Pedal Palette Manual
Contents
1. 34 decibel eleven Features Benefits and Operation 2013 Decibel Eleven N decibel eleven sere Features Benefits and Operation Contents Introduction Features Top Panel Controls Operation Basics Connections Rear Panel Diagram O o o 40 K MM M Order Swapping Parallel Mix Bus Tails Control Buffering Operating Modes Preset Control MIDI Control Settings Mode MIDI Sysex Data Dump Specifications Decl Decibel Eleven declares that this product complies with the European Union Council Directives and Standards requirements for the Low Voltage Directive 2006 95 EC and the EMC Directive 2004 108 EC Ce CL RoHs n of Conform 2013 Decibel Eleven Introduction The Pedal Palette at it s core is a four loop true bypass switcher designed to preserve guitar tone and signal when pedal effects are bypassed It features the ability to store and recall preset combinations of pedals enabling the user to switch multiple pedals in and out of the effect chain simultaneously with a single button press In addition to these base features the Pedal Palette expands your sonic palette by adding an available parallel mix bus to all effect returns and adding the ability to change the order of the effects on the fiy The Pedal Palette is a creative tool designed with an intuitive user interface making experimentation2. use what sounds best Reverb and Delay There are several practical advantages to using the Pedal Palette with delay and reverb pedals The direct guitar signal remains analog Since your dry sound is no longer obtained from the effect pedal your guitar signal will not be converted to digital and back again as some pedals do Also your dry guitar signal level remains consistent and it is not modified and re mixed at each reverb and delay pedal in the chain which can add noise Delay and reverb tails or echoes can continue to decay naturally after the effect is switched off Delay and reverb pedals that are true bypass must abruptly cut off the reverb and delay tails when switched off With the Pedal Palette their echo tails are allowed to fade out see Tails Control section page 12 Multiple delay and or reverb pedals active in an effects chain can all be fed the same input signal Using both a delay and a reverb on a source is a common technique in recording studios However the same result can not be achieved in a typical series pedal effect chain This is because in the series chain one of the two effects must always come first putting it s imprint on the sound before reaching the second effect With the Pedal Palette it is now possible to send the same input signal to both the reverb and delay effects and then mixing their wet outputs together with the dry signal using the parallel mix bus When usi
3. connection Use the MODE switch to select the desired mode When the loop is in PARALLEL mode it s return signal can be blended or mixed into the Pedal Palette signal path using the LEVEL knob and the PHASE sviitch For more information on loop modes see the Series Connection and Parallel Mix Bus sections page 8 amp 10 NOTE Changing the MODE settings can cause a loud click or snap with high gain amplifiers It is advised to keep volume low when switching these Controlling the Loop States The bottom row footswitches 1 4 are used to turn the loops on or off Status is indicated by the RED LED directly above the switch Swapping the Loop Order The top row footswitches are used to swap the order of the effects The right most footswitch will reverse the order of loops 1 amp 2 when activated It s status is indicated by the YELLOW LED directly below the footswitch The left most footswitch will reverse the order of loops 3 amp 4 when activated The center footswitch reverses the order of the loop 1 amp 2 section and the loop 3 amp 4 section when activated For more information on swapping see the Order Swapping section page 9 Input Buffer When the BUFFER switch in the upper right corner is set to IN the input buffer is active in circuit Setting the switch to OUT will bypass the input buffer circuit For more details on how Pedal Palette buffers work see the Buffering section page 13 Tails Control The TAILS switch in th
