TEL-17P+TEL-19P
Contents
1. 5 Picture Sound EJ PIP baa Display Fal Function XT Exit H Position Use to change horizontal position of the picture You may press 4 or v key to select H Position and press 4 key to increase Blue bar to shift the picture to right or press v to decrease Blue bar to shift the picture to left V Position Use to change vertical position of the picture You may press 4 or v key to select V Position and press 4 key to increase Blue bar to shift the picture up or press V to decrease Blue bar to shift the picture down Image Ratio PC Mode In order to meet different applications in video output there are 2 image ratio to choose 1 4 3 2 16 9 Press 4 or v key to select the ratio you want 1 4 3 The image fully fills up the 4 3 screen on both Vertical and Horizontal lines B 13 Image Optimize LA T Phase Clock WW Auto Adjust oc 2 16 9 This mode to make the format as 16 9 to support the 7 WE 16 9 signal input from PC ley ee e 16 18 Image Optimize Select the Image Optimize for best image setting Press Menu to enter OK mode To select the Auto Color The monitor will auto fine tune the color as default Phase Use phase to fine tune the monitor to perfectly ADC clock phase synchronize to the video signal source under RGB mode Press 4 or v to i2. If a new plug is to be fitted please observe the wiring code as shown below In case of doubt please consult a qualified electrician WARNING This appliance must be earthed grounded IMPORTANT The wires in this mains lead are colored in accordance with the following codes lil e Green and Yellow Ground Earth e Blue Neutral e Brown Live If the colored wires of the mains lead of this appliance do not correspond with the colored markings identifving the terminals in vour plug proceed as follows The wire which is colored GREEN AND VELLOW must be connected to the terminal in the plug which is marked by the letter E or by the Earth symbol or colored GREEN or GREEN AND YELLOW The wire which is colored BLUE must be connected to the terminal in the plug which is marked with the letter N or colored BLACK The wire which is colored BROWN must be connected to the terminal in the plug which is marked with the letter L or colored RED If you have any questions concerning the proper power cord to use please consult the dealer from whom you purchased the product 3 Standards and Guidelines 3 1 FCC Requirements This device complies with Part 15 of the FOC Rules and Regulations Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must tolerate any interference encountered including interference that may cause improper operation The eq
3. 4 or v key to select OSD Time and press Enter key to adjust the time it can be adjusted from 5 second to 60 second OSD Blend If you want to change the background color of OSD Menu you may press 4 or v key to select Background color Press Enter key and press 4 or v key to increase decrease the Blue bar the color will change from light blue to dark blue Sleep Time The function will make the monitor in sleep mode to save the power when monitor is in standby mode To press Enter to enter the option and press 4 or v key again to select 1 10 Min 2 20 Min 3 30 Min 4 60 Min 5 90 Min 6 120 Min 7 150 8 180 9 Off To select 10 Min that means the monitor will enter sleep mode when monitor is in standby mode for more than 10 Min The other time options are the same rule Anti Burn in The function can prevent the LCD panel from burn in when camera or DVR is always displaying the same picture source at all times Press 4 or v key to select Anti Burn in and press Enter to enter the option and press 4 or v key again to select 1 30 Min 2 60 Min 3 90 Min 4 120 Min 5 150 Min 6 Off To select 30 Min the image will move left for one pixel for every 30 minutes to select 60 Min the image will move left for one pixel for every 60 minutes the other options are the same regulation ID
4. The ID function is only applicable for some specific models if the model you brought has the ID function Please check the ID setup procedure Default If you want to back to factory default press 4 or v key to select Default and press Enter key to activate OK Exit Press the Menu key and press 4 or v to select Exit to exit the OSD menu MI Picture s Sound EJ pip kd Display F gt Function MI Exit 16 Picture PC Mode Menu 1 Press the Menu key on the buttons to call out the Brightness OSD Menu Press 4 or v to select Contrast Picture Mode and press Menu key again to select the Picture option Backlight AA OK 2 Various picture settings are available from the Picture rer sabi menu Use 4 or v to select item that you want to adjust and press Menu key again until grey bar changes to blue color and press 4 or v CETE ET PIP fiw Display F Function MIT Exit increase or decrease the figure that you wish Press Exit key to return to menu and confirm the setting Press two times of Exit to exit the menu Brightness Press a or v to increase decrease the Blue bar to adjust brightness Adjusting brightness to enhance the level of dark area in the video picture such as night scenes and shadow scenes Increasing brightness will make dark areas more vi
