HP S 845 (H)
Contents
1. ELECTRONIC ADVANCE LINE HPS 845 H USER MANUAL CANBUS Analog Car alarm and anti hi jack System with additional PATROLLINE remote controls November 2010 Operation with default remote control ALARM ARMING Push closing button of default remote control of the vehicle The arming will be confirmed by the followings o Blinker flashing based on closing features of the vehicle e 1 beep if it is programmed Switching ON of the LED on the dashboard e Activation of electric engine immobilization if it was connected Activation of module outputs optional ultrasonic sensors hyperfrequency etc The CDL closes the doors ALARM DISARMING Push opening button of default remote control of the vehicle The disarming will be confirmed by the followings e 2 beeps if it is programmed Switching OFF of the LED on the dashboard e Deactivation of electric engine immobilizer if it was connected Deactivation of module outputs optional ultrasonic sensors hyperfrequency etc The CDL opens the doors Blinker flashing based on opening features of the vehicle November 2010 Operation with optional PATROLLINE remote control ALARM ARMING Push closing button Nr 3 of the PATROLLINE remote control The arming will be confirmed by the followings Blinker flashing if it is programmed 1 beep if it is programmed Switching ON of the LED on the dashboard Activation of electric engine2. 15 seconds the CDL closes back automatically the doors and in same time the alarm switches ON Warning In those cars in which there isn t automatic CDL closing back function ask the installer to program automatic rearming function of the alarm If it is programmed automatic rearming function of the alarm will operate but the CDL will close if the alarm was connected for it at installation After programming automatic rearming function of the alarm this function will operate with the optional PATROLLINE remote controls too according to the above mentioned Status memory If the armed alarm is disconnected from its connector after the reconnection it will stay in armed status protected the car further Anti hi jack function The alarm can immobilize the engine while the engine is ON when somebody hijack the car This function is disarmed defaulty Arming of this function can happen based on request of the client in writing To arming of the function please contact with the installer November 2010 The alarm can immobilize the engine when somebody hijacks the car together with its own keys This function is disarmed defaulty Arming of this function can happen based on request of the client in writing Antiagression function To arming of the function please contact with the installer If the central unit records one or more triggering causes after disarming of the alarm it will show the triggering cause at opening of the
3. button too early or too late you have to start the procedure from starting Deactivation of the valet function At disarmed alarm sit into the car All doors of the vehicle have to be closed Turn ON the ignition key and immediately push and keep pushed anti hi jack button of the alarm what was installed into the vehicle After 10 seconds LED of the alarm on the dashboard starts trigger and it flashes till 5 seconds Till the LED flashes let off the anti hi jack button By this time the LED flashes four times slowly signed disarming of the valet function If you let off the anti hi jack button too early or too late you have to start the procedure from starting To remind activated status of the valet function the LED will flash continuously twice if you turn ON the ignition key 2 Valet function usage with ignition key this function operates too if the PIN code emergency switching OFF function is programmed for the 3 operating opportunity for the PIN code emergency switching OFF on ignition ON automatically operation Activation of the Valet function At disarmed alarm turn ON and OFF the ignition key as many time as first digit of the PIN code of the alarm During turn ON the ignition key the LED is ON and after the first digit you have to wait to switch OFF the LED After that immediately turn ON and OFF the Deactivation of the Valet function Turn ON and OFF the ignition key as many time as first digit of