4. fed the clean guitar signal and the series effect is also fed the clean guitar signal creating a dual signal path The outputs from both effects are then mixed via the parallel mix bus With some experimentation many unique results can be achieved see Figure 4 Mi Cheat Effect Efect Effect Effect Output pier Pedal Pedal Le Pedal Le Pedal Le DEN 4 3 2 1 Parallel Mix Bus Figure 4A Parallel configuration Pedal 2 and Pedal 4 are PARALLEL oup rag Effect Efect Effect Effect Audio Ir G Pedal Pedal la Pedal Pedal Parallel Mix Bus Figure 4B Parallel configuration Pedal 2 amp Pedal 4 are PARALLEL Pedals 182 swapped Pedals 384 swapped section 1 2 amp 3 4 swapped T When using reverb and delay pedals it is often desired to have the tails or echoes decay naturally Con after the effect is shut off True bypass pedals inherently cut off the echoes abruptly when the pedal is turned off With the TAILS control on the Pedal Palette the send to the pedal will be muted when the loop is off But the pedal return will remain connected to the mix bus allowing the residual echoes to ring out This is a very useful feature when used with a reverb or delay pedal however it can be problematic when using the parallel mix bus with pedals that do not have echoes and which may be noisy For this reason each effect loop can be indiv
5. loop TAILS settings Refer to the TAILS Control Individual Loop Tails control section on page 12 MIDI Setup Enter settings mode as described above Entering SETTINGS MODE Press the B footswitch to select the setup for MIDI Channel and MIDI Echo Refer to the MIDI Control gt Setting the MIDI Channel and MIDI Echo sections page 15 16 MIDI Sysex Data Enter settings mode as described above Entering SETTINGS MODE Select the C footswitch to access the options for sending and receiving bulk MIDI system exclusive data Refer to the section MIDI Sysex Data Bulk Dump and Receive for details page 18 Factory Reset Enter settings mode as described above Entering SETTINGS MODE Select the D footswitch to load the menu for initiating a full factory reset The display will read r and the YELLOW middle SWAP LED will be lighted This procedure will erase all preset data and set all settings data to the factory defaults Selecting the middle SWAP footswitch enables alternating J and n options Selecting the LOOP 3 footswitch YES option will proceed to erase all preset data and restore settings to their factory default Make sure you absolutely want to do so before proceeding Selecting the LOOP 2 footswitch NO option returns to the main SETTINGS menu To return to the current operating mode press the STORE EDIT button i7 MIDI Sysex Data Bulk Dump and Receive The Pedal Palette is capable of sending and receiving all of it s setti
6. set the loop MODE slide switch to PARALLEL Once the switch is set to PARALLEL the loop s send signal is split and also sent to the following loop s send jack The return signal of the loop will now be routed to the parallel mix bus instead of to the next loop s send See Figure 3 below showing the signal routing when a loop is in parallel We Gran Output fest eect Efect Etot Audion lt Pedal seas Le Pedal la rea ERT 4 3 2 1 Parallel Mx B Figure 3 Parallel configuration Effect Pedal 2 is switched to PARALLEL mode Levi nd Phase Invert Controls When a loop is set to PARALLEL mode there are two additional controls which can be used to set the desired blend of the effect The LEVEL control is used to set the amount of effect return that is mixed in The PHASE switch inverts the phase of the effect return Some effect pedals will invert the phase of the signal such that their output is out of phase with their input With these types of effect pedals it will be necessary to use the INVERT position to correct the phase before mixing Other pedals may have some phase shift but may not be completely out of phase For these reasons some 10 experimentation with the PHASE switch settings is recommended If the effect gets weaker when the LEVEL control is turned all the way clockwise this is an indication that the effect is out of phase and the PHASE switch should be toggled In any case
7. simple and easy Reading the entire manual is not necessary to begin enjoying the benefits of the Pedal Palette but it is highly recommended for a full understanding of it s features and operation Features 4 Pedal Effects Loops True Relay Bypass Fully Analog Signal Path Swap Pedal Order Instantly Blend any effect in Parallel Reverb and Delay Tails Control Optional Discrete Class A Input Buffer 128 Presets Send and Receive MIDI Program changes Website Go to decibel11 com for videos manuals accessories and more Contact us directly at support amp decibel11 com Sue BANK DOWN SWAP iS an SWAP zx 1 d LOOP MODE BYPASS BANK UP INPUT BUFFER SWAP STATUS LED CONTROE T TATUS LEDS 8 aun RETURN PARALLEL RETURN 7 U Lens MASTER STOREVEDIT BUTTON Coto P 7 INVERT BN cio Cy Lr I LZ d is Ty I INT LLL PRESET LEDS BANK NUMBER PRESET LEDS ORA STATUS LED LOOP 3 STATUS LED DISPLAY LOOP 2 STATUS LED Loopt STATUS LED TOP PANEL CONTROLS Operation Basics This section describes the basic controls of the Pedal Palette It is meant as a general introduction and a guide for those wanting to get started immediately This section only covers DIRECT MODE functionality which is the factory set default mode For PRESET MODE operation see the Preset Control section page 14 Loop Mode Settings Each loop can be configured to have either a series or parallel
