MIRROR 2 COLOR SEQUENCE 27 0 100 COLOR SEQUENCE 28 BLUE MIRROR 2 COLOR SEQUENCE 29 0 100 COLOR SEQUENCE 30 WHITE MIRROR 2 COLOR SEQUENCE 31 0 100 COLOR SEQUENCE 32 MASTER DIMMER MIRROR 2 100 ADJ Products LLC www adj com Quad Scan Pro Instruction Manual Page 18 ae 0 255 www a com Quad Scan Pro Ins
12. e rigging option you choose for your Quad Scan Pro always be sure to secure your fixture with a safety cable not included Attach a safety cable to the provided safety bolt Caution For added protection mount the fixtures in areas out side of walking paths seating areas or areas were the fixture might be reached by unauthorized personal Before mounting the fixture to any surface make sure that the installation area can hold a minimum point load of 10 times the device s weight To avoid injury never stand directly below the device when mounting removing or servicing the fixture Always use and install a safety cable not included as a safety measure to prevent accidental damage and or injury in the event the clamp fails Be sure to complete all rigging and installation procedures before connecting the main power cord to the appropriate wall outlet ADJ Products LLC www adj com Quad Scan Pro Instruction Manual Page 5 e TTET Meter lal ad ae Set Up Power Supply The ADJ Quad Scan Pro contains a automatic volt age switch which will auto sense the voltage when it is plugged into the power source With this switch there is no need to worry about the correct power voltage this unit can be plugged in anywhere DMX 512 DMX is short for Digital Multiplex This is a universal pro tocol used by most lighting and controller manufactures as a form of communication between intelligent fixtures and controllers A DMX co
13. ever operate this unit when it s cover is removed Always be sure to mount this unit in an area that will allow proper ventilation Allow about 6 15cm between this device and a wall Do not attempt to operate this unit if it becomes damaged This unit is intended for indoor use only use of this product out doors voids all warranties Always mount this unit in safe and stable matter Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them paying particular attention to cords at plugs convenience recep tacles and the point where they exit from the appliance Cleaning The fixture should be cleaned only as recommended by the manufacturer See page 23 for cleaning details Heat This fixture should be situated away from heat sources such as radiators heat registers stoves or other appliances including amplifiers that produce heat The fixture should be serviced by qualified service personnel when A Objects have fallen or liquid has been spilled into the appliance B The appliance has been exposed to rain or water C The appliance does not appear to operate normally or exhibits a marked change in performance ADJ Products LLC www adj com Quad Scan Pro Instruction Manual Page 4 Quad Scan Pro Hanging Precautions Fixture installation must always be secured with a secondary safety attachment such as an appropriate safety cable Regardless of th
14. is unit is inserted in the female XLR connector of the last unit in your daisy chain to terminate the line Using a cable terminator ADJ part number Z DMX T will decrease the possibilities of erratic behavior Termination reduces signal errors and avoids signal transmission problems 3 and interference It is always advisable Dy p to connect a DMX terminal Resistanc 120 Ohm 1 4 W between PIN 2 DMX and PIN 3 DMX of the last fixture Figure 4 ADJ Products LLC www adj com Quad Scan Pro Instruction Manual Page 7 e TTE Yo ESTY TL dae Set Up Quad Scan Pro System Menu Chart 5 Pin XLR DMX Connectors Some manufactures use 5 pin DMX 512 data cables for DATA transmission in place of 3 pin 5 pin DMX A 7 S s DMX512 Address Setting fixtures may be implemented in a 3 pin DMX line When inserting stan J ic dard 5 pin data cables in to a 3 pin line a cable adaptor must be used re these adaptors are readily available at most electric stores The chart TAT x i Lod aL Channel Mode below details a proper cable con
15. lectrical equipment from power when not in use Thank you Quad Scan Pro General Information Unpacking Thank you for purchasing the Quad Scan Pro by ADJ Products LLCe Every Quad Scan Pro has been thoroughly tested and has been shipped in perfect operating condition Carefully check the shipping carton for damage that may have occurred during shipping If the carton appears to be damaged carefully inspect your fixture for any damage and be sure all equipment necessary to operate the unit has arrived intact In the event damage has been found or parts are missing please contact our toll free customer support number for fur ther instructions Please do not return this unit to your dealer without contacting customer support first Introduction The Quad Scan Pro is a DMX intelligent RGBW Quad Color LED scanner The Quad Scan Pro can operate as a stand alone fixture or in a Master Slave configuration The Quad Scan Pro has three operating modes sound active mode show mode and DMX control This fixture is suitable for theaters studios retail stores and other similar locations For best results use fog or special effects smoke to enhance the beams projections Customer Support ADJ Products LLC provides a toll free cus tomer support line to provide help and to answer any question should you encounter problems during your set up or initial operation You may also visit us on the web at www adj com for any comments or suggestions
