CD55HD user`s manual - COP
Contents
1. Figure 16 Figure 17 Figurel8 4 To ensure a smooth and successful installation you must Have electrical work comply with latest national electrical code national fire code and all applicable local codes and ordinances Coordinate work with other trades to avoid interference Verify existing site conditions and coordinate with owner s representative and appropriate utilities as required Obtain copies of all related plans specifications shop drawings and addenda to schedule and coordinate related work Thoroughly review the project to ensure that all work meets or exceeds the above requirements Bring alleged discrepancies to the attention of the CCTV Project Coordinator Technical data table Indoor Outdoor Speed Dome SSS 18 Operation Manual for Intelligent Speed Dome Camera Control mode RS485 Baud Rate 2400 4800 9600 19200 bps Fan amp heater Fan amp heater auto start only outdoor dome eae Indoor dome 5 C 45 C Outdoor dome 35 C 55 C 2 Camera Optional data table SD NTSC CROP NTSC SQUEEZE PAL CROP PAL SQUEEZE VI Troubleshooting Probable cause Power supply fault On power no action Bad connection of the power Transformer damaged On power cannot self check Mechanical failure have image but have motor noise Power supply not enough Video signal fault Seli check ok but have no Bad connection of the video Press to full connect Camera da2. Speed Dome Address 4 Speed Dome Address 18 Speed Dome Address 1023 Setup of the Protocol and the Default Baud Rate As shown in Figure 2 SW2 is used to set the protocol of communication and the baud rate used by the dome camera DIP 4 to DIP 1 of SW2 is used to select protocols and 16 different protocols can be selected in 12 Operation Manual for Intelligent Speed Dome Camera maximum Following table shows states of coding switches of protocols selected by the dome camera Table 2 Some protocols and the states of the coding switches of normal baud rate of these protocols are shown as follows 9600Bps gM ppg 9600 Ne ofan 2 3 4 2 3 4 5 5 PELCO P D 2400Bps 3 i 1 i d ALEC 9600Bps Y ON PELCO P D 4800Bps 2 3 PELCO MK 4800Bps T Setup of the Baud Rate of Communication As shown in Figure 2 SW2 is used to set the protocol of communication and the baud rate used by the dome camera DIP 6 and DIP 5 of SW2 are used to select the baud rate of communication and 4 different baud rates can be selected in maximum If the controller adopts non standard baud rate you can adjust it to be identical with that of the controller as per the following table Baud Rate of C ication DEX DE HPs gpa Ae au ale O Ommunication DIP 5 DIP 6
3. OFF OFF Gm 13 Operation Manual for Intelligent Speed Dome Camera 5 Selection of the Terminal Resistor of the Dome Camera As shown in Figure 2 JP is the select switch of the 120 terminal resistor on the bus RS485 on which only one terminal resistor of the dome camera at the farthest end can be connected while the terminal resistors of other devices should be opened 6 Shortcut control function Call Preset Twice Call Preset Open the menu 90 Resrved 91 1080i 59 94 Initial setting Scan limit to left 91 720 59 94 93 NTSC CROP 98 PALSQ Reserved O Reserved IV The Installation of the System 1 The style of the Installation 1 Dimension of the Product 2 The Style of Installation a Wall Installation Open the menu Scan limit to right 96 720 50 Stopscan 2n e ZA 1252 rc 719 ae Figure 3 Operation Manual for Intelligent Speed Dome Camera 4 49 4 WN a i C Ne 0199 719 a ru b In Ceiling Installation RUNG lt gt 120 142 200 Figure 4 Figure 5 Steps of Install
4. 5 5 4 CLEAR ALL PATTERNS to clear all the patterns E er 2 5 5 5 RETURN to return to the PREGRAM SETUP menu 2 5 5 6 EDIT DOME LABEL To edit the dome label Set a label for LCLEAR ALL PRELABEL each dome the label is make up of 10 characters and the SN on ren M A CLEAR ALL PATTERNS S RETURN optional character 1s the same as 2 5 1 2 2 5 7 RETURN to return to the MAIN MENU 2 6 PRIVACY MASK 2 6 0 PRIVACY MASK to set the privacy number 1 4 for optional different cameras have different choose 2 6 2 MASK SHADE to set the color of the mask area LPRIVACY MASK 01 2 MASK SHADE WHITE 3 DISPLAY ON 2 6 3 DISPLAY to ON OFF the privacy function JEDIT MASK S RE TURN 2 6 4 EDIT MASK to edit the mask area 2 6 5 RETURN to return to Main Menu 2 7 ADVANCE SETUP 2 7 1 HOME SETUP to enter the auto home submenu 2 7 1 1 AUTO HOME to set ON to open the AUTO HOME function it is mean the dome camera will back to the home position without any action in the PARK TIME And set OFF to close this function Operation Manual for Intelligent Speed Dome Camera 2 1152 HOME ACTION to set the auto home point For example if ER 1 lt HOME SETUP the user want to set one scene to be the HOME just set the 2 FAssSwoRD ID SETUP 4 c FAN CONTROL dome camera to this scene and set it to be the preset No 3 then 5 LANGUAGE ENG 6 SET NORTH POSITION open this menu set the HOME ACTI
