Jockey & Jockey Plus
Contents
1. Jockey amp Jockey Plus User manual A kra bat Jockey amp Jockey Plus General 05 Main components 06 Use 10 Accessories 16 Maintenance 19 Adjustment adaption 19 Warranty 20 Q krabat General This user manual gives an overview of the Krabat Jockey with both electric and manual elevation of the sitting unit Krabat jockey comes in two different sizes Many configurations are possible with different accessories Krabat Jockey is an active chair for children between the age 2 14 years 2 sizes The chair is height adjustable and can be adjusted from floor level to the height of a kitchen worktop The sitting position can be adapted to the individual child All angles and positions can be set infinitely An occupational therapist or a physiotherapist should determine the use of this chair The excellent sitting position provided by the Krabat jockey is due to both the saddle seat which promotes a neutral position in the pelvis and abduction in the hips and the footrests that support the feet in an optimal position The chair promotes good stability in the lower body and gives the spinal column natural curves This provides a good base for balance and activity in the trunk and upper body The saddle seat enhances an active sitting position rather than a slumped and passive position The upright and active position will also benefit speech swallowing and respiration To ensure an optimal sitting posit2. RABAT user manual following the actual KRABAT product purchased 3 KRABAT will at its own cost either itself or by assistance of a third party within reasonable time offer assistance in order to remedy any defect of substance to the KRABAT product which occurs within the said Warranty Period either by taking the unit in question for repair or by forwarding spares for replacement provided however the purchaser of the KRABAT product without undue delay after having become aware of the defect s in writing has notified KRABAT or a representative authorized by KRABAT of the discovered defect s However KRABAT retains the right at its sole discretion in lieu of performing remedial work to forward a new unit in lieu of the unit having defects or being defective In respect of forwarding spare or replacement parts or a new unit KRABAT or its authorized representative shall be deemed to have fulfilled its obligation in so far the part s or unit s in question are made available for collection at the offices from where the initial KRABAT product was sold 20 10 11 12 In the event where a defect has not been successfully remedied The purchaser shall be entitled to a reduction of the purchase price in proportion to the reduced value of the KRABAT product provided that under no circumstances shall such reduction exceed fifteen per cent 15 of the purchase price for the said KRABAT product or II Where the defect is so material a
3. components 01 Saddle seat with adjustable angle of the sitting unit 02 High backrest with adjustable angle and height 03 Adjustable individual footrests or footrest in one 04 Undercarriage 05 Wheels with individual brakes 06 Push handle with integrated operation key for elevation 07 Central bail 08 Adjustable side supports 09 Adjustable head support accessories 10 Harness accessories 11 4 mm Allen key for adjustments of head and side supports is positioned under the seat 13 Main components Jockey Plus w electric elevation Fig o4 Krabat Jockey Plus with electric elevation has the following main components 01 Saddle seat with adjustable angle of the sitting unit 02 High backrest with adjustable angle and height 03 Adjustable individual footrests or footrest in one 04 Undercarriage 05 Wheels with individual brakes 06 Push handle with integrated operation key for elevation 07 Central bail 08 Adjustable side supports 09 Adjustable head support accessories 10 Harness accessories 11 4 mm Allen key for adjustments of head and side supports is positioned under the seat 12 Battery 13 Charger 14 Power cord Q krabat Use To obtain the optimal sitting position the angles of the seat backrest and footrest need to be adjusted This should be done by a therapist who has received training from Krabat AS or a representative for Krabat AS All angles can be adjusted infinitely The individual footre
4. djustment to ensure the child s foot is in the correct position Fig 06 Adjustment of footrest in one 11 Q krabat Angle of the sitting unit Place the child on the saddle seat and tighten the belt Make sure the child is placed well into the seat in the midline position with symmetry in the legs lower body Use the hip belt to both maintain the position in the saddle seat and to reduce the risk of falling out of the chair It should be used at all times The angle of the sitting unit can be adjusted using the revolving tube underneath the seat The angle is self locking and does not need to be fixed Fig 07 Adjustment of the seat angle Angle and height of backrest The angle of the backrest can be adjusted and fixed using the locking lever If the locking lever does not fix the backrest properly it can be tighten using the plastic ring under the lever The height of the back rest can be adjusted by loosening the locking lever before sliding the backrest up or down in 5 different position each with 1 cm interval Remember to fix or tighten the locking lever when you have achieved the correct height Fig 08 Adjustment of the angle and height of the backrest Adjustment of the side supports Jockey Plus The side supports can be adjusted up or down by loosening the screws shown in figure 09 It is enough to loosen the screws dismantling is not required Tighten the screws after adjustment The side sup