4. the alarm discovered the remote control November 2010 LED flashes quickly If the distance is too big between the alarm and the remote control and the alarm doesn t sense the remote control signal at pushing of each button the LED flashes quickly LED 4 slow flashings If you have to change battery in the remote control after pushing of each button the LED immediately flashes 4 With help of the PATROLLINE remote control you can check that the car alarm was armed or it is in disarmed status You can check the alarm status only with that PATROLLINE remote control with which the alarm was disarmed or armed latest Push Nr 1 opening and Nr 3 closing button of the remote control in same time by this time LED of the remote control signs armed or disarmed status of the alarm in big distance too from the car LED flashes quickly The alarm was armed with this PATROLLINE remote control LED is OFF The alarm was disarmed with this PATROLLINE remote control Neutral time armed status After the alarm was armed with the default OEM remote control or with the PATROLLINE remote control the alarm will arm in the next 10 seconds what signaled by the fixed light of the LED During this time if each sensor will be tested the alarm will sign it with blinker flashing number of the blinker flashing shows cause of the triggering as table shows it in Alarm memory paragraph The flashing of the LED on the dashboard will in
5. ANCE November 2010
6. dicate that the system is ready to react with acoustic optic signal for triggering cause Triggering After the inhibition time the alarm will be in armed status The alarm will react with optic acoustic signal for triggering event it will make to operate the horn or siren and it will make to flash the blinkers Time of the triggering cycle is 30 seconds To stop the triggering without disarming of the alarm push Closing button of the default remote control or Nr 2 panic button of the PATROLLINE remote control To stop the triggering and disarming of the alarm push Opening button of the default remote control or Nr 1 opening button of the PATROLLINE remote control November 2010 Panic triggering After the inhibition time if Nr 2 panic button of the PATROLLINE remote control or closing button of the default remote control was pushed the alarm will trigger till 30 seconds beep acoustic signal Warning You have to activate the panic function to operate it Ask help of the installer to the activation Ultrasonic Hyperfrequency Default shock sensor exclusion This function is necessary if you can leave dogs or cats in the car without triggering of the alarm In active status of the function other senses of the alarm operate just the interior protection and the default shock sensor don t operate After locking during inhibition time push closing button of the default or PATROLLINE remote control to switch OFF operatio
7. driver s door or at pushing of the anti hi jack button through the Alarm memory LED To verify type of triggering check number of flashings of the LED with the table below N flashings of the LED CAUSE DOORS OPENING WITH CAN BUS SIGNAL AND TRIGGERING BY ADDITIONAL INPUT BLUE WHITE WIRE INPUT DRIVER S DOOR OPENING WITH MECHANICAL KEY WITH CAN BUS SIGNAL BONNET OPENING WITH CAN BUS SIGNAL TRUCK OPENING WITH CAN BUS SIGNAL IGNITION PROTECTION WITH CAN BUS SIGNAL OR THROUGH THE GREEN BLACK WIRE SHOCK SENSOR ULTRASONIC SENSOR ADDITIONAL INPUT BLUE WIRE ADDITIONAL SENSOR BLUE RED WIRE INPUT RADIO OPENING SENSOR OR MOVING SENSOR BONNET OPENING WITH ANALOG SIGNAL GAS SENSOR RADIO FREQUENCY DISTURBING November 2010 Safety function Door protection Senses door trunk and bonnet opening Engine block Prevents starting of the engine of the car Shock sensor Senses the broke of the door s window Ignition protection Senses the ignition of the car Ultrasonic Option Sense moving in the passenger compartment Anti hi jack Triggers in case of running engine and it can block the engine if somebody Steal the car l l Triggers at starting of the car with its own key and it can block the engine if Antiagression somebody wants to steal the car PIN code The PIN code is for that the user can sw
8. e into consideration the polarity what is located on side of the battery Use litium battery CR 2032 in case of the optional PATROLLINE remote control Suggested the battery changing in every 2 years Vehicle cleaning should you clean the vehicle via high pressure beams hydro beam or similar please protect the siren prior to commence cleaning The alarm warranty will be cancelled if water is detected into the alarm Main maintenance All repairs must be carried at PATROLLINE assistance centers Alarm systems pampering by non authorized personnel may invalidate alarm feasibility as well as your vehicle safety Declaration of conformity This product harmonizes with the followings E ECE 324 E ECE TRANS 505 Regulation No 116 gt gt Rev 2 Add 115 European Directive so it satisfies all the requirements asked about the functionality of the alarm devices and for the electromagnetic compatibility The installation certificate of the alarm included in the box must be properly filled in every section and it will be part of the documentation of the vehicle It is required to write the following homologation number on the installation certificate to complete the conformity with the directive 116R A 000031 Note Patrolline Kft 8000 Sz kesfeh rv r Kiralysor 30 i y we e LINE Tel Fax 36 22 317 367 36 22 503 078 E mail info riasztocentrum hu Web www canbusriaszto hu www patrolline eu ELECIRONIC ADV