16. ng possessions and territories It is the owner s responsibility to establish the date and place of purchase by acceptable evidence at the time service is sought For warranty service you must obtain a Return Authorization number RA before sending back the product please contact ADJ Products LLC Service Department at 800 322 6337 Send the pro duct only to the ADJ Products LLC factory All shipping charges must be pre paid If the requested repairs or service including parts replacement are within the terms of this warranty ADJ Products LLC will pay return shipping charges only to a designated point within the United States If the entire instru ment is sent it must be shipped in it s original package No accessories should be shipped with the product If any accessories are shipped with the product ADJ Products LLC shall have no liability whatsoever for loss of or damage to any such accessories nor for the safe return thereof This warranty is void if the serial number has been altered or removed if the product is modified in any manner which ADJ Products LLC concludes after inspection affects the reliability of the product if the product has been repaired or serviced by anyone other than the ADJ Products LLC factory unless prior written authorization was issued to purchaser by ADJ Products LLC if the product is damaged because not properly maintained as set forth in the instruction manual This is not a service contract an
17. nsure longevity and crisp out put 1 Use normal glass cleaner and a soft cloth to wipe down the out side casing 2 Use a brush to wipe down the cooling vents and fan grill Clean the external optics and mirror with glass cleaner and a soft cloth every 20 days 4 Clean the internal optics with glass cleaner and a soft cloth every 30 60 days 5 Always be sure to dry all parts completely before plugging the unit back in e TTF To ESTY LLI ge Trouble Shooting Trouble Shooting Listed below are a few common problems that you may encounter with solutions w No light output from the unit 1 Be sure the external fuse has not blown The fuse is located on the rear panel of the unit 2 Be sure the fuse holder is completely and properly seated Unit does not respond to sound 1 Low frequencies bass should cause the unit to react to sound Tapping on the microphone quiet or high pitched sounds may not activate the unit ADJ Products LLC www adj com Quad Scan Pro Instruction Manual Page 23 e TTET Meter lal ad ae Warranty MANUFACTURER S LIMITED WARRANTY A ADJ Products LLC hereby warrants to the original purchaser ADJ Products LLC products to be free of manufacturing defects in material and workmanship for a prescribed period from the date of purchase see specific warranty period on reverse This warranty shall be valid only if the product is purchased within the United States of America includi
18. ntroller sends DMX data instructions from the controller to the fix ture DMX data is sent as serial data that travels from fixture to fixture via the DATA IN and DATA OUT XLR terminals located on all DMX fixtures most controllers only have a DATA OUT terminal DMX Linking DMX is a language allowing all makes and models of different manufactures to be linked together and operate from a single controller as long as all fixtures and the controller are DMX compliant To ensure proper DMX data transmission when using several DMX fixtures try to use the shortest cable path possible The order in which fixtures are connected in a DMX line does not influence the DMX addressing For example a fixture assigned a DMX address of 1 may be placed anywhere in a DMX line at the beginning at the end or anywhere in the middle Therefore the first fixture controlled by the controller could be the last fixture in the chain When a fixture is assigned a DMX address of 1 the DMX controller knows to send DATA assigned to address 1 to that unit no matter where it is located in the DMX chain Data Cable DMX Cable Requirements For DMX and Master Slave Operation The Quad Scan Pro can be controlled via DMX 512 pro tocol The Quad Scan Pro can be a 1 5 or 32 channel DMX unit The DMX address is set electronically using the controls on the bottom panel of the unit Your unit and your DMX control ler require a approved DMX 512 110 Ohm Data
