P RO FE SSIO N A L SER IE S
Contents
1. Be careful not to come in contact with any steam coming from the clear center lid 1 10 POWER CORD PRECAUTIONS NEVER operate with a damaged cord or plug If the supply cord is damaged it must be replaced by the manufacturer or authorized service agent to avoid a hazard DO NOT permit the cord to hang over the edge of the work surface NEVER use an extension cord with the unit Unplug the blender motor when not in use before changing blender locations or cleaning 1 11 NEVER ATTEMPT TO REPAIR THE POWER UNIT Never remove the blender motor cover The blender motor does not contain self adjustable or serviceable parts A qualified service agent must make all service adjustments Removing the cover or attempting to service the blender will void the warranty 1 12 TURN THE POWER TO THE BLENDER OFF WHEN NOT IN USE 1 13 AVOID TOUCHING THE BLENDER DRIVE SOCKET OR JAR SHAFT AFTER USE The blender drive socket and jar shaft may become very hot after blend cycles 1 14 SAFETY This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety Children should be supervised to ensure that they do not play with the appliance 1 15 THIS BLENDER IS INTENDED FOR HOME USE ONLY ANY USE OF THE BLENDER FOR COMMERCIAL PU2. the motor housing Clear Vented Cap Insert Lid FIGURE 5 BLENDER JAR ASSEMBLY Blade Assembly FIGURE 6 SOUND ENCLOSURE 10 FIGURE 7 BLENDER DIMENSIONS i 244 i 620mm 8 5 217 mm 9 0 4 1 230 mm 104 mm 4 2 2 QUICK RECIPE INSTRUCTIONS USE THESE STEPS TO GET STARTED RIGHT AWAY 1 Choose a recipe and gather ingredients try blendtec com recipes 2 Load the blender jar and secure the lid tightly 3 Place the jar onto the motor base and ensure power is turned on 4 Close the sound enclosure lid and press the appropriate blend icon 5 Enjoy For best cleaning results clean immediately after blending See CARE AND CLEANING 5 1 4 2 3 PROFESSIONAL 800 INTERFACE Power Capacitive Touch Slider Cancel Exit Preprogrammed Blend Cycles 4 2 4 ALL ABOUT BLEND CYCLES 12 Blend cycles are timed cycles designed for specific types of blends These one touch cycles speed up slow down and shut off automatically so results are perfect every time Each blender in the Professional series features a number of pre programmed cycles and settings that provide a wide range of recipes and functions Batters Sauces dips dressings batters Mixed Drinks mixed drinks milkshakes crush ice O Smoothie ruit smoothies green smoothies milkshakes Frozen Treats ice cream frozen yogurt sorbets Whole Juice juices green drinks Hot Soup soups hot chocolate syrup
3. BASE Blender Drive Socket Motor Base Cover wlendtec aO C Touch Pad LCD Information Center Motor Base Housing Power Switch Power Unit FIGURE 3 1 4 32mm 5 1 2 129mm L i Aco 3 76mm MAMUN e 8 1 2 205mm Countertop Hole Template 5 78 149 22 mm 4 111125 mm gt 4 1 2 QUICK RECIPE INSTRUCTIONS USE THESE STEPS TO GET STARTED RIGHT AWAY 1 Choose a recipe from the included Blending 101 booklet 2 Gather all of the ingredients 3 Load the blender jar as indicated in the recipe 4 Attach the blender lid to the jar ensure that it sits on the jar completely 5 Plug in the blender and turn on power by using the switch located in the front of the blender base 6 Place the blender jar onto the base making sure the jar is secure and fully seated on the motor base 7 Press the indicated icon from the recipe once or as indicated in the recipe 8 When cycle is complete remove the blender jar from the motor base 9 Remove the jar lid and serve as indicated in the recipe 10 For best cleaning results clean immediately after blending See CARE AND CLEANING 5 1 4 1 3 PROFESSIONAL 750 INTERFACE Speed Up Speed Down Power Indicator Light blendtec D Preprogrammed Blend Cycles 4 1 4 ALL ABOUT BLEND CYCLES Blend cycles are timed cycles designed for specific types of blends These one touch
4. cycles speed up slow down and shut off automatically so results are perfect every time Each blender in the Professional series features a number of pre programmed cycles and settings that provide a wide range of recipes and functions Batters Sauces dips dressings batters Mixed Drinks mixed drinks milkshakes crush ice Smoothie fruit smoothies green smoothies milkshakes Frozen Treats ice cream frozen yogurt sorbets Whole Juice juices green drinks Hot Soup soups hot chocolate syrups fondues Pulse stir chop or mince at a high speed BATTERS his cycle stays at relatively low speeds for shorter periods of time This combines your batters allowing the flavors to blend together properly without over mixing To use the Batters cycle load your jar as indicated in the recipe you are using secure the lid and press the Batters icon The blender will run the cycle and automatically shut off MIXED DRINKS This cycle is used for mixed drinks iced coffees and milkshakes The length of time creates a consistency that is ideal for these types of recipes To use the Mixed Drinks cycle load your jar as indicated in the recipe you are using secure the lid and press the Mixed Drinks icon SMOOTHIE This cycle is designed specifically for various types of smoothies and thick drinks that frequently use dense or frozen ingredients It slows down and speeds up automatically during the course of