5. ID SETUP gt 2 1 3 2 INPUT S N to input the series number of the dome 4 lt FAN CONTROL 5 LANGUAGE ENG 2 7 3 3 OLD ID to display the old address of the dome 6 SET NORTH POSITION 7 RETURN 2 7 3 4 NEW ID to display the new address of the dome Input the series number before inputting the new address CAM ID SETUP 2 7 3 5 SAVE amp RETURN to save and return to the ADVANCE 3 OLD ID 001 SETUP menu 4 NEW ID TT 5 SAVE amp RETURN 6 CANCEL amp RETURN 2 7 3 6 CANCEL amp RETURN to cancel and return to the ADVANCE 10 Operation Manual for Intelligent Speed Dome Camera SETTING menu 2 7 4 EAN CONTROL to enter the fan control setting submenu 2 7 4 1 FAN to set the work condition of the fan ON OFF AUTO 2 7 4 2 OPEN TEMP to set the work temperature of the fan under AUTO condition 2 7 4 3 Temperature Fahrenheit Celsius display switch 2 7 4 4 TEMP DISPLAY to ON OFF the display of the temperature 2 7 4 5 RETURN to return the ADVANCE SETUP menu 2 7 5 LANGUAGN to select the language 2 7 6 SET NORTH POSITION 2 8 EXIT to exit the main menu Ill Setup of the Dome Camera 1 Connection of the System 1 The Systematic Drawing of the Dome Camera Monitor VIDEO OUT ibd AC24V OUT Power IN Power Adapter ADVANCE SETUP l lt HOME SETUP gt 2 7 PASSWORD gt lt ID SETUP gt 4 lt FAN CONTROL 5 LANGUAGE ENG 6 SET NORTH POSITION T
6. gt 2 lt ANGLE DISPLAY gt i PRESET LABEL gt m 4 DOME LABEL gt 2 9 9 2 POSITION to set the display position of the preset label amp RETURN monitor when the preset position 1s setting TOP at the top of the monitor BOTTON at the bottom of JL the monitor DOME LABEL I DISPLAY 2 3 3 3 RETURN to return to the DISPLAY SETUP menu 2 POSITION J RETURN 2 3 4 DOME LABEL to enter the DOME LABEL submenu 2 54 1 DISPLAY to ON OFF the display of the dome label Operation Manual for Intelligent Speed Dome Camera 2 342 POSITION to set the display position of the dome label TOP at the top of the monitor BOTTON at the bottom of the monitor 2 3 4 3 RETURN to return to the DISPLAY SETUP menu 2 3 5 RETURN to return to MAIN MENU 2 4 CAMERA SEUP If setting camera parameter is N A it _ CAMERA SETUP Me ansthe camera can not support this function 2 4 1 D ZOOM to ON OFF the digital ZOOM 2 e OE MAN UAL 2 4 2 DISPLAY to ON OFF the display of the camera information BLC NC ON 7 SLOW SHUTTER ON v amp lt WEAE SETUP 2 4 3 FOCUS MODE NON iris amp focus invariably 9 RETURN Auto iris F AUTO Auto focus AF AUTO Auto iris and focus 244 ICR to set the AUTO DAY NIGHT situation 2 4 5 BLC to ON OFF the back light compensation 2 4 6 L SYNC to ON OFF the external synchronization Only for some special cameras 2 4 7 SLOW SHUTTER accumulation with two options Manua
7. 16 Operation Manual for Intelligent Speed Dome Camera MARK Figure 12 Figure 13 11 Rotate the vitreous cover clockwise and mount it Figure 140 Figure 14 12 Connect the control wires of the system as per Figure 15 RED CONNECTOR RED LINE AC24V IN BLACK LINE AC24V IN 1 POWER IN ORANGE LINE RS485 YELLOW LINE RS485 BLACK CONNECTOR 5 85485 CONTROL IN y NE Green Y OUT or SD Video out Blud Pb OUT Red Pr OUT S Blue ALARM IN Green ALARM IN COM Figure 15 Steps of Installation for Indoor Ceiling Style 1 Unpacking the carton and carefully take out the dome camera and its attachments 2 Take out of the bracket and fix the bracket on wall Figurel6 3 Please connect the system control wires video wires power wires with the bracket and go through it Aiming the MARK of the bracket to the MARK of the flange push the dome upward to the end and rotate 1t with the direction of the 17 V If Operation Manual for Intelligent Speed Dome Camera arrow until it is clicked and tightened Figure17 4 And then please fix the dome to the bracket with bolts Figure18 LOCK