9. emporarily with twice pushing of closing button of the remote controls Exclusion of siren With help of the default remote control and the PATROLLINE remote control too it is possible to be excluded the horn or siren function In case of usage of default remote control At disarmed alarm CDL opened turn ON and OFF the ignition key for 3 times and within 30 seconds push the default remote control to close the CDL November 2010 At this time the central unit will sign the attempt to break in by the flashing of the blinkers only IGNITION KEY On Off On Off On Off Push the original remote With CDL open 1 Oo 1 control to close the doors LED off within 30 seconds ist time 2nd time 3rd time In case of usage of PATROLLINE remote control After arming of the alarm within the 10 seconds inhibition time push Nr 2 button of the PATROLLINE remote control from this time the device signs the triggering only with the blinker flashing 4 beeps and 4 blinker flashings will confirm the exclusion Warning The siren exclusion is valid for only one triggering cycle If you switch OFF the alarm with the default or PATROLLINE remote control the system will be restored automatically in original state and for the next arming it will react with beep and acoustic signals for every triggering causes Automatic rearming If the alarm was disarmed with default remote control of the vehicle but the doors didn t open within
10. gression and keep it pushed until the procedure wasn t finished Modification of the PIN code Modification of the PIN code is necessary if the client wants to modify the default PIN code for a personalized PIN code Warning We suggest to user of the product to modify the default PIN code for a new personalized PIN code To modify the PIN code do the following instructions with ignition key of the vehicle At disarmed alarm turn ON and OFF the ignition key as many time as first digit of the PIN code During turn ON the ignition key the LED is ON and after the first digit you have to wait to switch OFF the LED After that immediately turn ON and OFF the ignition key as many time as the second digit After the LED switching OFF turn ON and OFF the ignition key as many time as the third digit After that the LED flashes some times Turn ON and OFF the ignition key as many time as first digit of the new PIN code while the LED flashes During turn ON the ignition key the LED is ON and after the first digit you have to wait to switch OFF the LED After that immediately turn ON and OFF the ignition key as many time as second digit of the new PIN code After the LED switching OFF turn ON and OFF the ignition key as many time as third digit of the new PIN code If the procedure was successful the LED signs it with quick flashing After that only the new PIN code is usable If PIN code function of the alarm was programmed for brake pedal ha
11. hat immediately push draw the brake pedal hand brake as many time as the second digit After the LED switching OFF push draw the brake pedal hand brake as many time as the third digit The LED flashes some times signed arming of the valet function Deactivation of the Valet function Turn ON the ignition key and push draw the brake pedal hand brake as many time as first digit of the PIN code During push draw of the brake pedal hand brake the LED is ON after the first digit you have to wait to switch OFF the LED After that immediately push draw the brake pedal hand brake as many time as the second digit After the LED switching OFF push draw the brake pedal hand brake as many time as the third digit After that the valet function will be in disarmed status To remind activated status of the valet function the LED will flash continuously twice if you turn ON the ignition key WARNING If the Antitheft Antiagression function are programmed before starting of the procedure push the secret button used to the Antitheft Antiagression and keep it pushed until the procedure wasn t finished except the 1 Valet function with antitheft button mode Alarm maintenance Our alarms are sophisticated systems The reliability as well as time life may be furthermore incremented just adopting some precautions such as November 2010 Battery changing Open box of the remote control remove the old battery and put the new Tak