5. the blade generates enough heat to warm the ingredients Do not add any liquids or ingredients over 115 F to the jar when preparing soups or hot items PULSE Use Pulse for chopping mincing whipping or other tasks that do not require a long blend cycle You can also Pulse to quickly stir a blend before serving The Pulse setting runs at speed 7 and will only run while the Pulse icon remains pressed When the icon is released the motor shuts off 4 2 PROFESSIONAL 800 4 2 1 INSTALLATION 1 Select a location for the blender that is near an electrical outlet and which allows enough room above and around the unit to allow for unobstructed movement of the sound enclosure see Figure 5 for measurements 2 Place the blender on a flat clean and dry surface Blender vents on the sides and exhaust on the back should be unobstructed to allow proper cooling during use 3 Plug the unit into an outlet with appropriate electrical protection FIGURE 4 BLENDER MOTOR BASE Control Surface ML Drive Socket Capacitive touch LED Direct drive coupling with the jar interface with intuitive blade shaft The socket has a control icons and ifetime warranty information screen Blender Motor Contains the machinery that runs he blender including the electric motor and drive train Motor Housing Houses all componenets and optimizes sound and airflow for cooler quieter operation Never remove
6. the cycle This allows the blender to draw the ingredients into the blending vortex creating the desired texture To use the Smoothie cycle load your jar as indicated in the recipe you are using secure the lid and press the Smoothie icon The blender will run the cycle and automatically shut off FROZEN TREATS This cycle is designed specifically for frozen treats including ice cream sorbets and frozen yogurt The cycle speeds up and slows down at the appropriate moments to ensure your blends stay frozen To use the Frozen Treats cycle load your jar as indicated in the recipe you are using secure the lid and press the Frozen Treats icon The blender will run the cycle and automatically shut off After creating your frozen dessert serve immediately and store leftovers in the freezer WHOLE JUICE This cycle is designed to completely blend tough and dense ingredients including carrots celery and seeds Use the Whole Juice cycle if you are using any fruits and or vegetables with stems seeds or skins When blending carrot juice or other dense juices you may need to repeat this cycle once or twice until the desired texture and consistency are achieved HOT SOUP This cycle is designed for hot recipes The cycle s length of time combined with the speed of the motor heats the ingredients to a hot temperature This cycle can also be used for hot chocolate syrups and fondue When using fresh ingredients remember that the speed of
7. your blends stay frozen To use the Frozen Treats cycle load your jar as indicated in the recipe you are using secure the lid and press the Frozen Treats icon The blender will run the cycle and automatically shut off After creating your frozen dessert serve immediately and store leftovers in the freezer WHOLE JUICE This cycle is designed to completely blend tough and dense ingredients including carrots celery and seeds Use the Whole Juice cycle if you are using any fruits and or vegetables with stems seeds or skins When blending carrot juice or other dense juices you may need to repeat this cycle once or twice until the desired texture and consistency are achieved HOT SOUP This cycle is designed for hot recipes The cycle s length of time combined with the speed of the motor heats the ingredients to a hot temperature This cycle can also be used for hot chocolate syrups and fondue When using fresh ingredients remember that the speed of the blade generates enough heat to warm the ingredients Do not add any liquids or ingredients over 115 F to the jar when preparing soups or hot items J PULSE Use Pulse for chopping mincing whipping or other tasks that do not require a long blend cycle You can also Pulse to quickly stir a blend before serving The Pulse setting runs at speed 7 and will only run while the Pulse icon remains pressed When the icon is released the motor shuts off CAP