8. 2 5 2 4 SET END LIMIT to set the end position of the scanning After the user enter this item to use the joystick to move the dome camera and press CLOSE to save the current position 2 5 2 5 RUN SCAN to run the scanning function Please set the start and end position first And if the start and end position are the same The dome MOTION SETUP camera will scanning for 360 To press CLOSE to exit 1 lt PRESETS 2 lt SCAN gt 2 5 2 6 CLEAR SCAN the clear the setting of the scanning to 5 lt CLEAR gt press CLOSE to exit 6 EDIT DOME LABEL 7 RETURN 2 92 47 RETURN to return to the PROGRAM SETUP menu 2 5 3 PATROLS to enter the submenu to set the patrols PATROLS 2 5 3 PATROL NO to set the patrol number EDIT PATROL 3 RUN PATROL 2 5 3 2 EDIT PATROL to set the parameter of the patrol after enter 4 CLEAR PATROL 5 RETURN this item the monitor 15 as following NO POS TM NO POS Patrol number POS Preset number 81 TM Stop time 0 00301 os 001 e y c i After entering into edit area 97 T screen shows as follows 09 y 10 Edit Area data of 2 patrol 11 12 position appears on one line 13 15 16 PATROL O0 It means the set No 1 patrol PATROL 01 CLOSE CLOSE EXIT 7 Press CL SE to exit edit state Both top and bottom lines display prompt and
9. 5 standards RS485 Bus is of half duplex data transmission cables with characteristic impedance as 120Q The maximum load capacity is 32 unit loads including main controller and controlled equipment 2 Transmission distances of RS485 Bus When user selects the 0 56mm 24A WG twisted pair wires as data transmission cable the maximum theoretical transmitting distances are as follows Maximum Transmitting Distance 2400 Bps 1800m 4800 Bps 1200m 9600Bps If user selects thinner cables or installs the dome in an environment with strong electromagnetic interference or connects lots of equipment to the RS485 Bus the maximum transmitting distance will be decreased To increase the maximum transmitting distance do the contrary 3 Connection and termination resistor The RS485 standards require a daisy chain connection between the equipment There must be termination resistors with 120Q impedance at both ends of the connection refer to Figure 20 Please refer to Figure 21 for simple connection D should not exceed 7m KEIN 1200 I t 1 1200 14 2f 3f 4 32 Figure 20 Y B 120Q ea Main controller E 2f 3 31 Figure 21 The connection of 120Q termination resistor T
10. Installation Operation Manual for HD Video Speed Dome Camera V1 0 Please read the operation manual carefully before installing and using this unit p 10 11 Operation Manual for Intelligent Speed Dome Camera Points for Attention Please read the operation manual carefully before installing and operating the product The product takes power supply of AC24V The rated input voltage of the camera is marked on the base or other corresponding place During the course of transportation storage and installation the product should be avoided from incorrect operations such as heavy pressing strong vibration etc which can cause damage of product as there are sophisticated optical and electronic devices inside the machine Do not attempt to disassemble the camera In order to prevent electric shock do not remove screws or covers There are no user serviceable parts inside Always follow all electrical standards for safety when it is in operation Adopt the particular power supply which is provided with the unit RS 485 and video signal should keep enough distance with high voltage equipments and cables when they are in transmission Precautions for anti lightning and anti surging should be taken if necessary Do not operate it in case temperature humidity and power supply are beyond the limited stipulations Do not let the camera aim at the sun or the object with extreme light whatsoever it 1s switched on or