5. Check if the LCD Monitor power switch is at the on position and the LED on the front of LCD Monitor is in still green Check if the computer or AV equipment video signal cables are properly secured Abnormal image Check and make sure the computer or AV equipment video signal cables are properly and securely connected to the sockets on back of the LCD Monitor Abnormal image colors on the Check and make sure the LCD Monitor video signal cables are properly screen and securely connected to the VGA BNC RCA sockets on back of the computer Please refer to Chapter Function to check if there is any improper screen adjustment or setting Please make sure both video inputs are properly connected BNC RCA image on the screen S Video and VGA Can only see video but no Please make sure both audio inputs are properly connected the audio audio input plugs are RCA and 3 5mm audio line in Check if the volume is at the lowest level 20 9 Applicable Video Timing for PC analog Video The following table list are the better display quality modes for analogy signal PC supported by this LCD monitor The LCD monitor will stop working or has poor picture quality when other modes out of below list input D sub Mode timing Horizontal Vertical gt Nominal Nominal Nominal Frequency Frequency Pixel 0 5 KHz 1 Hz Clock MHz VGA 640 350 70Hz 31 469 70087 gt SXGA_ 1280 1024 70Hz 74882 698
6. EE OO SA DC12V RCA RCA PC Audio VGA S Video BNCAn BNC Out AudioR Audio L O DC 12V Input Please use DC 12V 3A Power Adaptor Stereo RCA Audio Input Stereo audio input R is right channel Red of audio connector L R L is the left channel White of the audio of connector PC Audio Input 3 5mm Connect to the audio output of your computer D Sub VGA Input Connect to the VGA output of your computer or DVR Connect the S Video 4 pin DIN connector from the DVR or AV S Video Input equipment to the Monitor DEG This Video input and output are used for CVBS input and output Composite Video Input and Output BNC type Thismonitor also supports the auto looping function permitting the connection of another monitor from the output connector 11 6 OSD Setup Picture Video Mode Menu 1 Press the Menu key on the buttons to call out the Brightness OSD Menu Press 4 or v to select ne Picture mode and press Menu key again to select Sharpness the Picture option Tint Saturation 2 Various picture settings are available from the Picture Color Temp menu Use 4 or v to select item that you want to adjust and press Menu key again until grey bar changes to blue color and press 4 or v Pitre Sound EJ pip E Display Fol Function ll Exit increase or decrease the figure that you wish Press Exit key to return to menu a
7. the original cord set or if the cord set is not enclosed The female receptacle of the cord set must meet IEC 60320 requirements and may look like this Figure A1 below ea Figure A1 Figure A2 2 3 1 For the United States and Canada In the United States and Canada the male plug is a NEMA5 15 style Figure A2 above UL Listed and CSA Labeled For units which are mounted on a desk or table SVT or SJT type cord sets may be used For units which sit on the floor only SJT type cord sets may be used The cord set must be selected according to the current rating for your unit Please consult the table below for the selection criteria for power cords used in the United States and Canada Code Type Size of Conductors in Cord Maximum Current Rating of Unit SJT 18 AWG 10 Amps 16 AWG 12 Amps 14 AWG 12 Amps 18 AWG 10 Amps 17 AWG 12 Amps 2 3 2 For European Countries In Europe you must use a cord set which is appropriate for the receptacles in your country The cord set is HAR Certified and a special mark that will appear on the outer sheath or on the insulation of one of the inner conductors 2 3 3 For the United Kingdom For your safety please read the following text carefully If the fitted molded plug is unsuitable for the socket outlet then the plug should be cut off and disposed of Safely j DANGER Do not plug the cut off plug into a socket outlet There is a danger of severe electrical shock