8. ACITIVE TOUCH SLIDER The capacitive touch slider allows you to fine tune the speed of your blender Simply slide your finger to the right to increase the blenders speed or the left to decrease speed MODE Press Mode to switch between using the manual touch slider and the preprogrammed blend cycles SECTION 5 CARE AND CLEANING 5 1 CLEANING 1 Add 1 cup 240ml of hot water and a drop of liquid dish soap to the blender jar 2 Place the lid tightly onto the jar 3 Place the blender jar on the blender base and with your hand placed on top of the lid press the Pulse button for 5 seconds 4 Rinse well 5 Clean the base by simply wiping the base and interface with a damp cloth 5 2 LONG TERM SANITATION 1 For long term sanitation fill the blender jar with hot water 2 Add one to two teaspoons 5 10ml of liquid chlorine bleach to the jar 3 Stir for 10 seconds to mix water and bleach Let mixture stand in blender jar for five minutes 4 Empty water bleach mixture Turn jar upside down on dish rack until dry 5 3 CLEANING TIPS AND CAUTIONS Do not use stiff bristled brushes or abrasive cloths pads to clean the blender base or jar as this will dull or scratch the surface EVER submerge the blender motor in water Avoid submerging blender jars for more than 5 minutes Water penetration through the lower jar seals will reduce he life of the jar After cleaning we recommend the blender jar be stored upright BLENDER JA
9. AH 84058 U S A OF K TEC INC a 1 800 BLENDTEC OWN RD 214 MANUAL OWNERS PROSERIES BLENDTEC COM ALL MODELS ENG REV A OCTOBER 2014
10. DAMAGED If the blender malfunctions call your service agent first If it is dropped or damaged in any way return the blender to a Blendtec service agent immediately for examination repair electrical or mechanical adjustment or possible replacement 1 3 NEVER OPERATE BLENDER IN LIQUID To protect against the risk of electrical shock do not put the motor base in water or other liquid Do not use the blender outdoors where it is subject to precipitation 1 4 NEVER PUT NON FOOD ITEMS INTO JAR Utensils rocks and glass are dangerous if placed in jar Damage caused by such foreign objects will void the warranty Keep hands and utensils out of jar while blending to reduce the risk of severe injury to persons or damage to the blender Utensils may only be used when the blender is not running 1 5 NEVER OPERATE THE BLENDER WITHOUT THE LID IN PLACE 1 6 NEVER OPERATE THE BLENDER USING ATTACHMENTS NOT SOLD BY BLENDTEC The use of any unauthorized attachments may cause fire electric shock and or injury and will void the warranty 1 7 BLENDER JAR MUST BE PROPERLY IN PLACE WHILE APPLIANCE IS OPERATING 1 8 WARNING DO NOT BLEND HOT LIQUIDS OR OTHER HOT INGREDIENTS Starting blend cycles with boiling or very hot liquids may result in burns or cause the lid to blow off 1 9 USE CAUTION WHEN BLENDING ON THE HOT SOUP CYCLE When blending on the Hot Soup cycle friction of the blade will heat the contents The lid will allow pressure relief
11. If a jar is excessively noisy or if the blade assembly seems loose or sounds by hand contact your Blend 6 4 BLENDED TEXTURE UNSATISFACTORY f the blended texture of product is lumpy or uneven do the following Ensure the mixture is no 00 solid The blender b corrected by increasing iquid and or ensuring th colder than 10 degrees f the drink is mixing we increase cycle time Try he required extra blend TRIED EVERYTHING If non Blendtec service agent date of purchase bu alo ing or f ade th ng ec service center cavitating during the cycle Cavitation is a condition which an air pocket forms within the drink mix because the mix is too cold or en spins freely in this cavi he mix temperature by either re at the Fahren rozen ingredients used in has not had enough time f er cycle or touch and ho im urt e heit 12 degrees Celsius or complete blending gravelly when turned n ty This problem can be ducing ice increasing the recipe are never d the Pulse button for e of the preceding suggesti her assistance ons work contact your INSTRUCTIONS THAT APPEAR IN THIS USER GUIDE ARE NOT MEANT TO COVER EVERY POSSIBLE CONDITION OR SITUATION THAT MAY OCCUR GOOD JUDGMENT MUST BE USED WHEN OPERATING THIS OR ANY OTHER MACHINERY SECTION 7 WARRANTY WARRANTY DESCRIPTION The motor base and jar assembly including all n against leaking