11. ON to be 3 And don t 7 RETURN forget to set the AUTO HOME to be ON The HOME ACTION HOMESETUP L AUTO HOME LHOME ACTION l PATT 1 The 1 50 are the preset number RESUME is mean IEEE me SKE TURN could be the preset 1 50 RESUME PATROL 1 SCAN 1 to back to the scene before the manual control PATROL 1 15 the patrol No 1 SCAN 1 is the scanning No 1 and the PATT 1 is the pattern No 1 2 1 1 3 PARK TIME to set the park time of the dome camera it is mean how long the dome camera will be back to the HOME The time from 1 99 minutes 2 7 1 4 PWR RESUME to ON OFF the function which the dome camera will be back to the scene before the power off ADVANCE SETUP PAIS RETURN to return to the ADVANCE SETUP Menu i lt HOME SETUP 2 lt PASSWORD gt 2 7 2 PASSWORD to enter the password setting menu Initial 3 lt CAMIDSETUP gt 4 lt FAN CONTROL gt 5 LANGUAGE ENG assword is 111111 6 SET NORTH POSITION 7 RETURN PASSWORD to ON OFF the password protection MODIFY KEY to enter the new password m PASSWORD 2 7 2 9 CONFIRM KEY to enter the new password again for i PASSWORD 2 MODIFY KEY sess 3 CONFIRM KEY sem 4 RETURN confirm 2 7 2 4 RETURN to return to the ADVANCE SETUP menu 2 7 5 CAM ID SETUP to enter the soft ID setting submenu ADVANCE SETUP 27 31 CAMERA S N to display the series number of the dome oie 3 CAM
12. RETURN FAN CONTROL LOPEN TEMP EHT 3 TEMP CE 4TEMP DISPLAY RETURN oporra HH 5 9 o 9 9 NINA RS 485 RS 485 RS 485 Code Converter A RS 485 Protocol Adapter D RS 485 523 SQ gt BERSARA Philips Matrix AD Matrix 2 Address Protocol Coding Switch Drawing Figure Operation Manual for Intelligent Speed Dome Camera i oo s N lt eee SS eee 120Q terminal resistor is Protocol Set Address Set opened for RS485 bus SW DIP1 DIP4 Select Protocol 4 12 SW DIP5 DIP6 Select Baud Rate WA cae 1200 terminal resistor is connected on 9485 Bus Bracket for fixed camera Figure 2 2 Setup of Coding Switch of Dome Camera As shown in Figure 2 SWI 15 used to set address of the dome camera from 1 1023 The ID CODE from DIP 10 to DIP 1 are equivalent to a 10 bit binary digit DIP 10 is MSB while DIP 1 15 L
13. RETURN pictures in the picture PRESET NO stands for NO 1 present position the topic 15 LABEL Using PANLEFT RIGHT PRESETS can remove the cursor TILT UP DOWN can modify the number press the CLOSE exit edit mode and save it The topics of the present positions includes 10 characters at most they are 0 9 A Z blank and special characters including PRESET NO 01 Sek 01 Notes the first letter must be from 0 9 or A Z in case that it stands for canceling the preset position topic When testing the preset position it only display NO XXX not display the toptic 2 951 3 CLR LABEL to clear the preset label 2 5 14 RETURN to return to the PROGRAM SETUP submenu 2 5 2 AUTO SCAN to enter the Auto Scanning submenu MOTION SETUP 1 PRESETS gt 2 5 2 1 SCAN NO to set the auto scanning number maximum 15 lt AUTO SCAN gt 3 lt PATROLS 03 4 lt PATTERNS 5 lt CLEAR gt 6 EDIT DOME LABEL 29 2 2 SPEED to set the scanning speed for each patrol 7 RETURN 29 2 3 SET START LIMIT to set the start position of the scanning After the user enter this item to use the joystick to move AUTO SCAM the dome camera and press CLOSE to save the current Y 3 SET START LIMIT position 4 SET END LIMIT 5 RUN SCAN 6 CLEAR SCAN 7 RETURN Operation Manual for Intelligent Speed Dome Camera
14. SB The state ON of each bit means 1 while OFF means 0 Following table shows states of coding switches of some addresses Dome ID CODE Status _ Address ON OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF ON OFF OFF OFF OFF OFF OFF OFF OFF ON OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF ON OFF OFF OFF OFF OFF OFF OFF AR NE F OFF OFF OFF OFF OFF OFF OFF ON ON OFF OFF OFF OFF OFF OFF OFF on F OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF ON OFF OFF O OFF OFF OFF OFF OFF OFF OEF ON OFF _ OFF OFF OFF OFF OFF OFF For OFF OFF OFF OFF OFF OFF ON OFF ON OFF OFF OFF OFF OFF OFF orr ON on OFF OFF OFF OFF OFF OFF ON ON ON OFF OFF OFF OFF OFF OFF ie om or or o ON OFF OFF OFF OFF OFF i7 on OFF ON OFF OFF OFF OFF 18 OFF ON OFF OFF ON OFF OFF OFF OFF OFF Table 1 For Example iun 1 4 3 4 7 Speed Dome Address l Speed Dome Address TUE Dome Address 3 Vit Let ll ANE An gg
15. ation taking wall mounting as example 1 Unpacking the carton and carefully take out the dome camera and its attachments 2 Rotate the vitreous cover counterclockwise and take out it see Figure 6 Note It can be ignored the steps 2 3 4 5 while the protocol and address are matching with the controller 3 Take out the black liner Figure 7 4 Based on the ID CODE shown as Figure 2 set up the protocol used by the camera and the baud rate as per the state according to Table 1 Check the address of the camera to see if it 1s matched with that you need If not set the address of the dome camera at corresponding position as per Table 1 15 Operation Manual for Intelligent Speed Dome Camera MED p lt Takedown the Op eT bestes we lt d black liner S Figure 6 Figure 7 5 Fix the black liner see Figure 8 Fixed the black liner Figure 8 6 Take out the cover of the wall installed bracket Figure9 7 Take out system control wires from the bracket Figure 10 8 Fix the bracket on the Figurell Figure 9 Figure 10 Figurell 9 Aiming the MARK of the bracket to MARK of the flange push the dome upward to the end and rotate it with the direction of the arrow until it 1s clicked and tightened Figure 12 10 It s ok to fix the dome to the bracket with hexagon socket head cap screw Figure 13