8. 838 gt Mode Resolution 19 21 10 Technical Data odel IEL T P TEL 19P Composite signal 0 6 1Vpp 75 ohm Y 1Vp p C 0 3Vp p Scan Frequenc H 31K 81KHz V 56 75Hz peration Interfaces ront Panel Controls POWER SOURCE EXIT MENU ENTER LED Power on Green Standby Orange OSD No Signal Source SD Control Yes SD Language English German French Spanish Italian Chinese 6 nput Output Connector VGAx1 S Video x 1 PC Audio Input 3 5 Jack x 1 RCA Audio x 2 R L Video Input BNC Jack x 1 Power Input DC 12V 3A x 1 echanical amp Electrical Design 5 C 40 C 20 85 RH ccessor Specifications and product design are subject to change without notice 2 O a mt O Ti O 2 22 11 Dimension TEL 17P 47 mm 374 mm 374 mm AO 318 mim 368 mm TEL 19P 412 mm 47 mm 412 mm LILU DO AAC In II 347mm 403mm 210 mm 21 23
9. CCTV LCD Monitor User Manual For models TEL 17P TEL 19P y A English Contents i JIMPFOGUCHOM ti tA A A A i ta kai dat 1 Ze MWork satelv informatio tii ii i i i a Ai nia L 2 Zola POdUe Saler Precautions NOMEN idas use ia sea we a dada aa e 2 A O a G 3 2 3 Important Notice Concerning Power Cord SelectiON ooonccconnnccconncncononcnnnnnnanononnanonnnnancnonnncnnnnnronnonanennnnnns 3 231 iFor dhe United States and CANE vedde ard 3 2 32 For European CounieSuuaaurssasrdees n eee 3 2 33 For fe United Kingdom asa ii a i A 4 3 Standards nd Guidelines ee 5 Sale FOG Bee Sii a ia E 5 32 FOO VANN NT 5 5 LE GONE 5 3 4 ROHS Compliance State Mei ii amnesi 6 3 5 Information on Disposal for Your Old PrOdUCt oocnccocnccnnnccccconccncncnnncnnnncncnncncnncnnnnnnnnnnnnnnnrnnrnnonnnronarenannnonenenos 6 Ay Hardware Instala ON naaa AS 7 4 1 Checking the Accessories Supplied occccoccccocncccncccoonconnnononcnnononnncnnnnnnonnnnnnnnnnnrnnnnnnnnnrnnnnrnnnnnnrnnnnrnnnrinnnnenass 7 5 BUNONS and CoOnneclons dica 8 Dell JDUQ Sas tcc lore edd ioe a SR 8 52 COME HPS 9 6 OSD SetuP Re 10 7 Troubleshooting Guides 18 8 Applicable Video Timing for PC analog Video ocooococccocccocccoccnonononnnconnconnca nc nncanannnnnos 19 SO Technical Dala vade 20 10 Dimension sa 21 1 Introduction Thank you for purchasing the professional CCTV LCD Monitor and welcome to a fantastic new technology t
10. Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations 3 2 FCC Warning To ensure continued FCC compliance the user must use a grounded power supply cord and the shielded video interface cord with bonded ferrite cores provided If a BNC cable is going to be used use only a shielded BNC 5 cable Also any unauthorized changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this device 3 3 CE Conformity 2004 108 EC with regard to Electromagnetic compatibility and The device complies with the requirements of the directive 206 95 EC with regard to Safety 3 4 RoHS Compliance Statement This display defined in this user manual is 100 RoHS complaint and meets all the requirements set forth in European Union Directive 2002 95 EC Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment 3 5 Information on Disposal for Your Old Product Used electrical and electronic equipment must be treated separately and in accordance with legislation that requires proper treatment recovery and recycling of used electrical and electronic equipment When this corssed out wheeled bin symbol is attached to a product it means the product is covered by the European Directive 2002 979 EG If you wish to discard of this product please contact your local authorities and as
11. an be serviced by users Refer servicing to qualified personnel TO PREVENT FIRE OR SHOCK HAZARD DO NOT EXPOSE THIS CCTV LCD MONITOR TO RAIN OR MOISTURE WARNING HIGH VOLTAGE EXISTS ON THE BACK LIGHT POWER LEAD OF THIS CCTV LCD MONITOR BEFORE SERVICING DETERMINE THE PRESENCE OF HIGH VOLTAGE BY CONNECTING THE H V METER BETWEEN THE BACK LIGHT POWER LEAD AND CHASSIS ONLY 2 1 Product Safety Precautions Follow all warnings and instructions marked on the product 1 Do not use this product near water 2 This LCD monitor should be installed on a stable horizontal base 3 When cleaning use only a neutral detergent cleaner with a soft damp cloth Do not spray with liquid or aerosol cleaners 4 Do not expose this LCD monitor to direct sunlight or heat Hot air may cause damage to the cabinet and other parts 5 Adequate ventilation must be maintained to ensure reliable and continued operation and to protect the LCD monitor from overheating Do not block ventilation slots and openings with objects or install the LCD monitor in a place where ventilation may be obstructed 6 Do not install this LCD monitor near a motor or transformer where strong magnetism is generated Images on the LCD monitor will be distorted and the color irregular 7 Do not allow metal pieces or objects of any kind fall into the LCD monitor through ventilation holes 8 Do not attempt to service this unit yourself Removal of the LCD monitor cover m