12. R IS DISHWASHER SAFE TOP RACK ONLY Extreme temperatures damage the lower seal of the jar We recommend hand washing to prolong the life of the blender jar We do not recommend the jar be used for temperatures above boiling 212 F 100 C SECTION 6 TROUBLESHOOTING 6 1 While we don t expect you to have any problems with your blender sometimes failures do occur Use the following guidelines to see if the problem is easily fixed or requires service BLENDER MOTOR WILL NOT TURN ON NO POWER If the blender motor will not turn on try the following Determine if the blender is receiving power by checking for the green light on he Professional 750 or a wvhite power icon on the Professional 800 ake sure the blender is plugged in Check your house circuit breaker switch or fuse to make sure it is set to the ON position Press the Power switch or Power icon as applicable on the machine Unplug the power cord from the wall receptacle wait 5 seconds then plug power cord back in 6 2 ERROR MESSAGES ON DISPLAY 14 PROFESSIONAL 750 The OVERTEMP error message indicates an overheated condition has been detected and the motor has been disabled until the unit cools to operating temperatures Allow to cool for at least 20 minutes The OVERLOAD error message indicates too heavy of a load on the motor This is usually caused by a blockage in the jar preventing the blender blades from turning Remo
13. ROFESSIONAL D 5 blendtec OWNER S MANUAL AND USER GUIDE TABLE OF CONTENTS SECTION 1 IMPORTANT SAFEGUARDS o 2 SECTION 2 UNPACRINE 4 SECTION 3 GETTING TO KNOW YOUR BLENDER 4 SECTION 4 INSTALLATION amp OPERATIONAL OVERVIEW 5 4 1 PROFESSIONAL 750 Lua 5 4 2 PROFESSIONAL 800 times 10 SECTION 5 CARE AND CLEANING nn 13 SECTION 6 TROUBLESHOOTING nn 14 SECTION 7 WARRANTY sensor arersnensnnsnnenan nan aena 16 SECTION 1 IMPORTANT SAFEGUARDS IMPORTANT INFORMATION Read all instructions carefully before using your Blendtec blender Following these instructions will help prevent injuries and damage to the machine and will ensure that you have the best possible experience with your new blender 1 1 AVOID CONTACT WITH MOVING PARTS ALWAYS keep fingers hands hair and clothing away from all moving parts ALWAYS keep all utensils away from the drive socket and blender jar blades during operation as utensils may damage blades or the blender jar EVER put hands into the blender jar or add substances by hand when the blender jar is on the motor base EVER touch the blade with your fingers whether it is on or off the motor base EVER place jar into drive socket if blender motor is operating DO NOT rock or remove the blender jar during operation These precautions will prevent personal injury and or damage to the blender 1 2 NEVER OPERATE THE BLENDER IF IT APPEARS
14. RPOSES VOIDS ALL WARRANTIES 1 16 NEVER OPERATE THE BLENDER WITH MORE THAN THE MARKED CAPACITY OF THE JAR SAVE THESE INSTRUCTIONS SECTION 2 UNPACKING SAVE ALL PACKAGING MATERIALS AND INSTRUCTIONS FOR FUTURE USE 2 1 UNPACKING YOUR BLENDER You should have received the following items Professional series blender motor base Blender jar with lid Additional literature may be included depending on package configuration 1 Remove blender motor base blender jar and lid from packaging 2 Unwind the power cord 3 Check for any packing material that may have blocked ventilation holes on the underside of the blender motor base 4 Inspect all items to ensure no damage occurred during shipment f any damage has occurred contact Blendtec customer service See page 17 immediately 2 2 RECORDING YOUR SERIAL NUMBER AND DATE OF PURCHASE Record your blender motor serial number and date of purchase in the space below You will need these when contacting Blendtec for service or questions Motor Serial Found on bottom of motor base Date of Purchase Purchased From 2 3 REGISTERING YOUR BLENDER Register online at www blendtec com registration oO SECTION 3 GETTING TO KNOW YOUR BLENDER Refer to Figures 1 and 2 on Page 6 3 1 BLENDER MOTOR BASE Smart Touch Interface The interface consists of one touch pre programmed ee and speeds as well as Stop and Pulse buttons Hardened Metal Drive Socket T
15. his is where the jar couples with the motor to turn he blade assembly It is made of hardened metal LCD Information Center This displays how many blend cycles your blender has run remaining time during blends and any error messages Power Unit This unit is located within the blender motor base and contains the computerized electronics that run the blender otor Base Cover This durable plastic material houses the power unit Power Cord The power cord is located at the back of the motor base cover 3 2 BLENDER JAR ASSEMBLY The blender jar assembly consists of the blender jar blade assembly and lid Jar The jar is durable BPA free and easy to clean Blade Assembly The uniquely designed stainless steel blade provides fast consistent blending Lid The lid seals liquids within the jar during blending NOTE Filling the blender jar beyond the marked capacity is not recommended SECTION 4 INSTALLATION amp OPERATIONAL OVERVIEW 4 1 PROFESSIONAL 750 4 1 1 INSTALLATION Above Counter Installation 1 Place the blender on a flat clean and dry surface Blender vents should be unobstructed to allow proper cooling during use 2 Make sure an outlet is available within two feet of the blender motor 3 Place appropriately filled blender jar with lid in place onto blender base 4 We recommend that surge protection be placed between the receptacle and he blender motor on the circuit connected to the blender m