19. ound active mode 3 Press the ENTER and then press and hold the MENU button for at least 3 seconds to confirm SENS Sound sensitivity control 1 Press the MENU button until SENS is displayed press ENTER 2 The display will show a number between 0 100 Press the UP or DOWN buttons to adjust the sound sensitivity 0 being the least sen sitive and 100 the most sensitive 3 Press the ENTER button to confirm DNST This mode can be used as a precaution mode that in case the DMX signal is lost the operating mode chosen in the setup is the running mode the fixture will go into when the DMX signal is lost You can also set this as the operat ing mode you would like the unit to return to when power is applied 1 Press the MENU button until DNST is displayed press ENTER 2 Either MASL BLND or LAST will be displayed Choose an operating mode you would like the unit to start up in when power is applied or the DMX signal is lost MASL Master Slave If the DMX signal is lost or power is applied the unit will automatically go into Master Slave mode ADJ Products LLC www adj com Quad Scan Pro Instruction Manual Page 11 e TTET Mater lal ad ae System Menu BLND Blackout If the DMX signal is lost or power is applied the unit will automatically go into stand by mode e LAST Last State If the DMX signal is lost the fixture will stay in the last DMX set up If power is applied
20. ove and under no circumstances shall ADJ Products LLC be liable for any loss or damage direct or consequential arising out of the use of or inability to use this product This warranty is the only written warranty applicable to ADJ Products LLC Products and supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore published MANUFACTURER S LIMITED WARRANTY PERIODS e Lighting Products 1 year 365 days Limited Warranty Such as Special Effect Lighting Intelligent Lighting UV lighting Strobes Fog Machines Bubble Machines Mirror Balls Par Cans Trussing Lighting Stands etc excluding LED and lamps e Laser Products 90 Day Limited Warranty e L ED Products 2 year 730 days Limited Warranty excluding motors PCB boards and power supplies which have a 1 year 365 day Limited Warranty and batteries which have a 180 day limited warranty ADJ Products LLC www adj com Quad Scan Pro Instruction Manual Page 24 e TTE To EIT La od xe Notes ADJ Products LLC www adj com Quad Scan Pro Instruction Manual Page 25 e TTET Meter lal ad ae Specifications Model Quad Scan Pro Voltage 100 240V 50Hz 60Hz LEDs 4 X 10 Watt 4 in 1 RGBW LEDs Power Cord Daisy Chain 4 Fixtures Max Power Consumption 88W Dimensions 17 25 L x 14 25 W x5 25 H 438mm x 356mm x 133mm Colors RGBW Gobos 4 Gobo Size 20 5mm 12mm Viewable Weight 17 Lbs 7 5 kgs Fuse
21. rs to control the various DMX fixture traits Follow the instructions on page 10 to set the DMX address For longer cable runs more than a 100 feet use a terminator on the last fixture 6 For help operating in DMX mode consult the manual included with your DMX controller oe Sound Active Mode This mode allows either single unit or several units linked together to run to the beat of the music Note This mode runs in conjuction with show mode You should select a show previous to activating sound active mode 1 Press the MENU button until SOUN is displayed and press ENTER 2 Press the UP or DOWN buttons so that ON is displayed and press ENTER to confirm and then hold MENU for at least 2 3 sec onds 3 To adjust the sound sensitivity press the MENU button until SENS is displayed and press ENTER Use the UP or DOWN buttons to adjust sensitivity 4 The optional UC3 Controller not included may be used to con trol different functions including blackout See page 16 for UC3 controls and functions Show Mode In this mode you can select 1 of 16 shows to run This mode can run as just an ordinary show or with sound active mode 1 Press the MENU button until SHND is displayed and press ENTER 2 Press the UP or DOWN buttons until you find your desired show and press ENTER then press and hold MENU for 3 seconds to ADJ Products LLC www adj com Quad Scan Pro Instruction Manual Page 14 Quad S