12. immobilization if it was connected Activation of module outputs optional ultrasonic sensors hyperfrequency etc The CDL closes the doors if the alarm was connected to it ALARM DISARMING Push opening button Nr 1 of the PATROLLINE remote control The disarming will be confirmed by the followings 2 beeps if it is programmed Switching OFF of the LED on the dashboard Deactivation of electric engine immobilization if it was connected Deactivation of module outputs optional ultrasonic sensors hyperfrequency etc The CDL opens the doors if the alarm was connected to it Blinker flashing if it is programmed Special functions of PATROLLINE remote control The HPS 845 H device defaulty doesn t contain remote controls maximum 4 pieces PATROLLINE remote control can be memorized only optionally The PATROLLINE remote controls use 2 4 GHz technology uniquely in Europe Thanks to this innovative technology the PATROLLINE remote controls with the alarm are able for 2 ways communication Therefore it is possible that with special application of the remote control buttons you can control the last did procedure Unique application of the 2 ways communication provides the opportunity that different feedbacks of the remote control LED show that the connection created or not between the remote control and the alarm LED is fix ON If each button of the remote control was used the LED of the remote control is fix ON showed that
13. itch OFF the alarm if the remote control or the alarm get wrong or the battery discharged in the remote control PIN code emergency switching OFF function of the alarm dependent on alarm programming has 3 types operating opportunities which are the followings 1 PIN code emergency switching OFF with ignition key it is default setting of the alarm 2 PIN code emergency switching OFF with usage of brake pedal hand brake this function can be used after programming of the alarm 3 PIN code emergency switching OFF on ignition key ON automatically this function can be used after programming of the alarm In all boxes of the alarms can be found an envelop which contains the secret PIN code Only the user can open this envelop Every alarm has different PIN code We suggest for the user as for the perfect safety to change the original set PIN code for a new own one Please follow the next instructions in the followings chapters If you have got any further problem with the PIN code please look for only your importer Open only by the USER November 2010 Usage of the PIN code is necessary when the remote control lost or the battery was flat or the alarm went wrong but the device is in switched ON status Dependent on equipment of the cars it can be necessary to change the PIN code emergency switching OFF operation for example in that case if the vehicle is equipped with START amp GO system by this time we suggest
14. n of the ultrasonic hyperfrequency default shock sensor The alarm signs exclusion of the ultrasonic hyperfrequence default shock sensor with 3 blinker flashings and 3 beeps Default shock sensor exclusion with optional PATROLLINE remote control This function is that the alarm doesn t trigger for vibrations concern the car In active status of the function other senses of the alarm operate just the default shock sensor doesn t operate After locking during inhibition time push Nr 2 and 3 button of the PATROLLINE remote control in same time to switch OFF the default shock sensor The alarm signs exclusion of the shock sensor with 5 blinker flashings and 5 beeps Warning This function is usable only with the optional PATROLLINE remote control not with default remote control of the car Operation with optional wireless opening sensor Optional PATROLLINE wireless opening sensors can be memorized for the HPS 845 H device With help of them opening sensation of buildings e g garage or door of campers can be solved in near of the vehicle in which HPS 845 H device is installed In case of cracking of the garage door or camper door HPS 845 alarm installed into the vehicle will trigger These sensors can be memorized in 2 safety zones of the HPS 845 H alarm maximum 24 pieces in zone 1 maximum 8 pieces in zone 2 Difference between the two zones is that sensors memorized in zone 2 similar to the ultrasonic can be disarmed t
15. nd brake mode you have to do the above procedure on same way only you have to push draw the brake pedal hand brake instead of turn ON OFF the ignition key WARNING If the Antitheft Antiagression function are programmed before starting of the procedure push the secret button used to the Antitheft Antiagression and keep it pushed until the procedure wasn t finished Valet function This function is that during service of the vehicle operating functions of the alarm are suspension Usage of the valet function has independently from programming of the alarm 3 types operating opportunities which are the followings November 2010 1 Valet function with anti hi jack button 2 Valet function with ignition key 3 Valet function with usage of brake pedal hand brake this function can be used after programming of PIN code emergency switching OFF function of the alarm 1 Valet function usage with anti hi jack button Activation of the valet function At disarmed alarm sit into the car All doors of the vehicle have to be closed Turn ON the ignition key and immediately push and keep pushed anti hi jack button of the alarm what was installed into the vehicle After 10 seconds LED of the alarm on the dashboard starts trigger and it flashes till 5 seconds Till the LED flashes let off the anti hi jack button By this time the LED flashes twice slowly signed arming of the valet function If you let off the anti hi jack