16. or breakage for the warranty peri noving jar parts are covered od Warranties begin from Cosmetic damage product abuse unreasonable use damage resulting from an accident including fire flood earthquake or oth er natural disasters product tampering use of accessories not endorsed by Blendtec service performed or Limited Warranty Blendtec warrants the blender motor to be free of defect in material and workmanship for the warranty period During this period such defects will be repaired or the product replaced at Blendtec s discretion without charge This warranty does not cover damage caused by misuse accident or negli gence All implied warranties including but not limited to implied warranties of fitness and merchantability are limited in duration to the warranty period on motor and jar Any unit Submitted for repair must be accompanied by proof of original purchase For repairs under warranty Blendtec will provide prepaid shipping For repairs out of warranty shipping must be arranged and paid for by the customer Send all units for repair to blendtec 1206 South 1680 West Orem UT 84058 1 800 BLENDTEC 801 222 0888 For International toll free service please contact Australia 1 800 014098 Canada 855 230 0888 France 0 800 910346 Japan 0066 33 821731 Mexico 001 855 230 0888 South Korea 003 081 32941 Spain 900 948733 Taiwan 008 01147146 United Kingdom 0800 1510183 The above limita
17. otor Preparation for In Counter Installation 1 Identify the best place to install your blender Consider proximity to ingredients available counter space and access to a power outlet 2 Ensure that the location meets all dimensional requirements see Figure 3 a The countertop must be no thicker than 1 1 4 inch 32 mm to ensure adequate ventilation NOTE Ensure sufficient air circulation beneath the blender base Hot air should not be trapped beneath the counter top Nothing should be stored within 3 inches 76 mm of the bottom of the motor 3 Cut a hole in the counter top 4 inches 111 mm wide and 5 inches 149 mm long with the shorter side facing the operator See Countertop Hole Template or Figure 3 Make sure all space requirements and measurements are correct BEFORE cutting It is recommended that you consult with a professional before cutting In Counter Installation 1 Remove the motor base from the motor base cover 2 Slide the blender base into the new hole in your countertop the LCD indicator and touchpad facing the operator side of the blender The rubber gasket on the rim of the motor base should fit into the hole and rest lightly on the countertop 3 Make sure the power switch is off Plug the unit into a 120 volt outlet with 15 amp protection FIGURE 1 BLENDER JAR ASSEMBLY Clear Vented Cap Insert Lid Jar Blade Assembly FIGURE 2 MOTOR
18. s fondues Pulse stir chop or mince at a high speed BATTERS This cycle stays at relatively low speeds for shorter periods of time This combines your batters or dips allowing the flavors to blend together properly without over mixing To use the Batters cycle load your jar as indicated in the recipe you are using secure the lid and press the Batters icon The blender will run the cycle and automatically shut off MIXED DRINKS This cycle is used for mixed drinks iced coffees and milkshakes The length of time creates a consistency that is ideal for these types of recipes o use the Mixed Drinks cycle load your jar as indicated in the recipe you are using secure the lid and press the Mixed Drinks icon SMOOTHIE This cycle is designed specifically for various types of smoothies and thick drinks that frequently use dense or frozen ingredients It slows down and speeds up automatically during the course of the cycle This allows the blender to draw the ingredients into the blending vortex creating the desired texture To use the Smoothie cycle load your jar as indicated in the recipe you are using secure the lid and press the Smoothie icon The blender will run the cycle and automatically shut off FROZEN TREATS This cycle is designed specifically for frozen treats including ice cream sorbets and frozen yogurt The cycle speeds up and slows down at the appropriate moments to ensure