16. em The dome will make self checking function after it carries out reset function the station for the dome s reset is AUTO FLIP ON PTZ SPD RATE ON ID DISPLAY ON ANGLE DISPLAY OFF DOME LABEL DISPLAY OFF D ZOOM OFF PT INTERLOCK AF AUTO BLC OFF AUTO HOME OFF PARK TIME 4MIN FAN AUTO TIMP DISPAY OFF 2 1 8 EXIT to quit the main menu 2 2 SYSTEM SETUP 2 2 1 SYSTEM INFORMATION to display the system information NU 2 AUTO FLIP ON 2 2 2 AUTO FLIP to ON OFF the dome 180 auto flip 5 lt ALARM SETUP gt 2 2 3 PROP PAN SPD to ON OFF the proportional pan function Vv SYSTEM INFORMATION 2 2 4 RESERVED This function seting also kept for thsi products CAME RA SN 000000 2 2 5 ALARM SETUP PROTOCOL TET a 2 2 5 1 ALARM NO to select the alarm channel VERSION 1 00 2 2 5 2 ACTION to select the action after alarm The ACTION could SYSTEM SETUP I S YSTEM INFORMATION be the preset 1 50 PATROL 1 SCAN 1 PATT 1 The aa 4 RESERVED N A 1 50 are the preset number PATROL 1 15 the patrol No 1 6 RETURN SCAN 1 is the scanning No land the PATT 1 is the pattern No 1 I After 3 seconds of the alarm function be cancelled it will ALARM SETUP IL ALARM NO 001 return to the original alarm station LACTION 001 J ALARM ON 4 RETURS 2 2 5 3 ALARM to ON OFF the alarm for each channel Operation Manual for Intelligen
17. eps the image from moving too fast on the monitor when there 15 a large amount of zoom This slowing does not happen when going to a preset but does occur in turbo mode when high zoom 15 selected The minimum pan and tilt speeds are 0 1 degree per second at full zoom The Integrated Multi Protocol Multiple communication protocols are integrated inside the dome camera with selectable baud rate from 2400 bps to 19200 bps Electrify Return Electrify return to the situation before shut Menu Password Protection function Input password to enter the menu such function ON OFF for optional The dome title display The dome title could be set to display in the dome menu Temperature display The temperature could be set to display in the dome menu Alarm Function Four channel Alarm Input One channel Alarm Output Long distance Address Modify Function To modify the dome address by RS485 2 Operation Manual for Intelligent Speed Dome Camera Principle we call hard ID HID that setting by the Dip switcher and Soft ID SID that setting by the Long distance address modify The HID and the SID are same in leaving factory For example Camera No 001 HID SID 001 we change the SID 002 by RS485 so we should select the No 002 to control it and the SID address will be remember after shut And if we change the HID 003 by Dip switcher the HID and the SID will be both change to HID SID 003 4 Functions of the Camera a Descri
18. he termination resistor is ready on the Protocol PCB There are two kinds of connection Refer to the Protocol PCB jumper setting form refer to Picture 2 1 In the Picture it is the factory default connection The jumper is seated on Pin2 amp Pin3 and the termination resistor is not connected 2 when connecting the 120Q termination resistor user should plug the jumper on Pinl amp Pin2 and the termination resistor is connected 4 Problems in practical connection In some circumstances user adopts a star configuration in practical connection The termination resistors must be connected to the two equipment that are farthest away from each other such as equipment 1 and 15 in Picture 44 As the star configuration is not in conformity with the requirements of RS485 standards problems such as signal reflections lower anti interference performance arise when the cables are long in the connection The reliability of control signals 1s decreased with the phenomena that the dome does not respond to or just responds at intervals to the controller or does continuous operation without stop refer to Figure 22 21 Operation Manual for Intelligent Speed Dome Camera Figure 22 In such circumstances the factory recommends the usage of DR HB16 RS485 distributor The distributor can change the star configuration connection to the mode of connection stipulated in the RS485 standards The new connection achieves reliable data transmission refer t