12. ay expose you to dangerous voltage or other hazards Refer all servicing to qualified service personnel 9 Unplug this product from the wall outlet and refer servicing to qualified service personnel in the event that Liquid is spilled onto the product or the product is exposed to rain or water The product does not operate normally when the operating instructions are followed The product has been dropped or the cabinet has been damaged The product exhibits a distinct change in performance indicating a need for service The power cord or plug is frayed or damaged Has referred to Troubleshooting Tips and problems still can t be solved 2 2 Safety Guidelines WARNING This device must be operated with the original power supply CAUTION The socket outlet should be installed near the equipment and should be easily accessible Use a power cord that is properly grounded Always use the appropriate AC power cord that is certified for the individual country Some examples are listed below N CAUTION USA UL Switzerland SEV Canada CSA Britain BASE BS Germany DE Japa eee Electric Appliance Control Act 2 3 Important Notice Concerning Power Cord Selection The power cord set for this unit has been enclosed and has been selected according to the country of destination It must be used to prevent electric shock Use the following guidelines if it is necessary to replace
13. e a Sound PIP kia Display Fl Function XT Exit H Position Use to change horizontal position of the picture You may press 4 or v key to select H Position and press 4 key to increase Blue bar to shift the picture to right or press v to decrease Blue bar to shift the picture to left V Position Use to change vertical position of the picture You may press 4 or v key to select V Position and press 4 key to increase Blue bar to shift the picture up or press V to decrease Blue bar to shift the picture down Image Ratio Video HDMI mode In order to meet different applications in video output there are 5 image ratio to choose 1 5 4 Full 2 4 3 Under V 3 4 3 Over H 4 5 4 Over 1 5 5 4 Over 2 Press 4 or v key to select the format ratio you want 1 5 4 Full The image fully fills up the screen on both Vertical and Horizontal lines To enlarge the 4 3 video source to 5 4 panel format 2 4 3 Under V The format is the Letter Box under scan mode that shows the real 4 3 video source on 5 4 panel format without distortion That will create a black bar on top and bottom of 5 4 panel format 12 14 3 4 3 Over H The format is the Pan Scan over scan mode that shows the real 4 3 video source on 5 4 panel format Fo without distortion In order to erase the black bar on EIT both top and bottom cu
14. easing color figure will make the color more intense Reducing color figure will make the color less intense Color Temp Select the Color Temp for white balance Press Menu to enter OK mode There are six settings to choose from 1 Standard 2 Cold 3 Warm 4 User To select User you may press 4 or v to increase decrease the Blue bar to adjust color of Red Green and Blue 10 12 Sound Video Mode Menu 1 Press the Menu key on the buttons to call out the OSD Sound Mode Menu Press 4 or v to select Sound option eee and press Menu key again to select the Sound mode Balance There are 2 sound modes to choose from 1 Standard Speaker Enhance 2 User 2 To select User you may press 4 or v to select item that you want to adjust m Picture sf Sound PIP kad Display 5 Function INI Exit Bass Press 4 or v to increase decrease the Blue bar to enhance the bass or reduce the bass Treble Press 4 or v to increase decrease the Blue bar to increase the treble or reduce the treble Balance Press 4 or v to increase decrease the Blue bar to enhance right speaker or enhance the left speaker Put the figure on O will keep the balance of right speaker and left speaker Speaker Enhance Press 4 or v to switch On or switch Off the soeaker e
15. hat will completely change the way you look at monitors The following sections describe just a few of the major advantages of this LCD monitor You ll discover more of its wonderful features as you use tt Please note that this manual is used with many similar monitor models Please check the model number on the carton and on the back of the unit to make sure if the user manual is applicable to your machine 1 The LCD monitor is used in the same way as the CRT monitor There is no need to change the hardware of your computer just plug it in and it is ready for use 2 The monitor will accept and display analog video NTSC or PAL PC type video and Digital video SOUICES 3 Low radiation and reduced flickering compared to traditional CRT monitors that minimizes eyestrain and health hazards 4 The compact size makes transportation easier and allows to use in many applications 5 This LCD monitor can support PC VGA Composite S Video signals 6 The composite video input ports accept different signal sources e g Camera DVR etc 7 The design allows VESA wall mounting installation 8 This monitor includes special functions for 3D comb filter De interlace Anti burn in mode auto impedance switch for looping video connection 2 Work Safety Information Caution and Warning CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION To reduce the risk of electric shock do not remove cover or back No internal parts c