19. tion Center Your Purchase Date Place of Purchase An explanation of the problem 18 OUT OF WARRANTY 1 Contact Blendtec to diagnose the difficulty Please have the blender serial number ready along with a description of the problem Do not attempt to do your own repairs Many issues can be resolved simply and quickly over the phone 2 Ifthe blender is not under warranty and you wish to have it repaired please call customer service with your serial number place of purchase and date of purchase so we may give you further instructions on how to send your machine in for an out of warranty repair 3 When you ship your unit please enclose the following Your Name Address Phone Number Motor Serial Found on bottom of motor base Cycle Count From the LED Information Center Your Purchase Date Place of Purchase An explanation of the problem Notice to Australian Customers Our goods come with guarantees that cannot be excluded under the Australian Consumer Law You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure 19 1206 SOUTH 1680 WEST 2014 K TEC INC ALL RIGHTS RESERVED BLENDTEC IS A REGISTERED TRADEMARK OREM UT
20. tions may not apply in states where limited warranties are not allowed Other warranties may apply outside of the USA and Canada Using a machine outside the country it was designed for will void the warranty attempted by have been or unauthorized service agencies units that have modifications or used for commercial purposes are n The quality of ot included under this warranty Blendtec blenders is unsurpassed You will enjoy years of wondertul and reliable service from your Blendtec Professional series blender THIS WARRANTY APPLIES ONLY TO PRODUCTS SOLD BY BLENDTEC OR ITS AUTHORIZED DEALERS 16 UNDER WARRANTY 1 Contact Blendtec immediately to diagnose the difficulty Please have the blender serial number ready as well as a description of the problem Do not attempt to do your own repairs Repairs made by persons other than Blendtec authorized service representatives will void the warranty Many issues can be resolved simply and quickly over the phone 2 If the difficulty cannot be resolved over the phone your unit may require replacement If blender is under warranty Blendtec will repair or replace the unit at no cost Cosmetic damage and abuse are not included 3 Upon receiving instructions from Blendtec box up your existing unit and enclose the following Your Name Address Phone Number Motor Serial Found on bottom of motor base Cycle Count From the LED Informa
21. ued use may cause permanent damage to the motor Overload Error There is an overload on the motor Check the blender jar for blockage and clear if necessary Press Cancel to clear the overload message If overload condition re occurs contact Blendtec customer service see page 17 Reset Errors If the following error messages appear reset the error by pressing he cancel button or cycle the power by unplugging your blender and then plug ging it back in If the error does not clear contact your Blendtec service agent Error Overtemp condition detected Error Overload condition detected Error Temp sensor not detected Error Zero crossing not detected Error Reset error detected Error Read Write error detected Error Motor control error detected Error Invalid blend cycle Error Touch controller not detected Error Touch controller output is invalid 15 Blender Motor Remove the ja 6 3 NOISE LEVEL CHANGES If the blender noise level has increased from original the sound is coming from the blender motor or jar r and press Pulse Listen levels determine whether to the motor If it is excessively noisy please contact your Blendtec Service Agent for evaluation Jar After checking the motor place the jar back on the for a few seconds using the motor Run the motor Pulse button If you have more than one jar test a different jar to determine whether the sound is different
22. ve the jar from the blender to clear any blockage then return the jar to the blender base Use PULSE to quickly pulse the blade through the mixture Once the blade spins freely a programmed button may be used If blender fails to start after following these steps contact your Blendtec service center for assistance A RESET error indicates a disruption in the normal operation of the electronic blender controls This is an uncommon error message which is usually caused by incoming power fluctuations or spikes This error message is cleared by turn ing off the blender for ten seconds using the switch then turning back on If this error is displayed immediately on start up or if it occurs regularly during normal use contact your Blendtec service center for assistance BLADE STOPS If the overload switch stops the blender remove the blender jar and carefully check for blockage of the blade If no blockage is found replace jar and use the Pulse button on the touch pad to quickly pulse the blade through the mixture Once the blade spins freely a programmed button may be used PROFESSIONAL 800 Touch Error This occurs when the side or space next to a control surface button was touched To avoid this message touch the center of the desired button Overtemp Error The motor is overheating The blender has been disabled until the unit cools to operating temperatures Allow it to cool for at least 20 minutes Contin
Download Pdf Manuals
Related Search