5. ercarriage to the front It is advisable to lift the chair into the bag by holding on to the part of the undercarriage closest to the floor Make sure the push handle is fitted in the intended end of the bag The bag has an adjustable shoulder strap to make transport easier Fig 18 Folding into transport bag 16 Mounting of bracket for table and support handle if not pre mounted Unscrew the three screws in the cup holder and throw them away figure 19 Attach the bracket in the cup holder as shown in figure 20 using the accompanying three screws Fix the three screws using a 3 mm Allen key not included Make sure the button locking the table is pointing to the left for the child in the chair figure 21 Fig 20 Fig 21 17 Q krabat Table Pull out the button shown in figure 22 and keep it out Place the table in the bracket and let go of the button when the table is at the desired height As shown in figure 23 there are three different positions for the height Make sure the table is locked figure 24 Loosen the screw shown on figure 25 using the accompanying 4 mm Allen key Rotate the table to the desired position angle and tighten the screw The depth of the table can be adjusted in three different positions by loosening the 4 screws on the top surface figure 26 Use the accompanying 4 mm Allen key Place the table in the desired depth and tighten the screws Fig 26 18 Support handle Pull o
6. igure 14 When elevating the child you need to press down the operation key with one hand whilst assisting the elevation with the other hand Assistance is also needed when lowering the sitting unit The spherical handle shown in figure 15 is designed for this purpose Fig 14 Adjustment of the height 14 Manual elevation The elevation mechanism moves slowly Any attempt to elevate or lower quickly will cause resistance When adjusting the height of the sitting unit both seat and handle move at the same time Always use both hands when adjusting the height One hand on the push handle and one hand on the spherical handle fig 15 Fig 15 Handle for height adjustment Adjustment of the height Electric elevation The adjustment of the height is controlled by the remote control The remote control shown in figure 16 has one button for elevation and one for lowering As soon as you let go of the button the movement will stop A beeping sound will be heard when the sitting unit is in the highest or lowest position to let us know the sitting unit has reached the end position If a beeping sound is heard whilst the sitting unit is moving up or down the battery needs charging Fig 16 Electrical adjustment of height Battery and charging unit The battery is placed in the holder under the under carriage shown in figure 2 There are magnets in the battery to ensure the correct position in both holder and charger When a fu
7. ion it is important to try out and adjust the chair before use Do not use the chair unless an individual trial has been carried out Furthermore do not let other children use the chair without an individual trial As children grow they change their movement and sitting pattern on a regular basis It is likely that the child will need another size of the sitting unit or other adjustments Contact your local physiotherapist or occupational therapist if the product is not optimal or if adjustments are needed Q krabat Main components Jockey w manual elevation Krabat Jockey with manual elevation has the following main components 01 Saddle seat with adjustable angle of the sitting unit 02 Adjustable backrest 03 Adjustable individual footrests or footrest in one 04 Undercarriage 05 Wheels with individual brakes 06 Push handle with integrated operation key for elevation 07 Central bail Fig 01 Main components Jockey w electric elevation Fig 02 Krabat Jockey with electric elevation has the following main components 01 Saddle seat with adjustable angle of the sitting unit 02 Adjustable backrest 03 Adjustable individual footrests or footrest in one 04 Undercarriage 05 Wheels with individual brakes 06 Remote control 07 Central bail 08 Battery 09 Charger 10 Power cord Q krabat Main components Jockey Plus w manual elevation rig o3 Krabat Jockey Plus with manual elevation has the following main
8. lly charged battery is placed in the holder it will orientate itself to the correct position An audible beep indicates good connection and a system ready for use If a beeping sound is heard whilst the chair is not in use the battery needs charging The same applies if a beeping sound is heard whilst the sitting unit is moving up or down When charging the battery remove it from the holder When connecting the charger to a socket using the power cord a yellow light will indicate power Place the battery in the charger and it will orientate itself to the correct position See figure 17 A flashing green light will indicate the battery being charged When the battery is fully charged the green light will come on continuously Charging an empty battery will take approximately 5 8 hours This type of battery NiMH tolerates charging even if it is not totally empty Fig 17 Charging of the battery Yellow led power Green led charging fully charged Charger Battery 15 Q krabat Accessories There is a Wide range of accessories for the Krabat Jockey such as table different harnesses ankle cuffs bag etc See www krabat com for an updated list of accessories User manual for the different accessories follows the product Bag The Krabat Jockey is foldable making transport in a specially designed bag easier Fold the backrest and put the sitting unit in the lowest position Swing the rear part of the und
9. m KRABAT This WARRANTY does not cover normal wear and tear KRABAT shall not under any circumstances be liable for defects in any part of a KRABAT product for more than two 2 years from delivery Save as set out above under this WARRANTY KRABAT as well as its authorized representatives shall not be liable for any defects of the KRABAT product This applies to any loss the defect may cause including loss of production loss of profit and other indirect loss 21
10. ports can be adjusted in or out in the same way Fig 09 Adjustment of the side supports 12 Adjustment of the head support Jockey Plus The head support can be adjusted up or down by loose ning the screw shown in figure 10 Use the accompanying 4mm Allen key shown in figure 03 and 04 It is enough to loosen the screw dismantling is not required Tighten the screw after adjustment The head support can be adjusted in or out by loose ning the screw shown in figure 11 The head support can now be rotated as well It is enough to loosen the screw dismantling is not required Tighten the screw after adjustment The angle of the head support can be adjusted by loosening the screws shown in figure 12 Sideways adjustment of the head support is also possible in this operation It is enough to loosen the screw dismantling is not required Tighten the screw after adjustment The head support can be adjusted along the track shown in figure 13 in order to support the side of the head if needed Simply loosen the screws shown in figure 13 before sliding along the track It is enough to loosen the screws dismantling is not required Tighten the screws after adjustment Fig 12 Angle of the head support Fig 13 Lateral adjustment of the head support 13 Q krabat Adjustment of the height The height of the sitting unit can be adjusted by pressing down the integrated operation key on the push handle See f