8. to the RETURN jack Connect your instrument to the INPUT jack and connect the OUTPUT jack to the amplifier additional pedal or other destination The Pedal Palette can also be used in the effect loop of an amplifier for parallel mixing of modulation pedals within the amp s loop The TUNER jack can be used for always on tuning Power The Pedal Palette can be powered by 9VDC or 12VDC at 300m It is highly recommended that a well regulated and isolated 12V 300mA minimum power supply is used for best performance The power inlet jack is a standard 2 1mm DC power jack center negative connection SII Simple setup with one pedal per loop Expanded setup with optional multiple pedals per loop and MIDI Di vn ve P ogo Go Ca AMP EFFECT LOOP SEND K 9 se errecriooe SERM A Emm Pedal Palette in Amplifier s Effect Loop Multiple Modulation Effects in Parallel T e eL foo 99 ee foo Gel e s 2 6 o o o o gt 10m_ Oo ve Expanded setup using two Pedal Palettes 6 9 12V DC REGULATED CENTER NEGATIVE 12V RECOMMENDED STORE EDIT BUTTON SEE a JL ofa Z aula ws DN cn Beuren Ee E m Gr 2 22 9 999900 FOS LOOPS RETURN Loop RETURN mois MDIOUT INSTRUMENT IN LOOP 1 RETURN oer 2 RETURN 6gp v
9. you can easily change to DIRECT MODE and make changes DIRECT MODE DIRECT MODE allows direct control over each loop state and swap state and is indicated when the numeric BANK display and the blue preset LEDs are not lighted The functions of the footswitches are indicated on the panel by white on red lettering This mode is used for direct real time control of the loop and swap states PRESET MODE PRESET MODE allows the Pedal Palette to recall stored switch configurations presets and is indicated by the lighted numeric BANK display and BLUE preset LEDs In this mode the functions for the footswitches are indicated on the top panel in gold lettering Preset Control The Pedal Palette features easy storing and recalling of preset switch configurations A preset in the Pedal Palette consists of the configuration and states of the stomp switches only This includes all LOOP ON OFF and SWAP ON OFF states A preset does not include the states of the slide switches they are considered global switches There are 128 available preset locations in the Pedal Palette Presets can be recalled directly in PRESET MODE or can be recalled using a MIDI controller see MIDI Control section In PRESET MODE the presets are configured in 32 banks of 4 presets The BANK display indicates the bank 1 32 and the blue preset LED indicates the preset A B C D within the bank To change the bank use the BANK UP and BANK DOWN switches Then select the pr
10. e Pedal Palette it is now possible to obtain these types of results with analog routing and mixing for your favorite pedal effects Cen Effect Effect Effet a Pea Le reg Le Pedal Le pana L 4 3 2 1 Figure 1 Series configurator Order Swapping Typically the order of your pedals in your effect chain is determined by trial and error and through general consensus However many times an alternate order of pedals can result in an equally useful and effective sound effect The Pedal Palette gives you the ability to swap the order of your effects in real time In some cases this can result in drastic differences This is particularly true with tone or frequency modifying effects such as distortion wah or EQ pedals In other cases the result is more subtle where one effect becomes more predominate than the other s Modifying effect pedal order is great when searching for just the right sound and it greatly expands your available sonic options The top row of footswitches labeled SWAP allow the order of the effects to be changed The right most SWAP switch reverses the order of loops 1 amp 2 The left most SWAP switch reverses the order of loops 3 amp 4 The middle SWAP switch reverses the order of the loop 1 amp 2 section and the loop 3 amp 4 section see Figure 2 This method allows many possible order combinations while still being intuitive and easy to understand The YELLOW swap status LEDs provide sim