19. information of each patrol 15 displayed on the middle of the screen Data of 2 Patrol points appears on one line And to press PAN LEFT RIGHT to move the cursor to press TILT UP DOWN to modify the data to press CLOSE to save and quit the edit state 2 5 3 3 RUN PATROL to run the patrol press CLOSE to exit 2 5 34 CLEAR PATROL to clear the patrol 2 5 3 5 RETURN to return to the PROGRAM SETUP menu 2 5 4 PATTERNS to enter the PATTERN setting submenu 2 5 4 1 PATTERNS to edit the pattern number No 1 3 for optional Operation Manual for Intelligent Speed Dome Camera MOTION SETUP 2 5 4 2 RECORD PATTERN to record the pattern and press CLOSE 1 lt PRESETS gt 2 SCAN gt 3 lt PATROLS 4 lt PATTERNS gt 2 5 4 3 RUN PATTERN to run the pattern and will quit the menu 5 lt CLEAR gt 6 EDIT DOME LABEL automatically and any move of the joystick will stop this 7 RETURN to exit function _ PATTERNS 2 5 4 4 CLEAR PATTERN to clear the setting of the pattern 1 PATTERN NO 2 RECORD PATTERN 3 RUN PATTERN 2 5 4 5 RETURN to return to the superior menu 4 CLEAR PATTERN 2 5 5 CLEAR to enter CLEAR submenu 2 391 CLEAR ALL PRELABEL to clear all the preset positions MOTION SETUP 1 lt PRESETS gt 2 5 5 2 CLEAR ALL SCAN to clear all the scanning gt 3 lt PATROLS 2505 CLEAR ALL PATROLS to clear all the patrols 4 lt PATTERNS 5 lt CLEAR gt 2
20. l Automatic When camera screen 15 opened under automatic state ASS displays on screen Only sony camera has this function 2 4 8 WB AE SETUP ER i 2 4 8 1 AE MODE to set the automatic exposure to iem OE MANUAL MANU AUTO SHUTTER mode SHTTER it is only SBEC M 7 SLOW SHUTTER ON available at the AE MODE is SHUTTER dalton al 9 RETURN 2 4 8 2 WB MODE to set the white balance mode ATW MANUAL AUTO INDOOR OUTDOOR ONEPUSH WB AE SETUP R GAIN it is only available for plusing red at the WB MODE m ERN NA Is MANUAL GAIN N A 3WDRMODE B GAIN it is only available for pulsing blue at the WB MODE SETUP is MANUAL SETUP 2 4 83 WDR MODE to ON OFF the Wide Dynamic Range mode LEXPCOMP I AMGOLINT J RETURN 2 4 84 exposure compensation 2 4 8 5 exposure compensation Operation Manual for Intelligent Speed Dome Camera 2 4 8 6 AMOUNT the value of exposure compensation 7 7 24 87 RETURN to return to the WB AE SETUP menu 2 49 RETURN to return to the MAIN MANU 2 5 MOTION SETUP 2 5 1 PRESETS to enter the Preset Position submenu MOTION SETUP 2 5 1 1 PRESET NO to edit the preset number 1 lt PRESETS gt 2 lt AUTO SCAN gt 2 95 12 EDIT LABEL to edit the preset label After entering the edit R CLEAR gt mode 1 128 present positions It displayed on screen as the EMT DOME LABEL 7
21. ly Setup of the Menu of the Dome Camera 1 Basic Operation of the Menu 1 1 1 2 Open main menu of the setup by the keyboard or the matrix via the operation Call No 64 preset position or No 95 preset position Besides that continuously call No 1 preset position twice in 4 seconds you can also open the menu Through setting No 64 preset position in order to close the When the menu is displayed on the screen operate TILT UP TILT DOWN to move the cursor to the option to be set operate PAN LEFT PAN RIGHT to modify the content or the order to enter this option 1 3 setups on the menu couldn t be lost even power failure happens 2 Setup of the Menu 2 1 Zl MAIN MENU SYSTEM SETUP Operation Manual for Intelligent Speed Dome Camera 2 1 2 DISPLAY SETUP to enter the submenu of display of the screen by which ID display title display of preset point and display of camera screen can be set MAINMENU 2 1 4 CAMERA SETUP to enter the submenu of setup of normal data of 1 lt SYSTEM SETUP 2 lt DISPLAY SETUP gt 3 lt CAMERA SETUP gt Camera 4 lt MOTION SETUP gt 5 lt PRIVACY MSK gt 6 lt ADVANCE SETUP gt 2 1 4 MOTTON SETUP to enter the setup of enhanced function of eV OTTENE RESET 8 EXIT dome camera 2 1 5 PRIVACY MASK to enter the submenu of the camera privacy function setting 2 1 6 ADVANCE SETUP 2 1 7 SYSTEM RESET to reset the syst
