UCAT-S
Contents
1. MAINTENANCE Your UCAT S requires no maintenance Product Limited Warranty All Labelmate Products are warranted to the original end user customer to be free from defects in materials and workmanship If it is determined by Labelmate that a product has failed under the terms of this warranty the product will be repaired or replaced at no charge to the customer Labelmate reserves all rights to determination of coverage and liability under this warranty The warranty period for all new Labelmate products is outlined below Warranty Period Products Covered Label Rewinders meals Label Unwinders Label Counters mechanical parts only Label Slitters mechanical parts only Label Dispensers Printer Mechanisms Power Supply Modules Counter modules Encoders Any products not specified above The warranty period for all products starts on the date purchased by the original end user customer Warranty coverage is not transferable with ownership and will terminate immediately upon rental resale or any other change in ownership This warranty does not cover repair to any product which is damaged has been modified is missing parts or has been opened or repaired by any unauthorised person Use of any unauthorised accessory or attachment will void coverage Purchase documentation should be retained for coverage verification In the event your product requires service please contact the distributor you bought the product from The cus2. flat it is to be fixed using the holes in the base plate e The ambient light of the working area needs to be sufficient to avoid any risk e The unwinder can be used in ambient temperatures of 2 C to 40 C SET UP 1 Slide the Flange Plate onto the brass shaft 2 Install the three 3 metal vanes onto the shaft The side with the 3 holes for the screws has to be facing the rotation direction 3 Position the Plastic Flange Plate even with the inside end of the Shaft so there is clearance between the Flange and the Chassis Tighten the screw in the Hub until it is snug 5 CAUTION AVOID ACCIDENTS THE UCAT S WEIGHS OVER 6KG SO CHOOSE ONLY A STURDY SURFACE ON WHICH TO SET THE UNIT Your UCAT S is now ready for use rs WARNING This Product is for indoor use only Not for use in wet locations LABEL UNWINDING The UCAT S is bi directional It can unwind labels in either direction 1 Slide the roll of labels to be unwound slit onto the shaft of the UCAT S and all the way up against the Plastic Flange Plate 2 Thread the labels into the printer slitter as required 3 Begin the printing operation and observe that the labels are feeding correctly into your printer slitter If necessary adjust the position of the UCAT S so the alignment with the printer slitter is appropriate to correctly feed the labels 4 Braking is adjusted by turning the red knob LOADING HEAVY ROLLS In order to ease the loadin
3. g of heavy rolls on the UCAT S the unit can be placed on its back Slide the roll on the shaft and then reposition the unit straight OPTIONAL The tension is adjustable via the red knob This knob can be replaced with a regular M5 screw so the adjustment can only be made with a wrench in order to prevent the operator to change the brake setting
4. tomer assumes responsibility for all cost and risk incurred in transport for service Labelmate makes no other warranty of any kind expressed or implied or to suitability or fitness for a particular purpose No other person agent or reseller is authorised to give any warranties on behalf of Labelmate Any obligation to warranty other than that specifically addressed above is hereby disclaimed LABELMATE LLC 69 AVENUE ALPHONSE XIII 1180 BRUSSELS BELGIUM TEL 322 375 69 60 FAX 322 375 38 96 brussels labelmate com www labelmateeurope com LABELMATE User_UCAT S CE 08 14 Original user manual UCAT S Economy Label Unwinder with Adjustable Wearless Braking e Low cost economy Unwinder e Adjustable Braking e Non Powered Remove all parts from the shipping container and verify contents PACKAGE CONTENTS e User Manual this document e UCAT S Unit e Plastic bag with three 3 vanes and 6 screws e One 300mm Plastic Inner Flange Plate Retain the Shipping Container and Packaging for Storage and Transport SPECIFICATIONS Weight of the machine 6kg Max Label Roll Weight 6Kg Max Label Roll Diam 300mm e KEEP MANUAL IN A SAFE PLACE FOR FUTURE REFERENCE e IMPORTANT INFORMATION e This product is a label unwinder It is only to be used to unwind labels of the recommended dimensions and weight in an indoor dry environment e The machine is to be used on a flat surface if the surface is not
Download Pdf Manuals
Related Search
UCAT S ucat score calculator ucat score converter ucat score ucat shortcuts ucat sign up ucat sections ucat schedule ucat sjt ucat sample questions ucat syllabus ucat scaled score calculator ucat situational judgement ucat scores 2024 ucat score converter 2025 ucat section timings ucat score conversion table ucat score calculator 2025 ucat score calculator 2024 ucat situational judgement practice ucat score required for medicine ucat schedule ulster co ny