11. e upper right corner is the master setting for tails control When this switch is set to IN with at least one loop in parallel mode the parallel mix bus circuit is always active With the Switch OUT the parallel mix bus is only active when a parallel mode loop is turned ON For additional control loops can be individually configured for tails in or out see Tails Control section page 12 Storing a Preset A loop combination can be stored as a preset by pressing and holding the STORE EDIT button The green STORE EDIT LED will light a bank number will be displayed and the BLUE preset LEDs will flash in sequence Select the preset location to store to by first using the BANK UP and BANK DOWN switches to select the desired bank and then using the bottom row footswitches to select the preset location A D within the bank Once the Bank Preset combination is selected press the STORE EDIT button again to save the preset and return to normal operation For more details see the Preset Control section page14 Connections Refer to the drawings below and to the REAR PANEL CONNECTIONS figure on page 7 Each loop of the Pedal Palette can accommodate one or more effect pedals The SEND jack of each loop is connected to the input of the pedal for that loop If more than one pedal is used in the loop then connect the SEND to the input of the first pedal in the loop Connect the output of the pedal or last pedal if more than one pedal is used in a loop
12. eda 100P2 SEND LOOP 3 SEND LooP4 SEND amr TUNER CUT REAR PANEL CONNECTIONS ie Bypass Passive guitar pickups are low level high impedance sources This means they are easily loaded down by all the various cable and connections required when using multiple effect pedals resulting in a loss of high frequency response Many effect pedals on the market employ circuitry that is active even when the effect is turned off While this design allows for silent switching the bypass circuitry typically has high harmonic distortion and minimal headroom both of which can greatly affect the tone and dynamics of your playing Other pedal designs use a bypass scheme where the effect s input circuitry remains connected even when bypassed This type of pedal continues to load the guitar signal even when the pedal is switched off These types of pedal bypass issues have a cumulative effect And with several pedals in your effect chain they can result in a loss of tone dynamics and high frequency response even when all your pedals are OFF A true bypass pedal will completely disconnect all circuitry from the guitar signal and will route the pedal input directly to the pedal output This provides the most pure signal path However even if all the pedals in your effect chain are true bypass there still exists the possibility of poor signal caused by all of the cables connectors and switches that your guitar signal must travel thr
13. eset using the A B C D switches Bypass The BYPASS footswitch can be used in PRESET MODE to clear the current preset When a preset is active pressing the BYPASS footswitch clears the SWAP states and bypasses all loops Since there is no current preset selected the BLUE preset LEDs will flash in sequence From this state any preset in any bank can be activated 14 Storing a preset in DIRECT MODE The Pedal Palette allows any configuration created in DIRECT MODE to easily be stored for later recall When you have a configuration that you wish to save simple press and hold the STORE EDIT button until the the green STORE EDIT LED lights The BANK display will now be lighted and the blue preset LEDs will be sequencing Select the preset location you wish to store by using the BANK UP and BANK DOWN buttons to select the bank and then press the PRESET button A B C D within the selected bank Once you have the preset location selected simply press the STORE EDIT button again All LEDs will flash to indicate that the preset was saved and the Pedal Palette will return to DIRECT MODE Editing a preset in PRESET MODE When in PRESET MODE a preset can be easily modified and re saved While in PRESET MODE select the preset you wish to edit and press and hold the STORE EDIT button The green STORE EDIT LED lights up and the preset LED and BANK number are displayed as flashing showing a reminder of what is being edited Now the LOOP and SWAP switche