16. r s door with mechanical key The alarm starts trigger by this time turn ON the ignition key and push draw the brake pedal hand brake as many time as first digit of the PIN code the brake pedal hand brake operate with CAN BUS signals not in every car types therefore they can t be used for PIN code emergency switching OFF not in every cars During push draw of the brake pedal hand brake the LED is ON after the first digit you have to wait to switch OFF the LED After that immediately push draw the brake pedal hand brake as many time as the second digit After the LED switching OFF push draw the brake pedal hand brake as many time as the third digit If the procedure was successful the alarm switches OFF If the procedure was unsuccessful the alarm stays in armed status and triggers by this time you have to restart the PIN code emergency switching OFF procedure from first digit giving of the PIN code 3 PIN code emergency switching OFF on ignition key ON automatically this function can be used after programming of the alarm At armed alarm open the driver s door with mechanical key The alarm starts trigger by this time turn ON the ignition key and the transponder identifies the default key and through the CAN BUS network the alarm will be disarmed automatically November 2010 WARNING If the Antitheft Antiagression function are programmed before starting of the procedure push the secret button used to the Antitheft Antia
17. the PIN code of the alarm During turn ON the ignition key the LED is ON and after the first digit you have to wait to switch OFF the LED After that immediately turn ON and OFF the ignition key as many time as the second digit ignition key as many time as the second digit November 2010 After the LED switching OFF turn ON and OFF the ignition key as many time as the third digit The LED flashes some times signed arming of the valet function After the LED switching OFF turn ON and OFF the ignition key as many time as the third digit After that the valet function will be in disarmed status To remind activated status of the valet function the LED will flash continuously twice if you turn ON the ignition key 3 Valet function usage with brake pedal handbrake this function operates too if the PIN code emergency switching OFF function is programmed for the 2 operating opportunity for the PIN code emergency switching OFF with usage of brake pedal hand brake operation Activation of the Valet function At disarmed alarm turn ON the ignition key and push draw the brake pedal hand brake as many time as first digit of the PIN code the brake pedal hand brake operate with CAN BUS signals not in every car types therefore they can t be used for valet function not in every cars During push draw of the brake pedal hand brake the LED is ON after the first digit you have to wait to switch OFF the LED After t
18. to program the alarm for the 2 or 3 emergency switching OFF operating mode instead of the default setting of the PIN code emergency switching OFF function Only importer of PATROLLINE and his contracted partners can do the programming of the alarm because special software and hardware is necessary to it 1 PIN code emergency switching OFF with ignition key it is default setting of the alarm The PIN code is a 3 figures number e g 1 2 3 If you would like to use the PIN code do the following instructions with ignition key of the vehicle At armed alarm open the driver s door with mechanical key The alarm starts trigger by this time turn ON the ignition key and turn OFF the ignition key as many time as first digit of the PIN code During turn ON the ignition key the LED is ON after the first digit you have to wait to switch OFF the LED After that immediately turn ON and OFF the ignition key as many time as the second digit After the LED switching OFF turn ON and OFF the ignition key as many time as the third digit If the procedure was successful the alarm switches OFF If the procedure was unsuccessful the alarm stays in armed status and triggers by this time you have to restart the PIN code emergency switching OFF procedure from first digit giving of the PIN code 2 PIN code emergency switching OFF with usage of brake pedal hand brake this function can be used after programming of the alarm At armed alarm open the drive
Download Pdf Manuals
Related Search