22. maged RS485 Bus bad connection Check the RS485 connection Self check ok but cannot d Dome id setting is wrong Protocol setting is wrong Reset and on power again Bad connection of the video Press to full connect Vague 1mage Power supply not enough Replace Self check error On power again On power cannot control Bad connection of control Press to full connect Bad control of matrix On power again Video signal image Appendix Lightning Proof and Surge Signal Proof 19 Operation Manual for Intelligent Speed Dome Camera The product adopts TVS lightning proof technology to prevent from damage by lightning strike below 1500 W and impulse signals such as surge but it is also necessary to abide by the following precautions to ensure electrical safety based on practical circumstances Keep the communication cables at least 50 meters away from high voltage equipment or cables Make outdoor cable laying out under eaves as possible as you can In open area shield cables in steel tube and conduct a single point ground to the tube Trolley wire 15 forbidden in such circumstances In strong thunderstorm or high faradic zone such as high voltage transformer substation extra strong lightning proof equipment must be installed Take the building lightning proof requirements into account to design the lightning proof and grounding of outdoor equipment and cable laying out in accordance with the national and industrial standard
23. not Do not let the camera aim at or monitor bright and standstill object for a long time Do not use aggressive detergent to clean the main body of the camera Wipe dirt with dry cloth If needed mild detergent can be used suitably Operate the intelligent speed dome camera with great care to avoid shock or vibration It operate incorrectly the Speed Dome could be damaged Be careful to avoid to crash Never mount the unit on a ceiling that cannot support its weight QA M d i 7 If necessary use a commercial lens cleaning paper to clear lens windows Gently wipe the lens window until clean Operation Manual for Intelligent Speed Dome Camera II Description of Functions The intelligent dome camera 15 a hi tech CCTV product which incorporates high clarity color camera panoramic speed variable PAN TILT multifunctional decoder CPU processor memory chip into a whole It can largely reduce connection and installation processes of components in the system rise up reliability of the system and facilitate installation and maintenance Therefore it has advantages of beautiful appearance compact structure and easy operation 1 Integrated Multi Protocol Decoder a b With integrated decoder and multi protocol it can integrate 16 kinds of communication protocols in maximum As its baud rate of communication can be adjusted it 1s compatible with many normal systems by easy setup inside the dome camera so it has st
24. o Figure 23 MC2080 At 1200 1 2 3 1200 1200 164 Figure 23 Appendix IV 5 Diameter Transmission Distance Comparison Chart Wire diameter mm Distance Power a supp susp wupsup x worm _ O o om num _ ema wp euen o wm um ome _ 22 Operation Manual for Intelligent Speed Dome Camera 41 12 65 19 164 49 APPENDIX V Wire Gauge Conversion Chart Bare wire diameter Bare wire cross sectional e AWG SWG metric size area mm Approximate Approximate we wm wm _ wm wmm _ ome 0 01539 0 03142 23 Operation Manual for Intelligent Speed Dome Camera 0 290 29 31 0 06605 0 wm 5 we ws n wm am m we am 3 lw 24
25. ption of the Focus Control Mode the user can adjust the focus of the camera manually When the camera is on near focus the icon 4 appears on the screen when on the nearest state the icon amp appears while on the far focus the icon appears Description of Backlight Compensation when the object to be shot is dark and looks dim the user can open the backlight compensation according to actual need and the icon appears on the screen Description of White Balance when the image has color distort on the screen the user can set different modes by orders There are 6modes for options Indoor Mode Outdoor Mode Touch Mode Automatic Trace of White Balance ATW 1 Manual WB MAN Automatic Mode Description of ZOOM Control user can pull near or push far the lens according to actual conditions and the symbol V amp E T appears on the screen in which the front part means optical multiplication while the rear part means digital multiplication Electron shutter it is 1 50 sec after the camera electrified and it will display 50 on the monitor AE Mode setup of Manual Automatic Zero Illuminance It 15 used only when the external brightness 15 extremely low Normally the camera works on the automatic state In case the external brightness 15 lower than 1 Lux the camera be switch to the Zero Illuminance state automatically and icon appears on the screen You can also set the Zero Illuminance state manual