16. k the correct method of disposal A The coorect disposal of your old product will help prevent potenital negative consequences for the environment and human health Attention if you want to dispose of this equipment please do not use this ordinary dust bin 4 Hardware This chapter will guide you through the correct installation procedures for the LCD monitor 4 1 Checking the Accessories Supplied LCD monitor body Desk Stand x 1 pc AC power cord x 1 pc Adaptor x 1 pc VGA 15 pin cable 1 8 Meter x 1 pc 3 5mm audio line 1 5 Meter x 1 pc User manual CD x 1 pc 5 Buttons and Connections 5 1 Buttons 1 Power Press button to turn the power on and press again to turn the power off Source Exit e O HA e O ae OQ Menu Enter 2 Source Exit 1 To select the input signal source when the OSD menu is Off The available signal source will be shown in the following order PC HDMI AV1 AV2 S Video 2 To exit the menu when you finish the setting A Up Increase To move the cursor upwards or to switch over the setting items or to increase the figure of the setting selected wW Down Decrease To move the cursor downwards or to switch over the setting items or to decrease the figure of the setting selected 5 Menu Enter To Enter the OSD menu or confirm the setting 10 5 2 Connections CD ad 4 5 C6 G B
17. ncrease decrease the Blue bar to adjust the Phase Clock Use Clock to fine tune the monitor when phase value is wrong Press 4 or v to increase decrease the Blue bar to adjust the Clock Auto Adjust Use Auto Adjust to fine tune the display to perfectly synchronize to the video signal source under RGB mode Press Menu to enter OK mode to activate the Auto Adjust function Function PC Mode OSD Time OSD Blend Sleep Time The setup is the same as page 13 for Function adjustment of Video Mode ID OK Default OK m Picture sf Sound 22 PIP kal Display ES Function IT Exit Exit Press the Menu key and press 4 or v to select Exit to exit the OSD menu mu Picture af Sound m PIP kal Display F Function KKM Exit 17 19 8 Troubleshooting Guide When you experience issues with the CCTV LCD Monitor before contacting your retailer where you made your purchase please check the following items The most common issue Is with the connection of AV equipment or graphic card We recommend that at the same time of troubleshooting also refer to the AV equipment or graphic card user manual Please do not use a higher refresh rate than the maximum specified by the CCTV LCD Monitor No image appears onthe LCD Check if the computer or AV equipment power cord is securely connected Monitor screen to the wall socket or to the extension cord
18. nd confirm the setting Press two times of Exit to exit all the menu Brightness Press a or v to increase decrease the Blue bar to adjust brightness Adjusting brightness to enhance the level of dark area in the video picture such as night scenes and shadow scenes Increasing brightness will make dark areas more visible Contrast Press 4 or v to increase decrease the Blue bar to adjust contrast Increasing contrast will make white area of the video picture brighter Contrast works in conjunction with Brightness Backlight Press 4 or v to increase decrease the Blue bar to adjust backlight Increasing the figure will enhance the backlight Decreasing the figure will reduce backlight Sharpness Press 4 or v to increase decrease the Blue bar to adjust sharpness Using sharpness to adjust the detail enhancement to the video picture Increasing the figure will enhance the edges of objects in the video picture Decreasing the figure will reduce enhancement Tint Press 4 or v to increase decrease the Blue bar to adjust hue Using hue to adjust the color of flesh tones Increasing figure will make the picture with more red in appearance Decreasing figure will shift the picture with more green in appearance Saturation Press 4 or v to increase decrease the Blue bar to adjust color saturation Incr