11. s to significantly deprive the purchaser of the benefit of the purpose of the purchase the purchaser may terminate the purchase in respect of the defective KRABAT product The purchaser shall then be entitled to actual loss suffered if any however limited to a maximum of fifteen per cent 15 of the purchase price for the said KRABAT product This WARRANTY does not give any guarantees apart from those expressly given under this WARRANTY For avoidance of doubt This WARRANTY does not extend to any liability of KRABAT or its authorized representatives in respect of any indirect or consequential loss or damage suffered by the purchaser or any person the purchaser either deliberately or undeliberately gives access to the KRABAT product This WARRANTY does not apply in so far that the KRABAT product is supplemented with or there are changed parts of the KRABAT product with parts not manufactured by KRABAT or with parts manufactured or provided by others and the use thereof is of not authorized in writing by KRABAT KRABAT shall only be liable for defects which appear under conditions of operation or use provided for in the relevant user manual following the KRABAT product KRABAT shall not be liable for defects which are caused by faulty maintenance incorrect adjustments or faulty repair by any other person than KRABAT or representative authorized by KRABAT or any alterations to the KRABAT product carried out without the prior written consent fro
12. s to the KRABAT product observe and adhere to the following SAFETY PRECAUTIONS Always make sure to have read and understood the relevant user manual for the actual KRABAT product before taking into it use II The KRABAT product is only meant to be used for its intended purpose in accordance with the KRABAT user manual for the relevant KRABAT product III Never leave a child or any other user using the KRABAT product without proper adult supervision IV Always make sure that safety belts are properly fit and fastened and do not malfunction as well as recheck the foresaid at regular intervals when the KRABAT product is in use V Always use the KRABAT product with due regard to the advice of your physiotherapist or occupational therapist V Always remember that the KRABAT product is NOT a toy and hence never let a child or any one else play with the KRABAT product as it can harm both persons and the product as well as causing damage VI Always when not in use store the KRABAT product in a safe manner in order for it not to be misused by anyone and furthermore for the purpose of not exposing the KRABAT product to conditions that may harm it and or its functions 2 Subject to the terms and conditions of the WARRANTY KRABAT warrants that the KRABAT product for a period of one 1 year the Warranty Period from the purchase of the KRABAT product shall function in accordance with its intended purpose as set out in the K
13. sts can be adjusted using the 4 locking levers shown in fig 5 The footrest in one can be adjusted using two locking levers shown in fig 6 The sitting unit can be adjusted using the revolving tube shown in fig 7 The angle of the backrest can be fixed in different positions using the locking lever shown in fig 8 The use of the chair should be discussed with your therapist or someone who knows the child well It is important to establish in which situations the child should use the chair how long they should use it and when to progress the time spell This needs to be evaluated continuously as the child gets familiar with the chair 10 Individual footrests Place the feet on the footrests and tighten the belts Children who use ankle foot orthotics should wear these together with their shoes whilst sitting in the Krabat Jockey The height of the footrests is adjusted by sliding them up or down the tracks or simply by adjusting the length of the strap which is attached underneath the seat It is also possible to attach ankle straps on the footrests These will need adjustment to ensure the child s foot is in the correct position Fig 05 Adjustment of individual footrests Footrest in one The height of the footrests is adjusted by sliding them up or down the tracks or simply by adjusting the length of the strap which is attached underneath the seat It is also possible to attach ankle straps on the footrest These will need a
14. ut the button shown in figure 27 and keep it out Place the support handle in the bracket and let go of the button when the handle is in the desired height As shown in figure 28 there are three different positions for the height Make sure the support handle is locked figure 29 Fig 27 Fig 28 Fig 29 Maintenance All metal and plastic parts can be cleaned using mild soapy water The seat and backrest is covered with upholstery and can be cleaned using either a cloth and soapy water or machine washed at 40 degrees Celsius The textile is fastened to the chair with Velcro Advice about spot removal is given at www krabat com Bearings and other movable parts are maintenance free and should not be lubricated Individual adjustments and adaptations If the sitting unit for some reason needs adjustment please contact a physiotherapist or an occupational therapist Adaptations of the sitting unit must be made by qualified personnel or Krabat AS Do not under any circumstances make any modifications by yourself 19 Q krabat Warranty Manufacturer of the Krabat products Krabat AS hereinafter referred to as KRABAT having its place of business at Ravnsborgveien 56 1395 Hvalstad Asker Norway gives the purchaser of a KRABAT product the following product warranty hereinafter referred to as the WARRANTY 1 This WARRANTY is given upon the strict condition that the purchaser and any person that the purchaser gives acces
Download Pdf Manuals
Related Search