14. idually configured for tails IN or OUT 12 Individual Loop Tails Control Individual TAILS control for each loop is configured in SETTINGS MODE To enter SETTINGS MODE press the SWAP 1 2 footswitch and the SWAP 3 4 footswitch simultaneously The display will read SE and the BLUE preset LEDs will sequence To enter SETTINGS TAILS select the A footswitch The display will now read EL and the current TAILS setting for the loops is displayed by the RED loop status LEDs The loop on off footswitches are used to set the TAILS mode for each loop When the RED loop status LED is lighted the TAILS for that loop is IN When the LED is off TAILS are OUT To exit SETTINGS TAILS press the STORE EDIT button once to return to the SETTINGS main menu and press STORE EDIT a second time to return to the current operating mode Master Tails Switch The top panel TAILS switch acts as a master switch for tails control When the TAILS switch is set to IN and there is at least one loop configured in PARALLEL mode the mix bus will always be active in circuit When the TAILS switch is OUT the mix bus is active in circuit only when a PARALLEL mode loop is active and the parallel mix bus is bypassed when no PARALLEL mode loops are active Buffering The Pedal Palette can be configured to be completely true bypass when all loops are off This is the case when the input BUFFER and TAILS switches are set to OUT However there are some configurations which requ
15. ire the use of buffers in the circuit such as when mixing in parallel or when a loop is active The Pedal Palette is designed such that any buffering required for a series configured signal path is done via low distortion discrete Class A circuitry For the parallel mix bus a high quality low noise opamp circuit is used to achieve maximum headroom and low distortion The optional input buffer is a low distortion discrete JFET input Class A circuit It can be used when desired to convert a high impedance signal source such as pickups to low impedance thereby eliminating the effects of capacitive loading and minimizing noise that may be caused by long cable runs When the input BUFFER is switched OUT and when LOOP1 is active and first in sequence not swapped the Pedal Palette input is directly connected to the LOOP1 send This is optimum for the use of fuzz or other effects that sound best when plugged in straight from the guitar This direct connection feature is unique to LOOP 1 only Loops 2 thru 4 are buffered when on even if first in sequence 13 Operating Modes The Pedal Palette has two operating modes DIRECT MODE and PRESET MODE Switching between the two modes is easily accomplished by pressing both the LOOP 1 and SWAP 1 2 footswitches simultaneously This allows the user to easily change between operating modes during performance For example if you are operating in PRESET MODE and decide you want to improvise
16. lette first connect the MIDI out of the sending device to the MIDI in jack on the Pedal Palette To begin waiting for the dump press the SWAP 1 2 footswitch The display will read 1n and the YELLOW SWAP 1 2 status LED will flash indicating that it is waiting for valid data Initiate sending from the sending device If the data is valid and received correctly the Pedal Palette will flash all LEDs twice and return to the SETTINGS DATA DUMP menu If the data is not received or is not valid then the Pedal Palette will ignore the data and not complete the write to memory To cancel out of the waiting for data state press the SWAP 1 2 footswitch again To exit out of SETTINGS DATA DUMP press the STORE EDIT button once to return to the SETTINGS menu and a second time to return to the current operating mode 18 Specifications Bypass method Input Impedance Max Input Level Frequency Response S N Ratio THD N Output impedance Max Output Level Power Dimensions Weight Relay True Bypass or Analog Buffered Input Buffer 1 MQ Loop Return 470 ko 16 dBu 0 0 0 2 dB 10 Hz 40 kHz gt 96 dB 0 dBV ref no weighting lt 0 004 10 dBV 20 Hz 30 kHz 4000 19 dBu into 10 KQ 9 12 VDC 300 mA center negative 12V DC isolated amp regulated recommended 13 2 x8 x 1 6 WxDxH 3 Ibs 19
17. ng delay and reverb pedals in PARALLEL mode with the Pedal Palette it is important to set the blend or mix setting on the pedals to 100 wet The blending will now be controlled with the loop s LEVEL control on the Pedal Palette In some pedals there may be an internal setting for kill dry which can also achieve the same result e Mixing Parallel effects mixing is widely used in recording studios as a creative tool for blending all types tive Uses of P effects to achieve a more distinctive soundscape Many of these same techniques can be applied using guitar pedal effects with the Pedal Palette For example the intensity of a chorus or flanger can be easily controlled by using a parallel mix bus to blend the amount of effected signal with the direct signal Mixing a compressor in parallel can fatten the sound while still retaining dynamics by blending the direct tone with a heavily compressed tone Likeviise a distortion pedal can be blended u with a clean tone to create a bigger more dynamic sound When used in combination with effects order swapping the parallel mix bus can yield some interesting results Many times parallel mixed effects such as delay are used at the end of the chain This allows additional series effects to be inserted in front of it with the result being that the delay receives the affected sound In the Pedal Palette if the order is swapped the result is that the delay is now