19. nhancement Volmue Just press 4 or v to increase decrease the Blue bar to adjust volume when OSD Menu is Off mode PIP Video Mode Press the Menu key on the buttons to call out the OSD ke aske Menu Press 4 or v to select PIP mode ma a and press Menu key again to select the PIP option Sub Position Menu Picture af Sound PIP bid Display F3 Function MI Exit Sub Source Press the Menu key to enter the Sub Source and press 4 or v to select PC as the sub screen Sub Size Press the Menu key to enter the Sub Size and press 4 or v to select the size of sub screen There are 4 size to select 1 Small 2 Medium 3 Large 4 PBP or select Off to close PIP setting Swat Press 4 or v key to enter the Swat and press Enter to activate OK and swat the main screen and sub screen Sub Position Press the Menu key to enter the Sub Position and press 4 or v to select 0 4 as the position of sub screen 0 Top left 1 Bottom left 2 Central 3 Top right 4 Bottom right 11 13 Display Video Mode Menu Press the Menu key on the buttons to call out the OSD dna osition A Menu Press 4 or v to select Display mode Image Ratio 5 4 Over 1 and press Menu key again to select the Display option Image Optimize OK Pictur
20. sible Contrast Press 4 or v to increase decrease the Blue bar to adjust contrast Increasing contrast will make white area of the video picture brighter Contrast works in conjunction with Brightness Backlight Press 4 or v to increase decrease the Blue bar to adjust backlight Increasing the figure will enhance the backlight Decreasing the figure will reduce backlight Color Temp Select the Color Temp for white balance Press Menu to enter OK mode There are 4 settings to choose from 1 Standard 2 Cold 3 Warm 4 User To select User you may press 4 or v to increase decrease the Blue bar to adjust color of Red Green and Blue Sound PC Mode Menu The setup is the same as page No 11 for sound setup Sound Mode of Video Mode Bass Treble Balance Speaker Enhance m Picture sf Sound 2 PIP Es Display F Function KI Exit PIP PC Mode Menu Sub Source The setup is the same as page No 11 for PIP setup Sub Size of Video Mode ete lAcitinar SIHO fm Picture sf Sound PIP bE Display F2 Function XII Exit 15 17 Display PC Mode Menu Press the Menu key on the buttons to call out the er POSITION OSD Menu Press 4 or v to select Image Ratio Display mode and press Menu key again to Image Optimize Select the Display option Phase Clock Auto Adjust
21. t about 4 on Vertical line pr to fill up the screen IBFicue af Sound ET mr 1 V il W Lur 1 im 4 5 4 Over 1 The format is over scan mode to make the image fill up the screen and cut about 2 on Vertical and 4 on Horizontal lines 5 5 4 Over 2 The format is another over scan mode to make the image fill up the screen and cut about 3 on Vertical and 6 on Horizontal lines Image Optimize Select the Image Optimize for best image setting Press Menu to enter OK mode To select DNR Dynamic Noise Reduction the DNR will reduce the noise level and improve the video quality There are four levels to select 1 Low 2 Medium 3 High 4 Off Press 4 or v key to select the level Function Video Mode Press the Menu key on the buttons to call out the OSD OSD Time Menu Press 4 or v to select Function mode me and press Menu key again to select the Function option Anti Burn in ID Default fm Picture sf Sound 22 PIP kal Display E Function XI Exit 13 15 Language The default language is English you may press the Enter key and press 4 or v key to select language you want There are 6 languages to select 1 English 2 French 8 Germany 4 Spanish 5 Italian 6 Chinese OSD Time If you want the OSD Menu to stay longer on the screen you may press
22. uipment has been tested and found to comply with the requirements stipulated in Part 15 of FCC regulations for a Class B digital device These requirements are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in strict compliance with the instructions may disrupt radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause detrimental interference with radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by taking one or more of the following measures e Reorienting or relocating the receiving antenna e Increasing the separation between the equipment and the receiver e Connecting the equipment into an outlet on a circuit different from the one which the receiver is connected e Consulting the dealer or an experienced radio TV technician for help Shielded interconnected cables and shielded power cords must be used with this equipment to ensure compliance with the pertinent RFD emission limits governing this device Changes or modifications not expressly approved by the manufacturer could void the user s right to operate the equipment Notice of Compliance with Canadian Interference causing Equipment Regulations This
Download Pdf Manuals
Related Search