22. t as a master or slave in a master slave configuration 1 Press the MENU button until SLND is displayed press ENTER Either MAST SL 1 or SL 2 will be displayed 2 Press the UP or DOWN buttons until your desired setting is dis played press ENTER to confim NOTE In a Master Slave configuration you can set one fixture to Master or Slave 1 SL 1 and then set the next fixture to Slave 2 SL 2 in doing this the fixtures will now have contrast movement to each other SHND SH 0 SH16 show modes 0 16 Factory programs Show mode can be run with sound activity or without For show mode to run without sound activity turn sound activity off 1 Press the MENU button until SHND is displayed press ENTER 2 Sh X will now be displayed X representing a number between ADJ Products LLC www adj com Quad Scan Pro Instruction Manual Page 10 Quad Scan Pro System Menu 0 16 Programs 0 16 are factory programs while Show 0 is random mode Press the UP or DOWN buttons to find your desired show and press the ENTER then press and hold the MENU button for at least 3 seconds to confirm SOUN Sound Active mode This mode will run in con junction with show mode 1 Press the MENU button until SOUN is displayed press ENTER 2 The display will show either ON or OFF Press the UP or DOWN buttons to select ON to activate sound active mode or OFF to deactivate s
23. ther 3 Press the ENTER button to confirm TEST This function will run a auto test program 1 Press the MENU button until TEST is displayed press ENTER 2 The fixture will now run a auto test FHRS with this function you can display the running time of the fixture 1 Press the MENU button until FHRS is displayed press ENTER 2 The running time of the fixture will now be displayed Press MENU to exit VER With this function you can display the version soft ware of the fixture 1 Press the MENU button until VER is displayed press ENTER 2 The software version will now be displayed Press MENU to exit RSET use this function to reset the unit 1 Press the MENU button until RSET is displayed press ENTER 2 The fixture will now reset ADJ Products LLC www adj com Quad Scan Pro Instruction Manual Page 13 Quad Scan Pro Operation Universal DMX Control This function allows you to use a univer sal DMX 512 controller to control the chases and patterns dimmer and strobe A DMX controller allows you to create unique programs tailored to your individual needs 1 The Quad Scan Pro can be a 1 5 or 32 DMX channel fixture See pages 16 21 for detailed description of the DMX values and traits 2 To control your fixture in DMX mode follow the set up procedures on pages 6 8 as well as the set up specifications that are includ ed with your DMX controller Use the controller s fade
24. truction Manual Page 19 e UE e Ee La od xe 32 Channel Mode DMX Traits Quad Scan Pro 32 Channel Mode DMX Traits STROBING MIRROR 2 MIRROR 4 TILT OPEN 27 RED MIRROR 4 STROBING SLOW FAST 0 100 OPEN GREEN MIRROR 4 FAST CLOSE SLOW OPEN 0 100 OPEN BLUE MIRROR 4 SLOW CLOSE FAST OPEN 0 100 OPEN WHITE MIRROR 4 SOUND ACTIVE STROBING 0 100 MASTER DIMMER MIRROR 4 0 100 STROBING MIRROR 4 OPEN STROBING SLOW FAST OPEN FAST CLOSE SLOW OPEN BLUE MIRROR 3 OPEN 0 100 SLOW CLOSE FAST OPEN HITE MIRROR 3 OPEN SOUND ACTIVE STROBING OPEN 0 100 STROBING MIRROR 3 OPEN STROBING SLOW FAST OPEN FAST CLOSE SLOW OPEN OPEN SLOW CLOSE FAST OPEN OPEN SOUND ACTIVE STROBING OPEN 0 255 MIRROR 4 PAN ADJ Products LLC www adj com Quad Scan Pro Instruction Manual Page 20 ADJ Products LLC www adj com Quad Scan Pro Instruction Manual Page 21 e TTE Yo So Ta ad Ko Gobo Replacement The Quad Scan Pro comes with 4 replaceable gobos This gobos can be interchanged at any time and allows you to customize your sys tem To replace gobo 1 Select the gobo you would like to replace and unscrew the thumb screw that is holding the gobo housing in place Note The thumb screw cannot be removed 2 Remove the gobo housing 3 Once the gobo housing has been removed remove the retaining ring that holds the gobo in This can easily be done using needle nose pliers
25. version Soe aCLr BASE 3 Pin XLR to 5 Pin XLR Conversion SLE i Slave Mode cl ja JU E 3 Pin XLR Female Out 5 Pin XLR Male In am Random Show llr SIR i Data True signal Pin SHB Not Used Pin4 DoNotUse _ as Seti Sound Mode Not Used Po Pin 5 Do Not Use ore o 0 5 E im 5 H Sound Sense Maa ot MENU NOCI CO LES g n m fmi a L E g DMX State toe Linc ro Orr Led LED Display an 20a n Pan Inversion JCI i L k Tilt Inversion JIa te a SIP Display Normal O Wit Te i f ft I 1 Display Inversion LIQ ZC At Auto Test n C 4 Fixture use time im a Software Version fe sl Pk Reset ADJ Products LLC www adj com Quad Scan Pro Instruction Manual Page 8 ADJ Products LLC www adj com Quad Scan Pro Instruction Manual Page 9 e TTET Meter lal ad ae System Menu ADDR DMX Address Setting 1 Press the either the MENU UP or DOWN buttons until ADDR is displayed press ENTER 2 The current address will now be displayed and flashing Press the UP or DOWN buttons to find your desired address Press ENTER to set your desired DMX address CHND This will let select your desired DMX channel mode 1 Press the either the MENU button until CHND is displayed press ENTER Either 1CH 5CH or 32CH will be displayed 2 Press the UP or DOWN buttons to find your desired DMX mode and press ENTER to confim and exit SLND This will let you set uni
Download Pdf Manuals
Related Search