18. ngs and preset data via a MIDI system exclusive message This can be useful for backing up presets to a computer file or for copying presets from one Pedal Palette to another To do this first enter SETTINGS MODE by pressing both the SWAP 1 2 and SWAP 3 4 footswitches simultaneously The display will read SE and the menu options will be indicated by the BLUE preset LEDs Select the C footswitch to access the data dump menu The display will read dd and the YELLOW SWAP 1 2 and SWAP 3 4 LEDs will be lighted Sending a MIDI sysex data dump To send a MIDI sysex data dump of all preset data and global settings first connect the MIDI out jack directly to the MIDI in of the device you wish to send the dump to To initiate the data dump press the SWAP 3 4 footswitch The display will read DE while the YELLOW SWAP 3 4 status LED will flash rapidly Once the data dump is complete the display reverts to dd and the options for data dump and receive are again available To exit out of SETTINGS DATA DUMP press the STORE EDIT button Once to return to the SETTINGS menu and a second time to return to the current operating mode Receiving a MIDI sysex data dump A MIDI sysex bulk dump can be used to restore data from a previous backup or to duplicate the presets from another Pedal Palette Be aware that this procedure will overwrite the existing settings and preset data To receive a MIDI sysex data dump from a previously stored dump or from another Pedal Pa
19. nter SETTINGS MIDI mode as described in Setting the MIDI Channel above The middle BYPASS footswitch is used to set the MIDI Echo ON or OFF The YELLOW LED beneath the footswitch is lighted when MIDI Echo is enabled and not lighted when MIDI Echo is disabled Exit SETTINGS MIDI mode by pressing the STORE EDIT button twice MIDI output in PRESET MODE The Pedal Palette has 128 preset locations available corresponding to the 128 available MIDI Program Change Numbers In PRESET MODE these are configured as 32 banks of 4 presets When a preset footswitch is activated in PRESET MODE a MIDI Program Change 0 127 will be sent on the set MIDI channel This can be used to recall presets on another Pedal Palette or any other device capable of responding to MIDI Program Change messages The MIDI Program Change Number is fixed for each preset Bank 1 Preset A sends MIDI Program Change Number 0 Any desired preset mapping must be achieved within each individual controlled device MIDI Input in PRESET MODE In PRESET MODE a received MIDI Program Change message on the set MIDI channel will load the corresponding preset on the Pedal Palette This can be used for syncing a Pedal Palette to a master MIDI controller or another Pedal Palette MIDI input in DIRECT MODE When the Pedal Palette is in DIRECT MODE a MIDI Program Change received on the set MIDI Channel will load the corresponding preset This is useful for syncing the Pedal Palette to a maste
20. ough The Pedal Palette is a true bypass switcher The advantage to having all of your effect pedals connected through the Pedal Palette is that when all of the pedal loops are switched off your guitar signal goes directly from the input jack to the output jack bypassing all of the cables connectors and pedals in the effect chain In order to achieve a straight wire type of true bypass the Pedal Palette utilizes relays This provides the most transparent bypass possible However because relays are mechanical switches it is understood that they inherently cause some noise when switching when the Input Buffer and Tails switches are off Series Connection Guitar effect pedals are typically wired in what is known as a series configuration What this means is that the guitar is plugged into the first pedal the output of the first pedal goes to the input of the second pedal the output of the second pedal goes into the third pedal etc see Figure 1 This configuration makes it simple and easy to see what the signal path is However the series configuration is limited in several ways The series order of the effects is fixed and cannot be changed And the effects cannot be blended or mixed Digital multi effect processors have long been able to obtain more complex and flexible routing and mixing capabilities And recording engineers will often use multiple effects mixed in parallel to create lush and complex soundscapes With th