26. ronger versatility RS485 serial control addresses of camera 1 1023 2 Integrated speed variable PAN TILT a b C Turni ng 360 horizontally and continuously with unlimited positions and an adjustable speed from 0 300 s turning 0 90 vertically with a speed up to 120 s Running stably at low speed with super lower noise Pictures have no shaking the location precision up to x 0 1 3 High Intelligent Degree a b C PE SUY As much as 128 preset positions can be preset with powerless memory The camera can scan horizontally between two points and scan speed can be modified The positions of linear scan are optional and the dome camera can scan the range larger or smaller than 180 between any two points with adjustable speed Six sets of programmable patrol with 16 position each set the detention time are adjustable respectively The self learning function of the locus 3 loci the time length of each locus 1s more than 120 seconds with powerless memory Character Overlapping The humane structure of the menu makes all setups and programming of the dome camera more convenient and easy Angle display The dome could display the panning angle tilting angle and the view angle of the camera Proportional pan function The speed dome will depend on the amount of zoom At telephoto zoom settings the pan and tilt speeds will be slower for a given amount of Joystick deflection than at wide zoom settings This ke
27. s The system must be grounded with equal potentials The earth ground connection must satisfy the anti interference and electrical safety requirements and must not short circuited with high voltage electricity net When the system 15 grounded separately the resistance of down conductor should be lt 40 and the sectional area of down conductor should be 25mm2 refer to Figure 19 Video cable S ift lar cabo lgnining conduce les isghining red Poser noD gh limg Gord ioe kou Thee mud within the 5 angle area et Ure the with the vertical iing me bisecior of hgud be o 8 Sheet Sue Figure 19 Appendix l The Cleaning of Clear Down Cover To obtain constant clear videos user should clean the down cover periodically Be cautious when cleaning Hold the down cover ring only to avoid direct touch to the acrylic down cover The acid sweat mark of fingerprint will corrode the coating of down cover and scratch on down cover will cause vague images Use soft dry cloth or the substitute to clean the inner and outer surfaces For hard contamination use neutral detergent Any cleanser for high grade furniture is applicable Appendix Ill RS485 Bus Basic Knowledge 1 Characteristics of RS485 Bus 20 Operation Manual for Intelligent Speed Dome Camera As specified by RS48
28. t Speed Dome Camera 2 2 5 4 RETURN to return to the SYSTEM SETUP menu DISPLAY SETUP L CAMERA ID 2 2 6 RETURN to return to the main menu 1 ANGLE DISPLAY 1 PRESET LABEL gt 2 3 DISPLAY SETUP n d 2 3 CAMERAID when it 1s set at ON address of dome camera appears on the screen such as 001 The default setting CAMERA ID DISPLAY is ON 2 POSITION TOP R 3 RETURN 2 3 1 1 DISPLAY to ON OFF the dome address 2 3 1 3 POSITION to set the position of dome address there are DISPLAY SETUP four positions to be displayed TOP L top left corner 3 lt PRESET LABEL gt TOP R 4 lt DOME LABEL gt 5 RETURN top right corner BOTT R bottom right corner AND BOTT L bottom left corner NGLE DISPLAY ANG AX 2 3 1 3 RETURN to return to the DISPLAY SETUP menu 3 RETURN 2 3 2 ANGLE DISPLAY to enter the angel display submenu 2198241 DISPLAY to ON OFF the angle display ONEPUSH singly L CAMERA 10 gt 2 lt ANGLE DISPLAY 4 lt PRESET LABEL gt E 4 lt DOME LABEL 2 3 2 2 POSITION to set the display position of the angle amp RETURN displayed auto disappeared in 4 seconds TOP BOTTOM PRESET LABEL 2323 RETURN to return to the DISPLAY SETUP menu Tem 2 POSITION 2 3 3 PRESET LABEL to enter the PRESET LABEL submenu 3 RETURN 2 5 9 DISPLAY to ON OFF the display of the preset label If it is ON the preset label will be displayed on the left of the L lt CAMERA ID
Download Pdf Manuals
Related Search