21. ple visual feedback making it ideal when swapping live and in real time LL swap Y 7x 607A wy Erect sied Kie Erect M a Pedal Le Pedal la Pedal Le Pedal ae 4 3 2 1 Figure 2 Series configuration Order Swapping Parallel Mix Bus Parallel mixing has long been a useful method of achieving a desired sound effect It is a standard method used with reverbs and delays All reverb and delay pedals have some type of parallel mixer built into them The signal seen at the input to the effect referred to as the dry signal is mixed with the delayed output of the effect the wet signal Some pedals convert the direct dry signal to digital and mix it with the wet signal digitally before converting back to analog Other pedals keep the direct dry signal analog and mix analog In many cases the mix is controlled through a blend knob which balances the amount of dry signal with the amount of effected wet signal The parallel mix bus in the Pedal Palette works in a similar way by taking the pedal s output at the loop return jack and mixing it with the dry signal obtained within the Pedal Palette In this case however since the Pedal Palette has more than one effect loop the dry signal is not always the signal at the input jack It could also be the signal output from any active SERIES mode loop s Setting a Loop in Parallel Mode To configure a loop in parallel
22. r MIDI controller or to another Pedal Palette Since the Pedal Palette is in DIRECT MODE the SWAP and LOOP footswitches are active allowing instant changes to be made to the loop and swap states at any time Storing Changes in DIRECT MODE When using MIDI to control the Pedal Palette in DIRECT MODE it is possible to make changes to a received preset and then store those changes instantly Once a MIDI Program Change message has been received on the set MIDI channel changes can then be made to the SWAP and LOOP states Pressing and holding the STORE EDIT button will now save these changes back to the preset location of the received MIDI Program Change If no MIDI Program Change message has previously been received on the set MIDI channel then pressing and holding the STORE EDIT button will allow the preset location to be selected see Preset Control Storing a Preset in DIRECT MODE above 16 SETTINGS MODE The Pedal Palette SETTINGS MODE is used for configuring individual loop TAILS control MIDI Channel MIDI Echo MIDI data dump and receive and for restoring the factory default settings Entering SETTINGS MODE To enter the SETTINGS MODE press the SWAP 1 2 and SWAP 3 4 footswitches simultaneously The numeric display will read SE The BLUE preset LEDs will flash in sequence indicating the options available TAILS Control Enter settings mode as described above Entering SETTINGS MODE Press the A footswitch to select the individual
23. s are active allowing for changes to the loop and swap states Once the changes have been made satisfactorily press the STORE EDIT button All LEDs will flash to indicate that the edited preset has been saved and the Pedal Palette will return to PRESET MODE MIDI Control The Pedal Palette can be set to send and receive MIDI Program Change commands In order to activate MIDI functionality a MIDI channel must first be selected in SETTINGS MODE Once a MIDI channel has been set the Pedal Palette will send MIDI Program Change messages while in PRESET MODE and will recall presets when receiving MIDI Program Changes in DIRECT and PRESET MODE Setting the MIDI Channel To enter SETTINGS MODE on the Pedal Palette press the SWAP 1 2 and SWAP 3 4 footswitches at the same time The display will read SE Select the B footswitch to enter SETTINGS MIDI The numeric display will now alternate between the current MIDI Channel and CH Use the BANK UP and BANK DOWN footswitches to select the desired channel 1 16 To deactivate MIDI functionality select the dash dash 7 Exit SETTINGS MIDI by pressing the STORE EDIT button once to return to SETTINGS MODE and a second time to return to the current operating mode MIDI Echo The Pedal Palette can be set to echo incoming MIDI commands to it s MIDI OUT port This can be 15 useful when using a master MIDI controller to control other MIDI devices in addition to the Pedal Palette To enable MIDI echo e
Download Pdf Manuals
Related Search